PANJIT DI104S

DI100S~DI1010S
SURFACE MOUNT GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER
VOLTAGE
50 to 1000 Volts
CURRENT
1.0 Amperes
Recongnized File #E111753
FEATURES
• Plastic material used carries Underwriters
Laboratory recognition 94V-O
406 10.3
• Low leakage
• Surge overload rating-- 30 amperes peak
• Ideal for printed circuit board
• Exceeds environmental standards of MIL-S-19500/228
• In compliance with EU RoHS 2002/95/EC directives
MECHANICAL DATA
0.098(2.5)
0.086(2.2)
• Case: Reliable low cost construction utilizing molded plastic technique
results in inexpensive product
• Terminals: Lead solderable per MIL-STD-750, Method 2026
• Polarity: Polarity symbols molded or marking on body
• Mounting Position: Any
• Weight: 0.0105 ounce, 0.3 gram
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25°C ambient temperature unless otherwise specified.Single phase, half wave, 60Hz, Resistive or inductive load.
For capacitive load, derate current by 20%
PA RA M E TE R
S YM B O L D I 1 0 0 S D I 1 0 1 S D I 1 0 2 S D I 1 0 4 S D I 1 0 6 S D I 1 0 8 S D I 1 0 1 0 S U N I T S
M a xi m um R e c ur r e nt P e a k R e ve r s e V o l t a g e
VRRM
50
100
200
400
600
800
1000
V
M a x i m u m R M S B r i d g e In p u t V o l t a g e
VRMS
35
70
140
280
420
560
700
V
M a xi m um D C B l o c k i ng V o l t a g e
VD C
50
100
200
400
600
800
1000
V
M a xi m um A ve r a g e F o r w a r d C ur r e nt TA = 4 0 O C
IF ( A V )
1 .0
A
P e a k F o r w a r d S ur g e C ur r e nt : 8 . 3 m s s i ng l e ha l f s i ne w a ve s up e r i m p o s e d o n r a t e d l o a d ( J E D E C m e t ho d )
IF S M
30
A
I2 t R a t i n g f o r f u s i n g ( t < 8 . 3 5 m s )
I2 t
3 .7 3 5
A 2S
M a xi m um F o r w a r d V o l t a g e D r o p p e r B r i d g e E l e m e nt
a t 1 .0 A
VF
1 .1
V
M a xi m um D C R e ve r s e C ur r e nt TA = 2 5 O C
a t R a t e d D C B l o c k i ng Vo l t a g e TA = 1 2 5 O C
IR
5 .0
500
μA
Ty p i c a l J u n c t i o n c a p a c i t a n c e ( N o t e 1 )
CJ
25
pF
RθJ A
RθJ L
40
15
T J ,T S T G
-5 5 to +1 5 0
Ty p i c a l t h e r m a l r e s i s t a n c e p e r l e g ( ( N o t e 2 )
O p e r a t i n g J u n s t i o n a n d S t o r a g e Te m p e r a t u r e R a n g e
O
C / W
O
C
NOTES:
1. Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts
2. Thermal resistance from junction to ambient and from junction to lead mounted on P.C.B. with 0.5 X 0.5"(13 X 13mm) copper pads
REV.0.1-MAR.16.2010
PAGE . 1
DI100S~DI1010S
3.0
2.5
2.0
1.5
1.0
0.5
0
0
50
100
150
INSTANTANEOUS FWD CUTTENT,
AMPERES
AVERAGE FORWARD OUTPUT
CURRENT, AMPERES
RATING AND CHARACTERISTIC CURVES
O
T J =25 C
Pulse Width = 200uS
O
AMBIENT TEMPERATURE, C
INSTANTANEOUS FWD VOLTAGE, VOLTS
10
O
TA = 100 C
1.0
0.1
TA= 25 O C
0.01
0
20
40
60
80
100
120
140
PERCENT OF PEAK REVERSE VOLTAGE, %
FIG.3 TYPICAL REVERSE CHARACTERISTICS
REV.0.1-MAR.16.2010
FIG.2 TYPICAL FORWARD CHARACTERISTICS
FORWARD SURGE CURRENT, AMPERES pk
(HALF SINE-WAVE)
INSTANTANEOUS REVERSE CURRENT,uA
F I G . 1 D E R AT I N G C U RV E F O R O U T P U T
RECTIFIED CURRENT
50
40
30
20
10
0
1
2
6
10
20
40
60
100
NO. OF CYCLES AT 60Hz
FIG.4 MAX NON-REPETITIVE SURGE CURRENT
PAGE . 2
DI100S~DI1010S
MOUNTING PAD LAYOUT
ORDER INFORMATION
• Packing information
T/R - 1.5K per 13" plastic Reel
LEGAL STATEMENT
Copyright PanJit International, Inc 2010
The information presented in this document is believed to be accurate and reliable. The specifications and information herein
are subject to change without notice. Pan Jit makes no warranty, representation or guarantee regarding the suitability of its
products for any particular purpose. Pan Jit products are not authorized for use in life support devices or systems. Pan Jit
does not convey any license under its patent rights or rights of others.
REV.0.1-MAR.16.2010
PAGE . 3