Ordering number : ENA1373C LA4815M Monolithic Linear IC Monaural Power Amplifier Overview The LA4815M incorporates a 1-channel power amplifier with a wide operating supply voltage range built into a surface-mounted package. This IC also has a mute function and requires only a few external components, making it suitable for low-cost set design. There is also a surface-mounted package type with heat sink (LA4815VH). Applications Intercoms, door phones, transceivers, radios, toys, home appliances with voice guidance, etc. Features • Built-in 1-channel power amplifier Output power 1 = 370mW typ. (VCC = 6V, RL = 8Ω, THD = 10%) Output power 2 = 620mW typ. (VCC = 6V, RL = 4Ω, THD = 10%) Output power 3 = 230mW typ. (VCC = 5V, RL = 8Ω, THD = 10%) Output power 4 = 1,000mW typ. (VCC = 12V, RL = 16Ω, THD = 10%) • Mute function • Selectable voltage gain : 2 types 26dB/40dB * Gain values between 26 and 40dB can also be set by adding external components (two resistors). • Only a few external components 4 components/total • Wide supply voltage range 4 to 13V (When using 9V or more, another package product, LA4815VH, is recommended.) Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to "standard application", intended for the use as general electronics equipment (home appliances, AV equipment, communication device, office equipment, industrial equipment etc.). The products mentioned herein shall not be intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee thereof. If you should intend to use our products for applications outside the standard applications of our customer who is considering such use and/or outside the scope of our intended standard applications, please consult with us prior to the intended use. If there is no consultation or inquiry before the intended use, our customer shall be solely responsible for the use. Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer' s products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer' s products or equipment. 72210 SY / 090209 SY / 31109 MS 20090226-S00007 / D1008 MS PC No.A1373-1/14 LA4815M Specifications Maximum Ratings at Ta = 25°C Parameter Symbol Maximum power supply voltage VCC max Allowable power dissipation Pd max Conditions Ratings * Mounted on the board Unit 15 V 0.9 W Maximum junction temperature Tj max 150 °C Operating temperature Topr -30 to +75 °C Storage temperature Tstg -40 to +150 °C * Mounted on SANYO evaluation board : Double-sided board with dimensions of 50mm × 50mm × 1.6mm (glass epoxy) Operating Conditions at Ta = 25°C Parameter Recommended power supply Symbol Conditions Ratings Unit VCC 6 V voltage Recommended load resistance RL 4 to 32 Ω Allowable operating supply VCC op 4 to 13 V voltage range * The supply voltage level to be used must be determined with due consideration given to the allowable power dissipation of the IC. Electrical Characteristics at Ta = 25°C, VCC = 6V, RL = 8Ω, fin = 1kHz Parameter Symbol Ratings Conditions min typ Unit max Quiescent current drain-1 ICCOP1 No signal 4.6 Quiescent current drain-2 ICCOP2 No signal, pin 7 = LOW 1.6 8.3 mA Maximum output power-1 POMAX1 THD = 10% 250 370 mW Maximum output power-2 POMAX2 THD = 10%, RL = 4Ω Voltage gain-1 VG1 VIN = -30dBV 23.9 25.9 27.9 dB Voltage gain-2 VG2 VIN = -40dBV, pin 1/pin8 = GND 37 39.5 42 dB Total harmonic distortion THD VIN = -30dBV 0.11 0.7 Mute attenuation MT VIN = -10dBV, pin 7 = LOW -90 -115 Output noise voltage VNOUT Rg = 620Ω, 20 to 20kHz 40 Ripple rejection ratio SVRR Rg = 620Ω, fr = 100Hz, Vr = -20dBV 44 Mute control voltage-LOW V7cntL Mute mode Mute control voltage-HIGH1 V7cntH1 Mute released, VCC = 6.5V or lower 1.8 Mute control voltage-HIGH2 V7cntH2 Mute released, VCC = 6.5V or higher 2.4 Input resistance Ri 620 mA mW % dBV 100 μVrms dB 0.3 V V V 100 kΩ No.A1373-2/14 LA4815M Package Dimensions unit : mm (typ) 3032D Pd max – Ta 5.0 5 0.63 4.4 6.4 8 4 0.15 0.35 (1.5) 1.27 1.7max 1 (0.65) Allowable power dissipation, Pd max – W 1.2 1.0 0.9 SANYO evaluation board (double-sided), 50 × 50 × 1.6mm3 (glass epoxy) 0.8 0.6 0.54 0.4 Independent IC 0.3 0.2 0 – 30 – 20 0.18 0 20 40 60 75 80 100 0.1 Ambient temperature, Ta – °C SANYO : MFP8(225mil) Evaluation board 1. Double-sided circuit board Dimensions : 50mm × 50mm × 1.6mm Top Layer(Top view) Bottom Layer(Top view) No.A1373-3/14 LA4815M Block Diagram and Sample Application Circuit VCC from CPU + + GAIN2 8 MUTE OUT VCC 7 6 5 MUTE VCC - Vbias + PreAMP Power AMP 3 4 BIAS 1 GAIN1 2 GND1 IN PGND Vin Test Circuit + 0.35V VCC S3 + S2 8 7 6 5 GAIN2 MUTE VCC OUT GAIN1 1 GND1 2 IN 3 PGND 4 VOUT S1 S11 Vin No.A1373-4/14 LA4815M Pin Functions Pin No. Pin Name Pin Voltage Description Equivalent Circuit VCC = 6V GAIN1 0.2 Gain switching pin. • 26dB mode when left open. VCC • 40dB mode when connected to ground. (Both pins 1 and 8 must be reconfigured at 122Ω BIAS 1 10kΩ 1 the same time.) 500Ω GND 2 GND1 0 3 IN 1.57 Preamplifier system ground pin. Input pin. VCC Pre-Amp + 3 100kΩ Vbias 4 PGND 0 Power amplifier ground pin. 5 OUT 2.94 Power amplifier output pin. VCC VCC 10kΩ Pre-Amp 5 GND 6 VCC 6 7 MUTE 2.3 Power supply pin. Mute control pin. VCC • Mute ON ⇒ Low VCC • Mute OFF ⇒ High 40kΩ 10kΩ 7 30kΩ 30kΩ GND 8 GAIN2 0.2 Gain switching pin. • 26dB mode when left open. VCC • 40dB mode when connected to ground. (Both pins 1 and 8 must be reconfigured at the same time.) 125Ω 10kΩ OUT 8 500Ω GND No.A1373-5/14 LA4815M Notes on Using the IC 1. Voltage gain settings (Pins 1 and 8) The voltage gain of the power amplifier is fixed by the internal resistors. • Pins 1 and 8 be left open : Approximately 26dB • Pins 1 and 8 connected to GND : Approximately 39.5dB Note that the voltage gain can be changed using two resistors. (See Fig. 1) • Voltage gain setting : According to the resistor connected between Pin 8 and Pin 2 (GND1) * Voltage gain = 20log (20 × (625 + Rvg1)/(125 + Rvg1)) • Output DC voltage setting : According to the resistor connected between Pin 1 and Pin 2 (GND1) * Rvg1 = Rvg2 must be satisfied. In addition, the voltage gain can also be lowered to approximately 20dB (when using 5V or 6V power supply) by an application such as shown in Fig. 2 below. • Voltage gain setting : According to the resistor connected between Pin 8 and Pin 5 (OUT) * Voltage gain = 20log (20 × (125 + Rvg3)/(10,125 + Rvg3)) • Output DC voltage setting : According to the resistor connected between Pin 1 and Pin 6 (VCC) * Set the resistor values so that the Pin 5 (OUT) DC voltage is approximately half the supply voltage. Example : When Rvg3 = 10kΩ, Rvg4 = 22kΩ (when VCC = 6V) However, note that using this method to greatly lower the voltage gain deteriorates the characteristics, so the voltage gain should be lowered only to approximately 20dB. In addition, when using a high supply voltage (7V or more), the clipped waveform may invert, so this voltage gain reduction method must not be used in these cases. Rvg1 Rvg3 8 GAIN2 7 6 VCC 5 OUT 8 GAIN2 LA4815M GAIN1 GND1 1 2 7 6 VCC 5 OUT LA4815M 3 GAIN1 GND1 1 2 4 Rvg2 3 4 Rvg4 Figure 1 Figure 2 2. Signal source impedance : rg The signal source impedance value rg affects the ripple rejection ratio together with input coupling capacitor Cin, so rg should be as small as possible. Therefore, when attenuating the signal at the Cin front end as shown in Fig. 4, the constants should be set in consideration of these characteristics. Using the smallest resistor Rg1 value possible is recommended. In addition, when setting the signal level, the voltage gain should be set on the LA4815M side and the input front-end should be configured using only the input coupling capacitor, Cin, as shown in Fig. 5 in order to maximize the ripple rejection ratio. Rg2 OUT Cin 3 IN ro LA4815M Cin Rg1 other IC Pre-Amp - IN 3 + 100kΩ rg Vbias Figure 4 OUT Cin 3 IN ro Figure 3 LA4815M other IC Figure 5 No.A1373-6/14 LA4815M 3. Mute control pin (Pin 7) The internal power amplifier circuit can be disabled and audio mute is turned on by controlling the voltage applied to Pin 7. Control can be performed directly using the CPU output port, but digital noise from the CPU may worsen the LA4815M noise floor. Therefore, inserting a series resistor, Rm1 (1 to 2.2kΩ) as shown in Fig. 6, is recommended. • Mute ON : Low • Mute OFF : High or open In addition, the Pin 7 DC voltage is dependent on the supply voltage, so a reverse current flows to the CPU power supply line when the Pin 7 voltage is higher than the CPU supply voltage. In these cases, connect a resistor, Rm2 (see Fig. 7) between Pin 7 and GND to lower the Pin 7 DC voltage as shown in Fig. 6. Note that when not using the mute function, Pin 7 must be left open. LA4815M VCC VDD 10kΩ 40kΩ 7 I/O port 1kΩ Rm1 30kΩ Rm2 30kΩ VSS CPU * For reverse current prevention GND Figure 6 Reverse current prevention resistor value : Rm2 (reference value) ← When V7 is set to approximately 2.5V Rm2 – VCC 1000 7 Impedance, Rm2 – kΩ 5 3 2 100 7 5 3 2 10 7 9 11 15 13 Supply voltage, VCC – V Figure 7 4. Mute control timing When performing mute control, exercise control at the timing shown in Fig. 8. During power-on : Twu = 0 to 50ms * Pins 6 and 7 can also rise simultaneously. During power-off : Twd = 100 to 200ms Pin 6 (VCC) Pin 7 (MUTE) Twu Twd Figure 8 No.A1373-7/14 LA4815M 5. Popping noise reduction during power-off The power supply line can be directly controlled ON and OFF without using the mute function. However, when using a high supply voltage, the shock noise and aftersound during power-off tends to worsen. One method of coping with this is to connect a capacitor between Pin 6 (VCC) and Pin 7 (MUTE) as shown in Fig. 9 so that the auto mute function operates during power-off. Recommended value = 1μF LA4815M 6 VCC CVCC + Cmt + 1μF 7 MUTE Figure 9 6. Input coupling capacitor (Cin) Cin is an input coupling capacitor, and is used for DC cutting. However, this capacitor is also used to improve the ripple rejection ratio, which changes according to the capacitance value (recommended value = 1μF). In addition, this capacitor also affects the transient response characteristics during power-on and when mute is canceled, so the constant should be set in consideration of these characteristics. Design reference value = approximately 0.33 to 3.3μF • Ripple rejection ratio : Increasing the capacitance value increases the rate, and reducing the value reduces the rate. • Rise response speed : Increasing the capacitance value reduces the speed, and reducing the value increases the speed. • Popping noise : Increasing the capacitance value reduces the noise, and reducing the value increases the noise. 7. Output coupling capacitor (Cout) Cout is an output coupling capacitor used for DC cutting. However, this capacitor, Cout, in combination with load impedance RL forms a high-pass filter and attenuates the low frequency signal. Take into account the cutoff frequency when determining the capacitance value. In addition, normally a chemical capacitor is used for this capacitor, but the capacitance value of chemical capacitors decreases at low temperatures, so the value should be set in accordance with this characteristic. The cutoff frequency is expressed by the following formula. fc = 1/(2π × RL × Cout) 8. Output phase compensation capacitor (Cosc) The Cosc capacitor is used to prevent output oscillation. Use a ceramic capacitor (recommended value = 0.1μF) with good high frequency characteristics, and locate this capacitor as close to the IC as possible. 9. Power supply capacitor (CVCC) The CVCC capacitor is used to suppress the ripple component of the power supply line. Normally a chemical capacitor (recommended value = 10μF) is used for this capacitor. However, chemical capacitors have poor high frequency characteristics, so when using a CPU, DSP or other IC that generates digital noise in the set, it is recommended that a power supply bypass capacitor (ceramic capacitor, recommended value = approximately 0.1μF) be added to reject high-frequency components. Locate this bypass capacitor as close to the IC as possible. No.A1373-8/14 LA4815M 10. Signal mixing methods The following methods can be used to mix a beep, key tone or other signal into the audio signal. Note that when input to Pin 8 is selected, amplification of signals input from Pin 3 changes according to impedance Z8 connected to Pin 8. 10-1. Mixing method using resistors in the Pin 3 input front end OUT2 Signal-2 Vout2 ro OUT1 Signal-1 ro Rg3 Pin 3 input impedance : Zin = 100kΩ Rg2 IN Vin Vout1 Rg1 Pre-Amp + 3 Cin 100kΩ Vbias LA4815M other IC Figure 10 10-2. Method using input to Pin 8 • First signal system (Signal-1) voltage gain : Vg1 Vg1 = 20log (Vout/Vin1) = 20log (4 × (125 + Z8) (500 + (125 × Z8/(125 + Z8)))/(25 × Z8)) * Z8 = R1 + ro • Second signal system (Signal-2) voltage gain : Vg2 Vg2 = 20log (Vout/Vin2) = 20log (10000/(125 + R1)) * fc2 = 1/(2π × Cin2 × (R1 + 125)) 8 + Cin2 OUT2 Signal-2 125Ω R1 Vin2 10kΩ OUT 5 Vout GAIN2 500Ω ro OUT1 Signal-1 Rg2 Pre-Amp Vin1 ro Rg1 3 Cin IN + 100kΩ + PWR - Amp Vbias LA4815M other IC Figure 11 11. Short-circuit between pins Turning on the power supply with some pins short-circuited may cause deterioration or breakdown. Therefore, when mounting the IC on a board, check to make sure that no short-circuit is formed between pins by solder or other foreign substances before turning on the power supply. 12. Load short circuit Leaving the IC for a long time in the condition with a load short circuit may cause deterioration or breakdown. Therefore, never short-circuit the load. 13. Maximum ratings When used under conditions near the maximum ratings, even a slight fluctuation in the conditions may cause the maximum ratings to be exceeded, possibly resulting in a breakdown or other accidents. Therefore, always provide enough margin for fluctuations in the supply voltage and other conditions, and use within a range not exceeding the maximum ratings. No.A1373-9/14 LA4815M General characteristics (1) 1 7 5 3 2 0.1 7 5 0.01 2 3 5 7 0.1 2 3 5 7 2 1 3 5 3 2 THD – PO RL = 4Ω Vg = 26dB fin = 1kHz 10 7 5 3 2 1 7 5 3 2 0.1 7 5 0.01 2 3 5 THD – f VCC = 6V RL = 8Ω PO = 100mW 3 2 B 0d VG 1 7 5 VG 3 2 =4 B 6d =2 0.1 7 5 3 2 0.01 100 2 3 5 7 1k 2 3 5 7 10k 2 3 10 7 5 5 PO max – VCC 3 1 = VG Max. output power, PO max – W Ω RL 8Ω =4 2 3 5 7 5 VG 2 3 5 40d B 6d =2 3 2 0.1 7 5 3 2 2 3 5 7 2 1k 3 5 7 10k PO max – RL VCC = 6V Vg = 26dB THD = 10% 7 R L= 6Ω 1.5 RL =1 1 0.5 5 3 2 0.1 7 5 3 2 0.01 9 12 15 2 1 3 2V C = (P 0.3 OP I CC V CC 0 0.01 = 6V 1 1 0.4 0.2 0.5 0.4 VC 0.6 1.2 0.2 (Pd) 0.1 0 2 3 5 7 0.1 2 3 5 7 Output power, PO – W 1 2 3 5 Power dissipation, Pd – W d) 0.8 0.6 Supply current, ICCOP – A Pd – PO RL = 8Ω Vg = 26dB fin = 1kHz 5 7 2 10 3 5 7 Load impeadance, RL – Ω Supply voltage, VCC – V 100 Pd – PO 0.6 RL = 4Ω Vg = 26dB fin = 1kHz 0.5 d) 0.8 C = 9V (P 0.4 VC 0.6 V 0.4 V CC =6 ) (Pd 0.3 0.2 0.1 0.2 0 0.01 Supply current, ICCOP – A 6 OP 3 IC C Max. output power, PO max – W 7 B 2 1 1 0 Power dissipation, Pd – W 5 Frequency, f – Hz Vg = 26dB THD = 10% 2 1 3 THD – f 0.01 100 2.5 1.2 2 VCC = 6V RL = 4Ω PO = 200mW Frequency, f – Hz 3 7 0.1 Output power, PO – W Total harmonic distortion, THD – % Total harmonic distortion, THD – % Output power, PO – W 10 7 5 VCC = 9V Total harmonic distortion, THD – % VCC = 1 2V 3 2 VCC = 9V 10 7 5 VCC = 6 V 3 2 VCC = 5 V Total harmonic distortion, THD – % 5 RL = 8Ω Vg = 26dB fin = 1kHz VCC = 5V VCC = 6V THD – PO 5 0 2 3 5 7 0.1 2 3 5 7 1 2 3 5 Output power, PO – W No.A1373-10/14 LA4815M General characteristics (2) 20 15 10 5 0 10 2 3 5 7100 2 3 5 7 1k 2 3 5 7 10k 2 3 5 7100k 55 50 45 40 35 10 2 3 5 7100 50 VG =2 VG = 40dB 40 35 30 25 20 0.1 2 3 5 7 2 1 3 5 7 Capacitance, Cin – μF 10 VOUT – VIN 20 Vg = 26dB RL = 8Ω fin = 1kHz 15 Output level, VOUT – dBV B 6d 45 5 7 1k 2 3 5 7 10k 2 3 5 7100k 55 50 2 3 5 7 10k 10 VG = 40dB 40 35 30 25 1 – 20 VCC = 6V 5 0 –5 – 10 – 15 – 20 VG = 26dB 45 0 VCC = 12V SVRR – Rg VCC = 6V RL = 8Ω Vr = -20dBV fr = 100Hz Cin = 1μF 2 3 5 7 10 2 3 5 7100 2 3 5 7 1k Impeadance, Rg – Ω Vmute – VIN VCC = 6V RL = 8Ω VG = 40dB VG = 26dB 55 Supply voltage ripple rejection, SVRR – dB SVRR – Cin VCC = 6V RL = 8Ω Vr = -20dBV fr = 100Hz Rg = 620Ω 2 3 Frequency, f – Hz Muting level, Vmute – dBV Supply voltage ripple rejection, SVRR – dB Frequency, f – Hz 60 =4 0d B VG = 26dB 25 60 B 30 65 VG 35 6d VG = 40dB SVRR – f VCC = 6V RL = 8Ω Rg = 620Ω Vr = -20dBV Cin = 1μF =2 Voltage gain, VG – dB 40 70 VG VCC = 6V RL = 8Ω Supply voltage ripple rejection, SVRR – dB VG – f 45 – 40 – 60 – 80 – 100 – 120 – 25 – 30 – 50 – 40 – 30 – 20 – 10 – 140 – 30 0 – 25 – 20 Input level, VIN – dBV Vmute – VCC – 110 RL = 8Ω Vg = 26dB VIN = -10dBV fin = 1kHz Muting level, Vmute – dBV Muting level, Vmute – dBV – 110 – 15 – 10 –5 0 Input level, VIN – dBV – 115 – 120 – 125 Vmute – fin VCC = 6V RL = 8Ω Vg = 26dB VIN = -10dBV – 115 – 120 – 125 – 130 – 130 4 6 8 10 12 Supply voltage, VCC – V 14 16 10 2 3 5 7 100 2 3 5 7 1k 2 3 5 7 10k 2 3 5 7100k Input frequency, fin – Hz No.A1373-11/14 LA4815M General characteristics (3) VNO – VCC 7 RL = 8Ω Rg = 620Ω DIN AUDIO ICCO – VCC RL = OPEN Rg = 0Ω 6 Supply current, ICCO – mA Noise voltage, VNO – μVrms 200 150 VG = 40dB 100 50 VG = 26dB F E-OF MUT 5 4 3 E-ON MUT 2 1 0 4 6 8 10 12 14 0 0 16 2 4 Supply voltage, VCC – V Vpin – VCC 8 2 B) 6d Pin voltage, Vpin – V n Pi 2 5( n Pi 5 B) Control voltage, V7 cont – V 7 6 6 8 10 14 12 16 Supply voltage, VCC – V 0d 4 5( n7 Pi 4 3 2 V7 cont – VCC Vg = 26dB Vin = -20dBV RL = 8Ω 1.5 1 0.5 1 0 0 2 4 6 8 10 12 14 0 4 16 6 8 Supply voltage, VCC – V 10 12 16 14 Supply voltage, VCC – V Temperature characteristics (1) 3 2 1 7 5 3 2 0.1 0.01 2 3 5 7 0.1 2 Output power, PO – W 3 5 7 1 2 10 7 5 °C Ta = 25°C °C Ta = 25°C Ta = 75°C 10 7 5 3 THD – PO VCC = 6V RL = 4Ω VG = 26dB fin =1kHz 3 Ta = -2 5 2 5 Total harmonic distortion, THD – % 3 THD – PO VCC = 6V RL = 8Ω VG = 26dB fin =1kHz Ta = 25 Total harmonic distortion, THD – % 5 2 1 7 5 3 Ta = 75°C 2 0.1 0.01 2 3 5 7 0.1 2 3 5 7 1 Output power, PO – W No.A1373-12/14 LA4815M Temperature characteristics (2) PO – Ta RL = 8Ω VG = 26dB fin = 1kHz THD = 10% 3 2 10 7 5 3 VCC = 12V 1 7 5 Output power, PO – W Output power, PO – W 10 7 5 VCC = 6V 3 2 VCC = 5V 0.1 7 5 PO – Ta RL = 4Ω VG = 26dB fin = 1kHz THD = 10% 2 VCC = 9V 1 7 5 VCC = 6V 3 2 VCC = 5V 0.1 7 5 3 2 3 0.01 – 50 0.01 – 50 2 – 25 0 25 50 75 100 – 25 Ambient temperature, Ta – °C VG – Ta 50 VG = 40dB Noise voltage, VNO – μVrms Voltage gain, VG – dB 60 VCC = 6V RL = 8Ω 40 30 VG = 26dB 20 10 0 – 50 – 25 0 25 50 75 V7 – Ta 50 100 75 100 40 30 20 10 – 25 0 25 50 V7cont – VCC 2.1 Control voltage, V7cont – V Pin 7 voltage, V7 – V 75 Ambient temperature, Ta – °C 2 1.5 1 RL = 8Ω VG = 26dB fin = 1kHz VIN = -30dBV 1.8 Ta = 1.5 Ta = -25 °C 25° C Ta = 1.2 75° C 0.9 0.6 0.5 0 – 50 0.3 – 25 0 25 50 75 100 Ambient temperature, Ta – °C 4 6 8 10 12 14 16 Supply voltage, VCC – V ICCO – VCC 7 RL = OPEN Rg = 0Ω 6 Supply current, ICCO – mA 50 VNO – Ta 0 – 50 100 VCC = 6V RL = OPEN Rg = 0Ω 2.5 25 VCC = 6V RL = 8Ω Rg = 620Ω DIN AUDIO Ambient temperature, Ta – °C 3 0 Ambient temperature, Ta – °C Ta = 75°C 5°C Ta = 2 C -25° Ta = 5 4 3 2 1 0 0 2 4 6 8 10 12 14 16 Supply voltage, VCC – V No.A1373-13/14 LA4815M Muting on and off transient characteristics VCC = 6V RL = 8Ω Cin = 1μF VCC = 6V RL = 8Ω Cin = 2.2μF 200ms/div VCC = 12V RL = 8Ω Cin = 1μF 200ms/div OUT : 200mV/div, AC OUT : 200mV/div, AC Pin 7 : 2V/div, DC Pin 7 : 2V/div, DC 200ms/div VCC = 12V RL = 8Ω Cin = 2.2μF 200ms/div OUT : 200mV/div, AC OUT : 200mV/div, AC Pin 7 : 2V/div, DC Pin 7 : 2V/div, DC SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein. SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are controlled under any of applicable local export control laws and regulations, such products may require the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written consent of SANYO Semiconductor Co.,Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO Semiconductor Co.,Ltd. product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. Upon using the technical information or products described herein, neither warranty nor license shall be granted with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's intellctual property rights which has resulted from the use of the technical information and products mentioned above. This catalog provides information as of July, 2010. Specifications and information herein are subject to change without notice. PS No.A1373-14/14