LD3980 Low drop - Low supply voltage Low ESR capacitor compatible Feature summary ■ Input voltage from 1.7 to 3.6V ■ Ultra low dropout voltage (130mV typ. at 300mA load) ■ Very low quiescent current (110µA typ. at no load, 130µA max. at 300mA load; max 0.5µA in OFF MODE) ■ Output voltage tolerance: +/- 1.0% @ 25°C, +/2.0% full temperature range ■ Guaranteed output current up to 300mA ■ Wide range of output voltage: 0.8V to 3.0V ■ Logic-controlled electronic shutdown ■ Compatible with ceramic capacitor CO = 1µF ■ Internal current and thermal limit ■ Temperature range: -40°C to 85°C Description The LD3980 provides up to 300mA, from 1.7V to 3.6V input voltage. It can deliver a guaranteed 300mA continuous load current with a low 100mV dropout. It is stable with ceramic capacitor. The DFN6 (3x3) ultra low drop-voltage, low quiescent current and low noise makes it suitable for low power applications and in battery powered systems. High power supply rejection is maintained down to low input voltage levels common to battery operated circuits. Shutdown Logic Control function is available this means that when the device is used as local regulator, it is possible to put a part of the board in standby, decreasing the total power consumption. The device also includes a constant current limiting and thermal overload protection. Typical applications are in mobile phone, personal digital assistant (PDAs), cordless phone and similar battery powered wireless systems, portable information appliances.. Block diagram December 2006 Rev. 1 1/16 www.st.com 16 LD3980 Contents 1 Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 Typical application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 5 Typical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 6 Detailed description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 6.1 Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 6.2 Current limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 6.3 Thermal overload protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 6.4 Power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 6.5 Output capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 7 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 8 Order code 9 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 2/16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 LD3980 Pin configuration 1 Pin configuration Figure 1. Pin connections Table 1. Pin description Pin N° Symbol 1 OUT 2, 3 NC 4 GND 5 SHDN 6 IN Table 2. Symbol RthJA Name and function Output Voltage of the LDO Not connected Common ground. SHUTDOWN Input Voltage: Active-Low Shutdown input. A logic Low reduces supply current to below 1µA. Connect to IN or logic high for normal operation Input Voltage of the LDO Thermal data Parameter Thermal resistance junction-ambient Value Unit 55 °C/W 3/16 Maximum ratings LD3980 2 Maximum ratings Table 3. Absolute maximum ratings Symbol Note: 4/16 Parameter Value Unit -0.3 to 4.6 V VI DC Input voltage VO DC Output voltage -0.3 to VI +0.3 V VSHDN Shutdown input voltage -0.3 to VI +0.3 V VRESET Reset output voltage -0.3 to VI +0.3 V IO Output current Internally limited mA PD Power dissipation Internally limited mW TSTG Storage temperature range -65 to 150 °C TOP Operating junction temperature range -40 to 85 °C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition is not implied. LD3980 Typical application 3 Typical application Figure 2. Application circuit 5/16 Electrical characteristics LD3980 4 Electrical characteristics Table 4. Electrical characteristics (TJ = 25°C, VI = VO(NOM) +0.5V, CI = CO = 1µF, IO = 1mA, VSHDN = VI, unless otherwise specified) (Note: 1) Symbol Parameter Test conditions Max. Unit 1.7 3.6 V IO = 300mA -1.0 +1.0 TJ = -40° to 85°C -2.0 +2.0 -0.15 VI Operating input voltage VO VO Accuracy ∆VO Line regulation VI = VO + 0.5V to 3.6V, IO = 1mA ∆VO Load regulation VDROP eN % +0.15 %/V IO = 1mA to 300mA 0.2 0.3 %/mA Dropout voltage (Note 2) IO = 300mA, VO ≥ 1.8V TJ = -40° to 85°C 130 150 mV Output noise voltage 10Hz to 100KHz, IO = 10mA, Quiescent current ON MODE: VSHDN=1.4V IQ Typ. 0.01 Supply voltage rejection (Figure 7.) SVR Min. 110.7 VI = VO(NOM)+0.5V±VRIPPLE VRIPPLE = 0.1V, f = 1KHz, IO = 10mA 60 VIN = VO(NOM)+0.5V±VRIPPLE VRIPPLE = 0.1V, f=10KHz, IO = 10mA 58 IO=0mA 90 µVRMS/VO dB IO=0mA, TJ = -40° to 85°C 110 IO=0 to 300mA 105 IO=0 to 300mA, TJ = -40° to 85°C µA 130 Quiescent current V input current OFF MODE: VSHDN=GND I 0.15 ISC Short circuit current RL=0 650 mA IO(PK) Peak output current VO ≥ VO(NOM) -5% 610 mA 0.4 Shutdown input logic low VSHDN Shutdown input logic high ISHDN TON TSHDN CO Note: 6/16 0.5 VI = 1.6V to 3.6V TJ = -40° to 85°C V 1.4 Shutdown input current VSHDN=GND or VI 0.1 100 nA Turn on time Note 3 120 µs Thermal shutdown Note 4 140 °C Capacitance 1 10 µF ESR 10 5000 mΩ Output capacitor 1 For VO(NOM) < 1.2V, VI=1.7V 2 Dropout voltage is the input-to-output voltage difference at which the output voltage is 100mV below its nominal value. This specification does not apply for output voltages below 1.7V. 3 Turn-on time is time measured between the enable input just exceeding VSHDN High Value and the output voltage just reaching 95% of its nominal value 4 Typical thermal protection hysteresis is 15°C. LD3980 Typical characteristics 5 Typical characteristics Figure 3. Output voltage vs temperature Figure 4. Output voltage vs input voltage Figure 5. Inhibit voltage vs temperature Figure 6. Dropout voltage vs temperature Figure 7. S.V.R. vs frequency Figure 8. Stability value VI=VO(NOM) +0.5V+VRIPPLE, IO=10mA CI =CO= 1µF VI= from 1.76 to 3.6V, IO=from 1mA to 0.3A 7/16 Typical characteristics Figure 9. Stability value VI= from 1.76 to 3.6V, IO=from 1mA to 0.3A Figure 11. Line transient VINH=VI, IO=1mA No CI, CO= 1µF, TRISE=TFALL=1µs 8/16 LD3980 Figure 10. Load transient VINH=VI, IO=10 to 300mA No CO,CI= 1µF, TRISE=TFALL=5µs LD3980 6 Detailed description Detailed description The device is a low-dropout, low quiescent current linear regulator designed primarily for battery-powered applications. It supplies a regulated output voltage for load currents up to 300mA. The LD3980 consists of a precision bandgap, error amplifier, output p-channel MOS. The 0.7V bandgap reference is connected to the error amplifier. The error amplifier compares this reference to the feedback voltage and amplifies the difference. The MOSFET driver reads the error signal and applies the appropriate drive to the P-channel pass transistor. If the feedback voltage is lower than reference voltage, the pass transistor is pulled lower, allowing more current to pass and increasing the output voltage. If the feedback voltage is higher than the reference voltage, the pass transistor gate is driven higher, allowing less current to pass the output. The output voltage is feedback through an internal resistor voltage connected to OUT. Additional blocks include an output current limiter, a thermal sensor and shutdown logic. 6.1 Shutdown Drive SHDN low to place the LD3980 in shutdown mode for DFN versions. In shutdown mode, the pass transistor, control circuit, reference and all biases are turned off, reducing the supply current to typically 0.5µA. Connecting SHDN to IN every block is in normal operation. 6.2 Current limit The device includes short-circuit protection. It includes a current limiter that controls the pass transistor's gate voltage to limit the output current to about 600mA. 6.3 Thermal overload protection The Thermal over load protection limits total power dissipation in the device. When the junction temperature (TJ) exceeds +140°C, the thermal sensor sends a signal to the shutdown logic, turning off the pass transistor and allowing the device to cool. The pass transistor turns on again after the device's junction temperature typically cools by 15°C, resulting in a pulsed output during continuous thermal overload conditions. 6.4 Power dissipation Maximum power dissipation of the LD3980 depends on the thermal resistance of the case and circuit board, the temperature difference between the die junction and ambient air, and the rate of air flow. The power dissipated by the device is: PD = IO (VI - VO) The maximum power dissipation is: PMAX = (TJMAX - TA) / θ JA Where: TJMAX = +150°C 9/16 Detailed description LD3980 TA is the ambient temperature θ JA thermal resistance. The device's pins perform the dual function of providing an electrical connection as well as channeling heat away from the die. Use wide circuit-board traces and large, solid copper polygons to improve power dissipation. Using multiple vias to buried ground planes further enhances thermal conductivity. 6.5 Output capacitance The device is specifically designed to employ ceramic output capacitors as low as 1µF. Ceramic capacitors below 10µF offer significant cost and space savings, along with high frequency noise filtering. Higher values and other types of capacitor may be used, but their equivalent series resistance should be maintained in the range of the table. 10/16 LD3980 7 Package mechanical data Package mechanical data In order to meet environmental requirements, ST offers these devices in ECOPACK® packages. These packages have a Lead-free second level interconnect. The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com. 11/16 Package mechanical data LD3980 DFN6 (3x3) MECHANICAL DATA mm. mils DIM. MIN. TYP MAX. MIN. TYP. MAX. A 0.80 1.00 31.5 39.4 A1 0 0.05 0.0 2.0 A2 0.65 0.75 25.6 29.5 A3 0.20 b 0.33 D 2.90 D2 1.92 E 2.90 E2 1.11 e L 3.00 0.43 13.0 3.10 114.2 2.12 75.6 3.10 114.2 1.31 43.7 0.95 0.20 L1 0.45 118.1 122.0 83.5 118.1 122.0 51.6 7.9 17.7 9.4 0.13 0.20 16.9 37.4 0.24 L2 K 3.00 7.9 5.1 7.9 7387339A 12/16 LD3980 Package mechanical data Tape & Reel QFNxx/DFNxx (3x3) MECHANICAL DATA mm. inch DIM. MIN. TYP A MAX. MIN. TYP. 330 13.2 12.992 C 12.8 D 20.2 0.795 N 60 2.362 T MAX. 0.504 0.519 18.4 0.724 Ao 3.3 0.130 Bo 3.3 0.130 Ko 1.1 0.043 Po 4 0.157 P 8 0.315 13/16 Order code LD3980 8 Order code Table 5. Order code Part number Output voltage (1) LD3980PM08R 0.8 V LD3980PM12R 1.2 V (2) LD3980PM13R 1.3 V (2) LD3980PM135R 1.35 V LD3980PM15R 1.5 V (2) LD3980PM18R 1.8 V LD3980PM30R 3.0 V (2) 1. Other values of VO available on request 2. Available on request 14/16 LD3980 Revision history 9 Revision history Table 6. Revision history Date Revision 05-Dec-2006 1 Changes First release. 15/16 LD3980 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2006 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 16/16