Ordering number : EN6802A Monolithic Digital IC LB1938T 1ch, Low-saturation Forward/Reverse Motor Driver Overview The LB1938T is an H-bridge motor driver that supports low-voltage drive and features low-saturation outputs in an ultraminiature slim package. The LB1938T provides forward, reverse, brake, and standby modes controlled by two input signals, and is an optimal DC motor driver for notebook personal computers, digital cameras, cell phones, and other portable equipment. Features • Ultraminiature MSOP8 package (3.0mm×4.9mm×0.93mm) • The low saturation voltage means that the voltage applied to the motor is higher and IC heat generation is reduced. This allows this IC to be used in environments with higher ambient operating temperatures. Output saturation voltage (high side + low side): VOsat = 0.15V typical (IO = 100mA) • The wide usable voltage range and the low standby mode current drain of 0.1 µA make this IC optimal for battery operated equipment. • There are no constraints on the relationship between the input signal voltage and the supply voltage. For example, this IC can be use at VCC = 3V and VIN = 5V. • Thermal protection circuit limits the drive current and prevents the IC from causing a fire or being destroyed if the IC chip temperature reaches or exceeds 180°C due to large currents flowing when the outputs are shorted due to, for example, motor layer shorting or other phenomena. Specifications Absolute Maximum Ratings at Ta = 25°C Parameter Symbol Conditions Ratings Unit Supply voltage VCC max 10.5 V Output current IOUT max 800 mA Output voltage VOUT max VCC+VSF V 10 V Input applied voltage VIH max Continued on next page. Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to "standard application", intended for the use as general electronics equipment (home appliances, AV equipment, communication device, office equipment, industrial equipment etc.). The products mentioned herein shall not be intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee thereof. If you should intend to use our products for applications outside the standard applications of our customer who is considering such use and/or outside the scope of our intended standard applications, please consult with us prior to the intended use. If there is no consultation or inquiry before the intended use, our customer shall be solely responsible for the use. Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer' s products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer' s products or equipment. 60607 MS IM / 91003 TN (OT) No.6802-1/5 LB1938T Continued from preceding page. Parameter Symbol Allowable power dissipation Pd max Conditions Ratings Unit Mounted on a specified board * 400 mW Operating temperature range Topr -30 to +85 °C Storage temperature range Tstg -55 to +150 °C Note *: Mounted on a specified board: 114.3mm×76.1mm×1.5mm, glass epoxy resin, wiring density 20% Allowable Operating Range at Ta = 25°C Parameter Symbol Conditions Ratings Unit Supply voltage VCC Input high-level voltage VIH 2.0 to 9.5 V Input low-level voltage VIL -0.3 to +0.3 V 2.2 to 10 V Electrical Characteristics at Ta = 25°C, VCC = 3V Parameter Symbol Ratings Conditions min Circuit current max ICC1 Standby 0.1 5 µA ICC2 Forward/reverse drive 14 19 mA ICC3 Output saturation voltage Unit typ VOsat1 Brake Upper+lower IO = 100mA 20 29 mA 0.15 0.2 V 0.35 0.5 V V for forward/reverse rotation VOsat2 Upper+lower IO = 300mA for forward/reverse rotation Upper IO = 100mA for braking 0.1 0.15 Spark killer diode forward voltage VOsat3 VSF IO = 300mA 0.9 1.7 V Spark killer diode inverse current IRS VOUT = 10V 0.1 5 µA Input current IIN VIN = 5V 75 98 µA Thermal protection operating TSD Design target value * °C 180 temperature Note *: Design target value: Measurement with a single unit not made. Package Dimensions unit : mm (typ) 3245B 0.65 0.125 1.1MAX (0.85) 0.25 600 500 400 Mounted on a specified board 114.3mm×76.1mm×1.5 mm, glass epoxy resin 300 208 200 100 0 -30 0 30 60 Ambient Temperature, Ta -°C 90 120 ILB01453 0.08 (0.53) 2 Allowable Power Dissipation, Pd max - mW 0.5 3.0 4.9 8 1 Pd max - Ta 700 3.0 SANYO : MSOP8(150mil) No.6802-2/5 LB1938T Pin Assignment VCC 1 8 P-GND 7 OUT1 IN2 3 6 OUT2 S-GND 4 5 NC IN1 2 LB1938T Top view MSOP8 ILB01454 S-GND: GND for the control system P-GND: GND for the power system Truth Table IN1 IN2 OUT1 OUT2 Mode L L OFF OFF Standby H L H L Forward rotation L H L H Reverse rotation H H H H Brake Sample Application Circuit C1 = 0.1 to 10µF VCC 1 60kΩ 2 CPU 60kΩ 7 M 6 3 OUT2 80kΩ IN2 OUT1 Control block 80kΩ IN1 S-GND 4 8 P-GND ILB01455 Cautions: • VCC and GND lines suffer substantial fluctuation in the current quantity, causing a problem of line oscillation in certain cases. In this case, take following points into account: (1) Use a thick and short wiring to reduce the wiring inductance. (2) Insert a capacitor with satisfactory frequency characteristics near IC. (3) Connect S-GND to the control system GND on the CPU side and P-GND to the power system GND. No.6802-3/5 LB1938T VO(sat) - IO 0.4 0.3 0.2 0.1 0 0 100 200 300 400 Output current, IO - mA VCC = 3V 0.4 IO = 3 0 0mA 0.3 0.2 IO = 100m 0.1 0 -40 500 -20 0 20 40 60 80 A 100 Ambient temperature, Ta - °C ILB01459 ICC - Tc 28 VO(sat) - Ta 0.5 VCC = 3V Output saturation voltage, VO(sat) - V Output saturation voltage, VO(sat) - V 0.5 140 ILB01458 ICC - VCC 28 24 120 VCC = VIN 24 16 Bra k VC e mode C =5 V 12 Forw a rd o 8 r reve rse m ode, V 3V CC = 5 V Current drain, ICC - mA Current drain, ICC - mA e Brake mod 20 4 20 reverse Forward or 16 mode IN1 IN2 12 8 4 3V 0 -40 0 -20 0 20 40 60 80 100 Case temperature, Tc - °C 120 140 0 2 3 4 5 6 7 8 Supply voltage, VCC - V IIN - VIN 160 1 ILB01457 9 10 ILB01460 ICC Standby Mode Temperature Characteristics 2.0 VCC = 3V VCC = 11V Current drain, ICC - µA Input current, IIN - µA 1.6 120 80 40 1.2 0.8 0.4 0.29 Under 0.01µA 0 0 1 2 3 4 5 6 7 8 Input voltage, VIN - V 9 10 ILB01461 0 -40 -20 0 20 40 60 80 Case temperature, Tc - °C 100 120 140 ILB01462 IN Pin Input Current Temperature Characteristics 100 VIN = 5V Input current, IIN - µA 80 60 40 20 0 -40 -20 0 20 40 60 80 Case temperature, Tc - °C 100 120 140 ILB01463 No.6802-4/5 LB1938T SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein. SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are controlled under any of applicable local export control laws and regulations, such products may require the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written consent of SANYO Semiconductor Co.,Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO Semiconductor Co.,Ltd. product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. Upon using the technical information or products described herein, neither warranty nor license shall be granted with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's intellctual property rights which has resulted from the use of the technical information and products mentioned above. This catalog provides information as of June, 2007. Specifications and information herein are subject to change without notice. PS No.6802-5/5