M74HC257 QUAD 2 CHANNEL MULTIPLEXER (3-STATE) ■ ■ ■ ■ ■ ■ ■ HIGH SPEED : tPD = 11 ns (TYP.) at VCC = 6V LOW POWER DISSIPATION: ICC =4µA(MAX.) at TA=25°C HIGH NOISE IMMUNITY: VNIH = V NIL = 28 % VCC (MIN.) SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 6mA (MIN) BALANCED PROPAGATION DELAYS: tPLH ≅ tPHL WIDE OPERATING VOLTAGE RANGE: VCC (OPR) = 2V to 6V PIN AND FUNCTION COMPATIBLE WITH 74 SERIES 257 DESCRIPTION The M74HC257 is an high speed CMOS QUAD 2 CHANNEL MULTIPLEXER (3-STATE) fabricated with silicon gate C2MOS technology. This IC is composed of an independent 2-channel multiplexer with common SELECT and ENABLE (OE) input. The M74HC257 is a non-inverting multiplexer. DIP SOP TSSOP ORDER CODES PACKAGE TUBE DIP SOP TSSOP M74HC257B1R M74HC257M1R T&R M74HC257RM13TR M74HC257TTR When the ENABLE input is held "High", outputs of the IC become in a High-Impedance state. If SELECT input is held low, "A" data is selected, when SELECT is high , "B" data is chosen. All inputs are equipped with protection circuits against static discharge and transient excess voltage. PIN CONNECTION AND IEC LOGIC SYMBOLS August 2001 1/11 M74HC257 INPUT AND OUTPUT EQUIVALENT CIRCUIT PIN DESCRIPTION PIN No SYMBOL 1 SELECT 2, 5, 14, 11 3, 6, 13, 10 1A to 4A 1B to 4B 4, 7, 12, 9 1Y to 4Y 15 OE 8 16 GND Vcc NAME AND FUNCTION Common Data Select Input Data Input From Source A Data Input From Source B 3 State Multiplexer Outputs 3 State Output Enable Inputs (Active Low) Ground (0V) Positive Supply Voltage TRUTH TABLE INPUTS OE SELECT A B Y H L L L L X L L H H X L H X X X X X L H Z L H L H X : Don’t Care Z : High Impedance LOGIC DIAGRAM This logic diagram has not be used to estimate propagation delays 2/11 OUTPUT M74HC257 ABSOLUTE MAXIMUM RATINGS Symbol VCC Parameter Value Supply Voltage Unit -0.5 to +7 V -0.5 to VCC + 0.5 -0.5 to VCC + 0.5 V DC Input Diode Current ± 20 mA IOK DC Output Diode Current ± 20 mA IO DC Output Current ± 35 mA ± 70 mA VI DC Input Voltage VO DC Output Voltage IIK ICC or IGND DC VCC or Ground Current PD Power Dissipation Tstg Storage Temperature TL Lead Temperature (10 sec) V 500(*) mW -65 to +150 °C 300 °C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied (*) 500mW at 65 °C; derate to 300mW by 10mW/°C from 65°C to 85°C RECOMMENDED OPERATING CONDITIONS Symbol VCC Parameter Value Supply Voltage Unit 2 to 6 V VI Input Voltage 0 to VCC V VO Output Voltage 0 to VCC V Top Operating Temperature -55 to 125 °C Input Rise and Fall Time tr, tf VCC = 2.0V 0 to 1000 ns VCC = 4.5V 0 to 500 ns VCC = 6.0V 0 to 400 ns 3/11 M74HC257 DC SPECIFICATIONS Test Condition Symbol VIH VIL VOH VOL II IOZ ICC 4/11 Parameter High Level Input Voltage Low Level Input Voltage High Level Output Voltage Low Level Output Voltage Input Leakage Current High Impedance Output Leakage Current Quiescent Supply Current Value TA = 25°C VCC (V) Min. 2.0 4.5 6.0 2.0 4.5 6.0 Typ. Max. 1.5 3.15 4.2 -40 to 85°C -55 to 125°C Min. Min. Max. 1.5 3.15 4.2 0.5 1.35 1.8 Max. 1.5 3.15 4.2 0.5 1.35 1.8 V 0.5 1.35 1.8 2.0 IO=-20 µA 1.9 2.0 1.9 1.9 4.5 IO=-20 µA 4.4 4.5 4.4 4.4 6.0 IO=-20 µA 5.9 6.0 5.9 5.9 4.5 IO=-6.0 mA 4.18 4.31 4.13 4.10 5.68 Unit V V 6.0 IO=-7.8 mA 2.0 IO=20 µA 0.0 0.1 0.1 0.1 4.5 IO=20 µA 0.0 0.1 0.1 0.1 6.0 IO=20 µA 0.0 0.1 0.1 0.1 4.5 IO=6.0 mA 0.17 0.26 0.33 0.40 6.0 IO=7.8 mA 0.18 0.26 0.33 0.40 6.0 VI = VCC or GND ± 0.1 ±1 ±1 µA 6.0 VI = VIH or VIL VO = VCC or GND ± 0.5 ±5 ± 10 µA 6.0 VI = VCC or GND 4 40 80 µA 5.8 5.63 5.60 V M74HC257 AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6ns) Test Condition Symbol Parameter tTLH tTHL Output Transition Time tPLH tPHL Propagation Delay Time (A, B - Y) tPLH tPHL Propagation Delay Time (SELECT - Y) tPZL tPZH High Impedance Output Enable Time tPLZ tPHZ High Impedance Output Disable Time TA = 25°C VCC (V) 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 Value Min. 50 50 150 50 150 50 RL = 1 KΩ 150 RL = 1 KΩ 50 RL = 1 KΩ Typ. Max. 25 7 6 45 13 11 62 18 15 45 13 11 62 18 15 40 12 10 57 17 14 28 14 13 60 12 10 100 20 17 140 28 24 100 20 17 140 28 24 110 22 19 150 30 26 140 28 24 -40 to 85°C -55 to 125°C Min. Min. Max. 75 15 13 125 25 21 175 35 30 125 25 21 175 35 30 140 28 24 190 38 32 175 35 30 Unit Max. 90 19 15 150 30 26 210 42 36 150 30 26 210 42 36 165 33 28 225 45 38 210 42 36 ns ns ns ns ns ns ns ns CAPACITIVE CHARACTERISTICS Test Condition Symbol Parameter CIN Input Capacitance COUT Output Capacitance Power Dissipation Capacitance (note 1) CPD VCC (V) Value TA = 25°C Min. Typ. Max. 5 10 -40 to 85°C -55 to 125°C Min. Min. Max. 10 Unit Max. 10 pF 10 pF 47 pF 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/4 (per Channel) 5/11 M74HC257 TEST CIRCUIT TEST tPLH, tPHL SWITCH Open tPZL, tPLZ VCC tPZH, tPHZ GND CL = 50pF/150pF or equivalent (includes jig and probe capacitance) R1 = 1KΩ or equivalent RT = ZOUT of pulse generator (typically 50Ω) WAVEFORM 1: PROPAGATION DELAY TIME (f=1MHz; 50% duty cycle) 6/11 M74HC257 WAVEFORM 2 :OUTPUT ENABLE AND DISABLE TIME (f=1MHz; 50% duty cycle) 7/11 M74HC257 Plastic DIP-16 (0.25) MECHANICAL DATA mm. inch DIM. MIN. a1 0.51 B 0.77 TYP MAX. MIN. TYP. MAX. 0.020 1.65 0.030 0.065 b 0.5 0.020 b1 0.25 0.010 D 20 0.787 E 8.5 0.335 e 2.54 0.100 e3 17.78 0.700 F 7.1 0.280 I 5.1 0.201 L Z 3.3 0.130 1.27 0.050 P001C 8/11 M74HC257 SO-16 MECHANICAL DATA DIM. mm. MIN. TYP A a1 inch MAX. MIN. TYP. 1.75 0.1 0.068 0.2 a2 MAX. 0.003 0.007 1.65 0.064 b 0.35 0.46 0.013 0.018 b1 0.19 0.25 0.007 0.010 C 0.5 0.019 c1 45° (typ.) D 9.8 10 0.385 0.393 E 5.8 6.2 0.228 0.244 e 1.27 0.050 e3 8.89 0.350 F 3.8 4.0 0.149 0.157 G 4.6 5.3 0.181 0.208 L 0.5 1.27 0.019 0.050 M S 0.62 0.024 8° (max.) PO13H 9/11 M74HC257 TSSOP16 MECHANICAL DATA mm. inch DIM. MIN. TYP A MAX. MIN. TYP. MAX. 1.2 A1 0.05 A2 0.8 b 0.047 0.15 0.002 0.004 0.006 1.05 0.031 0.039 0.041 0.19 0.30 0.007 0.012 c 0.09 0.20 0.004 0.0089 D 4.9 5 5.1 0.193 0.197 0.201 E 6.2 6.4 6.6 0.244 0.252 0.260 E1 4.3 4.4 4.48 0.169 0.173 0.176 1 e 0.65 BSC K 0° L 0.45 A 0.60 0.0256 BSC 8° 0° 0.75 0.018 8° 0.024 0.030 A2 A1 b e K c L E D E1 PIN 1 IDENTIFICATION 1 0080338D 10/11 M74HC257 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. © The ST logo is a registered trademark of STMicroelectronics © 2001 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom © http://www.st.com 11/11