STMICROELECTRONICS LM117_10

LM117
LM217, LM317
1.2 V to 37 V adjustable voltage regulators
Features
■
Output voltage range: 1.2 to 37 V
■
Output current in excess of 1.5 A
■
0.1% Line and load regulation
■
Floating operation for high voltages
■
Complete series of protections: current limiting,
thermal shutdown and SOA control
TO-220
TO-220FP
Description
The LM117, LM217, LM317 are monolithic
integrated circuits in TO-220, TO-220FP, TO-3
and D²PAK packages intended for use as positive
adjustable voltage regulators.
D²PAK
They are designed to supply more than 1.5 A of
load current with an output voltage adjustable
over a 1.2 to 37 V range.
TO-3
The nominal output voltage is selected by means
of only a resistive divider, making the device
exceptionally easy to use and eliminating the
stocking of many fixed regulators.
Table 1.
Device summary
Order codes
TO-220
D²PAK (tape and reel)
TO-220FP
TO-3
LM117K
LM217T
LM217D2T-TR
LM317T
LM317D2T-TR
March 2010
Doc ID 2154 Rev 15
LM217K
LM317P
LM317K
1/25
www.st.com
25
Contents
LM117, LM217, LM317
Contents
1
Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2
Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3
Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
5
Typical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
6
Application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
7
Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
8
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
2/25
Doc ID 2154 Rev 15
LM117, LM217, LM317
1
Pin configuration
Figure 1.
Pin connections (top view)
Pin configuration
TO-220
TO-220FP
D²PAK (Any Type)
TO-3
Doc ID 2154 Rev 15
3/25
Maximum ratings
LM117, LM217, LM317
2
Maximum ratings
Table 2.
Absolute maximum ratings
Symbol
VI - VO
IO
TOP
PD
TSTG
Parameter
Value
Input-reference differential voltage
Unit
40
V
Output current
Internally limited
Operating junction temperature for:
LM117
-55 to 150
LM217
-25 to 150
LM317
0 to 125
Power dissipation
°C
Internally limited
Storage temperature
-65 to 150
°C
Note:
Absolute maximum ratings are those values beyond which damage to the device may occur.
Functional operation under these condition is not implied.
Table 3.
Thermal data
Symbol
Parameter
RthJC
Thermal resistance junction-case
RthJA
Thermal resistance junction-ambient
4/25
D²PAK
TO-220
TO-220FP
TO-3
Unit
3
3
5
4
°C/W
62.5
50
60
35
°C/W
Doc ID 2154 Rev 15
LM117, LM217, LM317
3
Diagram
Figure 2.
Schematic diagram
Diagram
Doc ID 2154 Rev 15
5/25
Electrical characteristics
4
LM117, LM217, LM317
Electrical characteristics
VI - VO = 5 V, IO = 500 mA, IMAX = 1.5 A and PMAX = 20 W, TJ = - 55 to 150 °C for LM117,
TJ = - 25 to 150 °C for LM217, unless otherwise specified.
Table 4.
Symbol
ΔVO
ΔVO
Electrical characteristics for LM117/LM217
Parameter
Line regulation
Test conditions
TJ = 25°C
VI - VO = 3 to 40 V
VO ≤5 V
IO = 10 mA to IMAX
TJ = 25°C
VO ≥5 V,
IO = 10 mA to IMAX
TJ = 25°C
Adjustment pin current
ΔIADJ
Adjustment pin current
VI - VO = 2.5 to 40V
VREF
Reference voltage
(between pin 3 and pin 1)
VI - VO = 2.5 to 40V IO= 10 mA to IMAX
PD ≤ PMAX
Minimum load current
IO(max)
Maximum load current
SVR
Unit
0.01
0.02
0.02
0.05
5
15
20
50
0.1
0.3
0.3
1
50
100
µA
0.2
5
µA
1.25
1.3
V
mV
%
IO = 10 mA to IMAX
1.2
Output noise voltage
(percentage of VO)
1
VI - VO = 40 V
3.5
VI - VO ≤ 15 V, PD < PMAX
1.5
Doc ID 2154 Rev 15
mA
2.2
0.003
CADJ=0
CADJ=10µF
5
0.4
B = 10Hz to 100kHz, TJ = 25°C
Supply voltage rejection (1) TJ = 25°C, f = 120Hz
%
A
VI - VO = 40 V, PD < PMAX, TJ = 25°C
1. CADJ is connected between pin 1 and ground.
6/25
Max.
%/V
Output voltage
temperature stability
IO(min)
eN
Typ.
Load regulation
IADJ
ΔVO/VO
Min.
%
65
dB
66
80
LM117, LM217, LM317
Electrical characteristics
VI - VO = 5 V, IO = 500 mA, IMAX = 1.5 A and PMAX = 20 W, TJ = 0 to 125°C, unless otherwise
specified.
Table 5.
Symbol
ΔVO
ΔVO
Electrical characteristics for LM317
Parameter
Line regulation
Test conditions
VI - VO = 3 to 40 V
TJ = 25°C
VO ≤ 5 V
IO = 10 mA to IMAX
TJ = 25°C
VO ≥5 V,
IO = 10 mA to IMAX
TJ = 25°C
Adjustment pin current
ΔIADJ
Adjustment pin current
VI - VO = 2.5 to 40V,
IO = 10 mA to 500mA
VREF
Reference voltage
(between pin 3 and pin 1)
VI - VO = 2.5 to 40V IO = 10 mA to 500mA
PD ≤ PMAX
Minimum load current
IO(max)
Maximum load current
SVR
Max.
Unit
0.01
0.04
0.02
0.07
5
25
20
70
0.1
0.5
0.3
1.5
50
100
µA
0.2
5
µA
1.25
1.3
V
%/V
mV
%
1.2
Output voltage
temperature stability
IO(min)
eN
Typ.
Load regulation
IADJ
ΔVO/VO
Min.
Output noise voltage
(percentage of VO)
1
VI - VO = 40 V
3.5
VI - VO ≤ 15 V, PD < PMAX
1.5
mA
2.2
0.4
B = 10Hz to 100kHz, TJ = 25°C
0.003
CADJ=0
CADJ=10µF
10
A
VI - VO = 40 V, PD < PMAX, TJ = 25°C
Supply voltage rejection (1) TJ = 25°C, f = 120Hz
%
%
65
dB
66
80
1. CADJ is connected between pin 1 and ground.
Doc ID 2154 Rev 15
7/25
Typical characteristics
LM117, LM217, LM317
5
Typical characteristics
Figure 3.
Output current vs. input-output
differential voltage
Figure 5.
Reference voltage vs. junction
Figure 6.
Basic adjustable regulator
8/25
Figure 4.
Doc ID 2154 Rev 15
Dropout voltage vs. junction
temperature
LM117, LM217, LM317
6
Application information
Application information
The LM117, LM217, LM317 provides an internal reference voltage of 1.25 V between the
output and adjustments terminals. This is used to set a constant current flow across an
external resistor divider (see Figure 3), giving an output voltage VO of:
VO = VREF (1 + R2/R1) + IADJ R2
The device was designed to minimize the term IADJ (100 µA max) and to maintain it very
constant with line and load changes. Usually, the error term IADJ × R2 can be neglected. To
obtain the previous requirement, all the regulator quiescent current is returned to the output
terminal, imposing a minimum load current condition. If the load is insufficient, the output
voltage will rise. Since the LM117, LM217, LM317 is a floating regulator and "sees" only the
input-to-output differential voltage, supplies of very high voltage with respect to ground can
be regulated as long as the maximum input-to-output differential is not exceeded.
Furthermore, programmable regulator are easily obtainable and, by connecting a fixed
resistor between the adjustment and output, the device can be used as a precision current
regulator. In order to optimize the load regulation, the current set resistor R1 (see Figure 3)
should be tied as close as possible to the regulator, while the ground terminal of R2 should
be near the ground of the load to provide remote ground sensing. Performance may be
improved with added capacitance as follow:
An input bypass capacitor of 0.1 µF
An adjustment terminal to ground 10 µF capacitor to improve the ripple rejection of about 15
dB (CADJ).
An 1 µF tantalum (or 25 µF Aluminium electrolytic) capacitor on the output to improve
transient response. In additional to external capacitors, it is good practice to add protection
diodes, as shown in Figure 4 D1 protect the device against input short circuit, while D2
protect against output short circuit for capacitance discharging.
Figure 7.
Voltage regulator with protection diodes
Note:
D1 protect the device against input short circuit, while D2 protects against output short
circuit for capacitors discharging.
Doc ID 2154 Rev 15
9/25
Application information
Figure 8.
Slow turn-on 15 V regulator
Figure 9.
Current regulator
LM117, LM217, LM317
IO = (VREF / R1) + IADJ = 1.25 V / R1
Figure 10. 5 V electronic shut-down regulator
10/25
Doc ID 2154 Rev 15
LM117, LM217, LM317
Application information
Figure 11. Digitally selected outputs
(R2 sets maximum VO)
Figure 12. Battery charger (12 V)
* RS sets output impedance of charger ZO = RS (1 + R2/R1). Use of RS allows low charging rates whit fully
charged battery.
Doc ID 2154 Rev 15
11/25
Application information
LM117, LM217, LM317
Figure 13. Current limited 6 V charger
* R3 sets peak current (0.6 A for 1 0).
** C1 recommended to filter out input transients.
12/25
Doc ID 2154 Rev 15
LM117, LM217, LM317
7
Package mechanical data
Package mechanical data
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK® is an ST trademark.
Table 6.
TO-220 mechanical data
Type STD - ST Dual Gauge
Type STD - ST Single Gauge
mm.
mm.
Dim.
Min.
Typ.
Max.
Min.
Typ.
Max.
A
4.40
4.60
4.40
4.60
b
0.61
0.88
0.61
0.88
b1
1.14
1.70
1.14
1.70
c
0.48
0.70
0.48
0.70
D
15.25
15.75
15.25
15.75
D1
1.27
E
10.00
10.40
10.00
10.40
e
2.40
2.70
2.40
2.70
e1
4.95
5.15
4.95
5.15
F
1.23
1.32
0.51
0.60
H1
6.20
6.60
6.20
6.60
J1
2.40
2.72
2.40
2.72
L
13.00
14.00
13.00
14.00
L1
3.50
3.93
3.50
3.93
L20
16.40
16.40
L30
28.90
28.90
∅P
3.75
3.85
3.75
3.85
Q
2.65
2.95
2.65
2.95
Doc ID 2154 Rev 15
13/25
Package mechanical data
LM117, LM217, LM317
Figure 14. Drawing dimension TO-220 (type STD-ST Dual Gauge)
0015988/A
Note:
14/25
1
Max resin gate protrusion: 0.5 mm.
2
Resin gate position is accepted in each of the two positions shown on the dwg, or their
symmetrical.
Doc ID 2154 Rev 15
LM117, LM217, LM317
Package mechanical data
Figure 15. Drawing dimension TO-220 (type STD-ST Single Gauge)
8174627_B
Note:
In spite of some difference in tolerances, the packages are compatible.
Doc ID 2154 Rev 15
15/25
Package mechanical data
LM117, LM217, LM317
Figure 16. Drawing dimension tube for TO-220 Dual Gauge (mm.)
Figure 17. Drawing dimension tube for TO-220 Single Gauge (mm.)
16/25
Doc ID 2154 Rev 15
LM117, LM217, LM317
Package mechanical data
TO-3 mechanical data
mm.
Dim.
Min.
A
inch.
Typ.
Max.
Min.
Typ.
11.85
B
0.96
Max.
0.466
1.05
1.10
0.037
0.041
0.043
C
1.70
0.066
D
8.7
0.342
E
20.0
0.787
G
10.9
0.429
N
16.9
0.665
P
26.2
R
3.88
1.031
4.09
U
0.152
39.5
V
1.555
30.10
1.185
A
P
D
C
O
N
B
V
E
G
U
0.161
R
P003C/C
Doc ID 2154 Rev 15
17/25
Package mechanical data
LM117, LM217, LM317
TO-220FP mechanical data
Dim.
mm.
Min.
Typ
inch.
Max.
Min.
Typ.
Max.
A
4.40
4.60
0.173
0.181
B
2.5
2.7
0.098
0.106
D
2.5
2.75
0.098
0.108
E
0.45
0.70
0.017
0.027
F
0.75
1
0.030
0.039
F1
1.15
1.50
0.045
0.059
F2
1.15
1.50
0.045
0.059
G
4.95
5.2
0.194
0.204
G1
2.4
2.7
0.094
0.106
H
10.0
10.40
0.393
L2
L3
16
0.409
0.630
28.6
30.6
1.126
1.204
L4
9.8
10.6
0.385
0.417
L5
2.9
3.6
0.114
0.142
L6
15.9
16.4
0.626
0.645
L7
9
9.3
0.354
0.366
DIA.
3
3.2
0.118
0.126
7012510A-H
18/25
Doc ID 2154 Rev 15
LM117, LM217, LM317
Package mechanical data
Figure 18. Drawing dimension D²PAK (type STD-ST)
0079457/L
Doc ID 2154 Rev 15
19/25
Package mechanical data
LM117, LM217, LM317
Figure 19. Drawing dimension D²PAK (type WOOSEOK-SUBCON.)
0079457/L
20/25
Doc ID 2154 Rev 15
LM117, LM217, LM317
Table 7.
D²PAK mechanical data
Dim.
MIN.
Type STD-ST
Type WOOSEOK-Subcon.
mm.
mm.
TYP.
MAX.
MIN.
TYP.
MAX.
A
4.40
4.60
4.30
4.70
A1
0.03
0.23
0
0.20
b
0.70
0.93
0.70
0.90
b2
1.14
1.70
1.17
1.37
c
0.45
0.60
0.45
0.50
0.60
c2
1.23
1.36
1.25
1.30
1.40
D
8.95
9.35
9
9.20
9.40
D1
7.50
E
10
E1
8.50
e
7.50
10.40
9.80
10.20
7.50
2.54
2.54
e1
4.88
5.28
H
15
15.85
15
J1
2.49
2.69
2.20
2.60
L
2.29
2.79
1.79
2.79
L1
1.27
1.40
1
1.40
L2
1.30
1.75
1.20
1.60
R
V2
Note:
Package mechanical data
5.08
0.4
0°
15.30
15.60
0.30
8°
0°
3°
The D²PAK package coming from the subcontractor Wooseok is fully compatible with the
ST's package suggested footprint.
Doc ID 2154 Rev 15
21/25
Package mechanical data
LM117, LM217, LM317
Figure 20. D²PAK footprint recommended data
Table 8.
Footprint data
Values
22/25
Dim.
mm.
inch.
A
12.20
0.480
B
9.75
0.384
C
16.90
0.665
D
3.50
0.138
E
1.60
0.063
F
2.54
0.100
G
5.08
0.200
Doc ID 2154 Rev 15
LM117, LM217, LM317
Package mechanical data
Tape & reel D2PAK-P2PAK-D2PAK/A-P2PAK/A mechanical data
mm.
inch.
Dim.
Min.
Typ.
A
Max.
Min.
Typ.
180
13.0
7.086
C
12.8
D
20.2
0.795
N
60
2.362
T
13.2
Max.
0.504
0.512
14.4
0.519
0.567
Ao
10.50
10.6
10.70
0.413
0.417
0.421
Bo
15.70
15.80
15.90
0.618
0.622
0.626
Ko
4.80
4.90
5.00
0.189
0.193
0.197
Po
3.9
4.0
4.1
0.153
0.157
0.161
P
11.9
12.0
12.1
0.468
0.472
0.476
Doc ID 2154 Rev 15
23/25
Revision history
LM117, LM217, LM317
8
Revision history
Table 9.
Document revision history
Date
Revision
01-Sep-2004
10
Mistake VREF ==> VO, tables 1, 4 and 5.
19-Jan-2007
11
D²PAK mechanical data has been updated, add footprint data and the
document has been reformatted.
13-Jun-2007
12
Change values ΔIADJ and VREF test condition of IO = 10 mA to IMAX ==>
IO = 10 mA to 500 mA on Table 5.
23-Nov-2007
13
Added Table 1.
06-Feb-2008
14
Added: TO-220 mechanical data Figure 14 on page 14 and Table 6 on
page 13.
02-Mar-2010
15
Added: notes Figure 14 on page 14, Figure 15 on page 15, Figure 16 and
Figure 17 on page 16.
24/25
Changes
Doc ID 2154 Rev 15
LM117, LM217, LM317
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2010 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
Doc ID 2154 Rev 15
25/25