ATMEL AT27BV040

Features
• Fast Read Access Time – 120 ns
• Dual Voltage Range Operation
•
•
•
•
•
•
•
•
•
– Unregulated Battery Power Supply Range, 2.7V to 3.6V
or Standard 5V ± 10% Supply Range
Compatible with JEDEC Standard AT27C040
Low Power CMOS Operation
– 20 µA Max (Less than 1 µA Typical) Standby for VCC = 3.6V
– 36 mW Max Active at 5 MHz for VCC = 3.6V
JEDEC Standard Packages
– 32-lead PLCC
– 32-lead TSOP
– 32-lead VSOP
High Reliability CMOS Technology
– 2,000V ESD Protection
– 200 mA Latchup Immunity
Rapid Programming Algorithm – 100 µs/Byte (Typical)
CMOS and TTL Compatible Inputs and Outputs
– JEDEC Standard for LVTTL and LVBO
Integrated Product Identification Code
Industrial Temperature Range
Green (Pb/Halide-free/RoHS Compliant) Packaging
4-Megabit
(512K x 8)
Unregulated
Battery-Voltage
High-Speed
OTP EPROM
AT27BV040
1. Description
The AT27BV040 chip is a high performance, low power, low voltage, 4,194,304-bit
one-time programmable read only memory (EPROM) organized as 512K by 8 bits. It
requires only one supply in the range of 2.7 to 3.6V in normal read mode operation,
making it ideal for fast, portable systems using either regulated or unregulated battery
power.
Atmel’s innovative design techniques provide fast speeds that rival 5V parts while
keeping the low power consumption of a 3V supply. At VCC = 2.7V, any byte can be
accessed in less than 100 ns. With a typical power dissipation of only 18 mW at 5 MHz
and VCC = 3V, the AT27BV040 consumes less than one fifth the power of a standard
5V EPROM. Standby mode supply current is typically less than 1 µA at 3V. The
AT27BV040 simplifies system design and stretches battery lifetime even further by
eliminating the need for power supply regulation.
The AT27BV040 is available in industry-standard JEDEC-approved one-time programmable (OTP) plastic PLCC, TSOP, and VSOP packages. All devices feature twoline control (CE, OE) to give designers the flexibility to prevent bus contention.
The AT27BV040 operating with VCC at 3.0V produces TTL level outputs that are compatible with standard TTL logic devices operating at VCC = 5.0V. At VCC = 2.7V, the
part is compatible with JEDEC approved low voltage battery operation (LVBO) interface specifications. The device is also capable of standard 5-volt operation making it
ideally suited for dual supply range systems or card products that are pluggable in
both 3-volt and 5-volt hosts.
0346G–EPROM–12/07
Atmel’s AT27BV040 has additional features to ensure high quality and efficient production use.
The Rapid Programming Algorithm reduces the time required to program the part and guarantees reliable programming. Programming time is typically only 100 µs/byte. The Integrated
Product Identification Code electronically identifies the device and manufacturer. This feature is
used by industry-standard programming equipment to select the proper programming algorithms
and voltages. The AT27BV040 programs exactly the same way as a standard 5V AT27C040
and uses the same programming equipment.
2. Pin Configurations
Function
A0 - A18
Addresses
O0 - O7
Outputs
CE
Chip Enable
OE
Output Enable
32-lead PLCC Top View
29
28
27
26
25
24
23
22
21
14
15
16
17
18
19
20
5
6
7
8
9
10
11
12
13
A14
A13
A8
A9
A11
OE
A10
CE
O7
O1
O2
GND
O3
O4
O5
O6
A7
A6
A5
A4
A3
A2
A1
A0
O0
4
3
2
1
32
31
30
A12
A15
A16
VPP
VCC
A18
A17
2.1
Pin Name
2.2
32-lead TSOP, VSOP Top View – Type 1
A11
A9
A8
A13
A14
A17
A18
VCC
VPP
A16
A15
A12
A7
A6
A5
A4
2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
OE
A10
CE
O7
O6
O5
O4
O3
GND
O2
O1
O0
A0
A1
A2
A3
AT27BV040
0346G–EPROM–12/07
AT27BV040
3. Switching Considerations
Switching between active and standby conditions via the Chip Enable pin may produce transient
voltage excursions. Unless accommodated by the system design, these transients may exceed
datasheet limits, resulting in device non-conformance. At a minimum, a 0.1 µF high frequency,
low inherent inductance, ceramic capacitor should be utilized for each device. This capacitor
should be connected between the VCC and Ground terminals of the device, as close to the
device as possible. Additionally, to stabilize the supply voltage level on printed circuit boards
with large EPROM arrays, a 4.7 µF bulk electrolytic capacitor should be utilized, again connected between the VCC and Ground terminals. This capacitor should be positioned as close as
possible to the point where the power supply is connected to the array.
4. Block Diagram
5. Absolute Maximum Ratings*
Temperature Under Bias.................................. -40°C to +85°C
Storage Temperature ..................................... -65°C to +125°C
Voltage on Any Pin with
Respect to Ground .........................................-2.0V to +7.0V(1)
Voltage on A9 with
Respect to Ground ......................................-2.0V to +14.0V(1)
*NOTICE:
Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and
functional operation of the device at these or any
other conditions beyond those indicated in the
operational sections of this specification is not
implied. Exposure to absolute maximum rating
conditions for extended periods may affect device
reliability
VPP Supply Voltage with
Respect to Ground .......................................-2.0V to +14.0V(1)
Note:
1. Minimum voltage is -0.6V DC which may undershoot to -2.0V for pulses of less than 20 ns. Maximum output pin voltage is
VCC + 0.75V DC which may be exceeded if certain precautions are observed (consult application notes) and which may
overshoot to +7.0V for pulses of less than 20 ns.
3
0346G–EPROM–12/07
6. Operating Modes
Mode/Pin
CE
OE
Ai
VPP
VCC
Outputs
Read(2)
VIL
VIL
Ai
X(1)
VCC(2)
DOUT
Output Disable
Standby
(2)
(2)
Rapid Program(3)
(3)
PGM Verify
(3)
PGM Inhibit
X
VIH
X
X
VCC
(2)
High Z
VCC
(2)
High Z
VIH
X
X
X
VIL
VIH
Ai
VPP
VCC(3)
VPP
VCC
(3)
DOUT
VCC
(3)
High Z
X
VIH
VIL
VIH
Ai
X
VPP
DIN
(4)
Product Identification(3)(5)
Notes:
VIL
VIL
A9 = VH
A0 = VIH or VIL
A1 - A18 = VIL
VCC(3)
X
Identification Code
1. X can be VIL or VIH.
2. Read, output disable, and standby modes require, 2.7V ≤VCC ≤3.6V, or 4.5V ≤VCC ≤5.5V.
3. Refer to Programming Characteristics. Programming modes require VCC = 6.5V.
4. VH = 12.0 ± 0.5V.
5. Two identifier bytes may be selected. All Ai inputs are held low (VIL), except A9 which is set to VH and A0 which is toggled
low (VIL) to select the Manufacturer’s Identification byte and high (VIH) to select the Device Code byte.
7. DC and AC Operating Conditions for Read Operation
AT27BV040-12
Industrial Operating Temperature (Case)
-40°C - 85°C
2.7V to 3.6V
VCC Power Supply
4
5V ± 10%
AT27BV040
0346G–EPROM–12/07
AT27BV040
8. DC and Operating Characteristics for Read Operation
Symbol
Parameter
Condition
Min
Max
Units
VCC = 2.7V to 3.6V
ILI
Input Load Current
VIN = 0V to VCC
±1
µA
ILO
Output Leakage Current
VOUT = 0V to VCC
±5
µA
IPP1(2)
VPP(1) Read/Standby Current
VPP = VCC
10
µA
VCC(1) Standby Current
ISB1 (CMOS), CE = VCC ± 0.3V
20
µA
ISB
ISB2 (TTL), CE = 2.0 to VCC + 0.5V
100
µA
ICC
VCC Active Current
f = 5 MHz, IOUT = 0 mA, CE = VIL,
VCC = 3.6V
10
mA
VIL
Input Low Voltage
VIH
Input High Voltage
VOL
VOH
Output Low Voltage
Output High Voltage
VCC = 3.0 to 3.6V
-0.6
0.8
V
VCC = 2.7 to 3.6V
-0.6
0.2 x VCC
V
VCC = 3.0 to 3.6V
2.0
VCC + 0.5
V
VCC = 2.7 to 3.6V
0.7 x VCC
VCC + 0.5
V
IOL = 2.0 mA
0.4
V
IOL = 100 µA
0.2
V
IOL = 20 µA
0.1
V
IOH = -2.0 mA
2.4
V
IOH = -100 µA
VCC - 0.2
V
IOH = -20 µA
VCC - 0.1
V
VCC = 4.5V to 5.5V
ILI
Input Load Current
VIN = 0V to VCC
±1
µA
ILO
Output Leakage Current
VOUT = 0V to VCC
±5
µA
IPP1(2)
VPP(1) Read/Standby Current
VPP = VCC
10
µA
VCC(1) Standby Current
ISB1 (CMOS), CE = VCC ± 0.3V
100
µA
ISB
ISB2 (TTL), CE = 2.0 to VCC + 0.5V
1
mA
ICC
VCC Active Current
f = 5 MHz, IOUT = 0 mA, CE = VIL
30
mA
VIL
Input Low Voltage
-0.6
0.8
V
VIH
Input High Voltage
2.0
VCC + 0.5
V
VOL
Output Low Voltage
IOL = 2.1 mA
0.4
V
VOH
Output High Voltage
IOH = -400 µA
Notes:
2.4
V
1. VCC must be applied simultaneously with or before VPP, and removed simultaneously with or after VPP.
2. VPP may be connected directly to VCC, except during programming. The supply current would then be the sum of ICC and IPP.
5
0346G–EPROM–12/07
9. AC Characteristics for Read Operation
VCC = 2.7V to 3.6V and 4.5V to 5.5V
AT27BV040-12
Symbol
Parameter
Condition
Address to Output Delay
tCE(2)
tOE(2)(3)
tDF(4)(5)
OE or CE High to Output Float, Whichever
Occurred First
tOH
Output Hold from Address, CE or OE, Whichever
Occurred First
tACC
(3)
Min
Max
Units
CE = OE = VIL
120
ns
CE to Output Delay
OE = VIL
120
ns
OE to Output Delay
CE = VIL
50
ns
40
ns
0
ns
10. AC Waveforms for Read Operation(1)
Notes:
1. Timing measurement references are 0.8V and 2.0V. Input AC drive levels are 0.45V and 2.4V, unless otherwise specified.
2. OE may be delayed up to tCE - tOE after the falling edge of CE without impact on tCE.
3. OE may be delayed up to tACC - tOE after the address is valid without impact on tACC.
4. This parameter is only sampled and is not 100% tested.
5. Output float is defined as the point when data is no longer driven.
6
AT27BV040
0346G–EPROM–12/07
AT27BV040
11. Input Test Waveforms and Measurement Levels
tR, tF < 20 ns (10% to 90%)
12. Output Test Load
Note: CL = 100 pF including
jig capacitance.
13. Pin Capacitance
f = 1 MHz, T = 25°C(1)
Symbol
CIN
COUT
Note:
Typ
Max
Units
Conditions
4
8
pF
VIN = 0V
8
12
pF
VOUT = 0V
1. Typical values for nominal supply voltage. This parameter is only sampled and is not 100% tested.
7
0346G–EPROM–12/07
14. Programming Waveforms(1)
Notes:
1. The Input Timing Reference is 0.8V for VIL and 2.0V for VIH.
2. tOE and tDFP are characteristics of the device but must be accommodated by the programmer.
3. When programming the AT27BV040 a 0.1 µF capacitor is required across VPP and ground to suppress spurious voltage
transients.
15. DC Programming Characteristics
TA = 25 ± 5°C, VCC = 6.5 ± 0.25V, VPP = 13.0 ± 0.25V
Limits
Symbol
Parameter
Test Conditions
ILI
Input Load Current
VIN = VIL, VIH
VIL
Input Low Level
VIH
Input High Level
VOL
Output Low Voltage
IOL = 2.1 mA
VOH
Output High Voltage
IOH = -400 µA
ICC2
VCC Supply Current (Program and Verify)
IPP2
VPP Supply Current
VID
A9 Product Identification Voltage
8
Min
Max
Units
±10
µA
-0.6
0.8
V
2.0
VCC + 0.7
V
0.4
V
2.4
CE = VIL
11.5
V
40
mA
20
mA
12.5
V
AT27BV040
0346G–EPROM–12/07
AT27BV040
16. AC Programming Characteristics
TA = 25 ± 5°C, VCC = 6.5 ± 0.25V, VPP = 13.0 ± 0.25V
Limits
Test Conditions(1)
Symbol
Parameter
tAS
Address Setup Time
tOES
OE Setup Time
tDS
Data Setup Time
tAH
Address Hold Time
Input Rise and Fall Times:
(10% to 90%) 20 ns
Input Pulse Levels:
Data Hold Time
tDH
tDFP
OE High to Output Float Delay
tVPS
VPP Setup Time
tVCS
VCC Setup Time
tPW
CE Program Pulse Width(3)
0.45V to 2.4V
(2)
Output Timing Reference Level:
0.8V to 2.0V
(2)
Data Valid from OE
tPRT
VPP Pulse Rise Time During
Programming
Max
Units
2
µs
2
µs
2
µs
0
µs
2
µs
0
Input Timing Reference Level:
0.8V to 2.0V
tOE
Notes:
Min
130
ns
2
µs
2
µs
95
105
µs
150
ns
50
ns
1. VCC must be applied simultaneously or before VPP and removed simultaneously or after VPP.
2. This parameter is only sampled and is not 100% tested. Output Float is defined as the point where data is no longer driven –
see timing diagram.
3. Program Pulse width tolerance is 100 µsec ± 5%.
17. Atmel’s AT27BV040 Integrated Product Identification Code(1)
Pins
A0
O7
O6
O5
O4
O3
O2
O1
O0
Hex
Data
Manufacturer
0
0
0
0
1
1
1
1
0
1E
Device Type
1
0
0
0
0
1
0
1
1
0B
Codes
Note:
1. The AT27BV040 has the same Product Identification Code as the AT27C040. Both are programming compatible.
9
0346G–EPROM–12/07
18. Rapid Programming Algorithm
A 100 µs CE pulse width is used to program. The address is set to the first location. VCC is raised
to 6.5V and VPP is raised to 13.0V. Each address is first programmed with one 100 µs CE pulse
without verification. Then a verification/reprogramming loop is executed for each address. In the
event a byte fails to pass verification, up to 10 successive 100 µs pulses are applied with a verification after each pulse. If the byte fails to verify after 10 pulses have been applied, the part is
considered failed. After the byte verifies properly, the next address is selected until all have been
checked. VPP is then lowered to 5.0V and VCC to 5.0V. All bytes are read again and compared
with the original data to determine if the device passes or fails.
10
AT27BV040
0346G–EPROM–12/07
AT27BV040
19. Ordering Information
19.1
Standard Package
ICC (mA)
VCC = 3.6V
tACC
(ns)
Active
Standby
120
8
0.02
Note:
19.2
Package
AT27BV040-12JI
AT27BV040-12TI
AT27BV040-12VI
32J
32T
32V(1)
Operation Range
Industrial
(-40°C to 85°C)
Not recommended for new designs. Use Green package option.
Green Package (Pb/Halide-free/RoHS Compliant)
ICC (mA)
VCC = 3.6V
tACC
(ns)
Active
Standby
120
8
0.02
Note:
Ordering Code
Ordering Code
Package
AT27BV040-12JU
AT27BV040-12TU
32J
32T
Operation Range
Industrial
(-40°C to 85°C)
1. The 32-lead VSOP package is not recommended for new designs.
Package Type
32J
32-Lead, Plastic J-Leaded Chip Carrier (PLCC)
32T
32-Lead, Plastic Thin Small Outline Package (TSOP) (8 x 20 mm)
32V
32-Lead, Plastic Thin Small Outline Package (TSOP) (8 x 14 mm)
11
0346G–EPROM–12/07
20. Packaging Information
20.1
32J – PLCC
1.14(0.045) X 45˚
PIN NO. 1
IDENTIFIER
1.14(0.045) X 45˚
0.318(0.0125)
0.191(0.0075)
E1
E2
B1
E
B
e
A2
D1
A1
D
A
0.51(0.020)MAX
45˚ MAX (3X)
COMMON DIMENSIONS
(Unit of Measure = mm)
D2
Notes:
1. This package conforms to JEDEC reference MS-016, Variation AE.
2. Dimensions D1 and E1 do not include mold protrusion.
Allowable protrusion is .010"(0.254 mm) per side. Dimension D1
and E1 include mold mismatch and are measured at the extreme
material condition at the upper or lower parting line.
3. Lead coplanarity is 0.004" (0.102 mm) maximum.
SYMBOL
MIN
NOM
MAX
A
3.175
–
3.556
A1
1.524
–
2.413
A2
0.381
–
–
D
12.319
–
12.573
D1
11.354
–
11.506
D2
9.906
–
10.922
E
14.859
–
15.113
E1
13.894
–
14.046
E2
12.471
–
13.487
B
0.660
–
0.813
B1
0.330
–
0.533
e
NOTE
Note 2
Note 2
1.270 TYP
10/04/01
R
12
2325 Orchard Parkway
San Jose, CA 95131
TITLE
32J, 32-lead, Plastic J-leaded Chip Carrier (PLCC)
DRAWING NO.
REV.
32J
B
AT27BV040
0346G–EPROM–12/07
AT27BV040
20.2
32T – TSOP
PIN 1
0º ~ 8º
c
Pin 1 Identifier
D1 D
L
b
e
L1
A2
E
A
GAGE PLANE
SEATING PLANE
COMMON DIMENSIONS
(Unit of Measure = mm)
A1
MIN
NOM
MAX
A
–
–
1.20
A1
0.05
–
0.15
A2
0.95
1.00
1.05
D
19.80
20.00
20.20
D1
18.30
18.40
18.50
Note 2
E
7.90
8.00
8.10
Note 2
L
0.50
0.60
0.70
SYMBOL
Notes:
1. This package conforms to JEDEC reference MO-142, Variation BD.
2. Dimensions D1 and E do not include mold protrusion. Allowable
protrusion on E is 0.15 mm per side and on D1 is 0.25 mm per side.
3. Lead coplanarity is 0.10 mm maximum.
L1
0.25 BASIC
b
0.17
0.22
0.27
c
0.10
–
0.21
e
NOTE
0.50 BASIC
10/18/01
R
2325 Orchard Parkway
San Jose, CA 95131
TITLE
32T, 32-lead (8 x 20 mm Package) Plastic Thin Small Outline
Package, Type I (TSOP)
DRAWING NO.
REV.
32T
B
13
0346G–EPROM–12/07
20.3
32V – VSOP
PIN 1
0º ~ 8º
c
Pin 1 Identifier
D1 D
L
b
e
L1
A2
E
A
GAGE PLANE
SEATING PLANE
COMMON DIMENSIONS
(Unit of Measure = mm)
A1
MIN
NOM
MAX
A
–
–
1.20
A1
0.05
–
0.15
A2
0.95
1.00
1.05
D
13.80
14.00
14.20
D1
12.30
12.40
12.50
Note 2
E
7.90
8.00
8.10
Note 2
L
0.50
0.60
0.70
SYMBOL
Notes:
1. This package conforms to JEDEC reference MO-142, Variation BA.
2. Dimensions D1 and E do not include mold protrusion. Allowable
protrusion on E is 0.15 mm per side and on D1 is 0.25 mm per side.
3. Lead coplanarity is 0.10 mm maximum.
L1
0.25 BASIC
b
0.17
0.22
0.27
c
0.10
–
0.21
e
NOTE
0.50 BASIC
10/18/01
R
14
2325 Orchard Parkway
San Jose, CA 95131
TITLE
32V, 32-lead (8 x 14 mm Package) Plastic Thin Small Outline
Package, Type I (VSOP)
DRAWING NO.
REV.
32V
B
AT27BV040
0346G–EPROM–12/07
Headquarters
International
Atmel Corporation
2325 Orchard Parkway
San Jose, CA 95131
USA
Tel: 1(408) 441-0311
Fax: 1(408) 487-2600
Atmel Asia
Room 1219
Chinachem Golden Plaza
77 Mody Road Tsimshatsui
East Kowloon
Hong Kong
Tel: (852) 2721-9778
Fax: (852) 2722-1369
Atmel Europe
Le Krebs
8, Rue Jean-Pierre Timbaud
BP 309
78054 Saint-Quentin-enYvelines Cedex
France
Tel: (33) 1-30-60-70-00
Fax: (33) 1-30-60-71-11
Atmel Japan
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
Japan
Tel: (81) 3-3523-3551
Fax: (81) 3-3523-7581
Technical Support
[email protected]
Sales Contact
www.atmel.com/contacts
Product Contact
Web Site
www.atmel.com
Literature Requests
www.atmel.com/literature
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any
intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY
WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF
THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no
representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications
and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided
otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use
as components in applications intended to support or sustain life.
© 2007 Atmel Corporation. All rights reserved. Atmel®, logo and combinations thereof, and others are registered trademarks or trademarks of
Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.
0346G–EPROM–12/07