TX-7030-EAP-1470-20M000 TCXO Nominal frequency (f0) 20 MHz Frequency stabilities Parameter Over all (df/f0) vs. operating temp. range (df/f@25 °C) Frequency stability Operating temp. range -4.6 to 4.6 ppm -0.14 to 0.14 ppm 0 ... 50 °C Value Condition Parameter initial tolerance (df/f0) -1 to 1 ppm @25 °C vs. supply voltage change (df/f) -0.2 to 0.2 ppm static; 3.3 V ±5 % vs. load change (df/f) -0.1 to 0.1 ppm static; Load ± 5 % vs. aging / 20 years (df/f) <± 2.5 ppm @ 40 °C Holdover 24 h ± 0.37 ppm over 24 hours Stratum 3 per GR-1244-CORE: <±4.6ppm for all causes @ 20 years aging incl. hold over RF output Parameter Value Signal Load Fan out Rise Time Fall Time Duty cycle V Low V High LVCMOS 15 pF ±10 % 3 < 5 ns < 5 ns 40 / 60 % x < 0.3 V x>3V Condition @ 10 to 90 %Vout @ 90 to 10 %Vout @ 1.65 V Supply voltage Parameter Supply voltage (Vs) Current consumption steady state Value Condition 3.3 V ± 5 % < 6 mA @ Vsnom & 25 °C Additional Parameters Parameter Typ. Max. Condition Additional information This SMD oscillator is designed only for pick and place/reflow soldering process. Manual soldering may damage the part and therefore not recommended for the mounting of this oscillator. Processing & Packing handling&processing note Additional environmental conditions Sealing test A nicht dicht (not hermetically sealed) Solderability DIN IEC 68 T2-20 (Ta) 100% RoHS 6 compliant Solvent resistance EN 60068-2-45, Test xA washable device Absolute Maximum Ratings Parameter Supply voltage (Vs) Operable temperature range Storage temperature range Min -40 -55 Vectron International • Product Specifications TX-7030-EAP-1470 www.vectron.com Typ Max Units 6 85 125 V °C °C modified 2011-03-29 Index : 1 Condition printed 2011-06-03 • page 1 of 4 TX-7030-EAP-1470-20M000 TCXO Enclosure Type G298 Height 1.8 mm all units in mm Pin Connections Pin 1: N.C. Pin 2: GND(Case) Pin 3: RF-Output Pin 4: Vs (supply voltage) Marking EAP1470 20M000 *VAYYWW * pin-1 marking Vectron International • Product Specifications TX-7030-EAP-1470 www.vectron.com modified 2011-03-29 Index : 1 printed 2011-06-03 • page 2 of 4 TX-7030-EAP-1470-20M000 TCXO Reflow profile Profile Feature Pb-Free Assembly/Sn-Pb Assembly Average ramp-up rate (TL to Tp) 3°C/second max. Preheat -Temperature Min (Tsmin) 150°c -Temperature Min (Tsmax) 200°c -Time (min to max) (ts) 60-180 seconds Tsmax to TL - Ramp-up Rate 3°C/second max. Time maintainted above - Temperature (TL) 217°C - Time (tL) 60-150 seconds Peak Temperature (Tp) max 260°C Time within 5°C of actual Peak Temperature (tp) 20-40 seconds Ramp-down Rate 6°C/second max. Time 25°C to Peak Temperature 8 minutes max. Note: All temperatures refer to topside of the package, measured on the package body surface. Additional Information This SMD oscillator has been designed for pick and place reflow soldering. Vectron International • Product Specifications TX-7030-EAP-1470 www.vectron.com modified 2011-03-29 Index : 1 printed 2011-06-03 • page 3 of 4 TX-7030-EAP-1470-20M000 TCXO Standard shipping method Tape width W [mm] Quantity per meter Quantity per reel P [mm] A [mm] B [mm] K [mm] 16 125 750 8 5.4 7.4 2.7 Notes: Unless otherwise stated all values are valid after warm-up time and refer to typical conditions for supply voltage, frequency control voltage, load, temperature (25°C). Subject to technical modification. Vectron International • Product Specifications TX-7030-EAP-1470 www.vectron.com modified 2011-03-29 Index : 1 printed 2011-06-03 • page 4 of 4