UNISONIC TECHNOLOGIES CO., LTD M4034 LINEAR INTEGRATED CIRCUIT 3-INPUT VIDEO SWITCH DESCRIPTION The UTC M4034 is 3-input video switch selecting one of three input video or audio signals. Its operating supply voltage range is 5 ~ 12V and bandwidth is 10MHz. Crosstalk is 70dB (at 4.43MHz). FEATURES * Operating Voltage: +4.75V ~ +13V * 3 Input-1 Output * Muting Function available * Wide Operating Supply voltage Range: 4.75V ~ 13V * Cross-talk 70dB (at 4.43MHz) * Muting Function available * Bipolar Technology ORDERING INFORMATION Order Number Lead Free M4034L-D08-T M4034L-G08-T M4034L-S08-R M4034L-S08-T M4034L-SM1-R Halogen Free M4034G-D08-T M4034G-G08-T M4034G-S08-R M4034G-S08-T M4034G-SM1-R www.unisonic.com.tw Copyright © 2011 Unisonic Technologies Co., Ltd Package Packing DIP-8 SIP-8 SOP-8 SOP-8 MSOP-8 Tube Tube Tape Reel Tube Tape Reel 1 of 6 QW-R124-005.Ba M4034 LINEAR INTEGRATED CIRCUIT PIN CONFIGURATION SOP-8/DIP-8/MSOP-8 SIP-8 BLOCK DIAGRAM UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 2 of 6 QW-R124-005.Ba M4034 LINEAR INTEGRATED CIRCUIT ABSOLUTE MAXIMUM RATINGS PARAMETER RATINGS 15 SOP-8 300 DIP-8 500 Power Dissipation PD MSOP-8 250 SIP-8 800 Junction Temperature TJ +125 Operating Temperature TOPR -20 ~ +75 Storage Temperature TSTG -40 ~ +125 Note Absolute maximum ratings are those values beyond which the device could be permanently damaged. Absolute maximum ratings are stress ratings only and functional device operation is not implied. Supply Voltage SYMBOL V+ UNIT V mW mW mW mW ℃ ℃ ℃ ELECTRICAL CHARACTERISTICS (VIN=5V, Ta=25℃) PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX Recommended Supply Voltage V+ 4.75 13.0 Output Offset Voltage VO(OFF) (Note 2) -30 +30 High VCH All inside SW : ON 2.4 Switch Change Voltage All inside SW : OFF 0.8 Low VCL Operating Current ICC S1=S2=S3=S4=S5=1 10.6 14.5 Voltage Gain GV VIN=2.5V, 100kHz, VOUT/VIN -0.5 +0.5 Total Harmonic Distortion THD VINI=2.5V, 1kHz 0.03 Differential Gain DG VIN=2V, Staircase signal 0 Differential Phase DP VIN=2V, Staircase signal 0 Frequency Characteristic (1) Gf1 VIN=2.5V, VOUT(20Hz)/VOUT (100kHz) -1.0 +1.0 Frequency Characteristic (2) Gf2 VIN=2.0V, VOUT(10MHz)/VOUT(100kHz) -1.0 +1.0 Crosstalk (1) CT1 VIN=2.0V, 4.43MHz, VOUT/VIN (Note 3) -70 Crosstalk (2) CT2 VIN=2.0V, 4.43MHz, VOUT/VIN (Note 4) -70 Input Impedance R1 15 Output Impedance ROUT 10 Note 1: If it is not shown about switch condition, it is tested on three conditions below. (a) S1=2, S2=S3=S4=S5=1, (b) S2=S4=2, S1=S3=S5=1, (c) S3=S5=2, S1=S2=1, S4=1, or 2. Note 2: S1=S2=S3=1, Output DC Voltage difference of three mode below. (a) S4=S5=1, (b) S4=2, S5=1 (c) S4=1 or 2, S5=2 Note 3: S5=1, Tested on all combination of S1 to S4 excepted two below. (a) S1=S2, S4=1 (b) S2=S4=2 Note 4: Tested on all combination of S1 to S4 excepted one. (a) S5=2, S3=2 UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw UNIT V mV V V mA dB % % deg dB dB dB dB kΩ Ω 3 of 6 QW-R124-005.Ba M4034 LINEAR INTEGRATED CIRCUIT EQUIVALENT CIRCUIT PIN NO. PIN FUNCTION 1 VIN1 INSIDE EQUIVALENT CIRCUIT SW1 2kΩ 2 13kΩ 200Ω SW1 9kΩ 1.1mA 3 VIN2 SW2 2kΩ 4 13kΩ 200Ω SW2 9kΩ 1.1mA 5 VIN3 (Mute) 6 V+ 200Ω 7 VOUT VOUT 5mA 8 GND UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 4 of 6 QW-R124-005.Ba M4034 LINEAR INTEGRATED CIRCUIT TEST CIRCUIT GND V+ 10μF + 0.01μF VOUT + 8 7 6 5 GND VOUT V+ VIN3 VIN1 SW1 VIN2 + + S1 2 1 VOUT SW2 3 10μF RL 1kΩ 4 10μF + 2 1 220μF S2 2 10μF S3 1 2 1 V1 S4 1 2 S5 1 2 VCON 5V CONNECTION DIAGRAM Terminal Name VIN1 SW1 VIN2 SW2 VIN3 V+ VOUT GND DC Voltage UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 5 of 6 QW-R124-005.Ba M4034 LINEAR INTEGRATED CIRCUIT TYPICAL APPLICATION CIRCUIT Oscillation Prevention on light loading conditions Recommended under circuit r r 100Ω C 20pF VOUT 7 C LPF Note: 0.1uF capacitor is required between INPUT and GND for bias type input at mute mode. Input C 0.1μF C UTC assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all UTC products described or contained herein. UTC products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 6 of 6 QW-R124-005.Ba