SANYO LC87F0808A

Ordering number : ENA1828
LC87F0808A
CMOS IC
8K-byte FROM and 256-byte RAM integrated
8-bit 1-chip Microcontroller
Overview
The SANYO LC87F0808A is an 8-bit microcomputer that, centered around a CPU running at a minimum bus cycle time
of 50.0ns, integrates on a single chip a number of hardware features such as 8K-byte flash ROM (On-boardprogrammable), 256-byte RAM, an On-chip-debugger, sophisticated 16-bit timers/counters (may be divided into 8-bit
timers), a 16-bit timer/counter (may be divided into 8-bit timers/counters or 8-bit PWMs), two 8-bit timers with
a prescaler, a base timer serving as a time-of-day clock, a high-speed clock counter, a synchronous SIO interface,
an asynchronous/synchronous SIO interface, a UART interface (full duplex), motor control PWM , a 10/8-bit 10-channel
AD converter, a system clock frequency divider, an internal reset and a 21-source 10-vector interrupt feature.
This microcomputer is suitable for small motor control equipment.
Features
„Flash ROM
• Capable of On-board-programming with wide range (3.3 to 5.5V) of voltage source.
• Block-erasable in 128 byte units
• Writable in 2-byte units
• 8192 × 8 bits
„RAM
• 256 × 9 bits
„Minimum Bus Cycle
• 50.0ns (20MHz at VDD=3.3V to 5.5V)
Note: The bus cycle time here refers to the ROM read speed.
* This product is licensed from Silicon Storage Technology, Inc. (USA), and manufactured and sold by
SANYO Semiconductor Co., Ltd.
Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to
"standard application", intended for the use as general electronics equipment (home appliances, AV equipment,
communication device, office equipment, industrial equipment etc.). The products mentioned herein shall not be
intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace
instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety
equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case
of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee
thereof. If you should intend to use our products for applications outside the standard applications of our
customer who is considering such use and/or outside the scope of our intended standard applications, please
consult with us prior to the intended use. If there is no consultation or inquiry before the intended use, our
customer shall be solely responsible for the use.
Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate
the performance, characteristics, and functions of the described products in the independent state, and are not
guarantees of the performance, characteristics, and functions of the described products as mounted in the
customer' s products or equipment. To verify symptoms and states that cannot be evaluated in an independent
device, the customer should always evaluate and test devices mounted in the customer' s products or
equipment.
Ver.1.00
91510HKIM 20100823-S00001 No.A1828-1/25
LC87F0808A
„Ports
• Normal withstand voltage I/O ports
Ports I/O direction can be designated in 1-bit units
Ports I/O direction can be designated in 4-bit units
• Dedicated oscillator ports/input ports
• Reset pin
• On-chip Debugger pin
• Power pins
20 (P1n, P20, P21, P30 to P35, P70 to P73)
8 (P0n)
2 (CF1/XT1, CF2/XT2)
1 (RES)
1 (OWP0)
4 (VSS1, VSS2, VDD1, VDD2)
„Timers
• Timer 0: 16-bit timer/counter with a capture register.
Mode 0: 8-bit timer with an 8-bit programmable prescaler (with an 8-bit capture register) × 2 channels
Mode 1: 8-bit timer with an 8-bit programmable prescaler (with an 8-bit capture register)
+ 8-bit counter (with an 8-bit capture register)
Mode 2: 16-bit timer with an 8-bit programmable prescaler (with a 16-bit capture register)
Mode 3: 16-bit counter (with a 16-bit capture register)
• Timer 1: 16-bit timer/counter that supports PWM/toggle outputs
Mode 0: 8-bit timer with an 8-bit prescaler (with toggle outputs) + 8-bit timer/
counter with an 8-bit prescaler (with toggle outputs)
Mode 1: 8-bit PWM with an 8-bit prescaler × 2 channels
Mode 2: 16-bit timer/counter with an 8-bit prescaler (with toggle outputs)
(toggle outputs also possible from the lower-order 8 bits)
Mode 3: 16-bit timer with an 8-bit prescaler (with toggle outputs)
(The lower-order 8 bits can be used as PWM)
• Timer 6: 8-bit timer with a 6-bit prescaler (with toggle outputs)
• Timer 7: 8-bit timer with a 6-bit prescaler (with toggle outputs)
• Base timer
1) The clock is selectable from the subclock (32.768kHz crystal oscillation), system clock, and timer 0 prescaler
output.
2) Interrupts are programmable in 5 different time schemes
3) The base timer is unavailable when the CF oscillator circuit is selected
„SIO
• SIO0: 8-bit Synchronous serial interface
1) LSB first/MSB first mode selectable
2) Built-in 8-bit baudrate generator (maximum transfer clock cycle=4/3tCYC)
• SIO1: 8-bit asynchronous/synchronous serial interface
Mode 0: Synchronous 8-bit serial I/O (2- or 3-wire configuration, 2 to 512 tCYC transfer clocks)
Mode 1: Asynchronous serial I/O (half-duplex, 8 data bits, 1 stop bit, 8 to 2048 tCYC baudrates)
Mode 2: Bus mode 1 (start bit, 8 data bits, 2 to 512 tCYC transfer clocks)
Mode 3: Bus mode 2 (start detect, 8 data bits, stop detect)
„UART
• Full Duplex
• 7/8/9 bit data bits selectable
• 1 Stop bit (2 bits in continuous data transmission)
• Built-in baudrate generator
„AD Converter: 10 bits/8 bits × 10 channels (internal: 2 channels)
• 10/8 bits AD converter resolution selectable
• Auto start function (It links an interrupt factor of MCPWM)
No.A1828-2/25
LC87F0808A
„Remote Control Receiver Circuit (sharing pins with P73, INT3, and T0IN)
• Noise rejection function (noise filter time constant selectable from 1 tCYC/32 tCYC/128 tCYC)
„Clock Output Function
• Can generate clock outputs with a frequency of 1/1, 1/2, 1/4, 1/8, 1/16, 1/32, 1/64 of the source clock selected as
the system clock.
• Can generate the source clock for the subclock
„Analog Comparator / Amplifier × 2 channels
• Analog comparator / amplifier selectable (each channel)
• Analog comparator Interrupt
„MCPWM: Motor Control 12-bit PWM × 6 channels
• Dead time is programmable.
• Forced stop is possible by the output of the analog comparator and the INT terminals.
• Edge-aligned / center-aligned selectable
„Watchdog Timer
• Can generate the internal reset signal on a timer overflow monitored by the WDT-dedicated low-speed
RC oscillation clock (30kHz).
• Allows selection of continue, stop, or hold mode operation of the counter on entry into the HALT/HOLD mode.
„Interrupts
• 21 sources, 10 vector addresses
1) Provides three levels (low (L), high (H), and highest (X)) of multiplex interrupt control. Any interrupt requests of
the level equal to or lower than the current interrupt are not accepted.
2) When interrupt requests to two or more vector addresses occur at the same time, the interrupt of the highest level
takes precedence over the other interrupts. For interrupts of the same level, the interrupt into the smallest vector
address takes precedence.
No.
Vector Address
Level
1
00003H
X or L
INT0
Interrupt Source
2
0000BH
X or L
INT1
3
00013H
H or L
INT2/T0L/INT4
4
0001BH
H or L
INT3/Base timer
5
00023H
H or L
T0H
6
0002BH
H or L
T1L/T1H
7
00033H
H or L
SIO0/UART1 receive
8
0003BH
H or L
SIO1/UART1 transmit/MCPWM
9
00043H
H or L
ADC/T6/T7
10
0004BH
H or L
Port 0/CMP1/CMP2
• Priority levels X > H > L
• Of interrupts of the same level, the one with the smallest vector address takes precedence.
„Subroutine Stack Levels: 128levels (The stack is allocated in RAM.)
„High-speed Multiplication/Division Instructions
• 16 bits × 8 bits
(5 tCYC execution time)
• 24 bits × 16 bits
(12 tCYC execution time)
• 16 bits ÷ 8 bits
(8 tCYC execution time)
• 24 bits ÷ 16 bits
(12 tCYC execution time)
No.A1828-3/25
LC87F0808A
„Oscillation Circuits
• Internal oscillation circuits
Medium-speed RC oscillation circuit: For system clock (1MHz)
High-speed RC oscillation circuit:
For system clock (20MHz)
Low-speed RC oscillation circuit:
For watch dog timer (30kHz)
• External oscillation circuits
Hi-speed CF oscillation circuit:
For system clock, with internal Rf
Low speed crystal oscillation circuit:
For low-speed system clock, with internal Rf
1) The CF and crystal oscillation circuits share the same pins. The active circuit is selected under program control.
2) The CF and the crystal oscillation circuits stop operating in the system reset state and start oscillating when the
oscillation is enabled with an instruction.
„System Clock Divider Function
• Can run on low current.
• The minimum instruction cycle selectable from 150ns, 300ns, 600ns, 1.2μs, 2.4μs, 4.8μs, 9.6μs, 19.2μs and
38.4μs (at a main clock rate of 20MHz).
„Internal Reset Function
• Power-on reset (POR) function
1) POR reset is generated only at power-on time.
2) The POR release level can be selected from 8 levels (1.67V, 1.97V, 2.07V, 2.37V, 2.57V, 2.87V, 3.86V and
4.35V) through option configuration.
• Low-voltage detection reset (LVD) function
1) LVD and POR functions are combined to generate resets when power is turned on and when power voltage falls
below a certain level.
2) The use/disuse of the LVD function and the low voltage threshold level (7 levels: 1.91V, 2.01V, 2.31V, 2.51V,
2.81V, 3.79V, 4.28V).
„Standby Function
• HALT mode: Halts instruction execution while allowing the peripheral circuits to continue operation.
1) Oscillation is not halted automatically.
2) There are three ways of resetting the HALT mode.
(1) Setting the reset pin to the low level
(2) System resetting by watchdog timer or low-voltage detection
(3) Occurrence of an interrupt
• HOLD mode: Suspends instruction execution and the operation of the peripheral circuits.
1) The CF, RC and crystal oscillators automatically stop operation.
2) There are four ways of resetting the HOLD mode.
(1) Setting the reset pin to the lower level.
(2) System resetting by watchdog timer or low-voltage detection
(3) Having an interrupt source established at either INT0, INT1, INT2 or INT4
* INT0 and INT1 HOLD mode reset is available only when level detection is set.
(4) Having an interrupt source established at port 0.
• X'tal HOLD mode: Suspends instruction execution and the operation of the peripheral circuits except the base timer.
1) The CF and RC oscillator automatically stop operation.
2) The state of crystal oscillation established when the X'tal HOLD mode is entered is retained.
3) There are five ways of resetting the X'tal HOLD mode.
(1) Setting the reset pin to the low level.
(2) System resetting by watchdog timer or low-voltage detection.
(3) Having an interrupt source established at either INT0, INT1, INT2 or INT4
* INT0 and INT1 HOLD mode reset is available only when level detection is set.
(4) Having an interrupt source established at port 0.
(5) Having an interrupt source established in the base timer circuit.
Note: Available only when X’tal oscillation is selected.
No.A1828-4/25
LC87F0808A
„On-chip Debugger
• Supports software debugging with the IC mounted on the target board.
„Data Security Function (flash versions only)
• Protects the program data stored in flash memory from unauthorized read or copy.
Note: This data security function does not necessarily provide absolute data security.
„Package Form
• QFP36 (7×7): Lead-/Halogen-free type
„Development Tools
• On-chip debugger: TCB87 type C + LC87F0808A
„Programming Boards
Package
Programming boards
QFP36(7×7)
W87F24Q
„Flash ROM Programmer
Maker
Model
Single
AF9709/AF9709B/AF9709C
Programmer
(Including Ando Electric Co., Ltd. models)
Flash Support Group, Inc.
(FSG)
AF9723/AF9723B(Main body)
Gang
Programmer
(Including Ando Electric Co., Ltd. models)
AF9833(Unit)
(Including Ando Electric Co., Ltd. models)
Sanyo
Supported Version
Rev 03.28 or later
Device
87f008SU
(3B247)
-
-
-
-
Single/Gang
SKK/SKK Type B
Programmer
(SanyoFWS)
1.06 or later
Gang
SKK-4G
Chip Data Version
Programmer
(SanyoFWS)
Application Version
2.26 or later
Application Version
In-circuit/Gang
SKK-DBG Type C
1.06 or later
Programmer
(SanyoFWS)
Chip Data Version
LC87F0808
2.31 or later
For information about AF-Series:
Flash Support Group, Inc.
TEL: +81-53-459-1050
E-mail: [email protected]
No.A1828-5/25
LC87F0808A
Package Dimensions
unit : mm (typ)
3162C
27
0.5
9.0
7.0
19
28
7.0
9.0
18
36
10
1
9
0.65
0.15
0.3
(1.5)
0.1
1.7max
(0.9)
SANYO : QFP36(7X7)
27
26
25
24
23
22
21
20
19
P03/AN3
P02/AN2
P01/AN1
P00/AN0
VSS2
VDD2
P17/T1PWMH/URX/CMP2O
P16/T1PWML/UTX/CMP2IA
P15/SCK1/CMP2IB
Pin Assignment
18
17
16
15
14
13
12
11
10
LC87F0808A
P14/SI1/SB1/CMP1O
P13/SO1/CMP1IA
P12/SCK0/CMP1IB
P11/SI0/SB0
P10/SO0
P35/PULSG2
P34/PULSG2
P33/PULSG1
P32/PULSG1
1
2
3
4
5
6
7
8
9
28
29
30
31
32
33
34
35
36
P73/INT3/T0HCP/T0IN
RES
OWP0
VSS1
CF1/XT1
CF2/XT2
VDD1
P30/PULSG0
P31/PULSG0
P04/AN4
P05/AN5/CKO
P06/AN6/T6O
P07/AN7/T7O
P20/INT4
P21/INT4/BUZ
P70/INT0/T0LCP
P71/INT1/T0HCP
P72/INT2/T0LCP/T0IN
Top view
SANYO: QFP36 (7×7) “Lead-/Halogen-free Type”
No.A1828-6/25
LC87F0808A
QFP36
NAME
QFP36
NAME
1
P73/INT3/T0HCP/T0IN
19
P15/SCK1/CMP2IB(+)
2
RES
20
P16/T1PWML/UTX/CMP2IA(-)
3
OWP0
21
P17/T1PWMH/URX/CMP2O
4
VSS1
22
VDD2
5
CF1/XT1
23
VSS2
6
CF2/XT2
24
P00/AN0
7
VDD1
25
P01/AN1
8
P30/PULSG0
26
P02/AN2
9
P31/PULSG0
27
P03/AN3
10
P32/PULSG1
28
P04/AN4
11
P33/PULSG1
29
P05/AN5/CKO
12
P34/PULSG2
30
P06/AN6/T6O
13
P35/PULSG2
31
P07/AN7/T7O
14
P10/SO0
32
P20/INT4
15
P11/SI0/SB0
33
P21/INT4/BUZ
16
P12/SCK0/CMP1IB(+)
34
P70/INT0/T0LCP
17
P13/SO1/CMP1IA(-)
35
P71/INT1/T0HCP
18
P14/SI1/SB1/CMP1O
36
P72/INT2/T0LCP/T0IN
No.A1828-7/25
LC87F0808A
System Block Diagram
Interrupt control
IR
Flash ROM
RC
Clock
generator
Standby control
CF/
X'tal
PLA
PC
MRC
ACC
WDT
Reset circuit
(LVD/POR)
SIO0
Reset control
RES
B register
C register
Bus interface
SIO1
Port 0
Timer 0
Port 1
Timer 1
Port 2/INT4
Timer 6
Port 3
Timer 7
Port 7
Base timer
ADC
MCPWM
INT0-2
INT3 (Noise filter)
ALU
PSW
RAR
RAM
Stack pointer
On-chip debugger
UART1
No.A1828-8/25
LC87F0808A
Pin Description
Pin Name
I/O
Description
Option
VSS1,VSS2
-
- Power supply pins
No
VDD1, VDD2
-
+ Power supply pins
No
Port 0
I/O
• 8-bit I/O port
• I/O specifiable in 4-bit units
P00 to P07
• Pull-up resistors can be turned on and off in 4-bit units.
• HOLD reset input
• Port 0 interrupt input
Yes
• Pin functions
P05: System clock output
P06: Timer 6 toggle output
P07: Timer 7 toggle output
P00 (AN0) to P07 (AN7): AD converter input
Port 1
I/O
• 8-bit I/O port
• I/O specifiable in 1-bit units
P10 to P17
• Pull-up resistors can be turned on and off in 1-bit units.
• Pin functions
P10: SIO0 data output
P14: SIO1 data input / bus I/O
P11: SIO0 data input/bus I/O
P15: SIO1 clock I/O
P12: SIO0 clock I/O
P16: Timer 1 PWML output / UART transmit
P13: SIO1 data output
P17: Timer 1 PWMH output / UART receive
Yes
P12 to P17: analog comparator / amplifier I/O pins
P12: CMP1(+) input / AMP1(+) input
P13: CMP1(-) input / AMP1(-) input
P14: CMP1 output / AMP1 output
P15: CMP2(+) input / AMP2(+) input
P16: CMP2(-) input / AMP2(-) input
P17: CMP2 output / AMP2 output
Port 2
I/O
• 2-bit I/O port
• I/O specifiable in 1-bit units
P20 to P21
• Pull-up resistors can be turned on and off in 1-bit units.
• Pin functions
P21: Beeper output
P20 to P21: INT4 input/HOLD reset input/timer 1 event input/timer 0L capture input/
Yes
timer 0H capture input
Interrupt acknowledge types
INT4
Port 3
P30 to P35
I/O
Rising
Falling
enable
enable
Rising &
Falling
enable
H level
L level
disable
disable
• 6-bit I/O port
• I/O specifiable in 1-bit units
• Pull-up resistors can be turned on and off in 1-bit units.
• Pin functions
P30 to p35 : motor control PWM output pins
P30: PULSG0 output
P31: PULSG0 output
Yes
P32: PULSG1 output
P33: PULSG1 output
P34: PULSG2 output
P35: PULSG2 output
Continued on next page.
No.A1828-9/25
LC87F0808A
Continued from preceding page.
Pin Name
Port 7
I/O
Description
Option
• 4-bit I/O port
I/O
• I/O specifiable in 1-bit units
P70 to P73
• Pull-up resistors can be turned on and off in 1-bit units.
• Pin functions
P70: INT0 input/HOLD reset input/timer 0L capture input
P71: INT1 input/HOLD reset input/timer 0H capture input
P72: INT2 input/HOLD reset input/timer 0 event input / timer 0L capture input
P73: INT3 input (with noise filter)/ timer 0 event input/timer 0H capture input
No
Interrupt acknowledge types
INT0
Rising &
Rising
Falling
enable
enable
disable
Falling
H level
L level
enable
enable
INT1
enable
enable
disable
enable
enable
INT2
enable
enable
enable
disable
disable
INT3
enable
enable
enable
disable
disable
OWP0
I/O
On-chip debugger (exclusive pin)
No
RES
I/O
External reset input/internal reset output
No
CF1/XT1
• Ceramic resonator or 32.768kHz crystal oscillator input pin
I
• Pin function
No
General-purpose input port
CF2/XT2
• Ceramic resonator or 32.768kHz crystal oscillator output pin
I/O
• Pin function
No
General-purpose input port
Port Output Types
The table below lists the types of port outputs and the presence/absence of a pull-up resistor.
Data can be read into any input port even if it is in the output mode.
Port Name
Option selected in
units of
Option type
P00 to P07
1 bit
1
P10 to P17
1 bit
P20 to P21
1 bit
Output type
Pull-up resistor
CMOS
Programmable (Note 1)
2
Nch-open drain
No
1
CMOS
Programmable
2
Nch-open drain
Programmable
1
CMOS
Programmable
2
Nch-open drain
Programmable
CMOS
Programmable
Nch-open drain
Programmable
CMOS
Programmable
P30 to P35
1 bit
1
P70 to P73
-
No
2
Note 1: The control of the presence or absence of the programmable pull-up resistors for port 0 and the switching
between low-and high-impedance pull-up connection is exercised in nibble (4-bit) units (P00 to 03 or
P04 to 07).
No.A1828-10/25
LC87F0808A
User Option Table
Option name
Port output type
Option to be applied on
Flash-rom version
Option selected in units of
P00 to P07
{
1 bit
P10 to P17
{
1 bit
P20 to P21
{
1 bit
Option selection
CMOS
Nch-open drain
CMOS
Nch-open drain
CMOS
Nch-open drain
{
P30 to P35
CMOS
1 bit
Nch-open drain
Program start
-
{
-
-
{
-
Detect function
{
-
00000h
address
01E00h
Protect area
00000h to 01BFFh
(Note 1)
01C00h to 01EFFh
Low-voltage
Enable: Use
detection reset
function
Power-on reset
Disable: Not Used
Detect level
{
-
7-level
Power-On reset level
{
-
8-level
function
(Note 1) This option selects the area to be write protected at the time of the On-board writing.
Recommended Unused Pin Connections
Recommended unused pin connections
Port Name
Board
Software
P00 to P07
Open
Output low
P10 to P17
Open
Output low
P20 to P21
Open
Output low
P30 to P35
Open
Output low
P70 to P73
Open
Output low
CF1/XT1
Pulled low with a 100kΩ resistor or less
General-purpose input port
CF2/XT2
Pulled low with a 100kΩ resistor or less
General-purpose input port
On-chip Debugger Pin Connection Requirements
OWP0 of the On-chip-debugger terminal must add pull-down resistor of 100kΩ.
The connection with TCB87 Type C are OWP0/VDD/VSS
Note: Be sure to electrically short-circuit between the VSS1 and VSS2 pins and between the VDD1 and VDD2 pins.
No.A1828-11/25
LC87F0808A
Absolute Maximum Ratings at Ta = 25°C, VSS1 = VSS2 = 0V
Parameter
Symbol
Pin/Remarks
Specification
Conditions
VDD[V]
Maximum supply
VDD max
VDD1
voltage
Input voltage
VI
CF1
Input/output
VIO
CF2
voltage
Ports 0, 1, 2, 3
min
typ
max
-0.3
+6.5
-0.3
VDD+0.3
-0.3
VDD+0.3
unit
V
Port 7
High level output current
Peak output
IOPH(1)
Mean output
CMOS output select
Per 1 applicable pin
IOPH(2)
Port7
Per 1 applicable pin
IOMH(1)
Ports 0, 1, 2, 3
CMOS output select
current
Per 1 applicable pin
-10
-5
-7.5
(Note 1-1)
IOMH(2)
Port7
Per 1 applicable pin
Total output
ΣIOAH(1)
Ports 0, 2, 7
Total of all applicable pins
-25
current
ΣIOAH(2)
Ports 1, 3
Total of all applicable pins
-25
Peak output
IOPL(1)
P02 to P07
Per 1 applicable pin
current
Low level output current
Ports 0, 1, 2, 3
current
Mean output
20
Ports 1, 2, 3
IOPL(2)
P00, P01
Per 1 applicable pin
30
IOPL(3)
Port 7
Per 1 applicable pin
10
IOML(1)
P02 to P07
Per 1 applicable pin
current
(Note 1-1)
-3
15
Ports 1, 2, 3
IOML(2)
P00, P01
Per 1 applicable pin
20
IOML(3)
Port 7
Per 1 applicable pin
7.5
Total output
ΣIOAL(1)
Ports 0, 2, 7
Total of all applicable pins
45
current
ΣIOAL(2)
Ports 1, 3
Total of all applicable pins
45
Pd max(1)
QFP36(7×7)
Ta=-40 to +85°C
Power
Dissipation
115
Package only
Pd max(2)
mA
Ta=-40 to +85°C
mW
Package with thermal
244
resistance board
(Note 1-2)
Operating ambient
Topr
Temperature
Storage ambient
temperature
Tstg
-40
+85
-55
+125
°C
Note 1-1: The mean output current is a mean value measured over 100ms.
Note 1-2: SEMI standards thermal resistance board (size: 76.1×114.3×1.6tmm, glass epoxy) is used.
No.A1828-12/25
LC87F0808A
Allowable Operating Conditions at Ta = -40°C to +85°C, VSS1 = VSS2 = 0V
Parameter
Symbol
Pin/Remarks
Specification
Conditions
VDD[V]
Operating
VDD
VDD1, VDD2
0.142μs ≤ tCYC ≤ 200μs
VHD
VDD1, VDD2
RAM and register contents sustained
sustaining
typ
3.3
supply voltage
Memory
min
in HOLD mode.
max
unit
5.5
2.0
supply voltage
High level
VIH(1)
Ports 1, 2, 3, 7
3.3 to 5.5
0.3VDD+0.7
VDD
input voltage
VIH(2)
Ports 0
3.3 to 5.5
0.3VDD+0.7
VDD
VIH(3)
CF1, CF2, RES
3.3 to 5.5
0.75VDD
VDD
VIL(1)
Ports 1, 2, 3, 7
4.0 to 5.5
VSS
0.1VDD+0.4
3.3 to 4.0
VSS
0.2VDD
VIL(2)
Ports 0
4.0 to 5.5
VSS
0.15VDD+0.4
3.3 to 4.0
VSS
0.2VDD
VIL(3)
CF1, CF2, RES
3.3 to 5.5
VSS
0.25VDD
3.3 to 5.5
0.142
200
3.3 to 5.5
0.1
20
Low level
input voltage
Instruction
V
tCYC
cycle time
μs
(Note 2-1)
External
FEXCF
CF1
• CF2 pin open
• System clock frequency division
system clock
frequency
ratio=1/1
• External system clock duty=50±5%
Oscillation
FmCF(1)
CF1, CF2
frequency
range
20MHz ceramic oscillation
See Fig. 1.
FmCF(2)
CF1, CF2
(Note 2-2)
10MHz ceramic oscillation
See Fig. 1.
FmCF(3)
CF1, CF2
4MHz ceramic oscillation
See Fig. 1.
FmMRC
3.3 to 5.5
20
3.3 to 5.5
10
3.3 to 5.5
4
MHz
Internal High-speed RC oscillation.
1/2 frequency division ration.
(RCCTD=0)
3.3 to 5.5
19.0
20.0
21.0
(Note 2-3)
FmRC
Internal medium-speed RC oscillation
3.3 to 5.5
0.5
1.0
2.0
FmSRC
Internal low-speed RC oscillation
3.3 to 5.5
15
30
60
FsX’tal
XT1, XT2
32.768kHz crystal oscillation
See Fig. 1.
kHz
3.3 to 5.5
32.768
Note 2-1: Relationship between tCYC and oscillation frequency is 3/FmCF at a division ratio of 1/1 and 6/FmCF at
a division ratio of 1/2.
Note 2-2: See Tables 1 and 2 for the oscillation constants.
Note 2-3: When switching the system clock, allow an oscillation stabilization time of 100μs or longer after the
high-speed RC oscillator circuit transmits from the "oscillation stopped" to "oscillation enabled" state.
No.A1828-13/25
LC87F0808A
Electrical Characteristics at Ta = -40°C to +85°C, VSS1 = VSS2 = 0V
Parameter
Symbol
Pin/Remarks
Specification
Conditions
VDD[V]
High level input
IIH(1)
current
Ports 0, 1, 2, 3
Output disabled
Port 7
Pull-up resistor off
RES
VIN=VDD
(Including output Tr's off leakage
min
typ
max
unit
3.3 to 5.5
1
3.3 to 5.5
15
current)
Low level input
IIH(2)
CF1, CF2
VIN=VDD
IIL(1)
Ports 0, 1, 2, 3
Output disabled
Port 7
Pull-up resistor off
RES
VIN=VSS
(Including output Tr's off leakage
current
3.3 to 5.5
-1
VIN=VSS
3.3 to 5.5
-15
μA
current)
IIL(2)
CF1, CF2
High level output
VOH(1)
Ports 0, 1, 2, 7
voltage
VOH(2)
VOH(3)
Port 3
VOH(4)
Low level output
VOL(1)
voltage
VOL(2)
Ports 0, 1, 2, 3
4.5 to 5.5
VDD-1
3.3 to 5.5
VDD-0.4
IOH=-6mA
4.5 to 5.5
VDD-1
IOH=-1.4mA
3.3 to 5.5
VDD-0.4
IOL=10mA
4.5 to 5.5
1.5
IOL=1.4mA
3.3 to 5.5
0.4
VOL(3)
Port 7
IOL=1.4mA
3.3 to 5.5
0.4
VOL(4)
P00, P01
IOL=25mA
4.5 to 5.5
1.5
IOL=4mA
3.3 to 5.5
0.4
VOH=0.9VDD
When Port 0 selected
4.5 to 5.5
VOL(5)
Pull-up resistance
IOH=-1mA
IOH=-0.35mA
Rpu(1)
Ports 0, 1, 2, 3
Port 7
15
35
80
low-impedance pull-up.
Rpu(2)
Port 0
VOH=0.9VDD
When Port 0 selected
V
kΩ
3.3 to 5.5
100
210
400
high-impedance pull-up.
Hysteresis voltage
VHYS
Ports 1, 2, 3, 7
When Port 2 selected INT4.
RES
Pin capacitance
CP
All pins
3.3 to 5.5
0.1VDD
V
3.3 to 5.5
10
pF
For pins other than that under test:
VIN=VSS
f=1MHz
Ta=25°C
No.A1828-14/25
LC87F0808A
Serial I/O Characteristics at Ta = -40°C to +85°C, VSS1 = VSS2 = 0V
SIO0 Serial I/O Characteristics (Note 4-1-1)
Input clock
Symbol
Frequency
tSCK(1)
Low level
tSCKL(1)
Pin/
SCK0(P12)
VDD[V]
min
• See Fig. 5.
tSCK(2)
Low level
tSCKL(2)
tCYC
SCK0(P12)
• CMOS output selected
4/3
• See Fig. 5.
1/2
3.3 to 5.5
tSCK
tSCKH(2)
1/2
Serial input
pulse width
Data setup time
SB0(P11),
SI0(P11)
Data hold time
Input clock
Output delay
tdD0(1)
• Must be specified with
0.05
respect to rising edge of
3.3 to 5.5
SIOCLK.
thDI(1)
time
• See Fig. 5.
SO0(P10),
SB0(P11)
0.05
• Continuous data
(1/3)tCYC
transmission/reception mode
+0.08
(Note 4-1-2)
μs
• Synchronous 8-bit mode
tdD0(2)
(Note 4-1-2)
tdD0(3)
Output clock
Serial output
tsDI(1)
unit
1
pulse width
High level
max
1
tSCKH(1)
Frequency
typ
2
3.3 to 5.5
pulse width
High level
Specification
Conditions
Remarks
pulse width
Output clock
Serial clock
Parameter
(Note 4-1-2)
1tCYC
+0.08
3.3 to 5.5
(1/3)tCYC
+0.08
Note 4-1-1: These specifications are theoretical values. Add margin depending on its use.
Note 4-1-2: Must be specified with respect to falling edge of SIOCLK. Must be specified as the time to the beginning of
output state change in open drain output mode. See Fig. 5.
SIO1 Serial I/O Characteristics (Note 4-2-1)
Input clock
Symbol
Frequency
tSCK(3)
Low level
tSCKL(3)
Pin/
SCK1(P15)
VDD[V]
See Fig. 5.
Frequency
SCK1(P15)
• CMOS output selected
tSCKL(4)
2
1/2
tSCK
tSCKH(4)
1/2
pulse width
Serial input
Data setup time
SB1(P14),
SI1(P14)
• Must be specified with respect
Data hold time
0.05
to rising edge of SIOCLK.
• See Fig. 5.
thDI(2)
3.3 to 5.5
0.05
Output delay time
Serial output
tsDI(2)
unit
1
3.3 to 5.5
pulse width
High level
max
1
• See Fig. 5.
Low level
typ
tCYC
tSCKH(3)
tSCK(4)
min
2
3.3 to 5.5
pulse width
High level
Specification
Conditions
Remarks
pulse width
Output clock
Serial clock
Parameter
tdD0(4)
SO1(P13),
SB1(P14)
μs
• Must be specified with respect
to falling edge of SIOCLK.
• Must be specified as the time
to the beginning of output state
3.3 to 5.5
change in open drain output
(1/3)tCYC
+0.08
mode.
• See Fig. 5.
Note 4-2-1: These specifications are theoretical values. Add margin depending on its use.
No.A1828-15/25
LC87F0808A
Pulse Input Conditions at Ta = -40°C to +85°C, VSS1 = VSS2 = 0V
Parameter
Symbol
Pin/Remarks
Specification
Conditions
VDD[V]
High/low level
tPIH(1)
INT0(P70),
• Interrupt source flag can be set.
pulse width
tPIL(1)
INT1(P71),
• Event inputs for timer 0 or 1 are
INT2(P72),
enabled.
min
typ
3.3 to 5.5
1
3.3 to 5.5
2
max
unit
INT4(P20 to P21)
tPIH(2)
INT3(P73) when noise
• Interrupt source flag can be set.
tPIL(2)
filter time constant is
• Event inputs for timer 0 are
1/1
enabled.
tPIH(3)
INT3(P73) when noise
• Interrupt source flag can be set.
tPIL(3)
filter time constant is
• Event inputs for timer 0 are
1/32
3.3 to 5.5
64
3.3 to 5.5
256
3.3 to 5.5
200
nabled.
tPIH(4)
INT3(P73) when noise
• Interrupt source flag can be set.
tPIL(4)
filter time constant is
• Event inputs for timer 0 are
1/128
tPIL(5)
tCYC
enabled.
• Resetting is enabled.
RES
μs
AD Converter Characteristics at VSS1 = VSS2 = 0V
10bits AD Converter Mode/Ta = -40°C to +85°C
Parameter
Symbol
Pin/Remarks
Specification
Conditions
VDD[V]
Resolution
N
Absolute
ET
AN7(P07)
TCAD
AN9(AMP2O)
(Note 6-1)
typ
max
• See Conversion time calculation
VAIN
3.3 to 5.5
3.3 to 5.5
voltage range
Analog port
IAINH
VAIN=VDD
3.3 to 5.5
input current
IAINL
VAIN=VSS
3.3 to 5.5
unit
10
bit
3.3 to 5.5
formulas. (Note 6-2)
Analog input
min
3.3 to 5.5
AN8(AMP1O)
accuracy
Conversion time
AN0(P00) to
8.5
VSS
±16
LSB
59.5
μs
VDD
V
1
-1
μA
8bits AD Converter Mode/Ta = -40°C to +85°C
Parameter
Symbol
Pin/Remarks
Specification
Conditions
VDD[V]
Resolution
N
Absolute
ET
AN7(P07)
TCAD
AN9(AMP2O)
(Note 6-1)
• See Conversion time calculation
formulas. (Note 6-2)
Analog input
min
typ
3.3 to 5.5
AN8(AMP1O)
accuracy
Conversion time
AN0(P00) to
VAIN
voltage range
max
unit
8
bit
±1.5
3.3 to 5.5
LSB
3.3 to 5.5
2.9
20
μs
3.3 to 5.5
VSS
VDD
V
Analog port
IAINH
VAIN=VDD
3.3 to 5.5
input current
IAINL
VAIN=VSS
3.3 to 5.5
1
-1
μA
Conversion time calculation formulas:
10bits AD Converter Mode: TCAD (Conversion time) = ((42/(AD division ratio))+2)×(1/3)×tCYC
8bits AD Converter Mode: TCAD (Conversion time) = ((28/(AD division ratio))+2)× (1/3)×tCYC
No.A1828-16/25
LC87F0808A
External
Operating supply
oscillation
voltage range
(FmCF)
CF-20MHz
(VDD)
3.3V to 5.5V
System division ratio
Cycle time
(SYSDIV)
(tCYC)
1/1
CF-10MHz
3.3V to 5.5V
CF-4MHz
3.3V to 5.5V
AD division ratio
AD conversion time
(ADDIV)
(TCAD)
10bit AD
8bit AD
10bit AD
8bit AD
150ns
1/4
1/2
8.5μs
2.9μs
1/1
300ns
1/4
1/2
17μs
5.8μs
1/1
750ns
1/4
1/2
42.5μs
14.5μs
Note 6-1: The quantization error (±1/2LSB) must be excluded from the absolute accuracy. The absolute accuracy must
be measured in the microcontroller's state in which no I/O operations occur at the pins adjacent to the analog
input channel.
Note 6-2: The conversion time refers to the period from the time an instruction for starting a conversion process till the
time the conversion results register(s) are loaded with a complete digital conversion value corresponding to
the analog input value.
The conversion time is 2 times the normal-time conversion time when:
• The first AD conversion is performed in the 10-bit AD conversion mode after a system reset.
• The first AD conversion is performed after the AD conversion mode is switched from 8-bit to 10-bit
conversion mode.
Power-on Reset (POR) Characteristics at Ta = -40°C to +85°C, VSS1=VSS2=0V
Specification
Parameter
Symbol
Pin/Remarks
Conditions
Option selected
voltage
POR release
PORRL
voltage
Detection
POUKS
voltage
min
typ
max
• Select from option.
1.67V
1.55
1.67
1.79
(Note 7-1)
1.97V
1.85
1.97
2.09
2.07V
1.95
2.07
2.19
2.37V
2.25
2.37
2.49
2.57V
2.45
2.57
2.69
2.87V
2.75
2.87
2.99
3.86V
3.73
3.86
3.99
4.35V
4.21
4.35
4.49
0.7
0.95
unit
V
• See Fig. 7.
(Note 7-2)
unknown state
Power supply
rise time
PORIS
• Power supply rise
time from 0V to 1.6V.
100
ms
Note7-1: The POR release level can be selected out of 8 levels only when the LVD reset function is disabled.
Note7-2: POR is in an unknown state before transistors start operation.
No.A1828-17/25
LC87F0808A
Low Voltage Detection Reset (LVD) Characteristics at Ta = -40°C to +85°C, VSS1=VSS2=0V
Specification
Parameter
Symbol
Pin/Remarks
Conditions
Option selected
voltage
LVD reset voltage
• Select from option.
LVDET
(Note 8-1)
(Note 8-2)
(Note 8-3)
• See Fig. 8.
LVD hysteresys
LVHYS
width
Detection voltage
min
typ
unit
1.91V
1.81
1.91
2.01
2.01V
1.91
2.01
2.11
2.31V
2.21
2.31
2.41
2.51V
2.41
2.51
2.61
2.81V
2.71
2.81
2.91
3.79V
3.69
3.79
3.89
4.28V
4.18
4.28
4.38
1.91V
55
2.01V
55
2.31V
55
2.51V
55
2.81V
60
3.79V
65
4.28V
65
V
mV
• See Fig. 8.
LVUKS
unknown state
0.7
(Note 8-4)
Low voltage
max
0.95
V
• LVDET-0.5V
TLVDW
• See Fig. 9.
detection
0.2
minimum width
ms
(Reply sensitivity)
Note8-1: The LVD reset level can be selected out of 7 levels only when the LVD reset function is enabled.
Note8-2: LVD reset voltage specification values do not include hysteresis voltage.
Note8-3: LVD reset voltage may exceed its specification values when port output state changes and/or when a large
current flows through port.
Note8-4: LVD is in an unknown state before transistors start operation.
Comparator, Operational Amplifiers Characteristics at Ta=-40 to +85°C, VSS1=VSS2=0V
Function
Parameter
CMP1, 2
Input common-
Symbol
Pin/Remarks
Specification
Conditions
VDD[V]
VCMIN
mode voltage
CMP1IA, CMP1IB
3.3 to
CMP2IA, CMP2IB
5.5
(Note9-1)
Offset voltage
CMP
VOFF(1)
tCRT
response
CMP1IA, CMP1IB
Input common-mode
CMP2IA, CMP2IB
voltage range
CMP1O
• Input common-mode
CMP2O
voltage range
• Input amplitude=100mV
speed
min
typ
max
VDD1.5V
VSS
3.3 to
20
5.5
3.3 to
200
5.5
unit
V
mV
ns
• Over drive=50mV
AMP1, 2
AMP input
VAMIN
CMP1IA, CPM2IA
3.3 to
voltage
5.5
(Note9-1)
Input offset
VOPOFF
voltage
Slew rate
SR
CMP1IA, CMP1IB
Input common-mode
CMP2IA, CMP2IB
voltage range
CMP1O
50pF
CMP2O
Output
Source
IoSource
3.3 to
20
5.5
5.0
V
mV
3
V/μs
CMP1IA,CMP1IB(+)=1V
CMP2IA,CMP2IB(-)=0V
current
VDD1.5V
VSS
5.0
2.5
3.5
mA
5.0
0.3
0.35
mA
CMP1O,CMP2O=VDD-1.5V
Sink
IoSink
CMP1IA,CMP1IB(+)=0V
CMP2IA,CMP2IB(-)=1V
CMP1O,CMP2O=VDD+0.5V
Note9-1: When VDD=5V, input voltage is effective from 0 to 3.5V.
No.A1828-18/25
LC87F0808A
Consumption Current Characteristics at Ta = -40°C to +85°C, VSS1 = VSS2 = 0V
Parameter
Normal mode
Symbol
IDDOP(1)
consumption
Pin/
VDD1,
VDD2
min
typ
max
unit
• FmCF=20MHz ceramic oscillation mode
• System clock set to 20MHz side
3.3 to 5.5
10
12.5
3.3 to 5.5
3
4.1
• 1/1 frequency division ratio
(Note 10-1)
(Note 10-2)
VDD[V]
• All internal RC oscillation stopped.
current
Specification
Conditions
Remarks
• FmCF=4MHz ceramic oscillation mode
IDDOP(2)
• System clock set to 4MHz side
• All internal RC oscillation stopped.
• 1/1 frequency division ratio
• FsX’tal=32.768kHz crystal oscillation mode
IDDOP(3)
• Internal medium speed RC oscillation
stopped.
• System clock set to internal high speed
mA
3.3 to 5.5
9.2
11
3.3 to 5.5
0.5
0.7
3.3 to 5.5
32
74
3.3 to 5.5
4.7
5.8
3.3 to 5.5
1.5
2.3
RC oscillation (20MHz).
• 1/1 frequency division ratio
• FsX’tal=32.768kHz crystal oscillation mode
IDDOP(4)
• Internal high speed RC oscillation stopped.
• System clock set to internal medium speed
RC oscillation.
• 1/2 frequency division ratio
• FsX’tal=32.768kHz crystal oscillation mode
IDDOP(5)
• System clock set to 32.768kHz crystal
oscillation.
μA
• All internal RC oscillation stopped.
• 1/1 frequency division ratio
HALT mode
IDDHALT(1)
consumption
VDD1,
VDD2
• HALT mode
• FmCF=20MHz ceramic oscillation mode
current
• System clock set to 20MHz side
(Note 10-1)
• All internal RC oscillation stopped.
• 1/1 frequency division ratio
(Note 10-2)
IDDHALT(2)
• HALT mode
• FmCF=4MHz ceramic oscillation mode
• System clock set to 4MHz side
• All internal RC oscillation stopped.
• 1/1 frequency division ratio
IDDHALT(3)
• HALT mode
• FsX’tal=32.768kHz crystal oscillation
mA
mode
• Internal medium speed RC oscillation
stopped.
3.3 to 5.5
4
5
3.3 to 5.5
0.3
0.45
3.3 to 5.5
16
60
• System clock set to internal high speed
RC oscillation (20MHz).
• 1/1 frequency division ratio
IDDHALT(4)
• HALT mode
• FsX’tal=32.768kHz crystal oscillation mode
• Internal high speed RC oscillation stopped.
• System clock set to internal medium speed
RC oscillation.
• 1/2 frequency division ratio
IDDHALT(5)
• HALT mode
• FsX’tal=32.768kHz crystal oscillation mode
• System clock set to 32.768kHz crystal
oscillation.
μA
• All internal RC oscillation stopped.
• 1/1 frequency division ratio
Note10-1: Values of the consumption current do not include current that flows into the output transistors and internal
pull-up resistors.
Note10-2: The consumption current values do not include operational current of LVD function if not specified.
Continued on next page.
No.A1828-19/25
LC87F0808A
Continued from preceding page.
Parameter
Symbol
HOLD mode
IDDHOLD(1)
consumption
Pin/
VDD1,
VDD2
Specification
Conditions
Remarks
VDD[V]
min
typ
max
unit
HOLD mode
• CF1=VDD or open
current
3.3 to 5.5
0.03
32
(External clock mode)
(Note 10-1)
IDDHOLD(2)
μA
HOLD mode
(Note 10-2)
• CF1=VDD or open
(Note 10-3)
(External clock mode)
3.3 to 5.5
3
35
• LVD option selected
Note10-1: Values of the consumption current do not include current that flows into the output transistors and internal
pull-up resistors.
Note10-2: The consumption current values do not include operational current of LVD function if not specified.
Note10-3: The amplifier / comparator circuit operates in the HOLD mode.
F-ROM Programming Characteristics at Ta = -40°C to +85°C, VSS1 = VSS2 = 0V
Parameter
Symbol
Pin/Remarks
Specification
Conditions
VDD[V]
IDDFW(1)
Onboard
VDD1, VDD2
min
typ
max
unit
• Only current of the flash block.
3.3 to 5.5
programming
5
10
mA
20
30
ms
40
60
μs
current
Programming
• Erasing time
tFW(1)
time
• Programming time
tFW(2)
3.3 to 5.5
UART (Full Duplex) Operating Conditions at Ta = -40°C to +85°C, VSS1 = VSS2 = 0V
Parameter
Symbol
Pin/Remarks
Specification
Conditions
VDD[V]
Transfer rate
UBR
UTX(P16)
3.3 to 5.5
URX(P17)
Data length
Stop bits
Parity bits
min
typ
16/3
max
unit
8192/3
tCYC
: 7/8/9 bits (LSB first)
: 1 bit (2-bit in continuous data transmission)
: None
Example of Continuous 8-bit Data Transmission Mode Processing (First Transmit Data=55H)
Start bit
Start of
transmission
Stop bit
End of
transmission
Transmit data (LSB first)
UBR
Example of Continuous 8-bit Data Reception Mode Processing (First Receive Data=55H)
Start bit
Start of
reception
Stop bit
Receive data (LSB first)
End of
reception
UBR
No.A1828-20/25
LC87F0808A
Characteristics of a Sample Main System Clock Oscillation Circuit
Given below are the characteristics of a sample main system clock oscillation circuit that are measured using a
SANYO-designated oscillation characteristics evaluation board and external components with circuit constant values
with which the oscillator vendor confirmed normal and stable oscillation.
Table 1 Characteristics of a Sample Main System Clock Oscillator Circuit with a Ceramic Oscillator
„MURATA
Operating
Circuit Constant
Nominal
Type
Frequency
SMD
20MHz
10MHz
4MHz
Oscillator Name
C2
[pF]
[pF]
[Ω]
[Ω]
(5)
(5)
Open
470
3.3 to 5.5
CSTCE20M0G51-R0
Rf
Rd
Voltage Range
C1
[V]
Oscillation
Stabilization Time
typ
max
[ms]
[ms]
Remarks
0.02
LEAD
CSTLS20M0G52-B0
(5)
(5)
Open
330
3.3 to 5.5
0.06
SMD
CSTCE10M0G52-R0
(10)
(10)
Open
470
3.3 to 5.5
0.02
Internal
LEAD
CSTLS10M0G53-B0
(15)
(15)
Open
680
3.3 to 5.5
0.02
C1,C2
SMD
CSTCR4M00G53-R0
(15)
(15)
Open
1.5k
3.3 to 5.5
0.04
LEAD
CSTLS4M00G53-B0
(15)
(15)
Open
1.5k
3.3 to 5.5
0.03
The oscillation stabilization time refers to the time interval that is required for the oscillation to get stabilized after VDD
goes above the operating voltage lower limit (see Figure 3).
Characteristics of a Sample Subsystem Clock Oscillator Circuit
Given below are the characteristics of a sample subsystem clock oscillation circuit that are measured using a SANYOdesignated oscillation characteristics evaluation board and external components with circuit constant values with which
the oscillator vendor confirmed normal and stable oscillation.
Table 2 Characteristics of a Sample Subsystem Clock Oscillator Circuit with a Crystal Oscillator
„EPSON TOYOCOM
Nominal
Type
Frequency
Operating
Circuit Constant
Oscillator
Name
C1
C2
Rf
Rd
[pF]
[pF]
[Ω]
[Ω]
8
8
Open
330k
Voltage Range
[V]
Oscillation
Stabilization Time
typ
max
[s]
[s]
1.0
4.0
Remarks
Applicable
32.768kHz
SMD
MC-306
3.3 to 5.5
CL value =
7.0pF
The oscillation stabilization time refers to the time interval that is required for the oscillation to get stabilized after the
instruction for starting the subclock oscillation circuit is executed and to the time interval that is required for the
oscillation to get stabilized after the HOLD mode is reset (see Figure 3).
Note: The components that are involved in oscillation should be placed as close to the IC and to one another as possible
because they are vulnerable to the influences of the circuit pattern.
CF2/XT2
CF1/XT1
Rf
Rd
C1
CF/X’tal
C2
Figure 1 CF and XT Oscillator Circuit
0.5VDD
Figure 2 AC Timing Measurement Point
No.A1828-21/25
LC87F0808A
VDD
Operating VDD
lower limit
0V
Power supply
Reset time
RES
Internal medium speed
RC oscillation
tmsCF/tmsX’tal
CF1, CF2
Operating
mode
Unpredictable
Reset
Instruction execution
Reset Time and Oscillation Stabilization Time
HOLD reset
signal
HOLD reset signal
absent
HOLD reset signal valid
Internal medium speed
RC oscillation or
low speed RC oscillation
tmsCF/tmsX’tal
CF1, CF2
(Note)
State
HOLD
HALT
HOLD Reset Signal and Oscillation Stabilization Time
Note: External oscillation circuit is selected.
Figure 3 Oscillation Stabilization Times
No.A1828-22/25
LC87F0808A
VDD
Note:
External circuits for reset may vary
depending on the usage of POR and LVD.
Please refer to the user’s manual for more
information.
RRES
RES
CRES
Figure 4 Reset Circuit
SIOCLK:
DATAIN:
DI0
DI1
DI2
DI3
DI4
DI5
DI6
DI7
DATAOUT:
DO0
DO1
DO2
DO3
DO4
DO5
DO6
DO7
tSCK
tSCKL
tSCKH
SIOCLK:
tsDI
thDI
DATAIN:
tdDO
DATAOUT:
Figure 5 Serial I/O Output Waveforms
tPIL
tPIH
Figure 6 Pulse Input Timing Signal Waveform
No.A1828-23/25
LC87F0808A
(a)
POR release voltage
(PORRL)
(b)
VDD
Reset period
100μs or longer
Reset period
Unknown-state
(POUKS)
RES
Figure 7 Waveform observed when only POR is used (LVD not used)
(RESET pin: Pull-up resistor RRES only)
• The POR function generates a reset only when power is turned on starting at the VSS level.
• No stable reset will be generated if power is turned on again when the power level does not go down to the VSS level
as shown in (a). If such a case is anticipated, use the LVD function together with the POR function or implement an
external reset circuit.
• A reset is generated only when the power level goes down to the VSS level as shown in (b) and power is turned on
again after this condition continues for 100μs or longer.
LVD hysteresis width
(LVHYS)
LVD release voltage
(LVDET+LVHYS)
VDD
LVD reset voltage
(LVDET)
Reset period
Reset period
Reset period
Unknown-state
(LVUKS)
RES
Figure 8 Waveform observed when both POR and LVD functions are used
(RESET pin: Pull-up resistor RRES only)
• Resets are generated both when power is turned on and when the power level lowers.
• A hysteresis width (LVHYS) is provided to prevent the repetitions of reset release and entry cycles near the detection
level.
No.A1828-24/25
LC87F0808A
VDD
LVD release voltage
LVD reset voltage
LVDET-0.5V
TLVDW
VSS
Figure 9 Low voltage detection minimum width
(Example of momentary power loss/Voltage variation waveform)
SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using
products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition
ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd.
products described or contained herein.
SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all
semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or
malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise
to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt
safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not
limited to protective circuits and error prevention circuits for safe design, redundant design, and structural
design.
In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are
controlled under any of applicable local export control laws and regulations, such products may require the
export license from the authorities concerned in accordance with the above law.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise,
without the prior written consent of SANYO Semiconductor Co.,Ltd.
Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the
SANYO Semiconductor Co.,Ltd. product that you intend to use.
Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed
for volume production.
Upon using the technical information or products described herein, neither warranty nor license shall be granted
with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third
party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's
intellectual property rights which has resulted from the use of the technical information and products mentioned
above.
This catalog provides information as of August, 2010. Specifications and information herein are subject
to change without notice.
PS No.A1828-25/25