VX-401-DUAL Voltage Controlled Crystal Oscillator VX-401 Features Applications • AT-Cut Crystal • Surface Mount FR4 based package • Reflow Process Compatible • Low Phase Noise • Tight Stabilities • Frequency Range 100 - 800MHz • Standard Frequencies 100; 112; 122.88; 125; 134.4; 153.6; 155.52; • 160; 179.2; 184.32; 245.76; 307.2; 312.5; • 320; 368.64; 400; 448; 471.8592; 491.52; • 622.08; 672; 737.28; 800MHz • Previous Model Number: C5430 • Base Stations • Test Equipment • Synthesizers • Switching • Military Performance Specifications Frequency Stabilities1 Parameter Min vs. operating temperature range (referenced to +25°C) Initial tolerance vs. supply voltage change vs. load change vs. aging / 1 Year vs. aging (following years) Typical Max Units Condition -30 +30 ppm -40 to +85°C -15 -3 -2 -3 -1 +15 +3 +2 +3 +1 ppm ppm ppm ppm ppm @Vc=Vs/2 VS ±5% Load ±10% Page 1 of 5 Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Performance Specifications Supply Voltage (Vs) Min Typical Max Units 3.135 3.3 3.465 VDC 90 mA 5.25 VDC 80 mA Current consumption Supply voltage 4.75 5 Current consumption Condition @ PECL, LVDS Options Parameter Supply voltage (standard) @ PECL, LVDS RF Output PECL Load 50 Ω Rise and Fall time Duty cycle 45 Signal 1 ns 55 % 1 ns 60 % 20 to 80% Options Signal LVDS Load 100 Ω Rise and Fall time Duty cycle 40 10 to 90% Frequency Tuning (EFC) Tuning Range ±75.0 ±90 Linearity ±200.0 10 % Tuning Slope Positive Control Voltage Range 0 0.5 Frequency Control Input Impedance 10 1.65 2.5 3.3 4.5 VDC VDC with Vs = 3.3V with Vs = 5V kΩ Additional Parameters Phase Noise Jitter Phase Noise Jitter -77 -111 -139 -145 -146 0.24 dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz ps RMS 10 Hz 100 Hz 1 kHz 10 kHz 100 kHz @ 12kHz .. 20MHz @ 160 MHz LVPECL 3.3V -62 -93 -119 -140 -148 0.07 dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz ps RMS 10 Hz 100 Hz 1 kHz 10 kHz 100 kHz @ 12kHz .. 20MHz @ 448 MHz LVPECL 3.3V Page 2 of 5 Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Performance Specifications Additional Parameters Subharmonics -40 Weight dBc 2.0 g Processing & Packing Handling & Processing Note Absolute Maximum Ratings Supply voltage (Vs) 6.0 V Operable Temperature Range -40 +85 °C Storage Temperature Range -55 +125 °C Cross Reference Typical CrossPhase Reference NoiseList List and Jitter Phase Noise Phase Noise VX-401 @ 166.628571 MHz LVPECL VX-401 @ 160 MHz LVPECL Phase Noise VX-401 @ 448 MHz LVPECL Page 3 of 5 Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Enclosure Package Codes Type Height “H” Pin Length “L” G212 5.9 NA Marking VX-401-xxxx Frequency 1 / Frequency 2 AYYWW Pin Connections Enable true table 1 Control Voltage (Vc) LVPECL / LVDS 2 Frequency Select Low: Frequency 1 / High: Frequency 2 Pin 6 Pin 8 6 Enable High No Data No Data 7 GND Open Data Compl. Data 8 RF Output Low Data Compl. Data 9 RF Output complementary 14 Supply Voltage Input (Vs) Pin 9 Page 4 of 5 Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Standard Shipping Method Lage im Gurt Position in tape Pin 1 A Abwickelrichtung Unwinding direction X B P Gurtunterseite Tape buttom side K Gurtoberseite Tape upper side *bei W ≤ 24 mm nur untere Lochreihe ∗by W ≤ 24 mm only lower hole line Enclosure Type Tape Width W (mm) G218B/G223B 24 Quantity per meter Quantity per reel Dimension P 500 12 Recommended Reflow Profile Profile Feature Pb-Free Assembly/ Sn-Pb Assembly Profile Feature Pb-Free Assembly/ Sn-Pb Assembly Average ramp-up rate (TL to TP) 3°C/second max. Time 25°C to Peak Temperature 8 minutes max. 150°C 200°C 60-180 seconds Time maintained above -Temperature (TL) -Time (tL) 217°C 60-150 seconds Preheat -Temperature Min TSmin -Temperature Min TSmax -Time (min to max) tS TSmax to TL -Ramp-up Rate 3°C/second max Time maintained above -Temperature (TL) -Time (tL) 217°C 60-150 seconds Time within 5°C of actual Peak Temperature (tP) 20-40 seconds Peak Temperature (TP) max 260°C Ramp-down Rate 6°C/ second max Note: All temperatures refer to topside of the package, measured on the package body surface. Page 5 of 5 Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Ordering Information VX-401 0 - E A E - 305 0 - 122M880 - 153M600 Model Code Frequency 2 Height 0: 5.9 mm (G223B) Frequency 1 Supply Voltage D: 5V E: 3.3V RF Output Code Stability Code E-305: ±30ppm Enable 0: No Enable 1: Enable Temperature Range E: -40°C to +85°C C: PECL D: LVDS Notes: 1. Contact factory for improved stabilities or additional product options. Not all options and codes are available at all frequencies. 2. Unless other stated all values are valid after warm-up time and refer to typical conditions for supply voltage, frequency control voltage, load, temperature (25°C). 3. Phase noise degrades with increasing output frequency. 4. Subject to technical modification. 5. Contact factory for availability. For Additional Information, Please Contact USA: Vectron International 267 Lowell Road Hudson, NH 03051 Tel: 1.888.328.7661 Fax: 1.888.329.8328 Europe: Vectron International Landstrasse, D-74924 Neckarbischofsheim, Germany Tel: +49 (0) 7268-801-0 Fax: +49 (0) 7268-801-281 Asia: Vectron International 1F-2F, No 8 Workshop, No 308 Fenju Road WaiGaoQiao Free Trade Zone Pudong, Shanghai, China 200131 Tel: 86.21.5048.0777 Fax: 86.21.5048.1881 Disclaimer Vectron International reserves the right to make changes to the product(s) and or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Rev: 10/2011 Page 6 of 5 Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com