DI200S~DI2010S DUAL-IN-LINE GLASS PASSIVATED SINGLE-PHASE SURFACE MOUNT BRIDGE RECTIFIER 50~1000 Volts CURRENT 2.0 Amperes 0.060(1.524) 0.040(1.016) VOLTAGE FEATURES • Plastic material used carries Underwriters Laboratory recognition 94V-O 0.009(0.25) 0.335(8.51) 0.316(8.05) • Exceeds environmental standards of MIL-S-19500/228 0.011(0.28) 0.004(0.10) • Ideal for printed circuit board 0.310(7.9) 0.290(7.4) • Surge overload rating-- 50 amperes peak 0.255(6.5) 0.245(6.2) 0.406(10.3) 0.360(9.40) • Low leakage • In compliance with EU RoHS 2002/95/EC directives 0.045(1.14) 0.035(0.89) MECHANICAL DATA • Case: Reliable low cost construction utilizing molded plastic technique results in inexpensive product 0.098(2.5) 0.086(2.2) • Terminals: Lead solderable per MIL-STD-750, Method 2026 • Polarity: Polarity symbols molded or marking on body • Mounting Position: Any • Weight: 0.0115 ounce, 0.3268 gram MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified.Single phase, half wave, 60Hz, Resistive or inductive load. For capacitive load, derate current by 20% PA RA ME TE R S YMB OL D I2 0 0 S D I2 0 1 S D I2 0 2 S D I2 0 4 S D I2 0 6 S D I2 0 8 S D I2 0 1 0 S UNITS Ma xi mum Re c urre nt P e a k Re ve rs e Vo lta g e V RRM 50 100 200 400 600 800 1000 V Ma xi mum RMS B ri d g e Inp ut Vo lta g e V RMS 35 70 140 280 420 560 700 V Ma xi mum D C B lo c k i ng Vo lta g e V DC 50 100 200 400 600 800 1000 V Ma xi mum A ve ra g e F o rwa rd C urre nt T A =4 0 O C IF (AV ) 2 .0 A P e a k F o rwa rd S urg e C urre nt:8 .3 ms s i ng le ha lf s i ne -wa ve s up e ri mp o s e d o n ra te d lo a d (J E D E C me tho d ) IF S M 50 A I2 t Ra ti ng fo r fus i ng ( t<8 .3 5 ms ) I2 t 1 0 .0 A 2S Ma xi mum F o rwa rd Vo lta g e D ro p p e r B ri d g e E le me nt a t 2 .0 A VF 1 .1 V Ma xi mum D C Re ve rs e C urre ntT J =2 5 O C a t Ra te d D C B lo c k i ng Vo lta g e T J =1 2 5 O C IR 5 .0 500 μA Typ i c a l J unc ti o n c a p a c i ta nce (No te 1 ) CJ 25 pF R θJA R θJ L 40 15 T J ,T s TG -5 5 to + 1 5 0 Typ i c a l the rma l re s i s ta nce p e r le g ((No te 2 ) Op e ra ti ng Juns ti o n a nd S to ra g e Te mp e ra ture Ra ng e O C / W O C NOTES: 1. Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts 2. Thermal resistance from junction to ambient and from junction to lead mounted on P.C.B. with 0.5 X 0.5"(13 X 13mm) copper pads November 3,2010-REV.01 PAGE . 1 DI200S~DI2010S INSTANTANEOUS FORWARD CURRENT, AMPERES AVERAGE FORWARD OUTPUT CURRENT, AMPERES RATING AND CHARACTERISTIC CURVES 3.0 2.5 2.0 1.5 1.0 0.5 0 0 50 100 1.0 .1 .01 150 AMBIENT TEMPERATURE, OC 0 0.2 0.4 0.8 0.6 1.0 1.2 1.4 INSTANTANEOUS FORWARD VOLTAGE, VOLTS FIG.1 DERATING CURVE FOR OUTPUT RECTIFIED CURRENT Fig.2 TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 70 10 O TA = 100 C 1.0 0.1 TA= 25 O C 0.01 0 20 40 60 80 100 120 140 FORWARD SURGE CURRENT,AMPERES pk (HALF SINE-WAVE) INSTANTANEOUS REVERSE CURRENT,uA 10 60 50 40 30 20 10 0 1 PERCENT OF PEAK REVERSE VOLTAGE, % FIG.3 TYPICAL REVERSE CHARACTERISTICS November 3,2010-REV.01 2 5 10 20 40 60 100 NO. OF CYCLES AT 60Hz Fig.4 MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PAGE . 2