MITSUBISHI ICs (MONITOR) M61311SP/M61316SP 2 I C BUS CONTROLLED VIDEO PRE-AMP FOR HIGH RESOLUTION COLOR DISPLAY DESCRIPTION FEATURES PIN CONFIGURATION GND 1 32 BRIGHT R IN 2 31 ABL IN 3 30 R OUT VCC1(12V) G IN 4 SonG IN 5 GND1(12V) 6 B IN 7 GND2 8 Frequency Band Width RGB: 200MHz (M61311SP) 150MHz (M61316SP) (4Vp-p at -3dB) 80MHz OSD: Sync Sepa OUT 9 Video Det OUT 10 VCC3(5V) 11 OSD BLK IN 12 OSD R IN 13 Input OSD G IN 14 RGB: OSD: OSD BLK: Retrace BLK: Clamp Pulse: 0.7Vp-p (typical) 3.5V --- 5.0V (positive) 3.5V --- 5.0V (positive) 2.5V --- 5.0V (positive) 2.5V --- 5.0V (positive) OSD B IN 15 GND3 16 M61311SP/M61316SP M61311SP/M61316SP is Semiconductor Integrated Circuit for CRT Display Monitor. It includes OSD Blanking, OSD Mixing, Retrace Blanking, Video Detector, Sync Separator, Wide Band Amplifier, Brightness Control. Main/Sub Contrast, Video Response Adjust, Ret BLK Adjust, 4ch D/A OUT and OSD level Adjust Function can be controlled by IIC Bus. 29 VCC2(12V) 28 G OUT 27 GND4 26 B OUT 25 NC(GND) 24 D/A OUT 4 23 D/A OUT 3 22 D/A OUT 2 21 D/A OUT 1 20 SCL 19 SDA 18 Clamp Pulse IN 17 Retrace BLK IN Package : 32P4B NC:NO CONNECTION Output RGB: 5Vp-p (at Brightness less than 2VDC) OSD: 4Vp-p (at Brightness less than 2VDC) Sync OUT: 5Vp-p Video Det OUT: High = 4.2VDC , Low = 0.7VDC STRUCTURE Bipolar Silicon Monolithic IC 32 pin plastic SDIP APPLICATION CRT Display Monitor RECOMMENDED OPERATING CONDITIONS Supply Voltage Range 11.50V --- 12.50V (V3,V29) 4.75V --- 5.25V (V11) Rated Supply Voltage 12.00V (V3,V29) 5.00V (V11) MAJOR SPECIFICATION IIC Bus Controlled 3ch Video Pre-Amp with OSD Mixing Function and Retrace Blanking Function. The difference in the M61311SP/M61316SP is RGB Video Frequency Band Width. M61311SP is 200MHz, M61316SP is 150MHz in conditions RGB Output is 4Vp-p at -3dB. MITSUBISHI ELECTRIC 1 MITSUBISHI ICs (MONITOR) M61311SP/M61316SP 2 I C BUS CONTROLLED VIDEO PRE-AMP FOR HIGH RESOLUTION COLOR DISPLAY ABSOLUTE MAXIMUM RATING (Ambient temperature:25deg) Parameter Symbol Rating Unit Supply voltage (Pin3,29) Vcc12 13.0 V Supply voltage (Pin11) Vcc5 6.0 V Pd 2358 mW Ambient temperature Topr -20 --- +75 deg Storage temperature Tstg -40 --- +150 deg Recommend supply 12 Vopr12 12.0 V Recommend supply 5 Vopr5 5.0 V Voltage range 12 Vopr'12 11.5 --- 12.5 V Voltage range 5 Vopr'5 4.75 --- 5.25 V Power dissipation THERMAL DERATING (Maximum Rating) Power Dissipation Pd ( mW ) 2800 2400 2358 2000 1600 1415 1200 800 400 0 -25 0 25 50 75 100 125 150 Ambient Temperature Ta (deg) MITSUBISHI ELECTRIC 2 MITSUBISHI ELECTRIC Vcc 12V 7 6 4 3 2 SonG IN 8 5 Video Det OUT 10 B IN G IN R IN 9 Sync Sepa OUT 18 Clamp Pulse IN CP Sync Sepa Video Det CP CLAMP CP CLAMP CP CLAMP ABL IN 31 1bit sw 1bit sw 14 15 12 OSD level 7bit OSD MIX OSD B OSD MIX OSD G OSD MIX 16 B SUB CONT 8bit G SUB CONT 8bit 21 CP CP CP R SUB CONT 8bit OSD BLK IN MAIN CONTRAST 8bit MAIN CONTRAST MAIN CONTRAST MAIN CONTRAST OSD OSD OSD R G B IN IN IN 13 B SUB CONT 8bit SUB CONTRAST G SUB CONT 8bit SUB CONTRAST R SUB CONT 8bit SUB CONTRAST OSD R 23 D/A OUT 22 24 Ret BLK Adjust 4bit 1 BUS I/F RETRACE BLANKING RETRACE BLANKING RETRACE BLANKING 25 20 19 SCL SDA 11 Vcc 5V 26 B OUT 27 28 G OUT 29 Vcc 12V 30 R OUT 17 32 DAC CLAMP F/B AMP CLAMP F/B AMP CLAMP F/B AMP Retrace BLK IN BRIGHT MITSUBISHI ICs (MONITOR) M61311SP/M61316SP I C BUS CONTROLLED VIDEO PRE-AMP FOR HIGH RESOLUTION COLOR DISPLAY 2 BLOCK DIAGRAM 3 MITSUBISHI ICs (MONITOR) M61311SP/M61316SP 2 I C BUS CONTROLLED VIDEO PRE-AMP FOR HIGH RESOLUTION COLOR DISPLAY BUS CONTROL TABLE (1) Slave address: D7 D6 D5 D4 D3 D2 D1 R/W 1 0 0 0 1 0 0 0 =88H (2) Slave receiver format: Normal mode 8bit S 8bit SLAVE ADDRESS A SUB ADDRESS Auto increment mode 8bit S 8bit SLAVE ADDRESS 8bit DATA (SUB ADDRESS=0(X+1)H) A SUB ADDRESS (0XH)+10H 8bit DATA A (SUB ADDRESS=0(X+2)H) 8bit A DATA BYTE 8bit DATA A (SUB ADDRESS=0XH) A ------ A P A S:Start condition A:Acknowledge P:Stop condition (3) Sub address byte and data byte format: Function Bit Sub add Main contrast 8 00H Sub contrast R 8 01H Sub contrast G 8 02H Sub contrast B 8 03H OSD level 7 04H RE-BLK Adjust 4 05H Sharpness control 4 Sync Sepa SW 1 06H Video Det SW 1 TEST MODE 2 D/A OUT1 8 07H D/A OUT2 8 08H D/A OUT3 8 09H D/A OUT4 8 0AH D7 A07 0 A17 0 A27 0 A37 0 A67 0 A77 0 A87 0 A97 0 AA7 0 Data byte(top:byte format D6 D5 D4 A06 A05 A04 0 0 0 A16 A15 A14 0 0 0 A26 A25 A24 0 0 0 A36 A35 A34 0 0 0 A46 A45 A44 0 0 0 A64 0 A65 0 A66 0 A76 A75 A74 0 0 0 A86 A85 A84 0 0 0 A95 A94 A96 0 0 0 AA6 AA5 AA4 0 0 0 under:start condition) D3 D2 D1 A03 A02 A01 0 0 0 A12 A11 A13 0 0 0 A21 A23 A22 0 0 0 A31 A33 A32 0 0 0 A41 A43 A42 0 0 0 A51 A53 A52 0 0 0 A63 A62 A61 0 0 0 A73 A72 A71 0 0 0 A83 A82 A81 0 0 0 A93 A92 A91 0 0 0 AA3 AA2 AA1 0 0 0 D0 A00 1 A10 1 A20 1 A30 1 A40 1 A50 1 A60 1 A70 1 A80 1 A90 1 AA0 1 *) *) *) *) *) *) *) *) *) *) *) *) *) *) *)pre-data *)sub add. 06H Sync Sepa SW A64 0:Sync Sepa ON 1:Sync Sepa OFF Video Det SW A65 0:Video Det ON 1:Video Det OFF Always set up as A66 and A67 in 0. For IIC Data, please transfer in the period of Vertical. MITSUBISHI ELECTRIC 4 MITSUBISHI ICs (MONITOR) M61311SP/M61316SP 2 I C BUS CONTROLLED VIDEO PRE-AMP FOR HIGH RESOLUTION COLOR DISPLAY IIC BUS CONTROL SECTION SDA,SCL CHARACTERISTICS parameter symbol MIN MAX unit min. input LOW voltage VIL -0.5 1.5 V max. input HIGH voltage VIH 3.0 5.5 V SCL clock frequency fSCL 0 400 KHz tBUF 1.3 - uS tHD:STA 0.6 - uS The LOW period of the clock tLOW 1.3 - uS The HIGH period of the clock tHIGH 0.6 - uS Set up time for start condition (Only relevant for a repeated start condition) tSU:STA 0.6 - uS Hold time DATA tHD:DAT 0 0.9 uS Set-up time DATA tSU:DAT 100 - nS Rise time both SDA and SCL lines tR 20+0.1Cb 300 nS Fall time both SDA and SCL lines tF 20+0.1Cb 300 nS tSU:STO 0.6 - uS Time the bus must be free before a new transmission can start Hold time start condition After this period the first clock pulse is generated Set-up time for stop condition TIMING DIAGRAM tR tF tBUF VIH SDA VIL tHD:STA tSU:DAT tHD:DAT tSU:STA tSU:STO VIH SCL VIL tLOW S tHIGH S MITSUBISHI ELECTRIC P S 5 MITSUBISHI ICs (MONITOR) M61311SP/M61316SP 2 I C BUS CONTROLLED VIDEO PRE-AMP FOR HIGH RESOLUTION COLOR DISPLAY ELECTRICAL CHARACTERISTICS (VCC = 12V, 5V ; Ta = 25ºC unless otherwise specified) Input No. Symbol 1 Icc1 2 Icc2 3 Icc3 4 Vomax 5 Vimax 6 7 8 9 10 Gv Gv VC1 VC1 VC2 11 VC2 12 VC3 13 VC3 14 VSC1 15 VSC1 16 VSC2 17 VSC2 18 VSC3 19 VSC3 20 ABL1 21 ABL1 22 ABL2 23 ABL2 24 ABL3 25 26 27 28 29 30 31 ABL3 VB1 VB1 VB2 VB2 VB3 VB3 32 Tr 33 Tr 34 35 Tf Tf 36 VthCP 37 WCP parameter Test point 3 2 4 5 7 12 14 15 17 18 31 R G SonG B OSD OSD OSD OSD RET CP ABL BRT Main Sub R Sub G Sub B OSD ReBLK Sharp SonG VDET D/A Vcc IN IN IN IN BLK R IN G IN B IN BLK IN ( V ) ( V ) cont cont cont cont Adj Adj ness FF FF FF a a a a a a a a a a b 5 2 IA b a a a a a a a a a b 5 2 Output dynamic range 26,28, 30 Maximum input 26,28, 30 Maximum gain 26,28, 30 - Main contrast control characteristics 1 (MAX) Main contrast control relative characteristics 1 Main contrast control characteristics 2 (TYP) Main contrast control relative characteristics 2 Main contrast control characteristics 3 (MIN) Main contrast control relative characteristics 3 Sub contrast control characteristics 1 (MAX) Sub contrast control relative characteristics 1 Sub contrast control characteristics 2 (TYP) Sub contrast control relative characteristics 2 Sub contrast control characteristics 3 (MIN) Sub contrast control relative characteristics 3 ABL control characteristics 1 ABL control relative characteristics 1 ABL control characteristics 2 ABL control relative characteristics 2 ABL control characteristics 3 ABL control relative characteristics 3 Brightness control characteristics 1 Brightness control relative characteristics 1 Brightness control characteristics 2 Brightness control relative characteristics 2 Brightness control characteristics 3 Brightness control relative characteristics 3 Pulse characteristics 1 (4Vp-p) Relative pulse characteristics 1 (4Vp-p) Pulse characteristics 2 (4Vp-p) Relative pulse characteristics 2 (4Vp-p) Clamp pulse threshold voltage Clamp pulse minimum width 26,28, 30 26,28, 30 b b b b b b a b b b b b a b b b b b a a a a a a a b b b b b a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a b b b b b b 5 5 5 5 5 5 2 0.5 2 2 2 2 - - - - - - - - - - - - - - 26,28, 30 b b b a b a a a a a b 5 2 26,28, 30 26,28, 30 26,28, 30 26,28, 30 - b b b b - b b b b - b b b b - a a a a - b b b b - a a a a - a a a a - a a a a - a a a a - a a a a - b b b b - 5 5 5 4 - 2 2 2 2 - 26,28, 30 b b b a b a a a a a b 2 2 - - - - - - - - - - - - - - 26,28, 30 26,28, 30 26,28, 30 26,28, 30 - b b b b - b a a a - b a a a - a a a a - b a a a - a a a a - a a a a - a a a a - a a a a - a a a a - b b b b - 0 5 5 5 - 2 4 2 0.5 - 26,28, 30 b b b a b a a a a a b 5 2 - - - - - - - - - - - - - - 26,28, 30 26,28, 30 26,28, 30 07H 08H 09H 0AH 12V IB Relative maximum gain Limits 32 00H 01H 02H 03H 04H 05H 06H 5V Circuit current 1 power save mode 12V Circuit current 2 normal mode 5V Circuit current 3 normal mode IB Bus CTL (H) CTL Vol. 13 b b b b a a b a a a a a b a a a a a a a a a a a a a a a a a b b b 5 5 5 2 2 2 FF 00 00 08 255 255 255 255 0 0 8 FF FF 00 00 08 255 255 255 255 FF 0 0 8 FF 00 00 08 FF FF FF FF 255 255 255 255 0 0 8 FF 00 00 08 FF FF FF 255 255 255 255 0 0 8 46 FF 00 00 08 70 255 255 255 0 0 8 FF FF 00 00 08 FF FF FF FF 255 255 255 255 0 0 8 FF 00 00 08 FF FF FF 255 255 255 255 0 0 8 C8 00 00 08 FF FF FF 200 255 255 255 0 0 8 C8 00 00 08 FF FF FF 200 255 255 255 0 0 8 80 00 00 08 FF FF FF 128 255 255 255 0 0 8 80 FF 00 00 08 128 255 255 255 0 0 8 10 FF FF 00 00 08 16 255 255 255 0 0 8 10 FF 00 00 08 16 255 255 255 0 0 8 FF C8 00 00 08 FF FF FF FF C8 FF C8 255 200 200 200 0 0 8 FF 00 00 08 C8 C8 C8 255 200 200 200 0 0 8 FF 00 00 08 80 80 80 255 128 128 128 0 0 8 FF 00 00 08 80 80 80 255 128 128 128 0 0 8 FF 00 00 08 10 10 10 255 16 16 16 0 0 8 FF 10 10 10 00 00 08 255 16 16 16 0 0 8 FF FF FF FF 00 00 08 255 255 255 255 0 0 8 FF 00 00 08 8 FF FF FF 255 255 255 255 0 0 FF FF 00 00 08 255 255 255 255 0 0 8 FF FF FF FF FF 00 00 08 255 255 255 255 0 0 8 FF 00 00 08 FF FF FF FF 255 255 255 255 0 0 8 FF 00 00 08 FF FF FF 255 255 255 255 0 0 8 FF 00 00 08 FF FF FF 255 255 255 255 0 0 8 FF 00 00 08 FF FF FF 255 255 255 255 0 0 8 FF 00 00 08 FF FF FF 255 255 255 255 0 0 8 FF 00 00 08 FF FF FF 255 255 255 255 0 0 8 FF 00 00 08 FF FF FF 255 255 255 255 0 0 8 FF 00 00 08 8 FF FF FF 255 255 255 255 0 0 C8 FF 00 00 08 200 255 255 255 0 0 8 C8 FF FF FF FF 00 00 08 200 255 255 255 0 0 8 C8 00 00 08 FF FF FF FF 200 255 255 255 0 0 8 C8 00 00 08 FF FF FF 200 255 255 255 0 0 8 FF 00 00 08 FF FF FF 255 255 255 255 0 0 8 FF FF 00 00 08 255 255 255 255 0 0 8 FF FF SW SW 0 0 0 0 0 0 0 0 0 0 00 00 00 0 0 0 00 00 00 00 0 0 0 0 00 00 00 00 0 0 0 0 FF FF FF FF 255 255 255 255 0 0 0 0 FF FF FF FF FF FF FF FF FF 255 255 255 255 FF FF FF 255 255 255 255 FF 0 FF 255 255 255 255 FF 0 FF 255 255 255 255 FF 0 FF 255 255 255 255 FF 0 D/A 0 FF 0 D/A 00 FF 0 D/A FF FF FF 255 255 255 255 FF FF FF FF 0 0 255 255 255 255 0 0 255 255 255 255 FF FF 0 0 0 0 0 0 0 0 0 0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 255 255 255 255 FF 0 FF 255 255 255 255 FF 0 FF 255 255 255 255 FF 0 FF 255 255 255 255 FF 0 FF 255 255 255 255 FF 0 FF FF 255 255 255 255 FF 0 FF FF 255 255 255 255 FF 0 FF 255 255 255 255 FF 0 FF FF FF 255 255 255 255 FF FF FF FF 0 0 255 255 255 255 0 0 255 255 255 255 FF FF 0 0 0 0 0 0 0 0 0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 255 255 255 255 FF 0 FF 255 255 255 255 FF 0 FF 255 255 255 255 FF 0 FF 255 255 255 255 FF 0 FF FF 255 255 255 255 FF 0 FF FF 255 255 255 255 FF 0 FF 255 255 255 255 FF 0 FF FF FF 255 255 255 255 FF FF FF FF 0 0 255 255 255 255 0 0 255 255 255 255 FF FF 0 0 0 0 0 FF FF FF FF FF FF FF FF FF 255 255 255 255 FF 0 FF FF 255 255 255 255 FF 0 FF 255 255 255 255 FF 0 MIN TYP MAX Unit OUT1 OUT2 OUT3 OUT4 FF FF FF 255 255 255 255 - 6 10 mA 105 130 mA - 4 8 mA 7.5 9 - VDC 1.4 - - Vp-p 16 17.5 19 1.2 dB 0.8 1.0 - 3.3 4 0.8 1.0 1.2 2.3 2.8 3.3 Vp-p 0.8 1.0 1.2 4.7 Vp-p - - 0.25 0.55 0.85 Vp-p -0.2 0 0.2 Vp-p 3.3 4 4.7 Vp-p 0.8 1.0 1.2 2.3 2.8 3.3 Vp-p 0.8 1.0 1.2 0.2 0.5 0.8 Vp-p -0.2 0 0.2 Vp-p 3.4 4.2 5.0 Vp-p 0.8 1.0 1.2 1.5 2.0 2.5 Vp-p 0.8 1.0 1.2 -0.3 0 0.3 Vp-p -0.2 0 0.2 Vp-p 3.4 3.8 4.2 VDC -0.3 0 0.3 V 1.6 1.9 2.2 VDC -0.3 0 0.3 V 0.3 0.5 0.7 VDC -0.3 0 0.3 V - 2.2 2.7 3.0 3.5 nS - - - - -0.8 0 0.8 nS - 2.2 2.7 3.0 3.5 nS -0.8 0 0.8 nS 0.7 1.5 2.3 VDC 0.2 - - uS *) *) *) No. 32&34 Pulse characteristics 1&2 (4Vp-p) top : M61311SP under : M61316SP MITSUBISHI ELECTRIC 6 MITSUBISHI ICs (MONITOR) M61311SP/M61316SP 2 I C BUS CONTROLLED VIDEO PRE-AMP FOR HIGH RESOLUTION COLOR DISPLAY Input No. Symbol 38 39 OTr OTf 40 Oadj1 41 Oadj1 42 Oadj2 43 Oadj2 44 Oadj3 45 Oadj3 46 VthOSD 47 OBLK 48 OBLK 50 VthBLK 51 HBLK1 52 HBLK2 53 HBLK3 54 VthHBLK 55 SS-NV 56 SS-SV 57 VSH 58 VSL parameter OSD pulse characteristics 1 OSD pulse characteristics 2 OSD adjust control characteristics 1 (MAX) OSD adjust control relative characteristics 1 OSD adjust control characteristics 2 (TYP) OSD adjust control relative characteristics 2 OSD adjust control characteristics 3 (MIN) OSD adjust control relative characteristics 3 OSD input threshold voltage Black level difference in OSD BLK on/off Relative OBLK OSD BLK input threshold voltage Retrace BLK characteristics 1 Retrace BLK characteristics 2 Retrace BLK characteristics 3 Retrace BLK input threshold voltage SOG input maximum noise voltage SOG minimum input voltage Sync output high level Sync output low level 59 TDS-F Sync output delay time 1 60 TDS-R Sync output delay time 2 61 VD-NV 62 VD-SV 63 VVDH 64 VVDL V-DET input maximum noise voltage V-DET minimum input voltage V-DET output high level V-DET output low level Test point 26,28, 30 69 IA+1 70 IA+2 7 12 CTL Vol. 13 14 15 17 18 31 R G SonG B OSD OSD OSD OSD RET CP ABL BRT Main Sub R Sub G Sub B OSD ReBLK Sharp SonG VDET D/A Vcc IN IN IN IN BLK R IN G IN B IN BLK b a a a a a b b b a IN b ( V ) ( V ) cont cont cont cont Adj Adj ness FF FF FF FF 5 2 a a b b b a b 5 2 26,28, 30 b a a a a b b b b a b 5 2 - - - - - - - - - - - - - 26,28, 30 b a a a a b b b b a b 5 2 - - - - - - - - - - - - - - 26,28, 30 b a a a a b b b b a b 5 2 - - - - - - - - - - - - - - 26,28, 30 b a a a a a b b b a b 5 2 26,28, 30 b a a a a b a a a a b 5 2 26,28, 30 b a a a a b a a a a b 5 2 26,28, 30 b b b a b b a a a a b 5 2 26,28, 30 b a a a a a a a a b b 5 2 26,28, 30 b a a a a a a a a b b 5 2 26,28, 30 b a a a a a a a a b b 5 2 26,28, 30 b a a a a a a a a b b 5 2 9 b a a b a a a a a a b 5 2 9 b a a b a a a a a a b 5 2 9 b a a b a a a a a a b 5 2 9 b a a b a a a a a a b 5 2 9 b a a b a a a a a a b 5 2 9 10 10 10 10 21,22, 23,24 b a a b a a a a a a b 5 2 b b b a b a a a a a b 5 2 b b b a b a a a a a b 5 2 b b b b b b a a b b a a a a a a a a a a b b 5 5 2 2 b b b a b a a a a a b 5 2 b b b a b a a a a a b 5 2 b a a a a a a a a a b 5 2 21,22, 23,24 b a a a a a a a a a b 5 2 D/A OUT input current 1 21,22, 23,24 b a a a a a a a a a b 5 2 D/A OUT input current 2 21,22, 23,24 b a a a a a a a a a b 5 2 b a a a a a a a a a b 5 2 71 IA- D/A OUT output current 21,22, 23,24 72 DNL D/A nonlinearity 21,22, 23,24 Limits 07H 08H 09H 0AH 12V a - Bus CTL (H) 32 00H 01H 02H 03H 04H 05H 06H a 10 VDL 5 a 66 TDV-R V-DET output delay time 2 68 4 b 10 67 VDH 2 26,28, 30 65 TDV-F V-DET output delay time 1 D/A output maximum voltage D/A output minimum voltage 3 b a a a a a a a a a b 5 2 6F 00 08 255 255 255 255 111 0 8 FF 6F 00 08 255 255 255 255 111 0 8 FF FF FF FF 7F 00 08 255 255 255 255 127 0 8 FF 00 08 FF FF FF FF FF FF 7F 255 255 255 255 127 FF 0 8 FF 40 00 08 255 255 255 255 64 0 8 FF FF FF FF FF 40 00 08 255 255 255 255 64 0 8 FF 00 00 08 FF FF FF FF 255 255 255 255 0 0 8 FF FF 00 00 08 255 255 255 255 0 0 8 FF FF FF FF FF 00 00 08 255 255 255 255 0 0 8 FF 00 00 08 FF FF FF FF 255 255 255 255 0 0 8 FF FF 00 00 08 255 255 255 255 0 0 8 FF FF FF FF FF 00 00 08 255 255 255 255 0 0 8 FF 00 0F 08 FF FF FF FF 255 255 255 255 0 15 8 FF FF 00 08 08 255 255 255 255 0 8 8 FF FF FF FF FF 00 00 08 255 255 255 255 0 0 8 FF 00 00 08 FF FF FF FF 255 255 255 255 0 0 8 FF FF 00 00 08 255 255 255 255 0 0 8 FF FF FF FF FF 00 00 08 255 255 255 255 0 0 8 FF 00 00 08 FF FF FF FF 255 255 255 255 0 0 8 FF FF 00 00 08 255 255 255 255 0 0 8 FF FF FF FF FF 00 00 08 255 255 255 255 0 0 8 FF 00 00 08 FF FF FF FF 255 255 255 255 0 0 8 FF FF 00 00 08 255 255 255 255 0 0 8 FF FF FF FF FF 00 00 08 255 255 255 255 0 0 8 FF 00 00 08 FF FF FF FF 255 255 255 255 0 0 8 FF 00 00 08 8 FF FF FF 255 255 255 255 0 0 FF FF 00 00 08 255 255 255 255 0 0 8 FF FF FF FF FF 00 00 08 255 255 255 255 0 0 8 FF 00 00 08 FF FF FF FF 255 255 255 255 0 0 8 FF FF 00 00 08 255 255 255 255 0 0 8 FF FF FF FF FF 00 00 08 255 255 255 255 0 0 8 FF 00 00 08 FF FF FF FF 255 255 255 255 0 0 8 FF FF 00 00 08 255 255 255 255 0 0 8 FF FF 00 00 08 255 255 255 255 0 0 8 FF FF MITSUBISHI ELECTRIC FF FF D/A D/A D/A SW SW OUT1 OUT2 OUT3 OUT4 0 0 255 255 255 255 FF FF FF FF FF FF FF FF 0 0 255 255 255 255 0 0 255 255 255 255 FF FF 0 0 FF FF FF FF FF FF 255 255 255 255 FF FF FF FF 0 0 255 255 255 255 0 0 255 255 255 255 FF FF 0 0 FF FF FF FF FF FF 255 255 255 255 FF FF FF FF 0 0 255 255 255 255 0 0 255 255 255 255 FF FF 0 0 FF FF FF FF FF FF 255 255 255 255 FF FF FF FF 0 0 255 255 255 255 0 0 255 255 255 255 FF FF 0 0 FF FF FF FF FF FF 255 255 255 255 FF FF FF FF 0 0 255 255 255 255 0 0 255 255 255 255 FF FF 0 0 FF FF FF FF FF FF 255 255 255 255 FF FF FF FF 0 0 255 255 255 255 0 0 255 255 255 255 FF FF 0 0 FF FF FF FF FF FF 255 255 255 255 FF FF FF FF 0 0 255 255 255 255 0 0 255 255 255 255 FF FF 0 0 FF FF FF FF FF FF 255 255 255 255 FF FF FF FF 0 0 255 255 255 255 0 0 255 255 255 255 FF FF 0 0 0 FF FF FF FF FF 255 255 255 255 FF 0 FF FF FF FF 255 255 255 255 FF FF FF FF 0 0 255 255 255 255 0 0 255 255 255 255 FF FF 0 0 0 0 0 0 0 0 FF FF FF FF FF FF 255 255 255 255 00 00 00 00 0 0 0 0 00 00 00 00 0 0 0 0 00 00 00 00 0 0 0 0 FF FF FF FF MIN TYP MAX Unit - 2 5 nS - 4 7 nS 3.3 4.0 4.9 Vp-p 0.8 1.0 1.2 1.2 1.8 2.4 Vp-p 0.8 1.0 1.2 - - -0.5 -0.1 0.3 Vp-p -0.2 0 1.7 2.5 0.2 - 3.3 VDC -0.5 -0.1 0.3 VDC 0 1.7 2.5 3.3 VDC 1.6 1.9 2.2 VDC 1.0 1.3 1.6 VDC 0.3 0.6 0.9 VDC 0.7 1.5 2.3 VDC - - 0.02 Vp-p 0.2 - 4.5 4.9 5.0 VDC 0 0.4 0.7 VDC 10 30 65 nS 10 30 65 nS - - 0.2 - 3.8 4.2 5.0 VDC 0 0.7 1.1 VDC 10 23 50 nS 1 13 40 nS 4.7 5.2 5.7 VDC 0 0 0.5 VDC 0.18 - - mA 0.18 - - mA - - 0.4 mA - 1.0 LSB 0 0 255 255 255 255 0 0 Vari Vari Vari Vari -1.0 able able able able 0.2 - -0.2 - Vp-p 0.05 Vp-p - Vp-p 7 MITSUBISHI ICs (MONITOR) M61311SP/M61316SP 2 I C BUS CONTROLLED VIDEO PRE-AMP FOR HIGH RESOLUTION COLOR DISPLAY Note1) Measuring conditions are as listed in supplementary Table. Measured with a current meter at test point IB. Note2) Measuring conditions are as listed in supplementary Table. Measured with a current meter at test point IA. Note3) Measuring conditions are as listed in supplementary Table. Measured with a current meter at test point IB. Note4) It makes the amplitude of SG1 1.4p-p. Measure the DC voltage of the white level of the waveform output. The measured value is called Vomax. (VDC) Waveform output Vomax 0.5 0.0 Note5) Increase the input signal(SG1) amplitude gradually, starting from 0.7Vp-p. Measure the amplitude of the input signal when the output signal starts becoming distorted. Note6) Input SG1, and measure the amplitude output at OUT(26,28,30). The amplitude is called VOUT(26,28,30). Maximum gain GV is calculated by the equation below: GV = 20 LOG ( VOUT / 0.7 ) (dB) Note7) Relative maximum gain GV is calculated by the equation below: GV = VOUT(26) / VOUT(28) , VOUT(28) / VOUT(30) , VOUT(30) / VOUT(26) Note8) Input SG1, and measure the amplitude output at OUT(26,28,30). The amplitude is called VOUT(26,28,30). The measured value is called VC1. Note9) Relative characteristics VC1 is calculated by the equation below: VC1 = VOUT(26) / VOUT(28) , VOUT(28) / VOUT(30) , VOUT(30) / VOUT(26) Note10) Measuring condition and procedure are the same as described in Note8. Note11) Measuring condition and procedure are the same as described in Note9. Note12) Measuring condition and procedure are the same as described in Note8. Note13) Relative characteristics VC3 is calculated by the equation below: VC3 = VOUT(26) - VOUT(28) , VOUT(28) - VOUT(30) , VOUT(30) - VOUT(26) NOte14) Input SG1, and measure the amplitude output at OUT(26,28,30). The amplitude is called VOUT(26,28,30). The measured value is called VSC1. Note15) Relative characteristics VSC1 is calculated by the equation below: VSC1 = VOUT(26) / VOUT(28) , VOUT(28) / VOUT(30) , VOUT(30) / VOUT(26) Note16) Measuring condition and procedure are the same as described in Note14. Note17) Measuring condition and procedure are the same as described in Note15. Note18) Measuring condition and procedure are the same as described in Note14. Note19) Relative characteristics VSC3 is calculated by the equation below: VSC3 = VOUT(26) - VOUT(28) , VOUT(28) - VOUT(30) , VOUT(30) - VOUT(26) MITSUBISHI ELECTRIC 8 MITSUBISHI ICs (MONITOR) M61311SP/M61316SP 2 I C BUS CONTROLLED VIDEO PRE-AMP FOR HIGH RESOLUTION COLOR DISPLAY Note20) Measure the amplitude output at OUT(26,28,30). The amplitude is called VOUT(26,28,30). The measured value is ABL1. Note21) Relative characteristics ABL1 is calculated by the equation below: ABL1 = VOUT(26) / VOUT(28) , VOUT(28) / VOUT(30) , VOUT(30) / VOUT(26) Note22) Measuring condition and procedure are the same as described in Note20. Note23) Measuring condition and procedure are the same as described in Note21. Note24) Measuring condition and procedure are the same as described in Note20. Note25) Relative characteristics ABL3 is calculated by the equation below: ABL3 = VOUT(26) - VOUT(28) , VOUT(28) - VOUT(30) , VOUT(30) - VOUT(26) Note26) Measure the DC voltage at OUT(26,28,30). The amplitude is called VOUT(26,28,30). The measured value is called VB1. Note27) Relative characteristics VB1 is calculated by the equation below: VB1 = VOUT(26) - VOUT(28) , VOUT(28) - VOUT(30) , VOUT(30) - VOUT(26) Note28) Measuring condition and procedure are the same as described in Note26. Note29) Measuring condition and procedure are the same as described in Note27. Note30) Measuring condition and procedure are the same as described in Note26. Note31) Measuring condition and procedure are the same as described in Note27. Note32) Measure the time needed for the input pulse to rise from 10% to 90% (Tr1) and for the output pulse to rise from 10% to 90% (Tr2) with an active probe. Pulse characteristics Tr is calculated by the equations below: (Tr2)2 - (Tr1)2 (nS) Tr = Note33) Relative characteristics Tr is calculated by the equation below: Tr = Tr(26) - Tr(28) , Tr(28) - Tr(30) , Tr(30) - Tr(26) Note34) Measure the time needed for the input pulse to fall from 90% to 10% (Tf1) and for the output pulse to fall from 90% to 10% (Tf2) with an active probe. Pulse characteristics Tf is calculated by the equations below: Tf = (Tf2)2 - (Tf1)2 (nS) Note35) Relative characteristics Tf is calculated by the equation below: Tf = Tf(26) - Tf(28) , Tf(28) - Tf(30) , Tf(30) - Tf(26) 100% 90% 10% 0% Tr1 or Tr2 Tf1 or Tf2 MITSUBISHI ELECTRIC 9 MITSUBISHI ICs (MONITOR) M61311SP/M61316SP 2 I C BUS CONTROLLED VIDEO PRE-AMP FOR HIGH RESOLUTION COLOR DISPLAY Note36) Decrease the SG5 input level gradually from 5.0Vp-p, monitoring the waveform output. Measure the top level of input pulse when the output pedestal voltage turn decrease with unstable. And increase the SG5 input level gradually from 0Vp-p. Measure the top level of input pulse when the output pedestal voltage turn increase with stable (a point of 2.0V). The measured value is called VthCP. Note37) Decrease the SG5 pulse width gradually from 0.5uS, monitoring the output. Measure the SG5 pulse width when the output pedestal voltage turn decrease with unstable. And increase the SG5 pulse width gradually from 0uS. Measure the SG5 pulse width when the output pedestal voltage turn increase with stable (a point of 2.0V). The measured value is called WCP. Note38) Measure the time needed for the output pulse to rise from 10% to 90% (OTr) with an active probe. Note39) Measure the time needed for the output pulse to fall from 90% to 10% (OTf) with an active probe. Note40) Measure the amplitude output at OUT(26,28,30). The amplitude is called VOUT(26,28,30). The measured value is called Oadj1. Note41) Relative characteristics Oadj1 is calculated by the equation below: Oadj1 = VOUT(26) / VOUT(28) , VOUT(28) / VOUT(30) , VOUT(30) / VOUT(26) Note42) Measuring condition and procedure are the same as described in Note40. Note43) Measuring condition and procedure are the same as described in Note41. Note44) Measuring condition and procedure are the same as described in Note40. Note45) Relative characteristics Oadj3 is calculated by the equation below: Oadj3 = VOUT(26) - VOUT(28) , VOUT(28) - VOUT(30) , VOUT(30) - VOUT(26) Note46) Decrease the SG6 input level gradually from 5.0Vp-p, monitoring the output. Measure the top level of SG6 when the output is disappeared. And increase the SG6 input level gradually from 0Vp-p. Measure the top level of SG6 when the output is appeared. The measured value is called VthOSD. Note47) Calculating the black level voltage minus the output voltage of high section of SG6 it makes VOUT(26,28,30). The calculated value is called OBLK. Note48) Relative characteristics OBLK is calculated by the equation below: OBLK = VOUT(26) - VOUT(28) , VOUT(28) - VOUT(30) , VOUT(30) - VOUT(26) Note50) Confirm that output signal is being blanked by the SG6 at the time. Decrease the SG6 input level gradually from 5.0Vp-p, monitoring the output. Measure the top level of SG6 when the blanking period is disappeared. And increase the SG6 input level gradually from 0Vp-p. Measure the top level of SG6 when the blanking period is appeared. The measured value is called VthBLK. Note51) Measure the bottom voltage at amplitude of OUT(26,28,30). The measured value is called HBLK1. Note52) Measuring condition and procedure are the same as described in Note51. Note53) Measuring condition and procedure are the same as described in Note51. Note54) Decrease the SG7 input level gradually from 5.0Vp-p, monitoring the output. Measure the top level of SG7 when the output is disappeared. And increase the SG7 input level gradually from 0Vp-p. Measure the top level of SG7 when the output is appeared. The measured value is called VthHBLK. MITSUBISHI ELECTRIC 10 MITSUBISHI ICs (MONITOR) M61311SP/M61316SP 2 I C BUS CONTROLLED VIDEO PRE-AMP FOR HIGH RESOLUTION COLOR DISPLAY Note55) When SG4 is all black (no video), the sync's amplitude of SG4 gradually from 0Vp-p to 0.02Vp-p. No pulse output permitted. Note56) When SG4 is all white or all black, the sync's amplitude of SG4 gradually from 0.2Vp-p to 0.3Vp-p. Positive pulse has occurred to Sync Sepa OUT. Note57) Measure the high voltage at Sync Sepa OUT. The measured value is treated as VSH. Note58) Measure the low voltage at Sync Sepa OUT. The measured value is treated as VSL. Note59) Sync Sepa OUT becomes high with sink part of SG4. Measure the time needed for the front edge of SG4 Sync to fall from 50% and for SyncOUT to rise from 50% with an active probe. The measured value is called TDS-F. Note60) Sync Sepa OUT becomes high with sink part of SG4. Measure the time needed for the rear edge of SG4 Sync to rise from 50% and for SyncOUT to fall from 50% with an active probe. The measured value is called TDS-R. SG4 Pedestal voltage Sync(50%) Sync Sepa OUT TDS-F (50%) TDS-R Note61) Increase the SG1 input level gradually from 0Vp-p to 0.05Vp-p. No pulse Video Det OUT permitted. Note62) Decrease the SG1 input level gradually from 0.2p-p to 0.3Vp-p. Positive pulse has occurred to Video Det OUT. Note63) Measure the high voltage at Video Det OUT. The measured value is treated as VVDH. Note64) Measure the low voltage at Video Det OUT. The measured value is treated as VVDL. Note65) Video Det OUT becomes high with signal part of SG1. Measure the time needed for the SG1 to fall from 50% and for Video Det OUT to fall from 50% with an active probe. The measured value is called TDV-F. Note66) Video Det OUT becomes high with signal part of SG1. Measure the time needed for the SG1 to rise from 50% and for Video Det OUT to rise from 50% with an active probe. The measured value is called TDV-R. SG1 Video(50%) (50%) Pedestal voltage Video Det OUT TDV-R TDV-F MITSUBISHI ELECTRIC 11 MITSUBISHI ICs (MONITOR) M61311SP/M61316SP 2 I C BUS CONTROLLED VIDEO PRE-AMP FOR HIGH RESOLUTION COLOR DISPLAY Note68) Measure the DC voltage at D/A OUT. The measured value is called VDL. Note69) Measure the input current that flows into D/A OUT through 1Kohm by 2VDC. Note70) Measure the input current that flows into D/A OUT through 1Kohm by 0.5VDC. Note71) Measure the output current that flows out of D/A OUT through 1Kohm by 4.2VDC. A 1Kohm D/A OUT Note72) The difference of differential non-linearity of D/A OUT must be less than ±1.0LSB. MITSUBISHI ELECTRIC 12 MITSUBISHI ICs (MONITOR) M61311SP/M61316SP 2 I C BUS CONTROLLED VIDEO PRE-AMP FOR HIGH RESOLUTION COLOR DISPLAY SG No. Input signal 33uS SG1 Pulse with amplitude of 0.7Vp-p. (f=30KHz) Video width 25uS. (75%) (amplitude is variable) 8uS Video signal (all white) 0.7Vp-p Video width 25uS. (75%) All white or all black variable. SG4 0.7Vp-p Video Signal (all white, all black) Sync's amplitude is variable. 3uS 0.3Vp-p 0.5uS Pulse width and amplitude are variable. SG5 5VTTL Clamp pulse Amplitude is variable. SG6 5VTTL OSD pulse 10uS Amplitude is variable. SG7 5VTTL BLK pulse 5uS MITSUBISHI ELECTRIC 13 MITSUBISHI ELECTRIC IA SW3 a 12V A b 47u V32 29 1K 28 OUT(28) 27 1K 26 OUT(26) 25 1K 24 D/A OUT (24) 23 D/A OUT (23) 22 D/A OUT (22) 21 D/A OUT (21) 3 2 1 SG1 b SW4 a 3.3u 3.3u SW2 a IN(4) 4 5 SG4 SW7 a b SW5 b a IN(7) 7 b 8 10 Sync Video Sepa Det OUT OUT 9 IB 5V A 12 14 15 SG6 b OSD B IN CP IN SW15 b a OSD G IN SDA 19 18 Measure point (unless otherwise specified) * Capacitor : 0.01uF 16 GND Ret BLK IN 17 SG5 SG7 SW18 SW17 a b a b CP IN SCL SW14 b a 13 OSD R IN SCL 20 SDA SW13 b a OSD BLK IN SW12 a 11 5V 47u 50K Sync Video Sepa Det GND OUT OUT 0.01u B IN 3.3u 6 GND 0.01u 1u SonG IN G IN IN(2) 0.01u 12V R IN SonG IN ABL R OUT 12V G OUT GND B OUT GND D/A D/A D/A D/A IN OUT4 OUT3 OUT2 OUT1 30 OUT(30) GND Bright 31 0 - 5V V31 32 0 - 5V MITSUBISHI ICs (MONITOR) M61311SP/M61316SP I C BUS CONTROLLED VIDEO PRE-AMP FOR HIGH RESOLUTION COLOR DISPLAY 2 TEST CIRCUIT 14 MITSUBISHI ICs (MONITOR) M61311SP/M61316SP 2 I C BUS CONTROLLED VIDEO PRE-AMP FOR HIGH RESOLUTION COLOR DISPLAY TERMINAL DESCRIPTION No. Name Remark Peripheral Circuit of pins DC Voltage(V) 12V 2 R IN 4 G IN 7 B IN 2K 2K 3.5 CP 0.02mA 3 VCC 1 (12V) Clamp to about 3.5V due to clamp pulse from Pin18. Input at low impedance. 2.25V 3.5V Connect to the power supply that stabilized. 12 5V 30K 1.5K 5 SonG IN When open 2.3 6K 1.5K 6K 10K 5 1K 2.28V 0.13mA 0.2mA 1 6 8 16 27 GND GND 1 GND 2 GND 3 GND 4 Connect to GND. GND Sync Sepa output pin. When the rise time of the signal is sped up, connect about 2.3 Kohm between 5V power supply. When it does not use, do openly. So as not to flow into Pin9 8mA over, resistance value does not make to 2.3Kohm or under. 5V 1K 9 Sync Sepa OUT 2.4V SYNC ON VIDEO input pin. Sync is negative. Input signal at Pin5, compare with the reference voltage of internal circuit in order to separate Sync signal from Sync on Green signal. Input at low impedance. Do not input the signal without the Sync. When it does not use this function, connect to capacitor between GND, turn on Sync Sepa SW by IIC BUS. - 9 Output is a positive. 12V 10 Video Det OUT Pin10 needs to connect the 50Kohm between 5V power supply. When it does not use this function, turn off Video Det SW by IIC BUS. 10 50K 11 VCC (5V) Connect to the power supply that stabilized. 5 MITSUBISHI ELECTRIC 15 MITSUBISHI ICs (MONITOR) M61311SP/M61316SP 2 I C BUS CONTROLLED VIDEO PRE-AMP FOR HIGH RESOLUTION COLOR DISPLAY No. Name Remark Peripheral Circuit of pins DC Voltage(V) 12V 3.5 --- 5V 12 OSD BLK IN 13 OSD R IN 14 OSD G IN 15 OSD B IN Input the positive pulse. 0.1mA 1.5V --- GND 500 500 500 When it does not use this function, connect to GND. When input OSD RGB pulse, input OSD BLK pulse without fail. 500 3.25V 3.25V Input the positive pulse. 12V 2.5 --- 5V 50K 17 Retrace BLK IN 0.5V --- GND When it does not use this function, connect to GND. 17 2.25V 12V Input the positive pulse which width 200nS over. Input at low impedance. 0.15mA 750 Clamp Pulse 18 IN 750 50K 2.5 --- 5V - 0.5V --- GND 10K 10K 500 18 3.75V 12V SDA of IIC BUS. (Serial data line) Tth = 2.3V 19 SDA - 2K 19 3.0V MITSUBISHI ELECTRIC 16 MITSUBISHI ICs (MONITOR) M61311SP/M61316SP 2 I C BUS CONTROLLED VIDEO PRE-AMP FOR HIGH RESOLUTION COLOR DISPLAY No. Name Peripheral Circuit of pins DC Voltage(V) Remark 12V SCL of IIC BUS. (Serial clock line) Tth = 2.3V 20 SCL - 2K 20 3.0V 12V 21 D/A OUT 1 22 D/A OUT 2 23 D/A OUT 3 24 D/A OUT 4 26 B OUT 28 G OUT 30 R OUT 27 GND 4 D/A output pin. Output voltage ranges is 0V to 5V. Input current is below 0.18mA. Output current is below 0.4mA. 15K This terminal needs to connect the 1 to 3Kohm resister between GND. This resistance value may be changed, to improve the video output characteristics. 29 Variable 50 Connect to GND. 35 27 29 VCC 2 (12V) It is the power supply of emitter follower of RGB output exclusive use. 12 5V 6K 5K 31 ABL IN ABL (Automatic beam limitter) input pin. When open 2.5V Input voltage in the ranges of 0V to 5V. 9K 2K 16.25K 2.5K 31 0.4mA 12V Output amplitude MAX with 5V. Output amplitude MIN with 0V. When it does not use this function, connect to 5V. It is recommended that the IC is used between pedestal voltage 2V to 3V. 35K 35K 32 BRIGHT - To other channel 32 25 NC Connect to GND. - MITSUBISHI ELECTRIC 17 MITSUBISHI ICs (MONITOR) M61311SP/M61316SP 2 I C BUS CONTROLLED VIDEO PRE-AMP FOR HIGH RESOLUTION COLOR DISPLAY ELECTRICAL CHARACTERISTICS (Reference data) Main contrast control characteristics 6 Output amplitude (Vp-p) Output amplitude (Vp-p) 6 4 2 Sub contrast control characteristics 4 2 Sub contrast : MAX ABL : 5V 0 00H 0 00H FFH Brightness control characteristics 6 Output amplitude (Vp-p) Output DC voltage (VDC) 6 Main contrast control data Main contrast : MAX ABL : 5V 4 2 Sub contrast control data FFH ABL control characteristics 4 2 Main contrast : MAX Sub contrast : MAX 0 0 0.5 Brightness control voltage (VDC)4 OSD Adjust control characteristics 6 Output DC voltage (VDC) Output amplitude (Vp-p) 6 0 4 2 ABL control voltage (VDC) 5 D/A OUT control characteristics 4 2 Brightness : 2VDC 0 00H OSD adjust control data 7FH 0 00H MITSUBISHI ELECTRIC D/A OUT control data FFH 18 MITSUBISHI ICs (MONITOR) M61311SP/M61316SP 2 I C BUS CONTROLLED VIDEO PRE-AMP FOR HIGH RESOLUTION COLOR DISPLAY APPLICATION METHOD FOR M61311SP/M61316SP ABOUT CLAMP PULSE INPUT Clamp pulse needs to be always inputted. Clamp pulse width is recommended : 15KHz at 1.0 uS over 30KHz at 0.5 uS over 64KHz at 0.3 uS over The clamp pulse circuit in ordinary set is a long round about way, and beside high voltage, sometimes connect to external terminal, it is very easy affected by large surge. Therfore, the fig. shown right is recommended. 18 NOTICE OF APPLICATION Make the nearest distanse between output and pull down resister. Recommend this resister is 1to 3 Kohm. Power dissipation in 3Kohm is smaller than 1Kohm. Recommend pedestal voltage of IC output signal is 2V. As for the low level of the pulse input of OSD BLK, OSD, Clamp Pulse, Retrace BLK etc., avoid consisting the GND level or under. PIN31 connect to the voltage that stabilized, and pay attention as surge etc. does not flow into. VCC(12V,5V) connects to the power supply that stabilized, and bypass-capacitor connects near the terminal. When capacitor is connected to Pin29, it sometimes oscillates. Do not connect capacitor to Pin29. Connect to bypass-capacitance of the DC line near the terminal. Connect to the NC Pin to GND. The time(t) is from fall of 9bit of SCL to rise of Acknowledge. About the fowarding of IIC BUS, the time(t) changes with the resistance that connected outside. The next SCL does not overlap into this time(t). 5V R 20 SCL 400pF SCL t Acknowledge Acknowledge delay time characteristics (Reference data) Delay time t (uS) 16 12 8 4 0 1.0 2.0 3.0 5.0 Resistance value (Kohm) 7.0 10 MITSUBISHI ELECTRIC 19 MITSUBISHI ICs (MONITOR) M61311SP/M61316SP 2 I C BUS CONTROLLED VIDEO PRE-AMP FOR HIGH RESOLUTION COLOR DISPLAY APPLICATION EXAMPLE 110V CRT Cut Off Adj SCL SDA 5VDC 0.01u 47u GND Clamp Pulse IN 5VDC 3K 3K ABL IN 0 - 5VDC 100uH BRIGHT 2 - 3VDC 32 31 30 3K 100 29 28 27 26 25 24 0.01u 0.01u 0.01u 0.01u 23 21 22 20 GND Ret BLK IN 19 18 17 14 15 16 M61311SP/M61316SP 1 2 3 4 5 6 7 8 9 10 11 12 13 50K 3.3u 0.01u 3.3u 75 0.01u 1u 75 3.3u OSD B IN OSD G IN OSD R IN OSD BLK IN 0.01u 75 5VDC R IN 0.01u 12V G IN B IN GND Sync Video Sepa Det OUT OUT 47u 0.01u 5V 47u SonG IN "Purchase of Mitsubishi electric corporation's IIC components conveys a license under the Philips IIC Patent Rights to use these components in an IIC system, provided that the system conforms the IIC Standard Specification as defined by Philips" MITSUBISHI ELECTRIC 20 SEATING PLANE 1 32 EIAJ Package Code SDIP32-P-400-1.78 A L MITSUBISHI ELECTRIC e JEDEC Code – D b1 Weight(g) 2.2 b Lead Material Alloy 42/Cu Alloy 16 17 b2 A2 A1 A A1 A2 b b1 b2 c D E e e1 L Symbol Plastic 32pin 400mil SDIP c Dimension in Millimeters Min Nom Max – – 5.08 0.51 – – – 3.8 – 0.35 0.45 0.55 0.9 1.0 1.3 0.63 0.73 1.03 0.22 0.27 0.34 27.8 28.0 28.2 8.75 8.9 9.05 – 1.778 – – 10.16 – 3.0 – – 0° – 15° e1 32P4B MITSUBISHI ICs (MONITOR) M61311SP/M61316SP I C BUS CONTROLLED VIDEO PRE-AMP FOR HIGH RESOLUTION COLOR DISPLAY 2 DETAILED DIAGRAM OF PACKAGE OUTLINE 21 E MITSUBISHI ICs (MONITOR) M61311SP/M61316SP 2 I C BUS CONTROLLED VIDEO PRE-AMP FOR HIGH RESOLUTION COLOR DISPLAY Keep safety first in your circuit designs! lMitsubishi Electric Corporation puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or (iii) prevention against any malfunction or mishap. Notes regarding these materials lThese materials are intended as a reference to assist our customers in the selection of the Mitsubishi semiconductor product best suited to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Mitsubishi Electric Corporation or a third party. lMitsubishi Electric Corporation assumes no responsibility for any damage, or infringement of any third-party's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application examples contained in these materials. lAll information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the time of publication of these materials, and are subject to change by Mitsubishi Electric Corporation without notice due to product improvements or other reasons. It is therefore recommended that customers contact Mitsubishi Electric Corporation or an authorized Mitsubishi Semiconductor product distributor for the latest product information before purchasing a product listed herein. The information described here may contain technical inaccuracies or typographical errors. Mitsubishi Electric Corporation assumes no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors. Please also pay attention to information published by Mitsubishi Electric Corporation by various means, including the Mitsubishi Semiconductor home page (http://www.mitsubishichips.com). lWhen using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure to evaluate all information as a total system before making a final decision on the applicability of the information and products. Mitsubishi Electric Corporation assumes no responsibility for any damage, liability or other loss resulting from the information contained herein. lMitsubishi Electric Corporation semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake. Please contact Mitsubishi Electric Corporation or an authorized Mitsubishi Semiconductor product distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use. lThe prior written approval of Mitsubishi Electric Corporation is necessary to reprint or reproduce in whole or in part these materials. lIf these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination. Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited. lPlease contact Mitsubishi Electric Corporation or an authorized Mitsubishi Semiconductor product distributor for further details on these materials or the products contained therein. MITSUBISHI ELECTRIC 22