LOW-POWER HEX TTL-TO-PECL TRANSLATOR Micrel, Inc. FEATURES ■ ■ ■ ■ SY100S391 SY100S391 DESCRIPTION The SY100S391 is a hex TTL-to-PECL translator for converting TTL logic levels to 100K logic levels. The unique feature of this translator is the ability to do this translation using only one +5V supply. The differential outputs allow each circuit to be used as an inverting/non-inverting translator, or as a differential line driver. A common enable (E), when LOW, holds all inverting outputs HIGH and all non-inverting inputs LOW. The SY100S391 is ideal for those mixed PECL/TTL applications which only have a +5V supply available. When used in the differential mode, the S391, due to its high common mode rejection, overcomes voltage gradients between the TTL and PECL ground systems. Operates from a single +5V supply Differential PECL outputs Function and pinout compatible with Fairchild F100K Available in 28-pin PLCC packages BLOCK DIAGRAM E D0 Q0 Q0 D1 Q1 Q1 D0 — D5 Data Inputs (TTL) D2 Q2 Q2 Q0 — Q5 Data Outputs (PECL) Q0 — Q5 Inverting Data Outputs (PECL) Q3 Q3 E Enable Input (TTL) D3 VCCA VCCO for ECL Outputs D4 Q4 Q4 D5 Q5 Q5 M9999-042307 [email protected] or (408) 955-1690 PIN NAMES Pin Function Rev.: I 1 Amendment: /0 Issue Date: April 2007 SY100S391 Micrel, Inc. Q1 Q1 Ordering Information Q0 D0 Q0 GNDS D1 PACKAGE/ORDERING INFORMATION Part Number Package Type Operating Range Package Marking Lead Finish Q2 SY100S391JC J28-1 Commercial SY100S391JC Sn-Pb Q2 VCCA SY100S391JCTR(1) J28-1 Commercial SY100S391JC Sn-Pb VCC VCC SY100S391JZ(2) J28-1 Commercial SY100S391JZ with Pb-Free bar-line indicator Matte-Sn SY100S391JZTR(1, 2) J28-1 Commercial SY100S391JZ with Pb-Free bar-line indicator Matte-Sn 11 10 9 8 7 6 5 D2 GND TTL 12 13 14 15 16 17 18 GND PECL GNDS GND PECL E D3 4 3 Top View PLCC J28-1 2 1 28 27 26 Q3 Q3 Notes: Q5 Q4 Q4 D5 Q5 GNDS D4 19 20 21 22 23 24 25 1. Tape and Reel. 2. Pb-Free package is recommended for new designs. 28-Pin PLCC (J28-1) LOGIC SYMBOL TRUTH TABLE Inputs Outputs Dn E Qn Qn H H H L L H L H H L L H L L L H E Note: 1. H = High Voltage Level, L = Low Voltage Level M9999-042307 [email protected] or (408) 955-1690 2 D0 D1 D2 D3 Q 0 Q0 Q1 Q1 Q 2 Q2 Q3 Q3 D4 D5 Q4 Q4 Q5 Q5 SY100S391 Micrel, Inc. GUARANTEED OPERATING CONDITIONS(1) ABSOLUTE MAXIMUM RATINGS(1) Symbol Rating Value Symbol Unit — TTL Input Voltage (2) –0.5 to +7.0 V — TTL Input Current(2) –30 to +5.0 V — PECL Output Current (DC Output HIGH) –50 V Rating Value Unit TA Operating Temperature Commercial 0 to +85 ˚C VCC Supply Voltage +4.5 to +5.5 V Note: 1. Do not exceed. — VCC Pin Potential to Ground Pin –0.5 to +7.0 V Tstore Storage Temperature –65 to +150 ˚C TJ Max. Junction Temp. Ceramic Plastic +175 +150 ˚C Notes: 1. Permanent device damage may occur if absolute maximum ratings are exceeded. This is a stress rating only and functional operation is not implied at conditions other than those detailed in the operational sections of this data sheet. Exposure to absolute maximum ratlng conditions for extended periods may affect device reliability. 2. Either voltage limit or current limit is siffucient to protect inputs. TTL-TO-PECL DC ELECTRICAL CHARACTERISTICS(1) VCC = +5.0V ± 10%; GND = 0V Symbol Parameter Min. Typ. Max. Unit VCC –1025 VCC –955 VCC –870 mV Condition VOH Output HIGH Voltage VOL Output LOW Voltage VCC –1890 VCC –1705 VCC –1620 VOHC Output HIGH Voltage Corner Point High VCC –1035 — — mV VOLC Output LOW Voltage Corner Point Low — — VCC –1610 mV VIH Input HIGH Voltage 2.0 — 5.0 V VIL Input LOW Voltage 0 — 0.8 V Over VTTL, VEE, TA Range IIH Input HIGH Current — — 10 µA VIN = +2.7V Breakdown Current — — 100 µA VIN = +5.5V, VCC = Max. — — –0.8 –4.2 mA VIN = +0.5V Dn E VIN = VIH (Max.) or VIL (Min.) Loading with 50Ω to VCC –2V VIN = VIH (Min.) or VIL (Max.) Loading with 50Ω to VCC –2V Over VTTL, VEE, TA Range IIL Input LOW Current VCD Input Clamp Diode Voltage — — –1.2 V IIN = –18mA ICC VCC Supply Current 25 — 69 mA Inputs Open Note: 1. The specified limits represent the "worst case" value for the parameter. Since these values normally occur at the temperature extremes, additional noise immunity and guardbanding can be achieved by decreasing the allowable system operating ranges. Conditions for testing shown in the tables are chosen to guarantee operation under "worst case" conditions. AC ELECTRICAL CHARACTERISTICS VCC = +5.0V ± 10% TA = 0°C Symbol TA = +25°C TA = +85°C Parameter Min. Max. Min. Max. Min. Max. Unit tPLH tPHL Propagation Delay Data and Enable to Output 400 1400 400 1400 400 1400 ps tTLH tTHL Transition Time 20% to 80%, 80% to 20% 350 1700 350 1700 350 1700 ps M9999-042307 [email protected] or (408) 955-1690 3 Condition SY100S391 Micrel, Inc. TIMING DIAGRAM 2.5 ± 0.3ns 2.5 ± 0.3ns 3.0V 90% 50% 10% INPUT 1.5V tPLH tPHL COMPLEMENT 50% tPLH OUTPUT tPHL 80% 50% 20% TRUE tTHL tTLH Propagation Delay and Transition Times M9999-042307 [email protected] or (408) 955-1690 4 SY100S391 Micrel, Inc. TEST CIRCUIT GNDTTL VIH 0.1µF 0.1µF L1 SCOPE CHAN A 0.1µF L2 S/H RT 50 RT 100 –4V L3 PULSE GENERATOR 0.1µF 2.5µF VCC GNDPECL M9999-042307 [email protected] or (408) 955-1690 5 PECL TERMINATOR NET SY100S391 Micrel, Inc. 28-PIN PLCC (J28-1) Rev. 03 MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 TEL + 1 (408) 944-0800 FAX + 1 (408) 474-1000 WEB USA http://www.micrel.com The information furnished by Micrel in this datasheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is at Purchaser’s own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. © 2006 Micrel, Incorporated. M9999-042307 [email protected] or (408) 955-1690 6