STV0984 2 MegaPixel SMIA Profile 2 Mobile Imaging Processor DATA BRIEF – Sensor interface: 2x CCP2.0(2) serial receivers (csi class 2 receivers) – Host interface: CCP1.01. serial transmitter (csi class 0 transmitter), ITU, PI – Control interface: I²C Features ■ Supports 2 SMIA profile 2 compliant sensors mutually exclusive up to 2 Megapixel (1600x1200) resolution.(1) ■ Enhanced video processor – Noise/defect filtering, color reconstruction, sharpness enhancement and radial corrections – Statistic processor for exposure and white balance and autofocus control – GPIOs and ADC to control external actuators ■ 2 video pipes for full frame rate concurrent viewfinder and video/still capture. Single shot (e.g. flashgun) thumbnail generation – Gamma correction programmable for both CRT and LCD displays. Color correction matrix – Digital zoom: Smooth downscale capability (independent X/Y characteristics) and upscale capability to 4x ■ SMIA output formats: JPEG, YUV4:2:2, YUV420, RGB888, RGB565, RGB444 ■ 4:2:0 JPEG compression with programmable quantization matrix and target file size ■ JPEG operations up to 30 fps at UXGA resolution ■ Interleaved video modes (concurrent still/video + ViewFinder) – ‘Alternate CCP frame’ mode up to 15 fps – ‘Single CCP frame’ mode up to 30 fps ■ Flash gun control (high power LED mode and white LED mode) Description The STV0984 is a new generation, ultra low power Megapixel digital image processor designed to fit into mobile applications. STV0984 comes with support for 2 SMIA sensor heads and programmable intelligent General Purpose IOs engine to control, through dedicated firmware, external actuators such as flashgun, white led and autofocus solution. STV0984 provides internal buffering capability along with a versatile clock manager to accommodate different data rates between input sensors and host interface. Applications ■ Mobile phone ■ PDA ■ Wireless security camera Ordering information ■ CCP transmitter derating capabilities (by 2,3,4,5 and 6) of sensor high speed clock ■ Interfaces Table 1. Order codes Part number STV0984/TR (Tape and Reel) Description Rohs compliant (Leadfree) TFBGA 84 balls, tape and reel packing 1.SMIA 1.0 functional specification version 1.0. SMIA horizontal/vertical scaling not supported. 2. SMIA 1.0 CCP2 Specification version 1.0 http://www.smia-forum.org/ September 2005 CD00066603 For further information contact your local STMicroelectronics sales office. Rev 1 1/3 www.st.com 3 STV0984 Figure 1. SMIA camera module 1 Application diagram EXTCLK XSHUTDOWN STV0984 2.0 Megapixel CCP 2.0 SMIA Processor CCI SSCL Baseband or Application Processor SSDA Technical specifications Technology 0.13 µm HCMOS 9 Sensor SMIA compliant CMOS sensors up to 2 MegaPixels Frame rate up to 30fps @ 2MP JPEG + QQVGA RGB888l @ VGA YUV422 @ QCIF YUV422+QVGA RGB888 Still digital zoom x4 2MP (x4 upscale) Video/Viewfinder digital zoom if single video mode: x10 VGA; x20 QVGA; (x4 upscale) If interleaved video mode: x8 QVGA RGB565+QCIF YUV422 Power supply 2.8V, 1.8V (I/O ring), 1.2V core logic, +/- 0.1V (Optional 1.2V Internal regulator from 1.8V) Power requirements 2MP JPEG + QQVGA @ 15fps: 120 mA @1.2V ; 15 mA @ 1.8V (+5 mA if internal regulator ON) Standby < 50µW Package Rohs compliant (Leadfree) TFBGA 84 balls 6 x 6 x 1.2 mm ITU / PI CCP1.0 EXTCLK XSHUTDOWN SMIA Table 3. CCP 2.0 camera CCI module 2 Figure 2. Block Diagram TMS[1:0] TCK TDO TDI STV0984 PDN POR RST_DIR SYS_CLK Clock & Power Mgmt JTAG & Test Interface RAM, ROM, µprocessor I2C slave SSCL SSDA SDA ADC_IN ADC I2C Master GPIO Video Processor DATAN SCL PI RAM 128KB ITU CCP 1.0 VC DATAP CCP Receiver (x2) GPIO CLKP CLKN Sensor Interface Internal bus see Table 2 VCLK HCLKP HCLKN HDATAP HDATAN LDO PIEZO GPIO VDD_1V8, 1V2_OUT LDO_STBY LDO_EN Table 2. 2/3 Interface signals ITU signal PI GPIO[13] WR_N Table 4. GPIO[14] RS_N Storage -40 to +150 °C GPIO[15] DREQ Operating -25 to +70 °C ITU[7:0] PI[7:0] HSTYNC RD_N VSYNC CS_N CD00066603 Temperature ranges STV0984 Revision history Date Revision 5-Sept-2005 1 Changes Initial release. Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners © 2005 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com CD00066603 3/3