COMMUNICATIONS MODULES & SUBSYSTEMS 8.5 G SFP+ 850 nm Limiting Transceiver, 8 Gigabit Fibre Channel Compliant PLRXPL-VC-SH4-21-N and PLRXPL-VC-SH4-22-N Series Key Features • Compliant to industry-wide, 8 G Fibre Channel (FC) link specifications • Maintains FC compliance at 4 and 2 G without need for a rate select option • Uses a highly reliable, 850 nm oxide VCSEL • Lead-free and RoHS 6/6-compliant • 0 – 70°C case operating temperature • Single 3.3 V power supply • Low power consumption (typically 450 mW) • Bit error rate < 1 x 10-12 • Hot pluggable Applications • High-speed storage area networks - Switches and hubs - Network interface cards - Mass storage systems - Host bus adapters • Computer cluster crossconnect systems • Custom high-bandwidth data pipes Compliance • • • • • • • • • SFF 8431 Revision 2.2 FC-PI-4 SFF 8432 Revision 5.0 SFF 8472 Revision 10.3 CDRH and IEC60825-1 Class 1 Laser Eye Safety FCC Class B ESD Class 2 per MIL-STD 883 Method 3015 UL 94, V0 Reliability tested per Telcordia GR-468 NORTH AMERICA: 800 498-JDSU (5378) The lead-free and RoHS-compliant small form factor pluggable (SFP+) transceiver from JDSU improves the performance for 8 Gigabit Fibre Channel (8 G FC) applications, and is ideal for high-speed, storage area network applications. This transceiver features a highly reliable, 850 nm, oxide, vertical-cavity surfaceemitting laser (VCSEL) coupled to an LC optical connector. The transceiver is fully compliant to the 8 G FC, FC-PI-4, and the SFP+ multisource agreement (MSA) specifications, with internal AC coupling on both transmit and receive data signals. The all-metal housing design provides low EMI emissions in demanding 8 G applications and conforms to IPF specifications. An enhanced digital diagnostic feature set allows for real-time monitoring of transceiver performance and system stability, and the serial ID allows for customer and vendor system information to be stored in the transceiver. Transmit disable, loss-of-signal, and transmitter fault functions are also provided. The small size of the transceiver allows for highdensity system designs that, in turn, enable greater total bandwidth. WORLDWIDE: +800 5378-JDSU WEBSITE: www.jdsu.com 8.5 G SFP+ 850 NM LIMITING TRANSCEIVER, 8 GIGABIT FIBRE CHANNEL COMPLIANT 2 Section 1 Functional Description The PLRXPL-VC-SH4-xx-N 8.5 G SFP+ 850 nm optical transceiver is designed to transmit and receive 8B/10B scrambled 8.5 G serial optical data over 50/125 µm or 62.5/125 µm multimode optical fiber. Transmitter The transmitter converts 8B/10B scrambled serial PECL or CML electrical data into serial optical data compliant with the 8 G Fibre Channel standard. Transmit data lines (TD+ and TD-) are internally AC coupled, with 100 Ω differential termination. Transmitter rate select (RS1) pin 9 is assigned to control the SFP+ module transmitter rate. It is connected internally to a 30 kΩ pull-down resistor. A data signal on this pin does not affect the operation of the transmitter. An open collector-compatible transmit disable (Tx_Disable) is provided. This pin is internally terminated with a 10 kΩ resistor to Vcc,T. A logic “1,” or no connection, on this pin will disable the laser from transmitting. A logic “0” on this pin provides normal operation. The transmitter has an internal PIN monitor diode that ensures constant optical power output, independent of supply voltage. It is also used to control the laser output power over temperature to ensure reliability at high temperatures. An open collector-compatible transmit fault (Tx_Fault) is provided. The Tx_ Fault signal must be pulled high on the host board for proper operation. A logic “1” output from this pin indicates that a transmitter fault has occurred or that the part is not fully seated and the transmitter is disabled. A logic “0” on this pin indicates normal operation. Receiver The receiver converts 8B/10B scrambled serial optical data into serial PECL/CML electrical data. Receive data lines (RD+ and RD-) are internally AC coupled with 100 Ω differential source impedance, and must be terminated with a 100 Ω differential load. Receiver Rate Select (RS0) pin 7 is assigned to control the SFP+ module receiver rate. It is connected internally to a 30 kΩ pull-down resistor. A data signal on this pin has no affect on the operation of the receiver. An open collector compatible loss of signal (LOS) is provided. The LOS must be pulled high on the host board for proper operation. A logic “0” indicates that light has been detected at the input to the receiver (see Optical Characteristics, Loss of Signal Assert/Deassert Time). A logic “1” output indicates that insufficient light has been detected for proper operation. 8.5 G SFP+ 850 NM LIMITING TRANSCEIVER, 8 GIGABIT FIBRE CHANNEL COMPLIANT 3 10 kΩ 16 Transmitter Power Supply 3 Transmitter Disable In VCC_TX TX_DIS TOSA Laser Driver TX_GND 18 Transmitter Positive Data TD+ 100 Ω 19 Transmitter Negative Data TD - TX_FAULT 2 Transmitter Fault Out 1, 17, 20 Transmitter Signal Ground 5 SCL Serial ID Clock 4 SDA Serial ID Data SCL Management Processor EEPROM SDA 6 MOD_ABS 15 Receiver Power Supply VCC_RX VCC_RX RD - 50 Ω Receiver ROSA RD + RX_GND RX_GND 50 Ω LOS 12 Receiver Negative Data Out 13 Receiver Positive Data Out 8 Loss of Signal Out 9 RS1 TX Rate Select Not Functional on -N modules 30 kΩ 30 kΩ 7 RS0 RX Rate Select Not Functional on -N modules 10, 11, 14 Receiver Signal Ground Figure 1 SFP+ optical transceiver functional block diagram 8.5 G SFP+ 850 NM LIMITING TRANSCEIVER, 8 GIGABIT FIBRE CHANNEL COMPLIANT 4 Section 2 Application Schematic Vcc � � 1 VeeT VeeT 20 Vcc � � � Rp*** 2 Tx Fault TD- 19 3 Tx Disable TD+ 18 � � � � R2* 50 Ω CMOS, TTL, or Open Collector Driver (Tx Disable) Power Supply Filter Rx VeeT 17 � � VccT 16 6 MOD_ABS VccR 15 7 RS0 VeeR 14 8 LOS RD+ 13 9 RS1 RD- L2 C2 Vcc CMOS or TTL Driver (RS0 Rx Rate Select) C4 Z* = 100 Ω 12 R3* 50 Ω Vcc R6 ∗∗ 10 VeeR VeeR 11 R4* 50 Ω � � � � Receiver (LOS) � � 10 kΩ Ry � � � � Vcc C5 C1 � R5 ∗∗ Mod_ABS � Vcc 10 kΩ � 5 SCL � *** Vcc +3.3V Input � � � � Rq L1 C6 C3 � 4 SDA Vcc Open Collector Bidirectional SCL PECL Driver (TX DATA) � � � � Receiver (Tx Fault) Open Collector Bidirectional SDA R1* 50 Ω Z* = 100 Ω 10 kΩ PECL Receiver (RX DATA) CMOS or TTL Driver (RS1 Tx Rate Select) Power supply filter component values are provided on page 7. Figure 2 Recommended application schematic for the 10 G SFP+ optical transceiver Notes Power supply filtering components should be placed as close to the Vcc pins of the host connector as possible for optimal performance. PECL driver and receiver components will require biasing networks. Please consult application notes from suppliers of these components. CML I/O on the PHY are supported. Good impedance matching for the driver and receiver is required. SDA and SCL should be bi-directional open collector connections in order to implement serial ID in JDSU SFP+ transceiver modules. R1/R2 and R3/R4 are normally included in the output and input of the PHY. Please check the application notes for the IC in use. * Transmission lines should be 100 Ω differential traces. Vias and other transmission line discontinuities should be avoided. In order to meet the host TP1 output jitter and TP4 jitter tolerance requirements it is recommended that the PHY has both transmitter pre-emphasis to equalize the transmitter traces and receiver equalization to equalize the receiver traces. With appropriate transmitter pre-emphasis and receiver equalization, up to 8 dB of loss at 5 GHz can be tolerated. ** R5 and R6 are required when an Open Collector driver is used in place of CMOS or TTL drivers. 5 kΩ value is appropriate. *** The value of Rp and Rq depend on the capacitive loading of these lines and the two wire interface clock frequency. See SFF-8431. A value of 10 kΩ is appropriate for 80 pF capacitive loading at 100 kHz clock frequency. 8.5 G SFP+ 850 NM LIMITING TRANSCEIVER, 8 GIGABIT FIBRE CHANNEL COMPLIANT 5 Power supply filtering is recommended for both the transmitter and receiver. Filtering should be placed on the host assembly as close to the Vcc pins as possible for optimal performance. Vcc,R and Vcc,T should have separate filters. Power supply filter component values from Figure 2 are shown in the table below for two different implementations. Power Supply Filter Component Values Component Option A Option B Units L1, L2 Rx, Ry C1, C5 C2, C3, C4 C6 1.0 0.5* 10 0.1 Not required 4.7 0.5* 22 0.1 22 µH Ω µF µF µF Notes: Option A is recommended for use in applications with space constraints with power supply noise less than 33 mVp-p. Option B is used in the module compliance board in SFF-8431. *If the total series resistance of L1+C6 and L2+C5 exceeds the values of Rx and Ry in the table, then Rx and Ry can be omitted. 8.5 G SFP+ 850 NM LIMITING TRANSCEIVER, 8 GIGABIT FIBRE CHANNEL COMPLIANT 6 Section 3 Specifications Technical specifications related to the SFP+ optical transceiver include: • Section 3.1 Pin Function Definitions • Section 3.2 Absolute Maximum Ratings • Section 3.3 Operating Conditions • Section 3.4 Electrical Characteristics • Section 3.5 Optical Characteristics • Section 3.6 Link Length • Section 3.7 Regulatory Compliance 2.2 P IN F UNCTION D EFINITIONS • Section 3.8 PCB Layout • Section 3.9 Front Panel Opening • Section 3.10 inModule The transceiver pin descriptions as defined in SFF-8431 are shown Figure 3 Outline below. Table 2 on page 8 has a • Section 3.11 Transceiver Belly-to-belly Mounting complete description of all the pins. Figure 3 Host PCB SFP+ Pad Assignment Top View 3.1 11 TOWARD HOST WITH DIRECTION OF MODULE INSERTION November 2007 21114472 R2 Pin Function Defi nitions VEER 10 VEER RS1 12 9 RD- RX_LOS 8 13 RD+ RS0 7 14 VEER MOD_ABS 6 15 VCCR SCL 5 16 VCCT 17 VEET 18 TD+ 19 TD- 20 VEET Figure 3 SDA 4 TX_DISABLE 3 TX_FAULT 2 VEET 1 Host PCB SFP+ Pad assignment top view TOWARD BEZEL PLRXPL-Vx-SH4-21xN JDSU | p. 7 of 20 8.5 G SFP+ 850 NM LIMITING TRANSCEIVER, 8 GIGABIT FIBRE CHANNEL COMPLIANT 7 SFP+ Optical Transceiver Pin Descriptions Pin Number Symbol Name Description Receiver 8 LOS Loss of Signal Out (OC) 10, 11, 14 12 VeeR RD- Receiver Signal Ground Receiver Negative DATA Out (PECL) 13 RD+ Receiver Positive DATA Out (PECL) 15 VccR Receiver Power Supply 7 RS0 RX Rate Select (LVTTL) Sufficient optical signal for potential BER < 1x10-12 = Logic “0” Insufficient optical signal for potential BER < 1x10-12 = Logic “1” This pin is open collector compatible, and should be pulled up to Host Vcc with a 10 kΩ resistor. These pins should be connected to signal ground on the host board. Light on = Logic “0” Output Receiver DATA output is internally AC coupled and series terminated with a 50 Ω resistor. Light on = Logic “1” Output Receiver DATA output is internally AC coupled and series terminated with a 50 Ω resistor. This pin should be connected to a filtered +3.3 V power supply on the host board. See Application schematics on page 4 for filtering suggestions. This pin has an internal 30 kΩ pull-down to ground. A signal on this pin will not affect module performance. Transmitter 3 TX_Disable Transmitter Disable In (LVTTL) 1, 17, 20 2 VeeT TX_Fault Transmitter Signal Ground Transmitter Fault Out (OC) 16 VccT Transmitter Power Supply 18 TD+ Transmitter Positive DATA In (PECL) 19 TD- Transmitter Negative DATA In (PECL) 9 RS1 TX Rate Select (LVTTL) Module Definition 4 SDA Two-wire Serial Data 5 SCL Two-wire Serial Clock 6 MOD_ABS Module Absent Logic “1” Input (or no connection) = Laser off Logic “0” Input = Laser on This pin is internally pulled up to VccT with a 10 kΩ resistor. These pins should be connected to signal ground on the host board. Logic “1” Output = Laser Fault (Laser off before t_fault) Logic “0” Output = Normal Operation This pin is open collector compatible, and should be pulled up to Host Vcc with a 10 kΩ resistor. This pin should be connected to a filtered +3.3 V power supply on the host board. See Application schematics on page 4 for filtering suggestions. Logic “1” Input = Light on Transmitter DATA inputs are internally AC coupled and terminated with a differential 100 Ω resistor. Logic “0” Input = Light on Transmitter DATA inputs are internally AC coupled and terminated with a differential 100 Ω resistor. This pin has an internal 30 kΩ pulldown to ground. A signal on this pin will not affect module performance. Serial ID with SFF 8472 Diagnostics. Module definition pins should be pulled up to Host Vcc with appropriate resistors for the speed and capacitive loading of the bus. See SFF8431. Serial ID with SFF 8472 Diagnostics. Module definition pins should be pulled up to Host Vcc with appropriate resistors for the speed and capacitive loading of the bus. See SFF8431. Pin should be pulled up to Host Vcc with 10 kΩ resistor. MOD_ABS is asserted “high” when the SFP+ module is physically absent from the host slot. 8.5 G SFP+ 850 NM LIMITING TRANSCEIVER, 8 GIGABIT FIBRE CHANNEL COMPLIANT 8 3.2 Absolute Maximum Ratings Parameter Symbol Ratings Unit Storage temperature Case temperature Relative humidity Transmitter differential input voltage Power supply voltage TST TC RH VD VCC -40 to +95 -40 to +90 5 – 95 (non-condensing) 2.5 0 to +4.0 ˚C ˚C % V VP-P Note: Absolute maximum ratings represent the damage threshold of the device. Damage may occur if the device is subjected to conditions beyond the limits stated here. 3.3 Operating Conditions Part Number Temperature Rating Unit PLRXPL-VC-SH4-xx-N 0 – 70 ˚C Note: Performance is not guaranteed and reliability is not implied for operation at any condition outside these limits. 8.5 G SFP+ 850 NM LIMITING TRANSCEIVER, 8 GIGABIT FIBRE CHANNEL COMPLIANT 9 3.4 Electrical Characteristics Parameter Symbol Min. Typical Max. Unit Notes Supply voltage Vcc 2.97 3.3 3.63 V All electrical and optical specifications valid within this range Power consumption Data rate Transmitter Supply current Common mode voltage tolerance Data input deterministic jitter Pdiss 480 8.5 1000 9.0 mW Gbps 110 Data input total jitter Input data dependent pulse width shrinkage Eye mask TJ DDPWS 0.31 0.11 mA mVrms UI(p-p) JSAT pattern. ∆T, BER < 1x10-12, at 8.5 Gbps (Note 1) UI JSAT pattern. ∆T, at 8.5 Gbps (Note 1) UI (p-p) JSAT pattern. ∆T, at 8.5 Gbps (Note 1) X1 X2 Y1 Y2 VIH VIL 0.155 0.5 Transmit disable voltage level IccT ∆V DJ 30 0.17 VOH VOL Transmit fault assert and reset times TFault TReset 10 2 µs ms Vcc 0.4 V V 100 µs µs 90 2.0 -0.3 Transmit disable/enable assert time TTD TTEN Transmit fault output voltage level 350 Vcc + 0.3 0.8 UI UI mV mV V V Vcc - 0.4 -0.3 10 BER < 1x10-12 Reference FC-PI-4 Revision 7.1, Figure 45 Laser output disabled after TTD if input level is VIH; Laser output enabled after TTEN if input level is VIL Laser output disabled after TTD if input level is VIH; Laser output enabled after TTEN if input level is VIL Transmit fault level is VOH and Laser output disabled TFault after laser fault. VOL is measured at 0.7 mA. Transmitter fault is VOL and Laser output restored TINI after transmitter disable is asserted for TReset, then disabled. After hot plug or Vcc ≥ 2.97 V Initialization time Receiver Supply current Output common mode voltage Data output deterministic jitter Total jitter TINI 300 ms ICCR DJ TJ 120 30 0.42 0.71 Data dependent pulse width shrinkage Eye mask DDPWS 0.36 mA mVrms RLOAD = 25 Ω, differential UI(p-p) JSAT pattern. ∆R, at 8.5 Gbps (Note 1, 4) UI(p-p) JSAT pattern. ∆R, BER < 1x10-12, at 8.5 Gbps (Note 1, 4) UI (p-p) JSAT pattern. ∆R, at 8.5 Gbps (Note 1, 4) UI Reference FC-PI-4 Revision 7.1, mV Figure 46 mV V LOS output level VOL TLOSD after light input > LOSD (Note 2) V LOS output level VOH TLOSA after light input < LOSA (Note 2) µs LOS output level VOL TLOSD after light input > LOSD (Note 2) µs LOS output level VOH TLOSA after light input < LOSA (Note 2) Loss of signal voltage level Loss of signal assert/deassert time X1 Y1 Y2 VOH 0.355 Vcc -0.5 425 Vcc +0.3 VOL -0.3 0.4 200 TLOSA 100 TLOSD 100 8.5 G SFP+ 850 NM LIMITING TRANSCEIVER, 8 GIGABIT FIBRE CHANNEL COMPLIANT 10 3.5 Optical Characteristics Parameter Transmitter Wavelength RMS spectral width Transmitter waveform dispersion penalty Average optical power Optical modulation amplitude Relative intensity noise Receiver Wavelength Maximum input power Sensitivity (OMA) Stressed sensitivity (OMA) Loss of signal assert/deassert level Low frequency cutoff Symbol Min. Typical Max. Unit Notes λp 840 850 860 0.45 4.2 nm nm dB (Note 3) Note 6 dBm µW dB/Hz 12 dB reflection nm dBm µWP-P µWP-P dBm dBm MHz (Note 7) (Note 4) Chatter-free operation; LOSD is OMA, LOSA is average power -3 dB, P<-16 dBm TWDP PAVG OMA RIN12OMA -8.2 302 λ Pmax S VECP = 3.1 dB LOSD LOSA FC 840 0 -128 850 860 76 151 -14 -30 0.3 8.5 G SFP+ 850 NM LIMITING TRANSCEIVER, 8 GIGABIT FIBRE CHANNEL COMPLIANT 11 3.6 Link Length Data Rate Standard Fiber Type Modal Bandwidth at 850 nm (MHz*km) Distance Range (m) Notes 8.5 GBd 62.5/125 µm MMF 50/125 µm MMF 50/125 µm MMF 50/125 µm MMF 50/125 µm MMF 200 500 900 1500 2000 0.5 – 21 0.5 – 50 0.5 – 90 0.5 – 120 0.5 – 150 5 5 5 5 5 Specifi cation Notes 1. UI (unit interval): one UI is equal to one bit period. For example, 8.5 Gbps corresponds to a UI of 117.65 ps. 2. For LOSA and LOSD definitions, see Loss of Signal Assert/Deassert Level in Optical Characteristics. 3. Transmitter waveform and dispersion penalty is measured using the methods specified in FC-PI-4 with a 1,0 equalizer and a 9.84-GHz, 3-dB optical bandwidth Gaussian filter for the fiber simulation. 4. Measured with stressed eye pattern as per FC-PI-4. 5. Distances, shown in the “Link Length” table, are calculated for worst-case fiber and transceiver characteristics based on the optical and electrical specifications shown in this document using techniques specified in IEEE 802.3. These distances are consistent with those specified for FC-PI-4. In most cases, longer distances are achievable. 6. The maximum transmitter output power is the lesser of the Class 1 laser eye safety limit and the maximum receiver input power limit. 7. Sensitivity is for informational purposes only. 8.5 G SFP+ 850 NM LIMITING TRANSCEIVER, 8 GIGABIT FIBRE CHANNEL COMPLIANT 12 3.7 Regulatory Compliance The PLRXPL-VC-SH4-xx-N optical transceiver complies with international Electromagnetic Compatibility (EMC) and international safety requirements and standards. EMC performance is dependent on the overall system design. Information included herein is intended as a figure of merit for designers to use as a basis for design decisions. The PLRXPL-VC-SH4-xx-N optical transceiver is lead-free and RoHS-compliant per Directive 2002/95/EC of the European Parliament and of the Council of 27 January 2003 on the restriction of the use of certain hazardous substances in electrical and electronic equipment. Regulatory Compliance Feature Test Method Performance Component safety UL 60950 UL 94, V0 IEC 60950 Directive 2002/95/EC UL File E209897 RoHS-compliant Laser eye safety1 Electromagnetic Compatibility Electromagnetic emissions EN 60825 U. S. 21CFR 1040.10 ESD immunity EMC Directive 89/336/EEC FCC CFR47 Part 15 IEC/CISPR 22 AS/NZS CISPR22 EN 55022 ICES-003, Issue 4 VCCI-03 EMC Directive 89/336/EEC IEC/CISPR/24 EN 55024 EN 61000-4-2 Radiated immunity EN 61000-4-3 Electromagnetic immunity 1. For further details, see Eye Safety TUV Report/Certificate (CB scheme) Compliant per the Directive 2002/95/EC of the European Parliament and of the Council of 27 January 2003 on the restriction of the use of certain hazardous substances in electrical and electronic equipment. TUV Certificate CDRH compliant and Class 1 laser eye safe Noise frequency range: 30 MHz to 40 GHz. Good system EMI design practice required to achieve Class B margins. Exceeds requirements. Withstand discharges of 4 kV contact and 8 kV air discharge to Criterion A, and 8 kV contact and 25 kV air discharge to Criterion B. Exceeds requirements. Field strength of 10 V/m RMS, from 10 MHz to 1 GHz. No effect on transmitter/receiver performance is detectable between these limits. 8.5 G SFP+ 850 NM LIMITING TRANSCEIVER, 8 GIGABIT FIBRE CHANNEL COMPLIANT 13 3.8 PCB Layout Figure 4 Board layout ALL DIMENSIONS ARE IN MILLIMETERS Figure 5 Detail layout 8.5 G SFP+ 850 NM LIMITING TRANSCEIVER, 8 GIGABIT FIBRE CHANNEL COMPLIANT 14 3.9 Front Panel Opening Figure 6 3.10 Module Outline ALL DIMENSIONS ARE IN MILLIMETERS Figure 7 8.5 G SFP+ 850 NM LIMITING TRANSCEIVER, 8 GIGABIT FIBRE CHANNEL COMPLIANT 15 3.11 Transceiver Belly-to-belly Mounting Figure 8 8.5 G SFP+ 850 NM LIMITING TRANSCEIVER, 8 GIGABIT FIBRE CHANNEL COMPLIANT 16 Section 4 Related Information Other information related to the SFP+ optical transceiver includes: • Section 4.1 • Section 4.2 • Section 4.3 • Section 4.4 4.1 Digital diagnostic monitoring and serial ID operation Package and handling instructions ESD discharge (ESD) Eye safety Digital Diagnostic Monitoring and Serial ID Operation The PLRXPL-VC-SH4-xx-N optical transceiver is equipped with a two-wire serial EEPROM that is used to store specific information about the type and identification of the transceiver as well as real-time digitized information relating to the transceiver’s performance. See the Small Form Factor Committee document number SFF-8472 Revision 10.3, dated December 1, 2007 for memory/address organization of the identification data and digital diagnostic data. The enhanced digital diagnostics feature monitors five key transceiver parameters which are internally calibrated and should be read as absolute values and interpreted as follows: Transceiver Temperature in degrees Celsius: Internally measured. Represented as a 16 bit signed two’s complement value in increments of 1/256°C from -40 to +70°C with LSB equal to 1/256°C. Accuracy is ± 3°C over the specified operating temperature and voltage range. Vcc/Supply Voltage in Volts: Internally measured. Represented as a 16-bit unsigned integer with the voltage defined as the full 16-bit value(0 – 65535) with LSB equal to 100 uV with a measurement range of 0 to +6.55 V. Accuracy is ± three percent of nominal value over the specified operating temperature and voltage ranges. TX Bias Current in mA: Represented as a 16-bit unsigned integer with current de- fined as the full 16-bit value (0 – 65535) with LSB equal to 2 uA with a measurement range of 0 – 131 mA. Accuracy is ± 10 percent of nominal value over the specified operating temperature and voltage ranges. TX Output Power in mW: Represented as a 16-bit unsigned integer with the power defined as the full 16-bit value (0 – 65535) with LSB equal to 0.1 uW. Accuracy is ± 2 dB over the specified temperature and voltage ranges over the range of -10 dBm to 0 dBm. Data is not valid when transmitter is disabled. RX Received Optical Power in mW: Represented as average power as a 16-bit un- signed integer with the power defined as the full 16-bit value (0 – 65535) with LSB equal to 0.1 uW. Accuracy is ± 3 dB over the specified temperature and voltage ranges over the power range of -14 dBm to 0 dBm. 8.5 G SFP+ 850 NM LIMITING TRANSCEIVER, 8 GIGABIT FIBRE CHANNEL COMPLIANT 17 Reading the data The information is accessed through the SCL and SDA connector pins of the module. The SFF-8431 Revision 2.2 specification contains all the timing and addressing information required for accessing the data in the EEPROM. The device address used to read the Serial ID data is 1010000X(A0h), and the address to read the diagnostic data is 1010001X(A2h). Any other device addresses will be ignored. MOD_ABS, pin 6 on the transceiver, is connected to Logic 0 (Ground) on the transceiver. SCL, pin 5 on the transceiver, is connected to the SCL pin of the EEPROM. SDA, pin 4 on the transceiver, is connected to the SDA pin of the EEPROM. The EEPROM Write Protect pin is internally tied to ground with no external access, allowing write access to the customer-writable field (bytes 128 – 247 of address 1010001X). Note: address bytes 0 – 127 are not write protected and may cause diagnostic malfunctions if written over. Decoding the data The information stored in the EEPROM, including the organization and the digital diagnostic information, is defined in the Small Form Factor Committee document SFF-8472 Revision 10.3, dated December 1, 2007. Data Field Descriptions 0 Address( 1010000X)(A0h) Serial ID Information; Defined by SFP MSA 0 55 95 95 JDSU-Specific Information 127 119 127 Alarm and Warning Limits Reserved for External Calibration Constants Real Time Diagnostic Information JDSU-Specific Information Nonvolatile, customerwriteable, field-writeable area Reserved for SFP MSA 247 255 Address( 1010001X)(A2h) 255 JDSU-Specific Information 8.5 G SFP+ 850 NM LIMITING TRANSCEIVER, 8 GIGABIT FIBRE CHANNEL COMPLIANT 18 Serial ID Data and Map Memory Address Value Comments 0 1 2 3-10 03 04 07 0000000020400C54 11 12 13 01 55 00 14 15 16 17 18 19 20-35 36 37-39 40-55 56-59 60-61 62 63 64 00 00 05 02 00 0F JDSU 00 00019C PLRXPLVCSH4xxN 65 66 67 68-83 84-91 92 1A 00 00 SFP Transceiver SFP with Serial ID LC Connector Intermediate distance on OM3 fiber, short wave laser without OFC, 50 and 62.5 µm fiber media, Fibre Channel 8, 4, and 2 Gbps compliant 8B/10B encoded Nominal Bit rate of 8.5 Gbps Rate Identifier (for Rate-selectable modules) No rate select implemented Single-mode fiber not supported Single-mode fiber not supported 50 meters of OM2 50/125 µm multimode fiber 21 meters of OM1 62.5/125 µm multimode fiber Copper not supported 150 meters of OM3 50/125 µm multimode fiber Vendor Name (ASCII) Reserved IEEE Company ID (ASCII) Part Number (ASCII), x = part number variable Revision of part number (ASCII) Wavelength of laser in nm; 850 Unallocated Check Code; Lower 8 bits of sum from byte 0 through 62 Conventional uncooled laser, Class 1 power level, Conventional limiting receiver output Tx_Disable, Tx Fault, Loss of Signal implemented 93 F0 94 95 96-127 128-255 03 CC_EXT 0352 CC_BASE 00 68 Serial Number (ASCII) Date Code (ASCII) Diagnostic monitoring implemented, internally calibrated, Receiver Power Measurement type is Average Power Alarms and Warnings, TX_Fault and Rx_LOS monitoring implemented, TX_Disable Control, and Monitoring. SFF-8472 Revision 10.3 compliant Check Code; Lower 8 bits of sum from byte 64 through 94 JDSU-specific EEPROM Reserved for SFF-8079 8.5 G SFP+ 850 NM LIMITING TRANSCEIVER, 8 GIGABIT FIBRE CHANNEL COMPLIANT 19 Diagnostics Data Map Memory Address Value Comments 00-01 02-03 04-05 06-07 08-09 10-11 12-13 14-15 16-17 18-19 20-21 22-23 24-25 26-27 28-29 30-31 32-33 34-35 36-37 38-39 40-55 56-59 60-63 64-67 68-71 72-75 76-77 78-79 80-81 82-83 84-85 86-87 88-89 90-91 92-94 95 96 97 98 99 100 Temp High Alarm Temp Low Alarm Temp High Warning Temp Low Warning Voltage High Alarm Voltage Low Alarm Voltage High Warning Voltage Low Warning Bias High Alarm Bias Low Alarm Bias High Warning Bias Low Warning TX Power High Alarm TX Power Low Alarm TX Power High Warning TX Power Low Warning RX Power High Alarm RX Power Low Alarm RX Power High Warning RX Power Low Warning Reserved RP4 RP3 RP2 RP1 RP0 Islope Ioffset TPslope TPoffset Tslope Toffset Vslope Voffset Reserved Checksum Temperature MSB Temperature LSB Vcc MSB Vcc LSB TX Bias MSB (Note 1) MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address For future monitoring quantities External Calibration Constant External Calibration Constant External Calibration Constant External Calibration Constant External Calibration Constant External Calibration Constant External Calibration Constant External Calibration Constant External Calibration Constant External Calibration Constant External Calibration Constant External Calibration Constant External Calibration Constant Reserved Low order 8 bits of sum from 0 – 94 Internal temperature AD values Internally measured supply voltage AD values TX Bias Current AD values 8.5 G SFP+ 850 NM LIMITING TRANSCEIVER, 8 GIGABIT FIBRE CHANNEL COMPLIANT 20 Diagnostics Data Map (continued) Memory Address Value 101 102 103 104 105 106 107 108 109 110-7 110-6 TX Bias LSB (Note 1) TX Power MSB (Note 1) TX Power LSB (Note 1) RX Power MSB RX Power LSB Reserved MSB Reserved LSB Reserved MSB Reserved LSB Tx Disable State Soft Tx Disable Control 110-5 110-4 110-3 110-2 110-1 110-0 111 112-119 120-127 128-247 248-255 Reserved Rate Select State Soft Rate Select Control Tx Fault State LOS State Data Ready State Reserved Optional alarm & warning flag bits (Note 2) Vendor specific User/Customer EEPROM Vendor specific Comments Measured TX output power AD values Measured RX input power AD values For 1st future definition of digitized analog input For 2nd future definition of digitized analog input Digital State of Tx Disable Pin Writing “1” OR pulling the Tx_Disable pin will disable the laser Digital State of Rate Select Pin Writing to this bit has no effect Digital State Digital State Digital State; “1” until transceiver is ready Reserved Refer to SFF-8472 Revision 10.3 JDSU specific Field writeable EEPROM Vendor-specific control Note : 1. During Tx disable, Tx bias and Tx power will not be monitored. 2. Alarm and warning are latched. The flag registers are cleared when the system Reads AND the alarm/warning condition no longer exists. 8.5 G SFP+ 850 NM LIMITING TRANSCEIVER, 8 GIGABIT FIBRE CHANNEL COMPLIANT 21 4.2 Package and Handling Instructions This product is not compatible with any aqueous wash process. Process plug The PLRXPL-VC-SH4-xx-N optical transceiver is supplied with a process plug. This plug protects the transceiver optics during standard manufacturing processes by preventing contamination from air borne particles. Note: It is recommended that the dust cover remain in the transceiver whenever an optical fiber connector is not inserted. Recommended cleaning and degreasing chemicals JDSU recommends the use of methyl, isopropyl and isobutyl alcohols for cleaning. Do not use halogenated hydrocarbons (trichloroethane, ketones such as acetone, chloroform, ethyl acetate, MEK, methylene chloride, methylene dichloride, phenol, N-methylpyrolldone). Flammability The housing is made of cast zinc and sheet metal. 4.3 Electrostatic Discharge (ESD) Handling Normal ESD precautions are required during the handling of this module. This transceiver is shipped in ESD protective packaging. It should be removed from the packaging and handled only in an ESD protected environment utilizing standard grounded benches, floor mats, and wrist straps. Test and operation In most applications, the optical connector will protrude through the system chassis and be subjected to the same ESD environment as the system. Once properly installed in the system, this transceiver should meet and exceed common ESD testing practices and fulfill system ESD requirements. Typical of optical transceivers, this module’s receiver contains a highly sensitive optical detector and amplifier which may become temporarily saturated during an ESD strike. This could result in a short burst of bit errors. Such an event would call for the application to reacquire synchronization at the higher layers (serializer/ deserializer chip). 8.5 G SFP+ 850 NM LIMITING TRANSCEIVER, 8 GIGABIT FIBRE CHANNEL COMPLIANT 4.4 Eye Safety The PLRXPL-VC-SH4-xx-N Optical Transceiver is a CLASS 1 LASER PRODUCT as defined by the international standard IEC 60825-1 Second Edition 2007-03 and by U.S.A. regulations for Class 1 products per CDRH 21 CFR 1040.10 and 1040.11. Laser emissions from Class 1 laser products are not considered hazardous when operated according to product specifications. Operating the product with a power supply voltage exceeding 4.0 volts may compromise the reliability of the product, and could result in laser emissions exceeding Class 1 limits. Caution Tampering with this laser based product or operating this product outside the limits of this specification may be considered an act of “manufacturing,” and will require, under law, recertification of the modified product with the U.S. Food and Drug Administration (21 CFR 1040). The use of optical instruments with this product will increase eye hazard. Ordering Information For more information on this or other products and their availability, please contact your local JDSU account manager or JDSU directly at 1-800-498-JDSU (5378) in North America and +800-5378-JDSU worldwide, or via e-mail at [email protected]. Sample: PLRXPL-VC-SH4-21-N Part Number PLRXPL-VC-SH4-21-N PLRXPL-VC-SH4-22-N Product Description 8 G SFP+ SW, limiting electrical interface, 0 – 70˚C, ± 10% Vcc, no rate select, generic, first generation 8 G SFP+ SW, limiting electrical interface, 0 – 70˚C, ± 10% Vcc, no rate select, generic, second generation NORTH AMERICA: 800 498-JDSU (5378) WORLDWIDE: +800 5378-JDSU WEBSITE: www.jdsu.com Product specifications and descriptions in this document subject to change without notice. © 2008 JDS Uniphase Corporation 30149341 501 1008 PLRXPL-VX-SH4-XX-N.DS.CMS.AE October 2008