RGP20A - RGP20J FAST RECOVERY RECTIFIERS D2A PRV : 50 - 600 Volts Io : 2.0 Amperes FEATURES : * * * * * * 1.00 (25.4) MIN. 0.161 (4.1) 0.154 (3.9) High current capability High reliability Low reverse current Low forward voltage drop Fast switching for high efficiency Pb / RoHS Free 0.284 (7.2) 0.268 (6.8) MECHANICAL DATA : 1.00 (25.4) MIN. 0.040 (1.02) 0.0385 (0.98) * Case : D2A Molded plastic * Epoxy : UL94V-O rate flame retardant * Lead : Axial lead solderable per MIL-STD-202, Method 208 guaranteed * Polarity : Color band denotes cathode end * Mounting position : Any * Weight : 0.645 gram Dimensions in inches and ( millimeters ) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. SYMBOL RGP 20A RGP 20B RGP 20D RGP 20G RGP 20J UNIT Maximum Recurrent Peak Reverse Voltage V RRM 50 100 200 400 600 V Maximum RMS Voltage V RMS 35 70 140 280 420 V V DC 50 100 200 400 600 V RATING Maximum DC Blocking Voltage Maximum Average Forward Current 0.375"(9.5mm) Lead Length Ta = 55 °C Peak Forward Surge Current, 8.3ms Single half sine wave IF(AV) 2.0 A IFSM 80 A VF 1.3 V IR 5.0 µA IR(H) 100 Superimposed on rated load (JEDEC Method) Maximum Peak Forward Voltage at IF = 2.0 A Maximum DC Reverse Current Ta = 25 ° C at Rated DC Blocking Voltage Ta = 150 ° C Trr Typical Junction Capacitance ( Note 2 ) CJ 35 pf R θ JA 22 °C/W Junction Temperature Range TJ - 65 to + 175 °C Storage Temperature Range T STG - 65 to + 175 °C Typical Thermal Resistance ( Note 3 ) 150 µA Maximum Reverse Recovery Time ( Note 1 ) 250 ns Notes : ( 1 ) Reverse Recovery Test Conditions : IF = 0.5 A, IR = 1.0 A, Irr = 0.25 A. ( 2 ) Measured at 1.0 MHz and applied reverse voltage of 4.0 V DC ( 3 ) Thermal Resistance from Junction to Ambient at 0.375" (9.5mm) Lead Lengths, P.C. Board Mounted. Page 1 of 2 Rev. 02 : March 25, 2005 RATING AND CHARACTERISTIC CURVES ( RGP20A - RGP20J ) FIG.1 - REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50 Ω Trr 10 Ω + 0.5 D.U.T. + 0 PULSE GENERATOR ( NOTE 2 ) 50 Vdc (approx .) 1Ω - 0.25 OSCILLOSCOPE ( NOTE 1 ) - 1.0 A SET TIME BASE FOR 50/100 ns/cm NOTES : 1. Rise Time = 7 ns max., Input Impedance = 1 megaohm, 22 pF. 1 2. Rise time = 10 ns max., Source Impedance = 50 ohms. 3. All Resistors = Non-inductive Types. FIG.2 - DERATING CURVE FOR OUTPUT RECTIFIED CURRENT FIG.3 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 100 PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD OUTPUT CURRENT, AMPERES 2.0 1.6 1.2 0.8 0.4 60Hz RESISTIVE OR INDUCTIVE LOAD 0.375" (9.5mm) LEAD LENGTHS 0 0 25 50 75 100 125 80 60 40 8.3 ms SINGLE HALF SINE-WAVE (JEDEC) METHOD 20 TJ = 50 °C 150 0 175 1 AMBIENT TEMPERATURE, ( °C) Pulse W idth = 300 µs 2% Duty Cycle TJ = 25 °C 1.0 0.1 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 FORWARD VOLTAGE, VOLTS Page 2 of 2 6 10 20 40 60 100 1.8 2.0 FIG.5 - TYPICAL REVERSE CHARACTERISTICS REVERSE CURRENT, MICROAMPERES FORWARD CURRENT, AMPERES 10 0.2 4 NUMBER OF CYCLES AT 60Hz FIG.4 - TYPICAL FORWARD CHARACTERISTICS 0 2 10 TJ = 100 °C 1.0 0.1 TJ = 25 °C 0.01 0 20 40 60 80 100 120 140 PERCENT OF RATED REVERSE VOLTAGE, (%) Rev. 02 : March 25, 2005