74LVC08A LOW VOLTAGE CMOS QUAD 2-INPUT AND GATE HIGH PERFORMANCE ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ 5V TOLERANT INPUTS HIGH SPEED: tPD = 4.1ns (MAX.) at VCC = 3V POWER DOWN PROTECTION ON INPUTS AND OUTPUTS SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 24mA (MIN) at VCC = 3V PCI BUS LEVELS GUARANTEED AT 24 mA BALANCED PROPAGATION DELAYS: tPLH ≅ tPHL OPERATING VOLTAGE RANGE: VCC(OPR) = 1.65V to 3.6V (1.2V Data Retention) PIN AND FUNCTION COMPATIBLE WITH 74 SERIES 08 LATCH-UP PERFORMANCE EXCEEDS 500mA (JESD 17) ESD PERFORMANCE: HBM > 2000V (MIL STD 883 method 3015); MM > 200V DESCRIPTION The 74LVC08A is a low voltage CMOS QUAD 2-INPUT AND GATE fabricated with sub-micron silicon gate and double-layer metal wiring C2MOS technology. It is ideal for 1.65 to 3.6 VCC SOP TSSOP ORDER CODES PACKAGE TUBE T&R SOP TSSOP 74LVC08AM 74LVC08AMTR 74LVC08ATTR operations and low power and low noise applications. It can be interfaced to 5V signal environment for inputs in mixed 3.3/5V system. It has more speed performance at 3.3V than 5V AC/ACT family, combined with a lower power consumption. All inputs and outputs are equipped with protection circuits against static discharge, giving them 2KV ESD immunity and transient excess voltage. PIN CONNECTION AND IEC LOGIC SYMBOLS February 2002 1/8 74LVC08A INPUT AND OUTPUT EQUIVALENT CIRCUIT PIN DESCRIPTION PIN No SYMBOL 1, 4, 9, 12 2, 5, 10, 13 3, 6, 8, 11 7 1A to 4A 1B to 4B 1Y to 4Y GND V CC 14 TRUTH TABLE NAME AND FUNCTION Data Inputs Data Inputs Data Outputs Ground (0V) A B Y L L H H L H L H L L L H Positive Supply Voltage ABSOLUTE MAXIMUM RATINGS Symbol V CC Parameter Value Unit Supply Voltage -0.5 to +7.0 V VI DC Input Voltage -0.5 to +7.0 V VO DC Output Voltage (V CC = 0V) VO DC Output Voltage (High or Low State) (note 1) -0.5 to +7.0 V -0.5 to VCC + 0.5 - 50 V mA IIK DC Input Diode Current IOK DC Output Diode Current (note 2) - 50 mA IO DC Output Current ± 50 mA ICC or IGND DC VCC or Ground Current per Supply Pin Storage Temperature Tstg TL Lead Temperature (10 sec) ± 100 mA -65 to +150 °C 300 °C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied 1) IO absolute maximum rating must be observed 2) VO < GND 2/8 74LVC08A RECOMMENDED OPERATING CONDITIONS Symbol V CC Parameter Value Supply Voltage (note 1) Unit 1.65 to 3.6 V 0 to 5.5 V Output Voltage (V CC = 0V) 0 to 5.5 V Output Voltage (High or Low State) 0 to VCC V mA VI Input Voltage VO VO IOH, IOL High or Low Level Output Current (V CC = 3.0 to 3.6V) ± 24 IOH, IOL High or Low Level Output Current (V CC = 2.7 to 3.0V) High or Low Level Output Current (V CC = 2.3 to 2.7V) ± 12 mA ±8 mA IOH, IOL IOH, IOL Top dt/dv High or Low Level Output Current (V CC = 1.65 to 2.3V) Operating Temperature Input Rise and Fall Time (note 2) ±4 mA -55 to 125 °C 0 to 10 ns/V 1) Truth Table guaranteed: 1.2V to 3.6V 2) VIN from 0.8V to 2V at VCC = 3.0V DC SPECIFICATIONS Test Condition Symbol VIH VIL V OH VOL II Ioff ICC ∆ICC Parameter Value -40 to 85 °C -55 to 125 °C VCC (V) Min. High Level Input Voltage 1.65 to 1.95 0.65VCC 0.65VCC 2.3 to 2.7 2.7 to 3.6 1.7 2 1.7 2 Low Level Input Voltage 1.65 to 1.95 0.35VCC 0.35VCC 2.3 to 2.7 2.7 to 3.6 0.7 0.8 0.7 0.8 High Level Output Voltage 1.65 to 3.6 IO=-100 µA VCC-0.2 VCC-0.2 1.65 IO=-4 mA 1.2 1.2 Low Level Output Voltage Input Leakage Current Power Off Leakage Current Quiescent Supply Current ICC incr. per Input Max. Min. 2.3 IO=-8 mA 1.7 1.7 2.7 IO=-12 mA 2.2 2.2 3.0 IO=-18 mA 2.4 2.4 2.2 Unit Max. V V V 3.0 IO=-24 mA 1.65 to 3.6 IO=100 µA 0.2 0.2 1.65 IO=4 mA 0.45 0.45 2.3 IO=8 mA 0.7 0.7 2.7 IO=12 mA 0.4 0.4 3.0 IO=24 mA 0.55 0.55 3.6 VI = 0 to 5.5V ±5 ±5 µA 0 V I or VO = 5.5V 10 10 µA VI = VCC or GND 10 10 VI or VO = 3.6 to 5.5V V IH = VCC-0.6V ± 10 ± 10 500 500 3.6 2.7 to 3.6 2.2 V µA µA 3/8 74LVC08A DYNAMIC SWITCHING CHARACTERISTICS Test Condition Symbol VOLP V OLV Parameter Value TA = 25 °C VCC (V) Dynamic Low Level Quiet Output (note 1) 3.3 Min. Typ. Unit Max. 0.8 CL = 50pF VIL = 0V, V IH = 3.3V V -0.8 1) Number of output defined as ”n”. Measured with ”n-1” outputs switching from HIGH to LOW or LOW to HIGH. The remaining output is measured in the LOW state. AC ELECTRICAL CHARACTERISTICS Test Conditio n Symbol tPLH t PHL tOSLH tOSHL Parameter Propagation Delay Time Output To Output Skew Time (note1, 2) Value VCC (V) CL (pF) RL (Ω) ts = tr (ns) 1.65 to 1.95 2.3 to 2.7 2.7 3.0 to 3.6 2.7 to 3.6 30 30 50 50 1000 500 500 500 2.0 2.0 2.5 2.5 -40 to 85 °C Min. 1 Max. 9.0 6.0 4.8 4.1 1 -55 to 125 °C Min. 1 Unit Max. 12 8.0 5.8 5.0 1 ns ns 1) Skew is defined as the absolute value of the difference between the actual propagation delay for any two outputs of the same device switching in the same direction, either HIGH or LOW (tOSLH = | tPLHm - tPLHn|, tOSHL = | tPHLm - tPHLn| 2) Parameter guaranteed by design CAPACITIVE CHARACTERISTICS Test Condition Symbol Parameter CIN Input Capacitance CPD Power Dissipation Capacitance (note 1) TA = 25 °C VCC (V) 1.8 2.5 3.3 Value Min. fIN = 10MHz Typ. Unit Max. 4 pF 33 36 38 pF 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/n (per circuit) 4/8 74LVC08A TEST CIRCUIT R T = ZOUT of pulse generator (typically 50Ω) TEST CIRCUIT AND WAVEFORM SYMBOL VALUE VCC Symbol 1.65 to 1.95V 2.3 to 2.7V 2.7V 3.0 to 3.6V CL 30pF 30pF 50pF 50pF RL 1000Ω 500Ω 500Ω 500Ω V IH VCC VCC 2.7V 2.7V VM VCC/2 VCC/2 1.5V 1.5V VOH VCC VCC 3.0V 3.0V tr = tr <2.0ns <2.0ns <2.5ns <2.5ns WAVEFORM: PROPAGATION DELAY (f=1MHz; 50% duty cycle) 5/8 74LVC08A SO-14 MECHANICAL DATA DIM. mm. MIN. TYP A a1 inch MAX. MIN. TYP. 1.75 0.1 0.068 0.2 a2 MAX. 0.003 0.007 1.65 0.064 b 0.35 0.46 0.013 0.018 b1 0.19 0.25 0.007 0.010 C 0.5 0.019 c1 45° (typ.) D 8.55 8.75 0.336 0.344 E 5.8 6.2 0.228 0.244 e 1.27 0.050 e3 7.62 0.300 F 3.8 4.0 0.149 0.157 G 4.6 5.3 0.181 0.208 L 0.5 1.27 0.019 0.050 M S 0.68 0.026 8° (max.) PO13G 6/8 74LVC08A TSSOP14 MECHANICAL DATA mm. inch DIM. MIN. TYP A MAX. MIN. TYP. MAX. 1.2 A1 0.05 A2 0.8 b 0.047 0.15 0.002 0.004 0.006 1.05 0.031 0.039 0.041 0.19 0.30 0.007 0.012 c 0.09 0.20 0.004 0.0089 D 4.9 5 5.1 0.193 0.197 0.201 E 6.2 6.4 6.6 0.244 0.252 0.260 E1 4.3 4.4 4.48 0.169 0.173 0.176 1 e 0.65 BSC K 0° L 0.45 A 0.60 0.0256 BSC 8° 0° 0.75 0.018 8° 0.024 0.030 A2 A1 b e K c L E D E1 PIN 1 IDENTIFICATION 1 0080337D 7/8 74LVC08A Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics 2002 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom - United States. http://www.st.com 8/8