HONEYWELL HMC5843

3-Axis Digital Compass IC
HMC5843
The Honeywell HMC5843 is a surface mount multi-chip module designed
for low field magnetic sensing with a digital interface for applications such
as low cost compassing and magnetometry. The HMC5843 includes our
state of the art 1043 series magneto-resistive sensors plus Honeywell
developed ASIC containing amplification, strap drivers, offset cancellation,
2
12-bit ADC and an I C serial bus interface. The HMC5843 is in a 4.0 by 4.0
by 1.3mm surface mount leadless chip carrier (LCC). Applications for the
HMC5843 include Consumer Electronics, Auto Navigation Systems,
Personal Navigation Devices, and Magnetometers.
The HMC5843 utilizes Honeywell’s Anisotropic Magnetoresistive (AMR) technology that provides advantages over other
magnetic sensor technologies. The sensors feature precision in-axis sensitivity and linearity, solid-state construction with
very low cross-axis sensitivity designed to measure both direction and magnitude of Earth’s magnetic fields, from tens of
micro-gauss to 6 gauss. Honeywell’s Magnetic Sensors are among the most sensitive and reliable low-field sensors in the
industry.
Honeywell continues to maintain product excellence and performance by introducing innovative solid-state magnetic
sensor solutions. These are highly reliable, top performance products that are delivered when promised. Honeywell’s
magnetic sensor solutions provide real solutions you can count on.
FEATURES
BENEFITS
4
3-Axis Magnetoresistive Sensors and
ASIC in a Single Package
Size for Highly Integrated Products. Just Add a Micro4 Small
Controller Interface, Plus Two External SMT Capacitors
4
Low Cost
4 Designed for High Volume, Cost Sensitive OEM Designs
4
4.0 x 4.0 x 1.3mm Low Height Profile
LCC Surface Mount Package
4 Easy to Assemble & Compatible with High Speed SMT Assembly
4
Low Voltage Operations (2.5 to 3.3V)
4 Compatible for Battery Powered Applications
4
Built-In Strap Drive Circuits
and Offset Strap Drivers for Degaussing, Self Test, and
4 Set/Reset
Offset Compensation
4
I C Digital Interface
4 Popular Two-Wire Serial Data Interface for Consumer Electronics
4
Lead Free Package Construction
4 Complies with Current Environmental Standards
4
Wide Magnetic Field Range (+/-6 Oe)
4 Sensors Can Be Used in Strong Magnetic Field Environments
4
Available in Tape & Reel Packaging
4 High Volume OEM Assembly
2
HMC5843
SPECIFICATIONS (* Tested at 25°C except stated otherwise.)
Characteristics
Conditions*
Min
AVDD Referenced to AGND
2.5
DVDD Referenced to DGND
1.6
Sleep Mode (dual supplies)
Typ
Max
Units
3.3
Volts
1.8
2.0
Volts
-
2.5
-
uA
Idle Mode (dual supplies)
-
240
-
uA
Measurement Mode
-
0.8
-
mA
Sleep Mode (single supply)
-
110
-
uA
Idle Mode (single supply)
-
340
-
uA
Measurement Mode
-
0.9
-
mA
+4
gauss
Power Supply
Supply Voltage
Current Draw
AVDD = 2.5 volts, DVDD = 1.8 volts
AVDD = 2.5 volts
Performance
Field Range
Cross-Axis Sensitivity
Disturbing Field
Max. Exposed Field
Measurement Period
2
I C Address
Full scale (FS) – total applied field
Cross field = 0.5 gauss,
Happlied = ±3 gauss
gauss
No perming effect on zero reading
10000
gauss
10
msec
Output Rate = 50Hz (10Hz typ.)
-
7-bit address
0x1E
hex
8-bit read address
0x3D
hex
8-bit write address
0x3C
hex
Controlled by I C Master
Internal passive resistors
2
Hysteresis of Schmitt trigger inputs on SCL
I C Hysteresis
Self Test
Mag Dynamic Range
Linearity
Gain Tolerance
%FS/gauss
20
2
I C bus pull-up
±0.2%
Sensitivity starts to degrade.
Use S/R pulse to restore sensitivity.
2
I C Rate
-4
2
-10
+10
%
50
kilo-ohms
and SDA - Fall (DVDD=1.8V)
0.603
Volts
Rise (DVDD=1.8V)
1.108
Volts
Positive and Negative Bias Mode
±0.55
gauss
3-bit gain control
±0.7
±1.0
Full scale input range
±4.0
gauss
0.1
±% FS
All gain/dynamic range settings
±5
%
Bandwidth
-3dB point
10
kHz
Resolution
AVDD=3.0V, GN
7
milli-gauss
Signal-to Noise Ratio
70
Turn-on Time
dB
200
us
General
ESD Voltage
Operating Temperature
Storage Temperature
Weight
2
700
V
Ambient
-30
85
°C
Ambient, unbiased
-40
125
°C
Nominal
50
milli-grams
www.honeywell.com
HMC5843
PIN CONFIGURATIONS
(Arrow indicates direction of applied field that generates a positive output voltage after a SET pulse.)
Pin
Name
Description
1
SCL
2
SDAP
Serial Data Pull-up Resistor – 50k-ohm to VDD
3
SCLP
Serial Clock Pull-up Resistor – 50k-ohm to VDD
4
NC
No Connection
5
NC
No Connection
6
OFFP
Offset Strap Positive
7
8
OFFN
NC
Offset Strap Negative
No Connection
9
SETP
Set/Reset Strap Positive – S/R Capacitor (C2) Connection
10
SETN
Set/Reset Strap Negative – Test Point
11
SVDD
Sensor Supply – Test Point
12
DGND
Digital Supply Ground/Return
13
C1
14
15
SETC
DVDD
S/R Capacitor (C2) Connection – Driver Side
Digital Positive Supply
16
VREN
Voltage Regulator Enable, (GND = Dual Supply, AVDD = Single Supply)
17
AGND
Analog Supply Ground/Return
18
AVDD
Analog Positive Supply
19
DRDY
Data Ready – Test Point
20
SDA
Serial Clock – I2C Master/Slave Clock
Reservoir Capacitor (C1) Connection
Serial Data – I2C Master/Slave Data
Table 1: Pin Configurations
SCL
SDAP
SCLP
TP1
TP0
1
2
3
4
5
SDA 20
DRDY 19
6
OFFP
7
OFFN
8
NC
9
SETP
10
SETN
Z
AVDD 18
Y
AGND 17
VREN 16
X
15
14
13
12
11
DVDD
SETC
C1
DGND
SVDD
HMC5843 – bottom view
www.honeywell.com
3
HMC5843
PACKAGE OUTLINES
PACKAGE DRAWING HMC5843 (20-PIN LPCC, dimensions in millimeters)
Pin 1
D3
D2
A
E2
Sym
Min
Nom
Max
A
1.20
-
1.46
E
L
e
D
4.0 BSC
D2
2.25
D3
0.25 x 20 pins
E
4.0 BSC
E2
2.25
e
0.50 Basic
L
0.40 x 20 pins
D
HMC5843 – bottom view
MOUNTING CONSIDERATIONS
The following is the recommend printed circuit board (PCB) footprint for the HMC5843.
PCB Pad Definition and Traces
The HMC5843 is a fine pitch LCC package with a 0.50mm pin pitch (spacing), with the pin pads defined as 0.40mm by
0.25mm in size. PCB pads are recommended to be oversized by 0.025mm from each pad for a short dimension oversize
of 0.05mm. The interior PCB pad is recommended to be 0.05mm oversized per pin with an exterior oversize of 0.20mm
for proper package centering and to permit test probing. Size the traces between the HMC5843 and the external
capacitors (C1 and C2) to handle the 1 ampere peak current pulses with low voltage drop on the traces.
Stencil Design and Solder Paste
A 4 mil stencil and 100% paste coverage is recommended for the electrical contact pads.
Pick and Place
Placement is machine dependant and no restrictions are recommended, and have been tested with mechanical centering.
Placement force should be equivalent 1206 SMT resistors and enough force should be used to squeeze the paste out
from the package/contact pad overlap and to keep the package pin contacts vertical.
Reflow and Rework
No special profile is required for the HMC5843 and compatible with lead eutectic and lead-free solder paste reflow
profiles. Honeywell recommends the adherence to solder paste manufacturer’s guidelines. The HMC5843 may be
reworked with soldering irons, but extreme care must be taken not to overheat the copper pads from the part’s fiberglass
substrate. Irons with a tip temperature no greater than 315°C should be used. Excessive rework risks the copper pads
pulling away into the molten solder.
4
www.honeywell.com
HMC5843
INTERNAL SCHEMATIC DIAGRAM
HMC5843
DUAL SUPPLY REFERENCE DESIGN
www.honeywell.com
5
HMC5843
SINGLE SUPPLY REFERENCE DESIGN
BASIC DEVICE OPERATION
Anisotropic Magneto-Resistive Sensors
The Honeywell HMC5843 magnetoresistive sensor circuit is a trio of sensors and application specific support circuits to
measure magnetic fields. With power supply applied, the sensor converts any incident magnetic field in the sensitive axis
directions to a differential voltage output. The magnetoresistive sensors are made of a nickel-iron (Permalloy) thin-film and
patterned as a resistive strip element. In the presence of a magnetic field, a change in the bridge resistive elements
causes a corresponding change in voltage across the bridge outputs.
These resistive elements are aligned together to have a common sensitive axis (indicated by arrows on the pinouts) that
will provide positive voltage change with magnetic fields increasing in the sensitive direction. Because the output only is in
proportion to the one-dimensional axis (the principle of anisotropy) and its magnitude, additional sensor bridges placed at
orthogonal directions permit accurate measurement of arbitrary field direction.
Self Test
An offset strap is designed for self test function. The offset strap measures nominally 13 ohms, and requires 10mA for
each gauss of induced field. The straps will easily handle currents to buck or boost fields through the ±4 gauss linear
measurement range, but designers should note the extreme thermal heating on the sensor die when doing so.
6
www.honeywell.com
HMC5843
Power Management
This device is capable of operating with a single supply (AVDD) or dual supplies (AVDD and DVDD). Pin VREN makes
this selection by enabling the internal digital supply voltage regulator. When VREN is tied to AVDD, the device is in single
supply operation; this device is powered from AVDD; and the internal voltage regulator is enabled. When VREN is tied
to AGND this devices operates with both AVDD and DVDD as supplies. The table below shows the modes available at
the various power supply conditions.
DVDD
AVDD
Pin
VREN
Modes
Supported
Description
High
High
AGND
All, except
Off
High
Low
AGND
Idle
Internally
regulated
High
AVDD
All, except
Off
Low
Low
--
Off
Internal voltage regulator: Disabled.
Digital I/O pins: Range from DGND to DVDD.
Device fully functional. Digital logic blocks are
powered from DVDD supply, including all onboard clocks.
Internal voltage regulator: Disabled.
Digital I/O pins: Range from DGND to DVDD.
Device Measurement functionality not supported.
2
Device I C bus and register access supported.
Internal voltage regulator: Enabled
Digital I/O pins: Range from AGND to AVDD
Device fully functional. Digital logic blocks are
powered through on-board regulator.
Device in off mode.
Table 2: Operational Modes and Supply States
Note the continuous current draw versus data update rate in micro-amperes shown in the graph below. Under 10Hz, the
current stays below 1mA.
www.honeywell.com
7
HMC5843
Voltage Regulator
This ASIC has an internal voltage regulator which, depending on the application needs, may be used instead of supplying
voltage to pin DVDD. If DVDD pin is used, the internal voltage regulator is not engaged. When both supplies are used,
DVDD is typically high before AVDD, but no latch-up conditions will exist if DVDD is brought high after AVDD.
Power on Reset
Power on reset (POR) circuit shall return the device to the power-on default state. All registers shall be returned to their
default values. Circuitry shall return to it default state, such as, but not limited to: MUX channel, ADC state machine, and
bias current.
2
I C Interface
2
Control of this device is carried out via the I C bus. This device will be connected to this bus as a slave device under the
control of a master device, such as the processor.
2
2
This device shall be compliant with I C-Bus Specification, document number: 9398 393 40011. As an I C compatible
2
device, this device has a 7-bit serial address and supports I C protocols. This device shall support standard and fast
modes, 100kHz and 400kHz respectively, but cannot support the high speed mode (Hs). External pull-up resistors are
required to support these standard and fast speed modes. Depending on the application, the internal pull-ups may be
2
used to support slower data speeds than specified by I C standards. This device does not contain 50nsec spike
2
suppression as required by fast mode operation in the I C-Bus Specification, “Table 4 Characteristics of the SDA and
2
SCL I/O stages for F/S-mode I C-bus devices”.
Activities required by the master (register read and write) have priority over internal activities, such as the measurement.
2
The purpose of this priority is to not keep the master waiting and the I C bus engaged for longer than necessary.
2
I C Pull-up Resistors
2
Pull-up resistors are placed on the two I C bus lines. Typically these resistors are off-chip, but, to conserve board space
in specific low clock speed applications, they are internal to this device.
Internal Clock
The device has an internal clock for internal digital logic functions and timing management.
H-Bridge for Set/Reset Strap Drive
The ASIC contains large switching FETs capable of delivering a large but brief pulse to the Set / Reset strap of the
sensor. This strap is largely a resistive load.
8
www.honeywell.com
HMC5843
Charge Current Limit
The current that reservoir capacitor (C1) can draw when charging is limited. When using dual supplies this device shall
limit the current drawn from DVDD source to charge this capacitor. When only a single supply is used, Pin DVDD is
externally tied to pin C1. In this configuration, current is still limited. For example, the internal voltage regulator will limit
this current draw.
Bias Current Generator
The bias current generator is used to apply a bias current to the offset strap of the magneto-resistive sensor, which
creates an artificial magnetic field bias on the sensor. This function is enabled and the polarity is set by bits MS[n] in the
configuration register. The bias current generator generates dc current supplied from the AVDD supply.
MODES OF OPERATION
This device has several modes whose primary purpose is power management. This section describes these modes.
Continuous-Measurement Mode
During continuous-measurement mode, the device continuously makes measurements and places measured data in data
output registers. Settings in the configuration register affect the data output rate (bits DO[n]), the measurement
configuration (bits MS[n]), and the gain (bits GN[n]) when in continuous-measurement mode. To conserve current
between measurements, the device is placed in a state similar to idle mode, but the mode is not changed to idle mode.
That is, MD[n] bits are unchanged. Data can be re-read from the data output registers if necessary; however, if the
master does not ensure that the data register is accessed before the completion of the next measurement, the new
2
measurement may be lost. All registers maintain values while in continuous-measurement mode. The I C bus is enabled
for use by other devices on the network in while continuous-measurement mode.
Single-Measurement Mode
This is the default single supply power-up mode. In dual supply configuration this is the default mode when AVDD goes
high. During single-measurement mode, the device makes a single measurement and places the measured data in data
output registers. Settings in the configuration register affect the measurement configuration (bits MS[n]), and the gain
(bits GN[n]) when in single-measurement mode. After the measurement is complete and output data registers are
updated, the device is placed sleep mode, and the mode register is changed to sleep mode by setting MD[n] bits. All
2
registers maintain values while in single-measurement mode. The I C bus is enabled for use by other devices on the
network while in single-measurement mode.
Idle Mode
2
During this mode the device is accessible through the I C bus, but major sources of power consumption are disabled,
such as, but not limited to, the ADC, the amplifier, the SVDD pin, and the sensor bias current. All registers maintain
2
values while in idle mode. The I C bus is enabled for use by other devices on the network while in idle mode.
Sleep Mode
This is the default dual supply power-up mode when only DVDD goes high and AVDD remains low. During sleep mode
2
the device functionality is limited to listening to the I C bus. The internal clock is not running and register values are not
maintained while in sleep mode. The only functionality that exists during this mode is the device is able to recognize and
2
execute any instructions specific to this device but does not change from sleep mode due to other traffic on the I C bus.
2
The I C bus is enabled for use by other devices on the network while in sleep mode. This mode has two practical
differences from idle mode. First this state will create less noise on system since the clock is disabled, and secondly this
state is a lower current consuming state since the clock is disabled.
Off Mode
2
During off mode device is off. No device functionality exists. Both AVDD and DVDD are low. The I C bus is enabled for
2
use by other devices on the network in off mode. In this mode the I C pins shall be in a high impedance state.
www.honeywell.com
9
HMC5843
REGISTERS
This device is controlled and configured via a number of on-chip registers, which are described in this section. In the
following descriptions, set implies a logic 1, and reset or clear implies a logic 0, unless stated otherwise.
Register List
The table below lists the registers and their access. All address locations are 8 bits.
Address Location
Name
Access
00
01
02
03
04
05
06
07
08
09
10
11
12
Configuration Register A
Configuration Register B
Mode Register
Data Output X MSB Register
Data Output X LSB Register
Data Output Y MSB Register
Data Output Y LSB Register
Data Output Z MSB Register
Data Output Z LSB Register
Status Register
Identification Register A
Identification Register B
Identification Register C
Read/Write
Read/Write
Read/Write
Read
Read
Read
Read
Read
Read
Read
Read
Read
Read
Table 5: Register List
Register Access
This section describes the process of reading from and writing to this device. The devices uses an address pointer to
indicate which register location is to be read from or written to. These pointer locations are sent from the master to this
slave device and succeed the 7-bit address plus 1 bit read/write identifier.
To minimize the communication between the master and this device, the address pointer updated automatically without
master intervention. This automatic address pointer update has two additional features. First when address 12 or higher
is accessed the pointer updates to address 00 and secondly when address 09 is reached, the pointer rolls back to
address 03. Logically, the address pointer operation functions as shown below.
If (address pointer = 09) then address pointer = 03
Else if (address pointer >= 12) then address pointer = 0
Else (address pointer) = (address pointer) + 1
2
The address pointer value itself cannot be read via the I C bus.
Any attempt to read an invalid address location returns 0’s, and any write to an invalid address location or an undefined bit
within a valid address location is ignored by this device.
10
www.honeywell.com
HMC5843
Configuration Register A
The configuration register is used to configure the device for setting the data output rate and measurement configuration.
CRA0 through CRA7 indicate bit locations, with CRA denoting the bits that are in the configuration register. CRA7 denotes
the first bit of the data stream. The number in parenthesis indicates the default value of that bit.
CRA7
CRA6
CRA5
CRA4
CRA3
CRA2
CRA1
CRA0
(0)
(0)
(0)
DO2 (1)
DO1 (0)
DO0 (0)
MS1 (0)
MS0 (0)
Table 6: Configuration Register A
Location
Name
Description
CRA7 to CRA5
0
These bits must be cleared for correct operation.
CRA4 to CRA2
DO2 to DO0
Data Output Rate Bits. These bits set the rate at which
data is written to all three data output registers.
MS1 to MS0
Measurement Configuration Bits. These bits define the
measurement flow of the device, specifically whether or
not to incorporate an applied bias to the sensor into the
measurement.
CRA1 to CRA0
Table 7: Configuration Register A Bit Designations
The Table below shows minimum output data rates given PVT conditions. All three channels shall be measured within a
given data rate.
DO2
DO1
DO0
Minimum Data Output Rate (Hz)
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0.5
1
2
5
10 (default)
20
50
Not used
Table 8: Data Output Rates
MS1
MS0
Mode
0
0
Normal measurement configuration (default). In normal measurement
configuration the device follows normal measurement flow. Pins BP and BN
are left floating and high impedance.
0
1
Positive bias configuration. In positive bias configuration, a positive current
is forced across the resistive load on pins BP and BN.
1
0
Negative bias configuration. In negative bias configuration, a negative
current is forced across the resistive load on pins BP and BN.
1
1
This configuration is not used.
Table 9: Measurement Modes
www.honeywell.com
11
HMC5843
Configuration Register B
The configuration register B for setting the device gain. CRB0 through CRB7 indicate bit locations, with CRB denoting the
bits that are in the configuration register. CRB7 denotes the first bit of the data stream. The number in parenthesis
indicates the default value of that bit.
CRB7
CRB6
CRB5
CRB4
CRB3
CRB2
CRB1
CRB0
GN2 (0)
GN1 (0)
GN0 (1)
(0)
(0)
(0)
(0)
(0)
Table 10: Configuration B Register
Location
Name
Description
CRB7 to CRB5
GN2 to GN0
Gain Configuration Bits. These bits configure the gain for
the device. The gain configuration is common for all
channels.
CRB4 to CRB0
0
This bit must be cleared for correct operation.
Table 11: Configuration Register B Bit Designations
The table below shows nominal gain settings.
Gain
(counts/
milli-gauss)
GN2
GN1
GN0
Sensor Input Field
Range:
0
0
0
±0.7Ga
1620
0xF800–0x07FF
(-2048–2047 )
0
0
1
±1.0Ga (default)
1300
0xF800–0x07FF
(-2048–2047 )
0
1
0
±1.5Ga
970
0xF800–0x07FF
(-2048–2047 )
0
1
1
±2.0Ga
780
0xF800–0x07FF
(-2048–2047 )
1
0
0
±3.2Ga
530
0xF800–0x07FF
(-2048–2047 )
1
0
1
±3.8Ga
460
0xF800–0x07FF
(-2048–2047 )
1
1
0
±4.5Ga
390
0xF800–0x07FF
(-2048–2047 )
1
1
1
±6.5Ga
(Not Recommended)
280
0xF800–0x07FF
(-2048–2047 )
Output Range
Table 12: Gain Settings
12
www.honeywell.com
HMC5843
The resolution of the HMC5843 is based on the gain selection (zero to 7) and the influence of the analog power supply rail
(AVDD). The following graph shows the interaction.
HMC5843 Resolution
Resolution (mGa)
12
Gain
0
1
2
3
4
5
6
7
10
8
6
4
2
2.4
2.6
2.8
3.0
AVDD (V)
3.2
Mode Register
The mode register is an 8-bit register from which data can be read or to which data can be written. This register is used to
select the operating mode of the device. MR0 through MR7 indicate bit locations, with MR denoting the bits that are in the
mode register. MR7 denotes the first bit of the data stream. The number in parenthesis indicates the default value of that
bit.
MR7
MR6
MR5
MR4
MR3
MR2
MR1
MR0
(0)
(0)
(0)
(0)
(0)
(0)
MD1 (1)
MD0 (0)
Table 14: Mode Register
Location
Name
Description
MR7 to
MR2
0
These bits must be cleared for correct operation.
MR1 to
MR0
MD1 to
MD0
Mode Select Bits. These bits select the operation mode of
this device.
Table 15: Mode Register Bit Designations
www.honeywell.com
13
HMC5843
MD1
MD0
Mode
Continuous-Conversion Mode. In continuous-conversion mode, the
device continuously performs conversions an places the result in the
data register. RDY goes high when new data is placed in all three
registers. After a power-on or a write to the mode or configuration
register, the first measurement set is available from all three data
output registers after a period of 2/fDO and subsequent
measurements are available at a frequency of fDO, where fDO is the
frequency of data output.
Single-Conversion Mode. When single-conversion mode is selected,
device performs a single measurement, sets RDY high and returned
to sleep mode. Mode register returns to sleep mode bit values. The
measurement remains in the data output register and RDY remains
high until the data output register is read or another conversion is
performed.
0
0
0
1
1
0
Idle Mode. Device is placed in idle mode.
1
1
Sleep Mode. Device is placed in sleep mode.
Table 16: Operating Modes
Data Output X Registers A and B
The data output X registers are two 8-bit registers, data output register A and data output register B. These registers
store the measurement result from channel X. Data output X register A contains the MSB from the measurement result,
and data output X register B contains the LSB from the measurement result. The value stored in these two registers is a
16-bit value in 2’s complement form, whose range is 0xF800 to 0x07FF. DXRA0 through DXRA7 and DXRB0 through
DXRB7 indicate bit locations, with DXRA and DXRB denoting the bits that are in the data output X registers. DXRA7 and
DXRB7 denote the first bit of the data stream. The number in parenthesis indicates the default value of that bit.
In the event the ADC reading overflows or underflows for the given channel, or if there is a math overflow during the bias
measurement, this data register will contain the value -4096 in 2’s complement form. This register value will clear when
after the next valid measurement is made.
DXRA7
DXRA6
DXRA5
DXRA4
DXRA3
DXRA2
DXRA1
DXRA0
(0)
(0)
(0)
(0)
(0)
(0)
(0)
(0)
DXRB7
DXRB6
DXRB5
DXRB4
DXRB3
DXRB2
DXRB1
DXRB0
(0)
(0)
(0)
(0)
(0)
(0)
(0)
(0)
Table 17: Data Output X Registers A and B
Data Output Y Registers A and B
The data output Y registers are two 8-bit registers, data output register A and data output register B. These registers
store the measurement result from channel Y. Data output Y register A contains the MSB from the measurement result,
and data output Y register B contains the LSB from the measurement result. The value stored in these two registers is a
16-bit value in 2’s complement form, whose range is 0xF800 to 0x07FF. DYRA0 through DYRA7 and DYRB0 through
DYRB7 indicate bit locations, with DYRA and DYRB denoting the bits that are in the data output Y registers. DYRA7 and
DYRB7 denote the first bit of the data stream. The number in parenthesis indicates the default value of that bit.
In the event the ADC reading overflows or underflows for the given channel, or if there is a math overflow during the bias
measurement, this data register will contain the value -4096 in 2’s complement form. This register value will clear when
after the next valid measurement is made.
14
www.honeywell.com
HMC5843
DYRA7
DYRA6
DYRA5
DYRA4
DYRA3
DYRA2
DYRA1
DYRA0
(0)
(0)
(0)
(0)
(0)
(0)
(0)
(0)
DYRB7
DYRB6
DYRB5
DYRB4
DYRB3
DYRB2
DYRB1
DYRB0
(0)
(0)
(0)
(0)
(0)
(0)
(0)
(0)
Table 18: Data Output Y Registers A and B
Data Output Z Registers A and B
The data output Z registers are two 8-bit registers, data output register A and data output register B. These registers
store the measurement result from channel Z. Data output Z register A contains the MSB from the measurement result,
and data output Z register B contains the LSB from the measurement result. The value stored in these two registers is a
16-bit value in 2’s complement form, whose range is 0xF800 to 0x07FF. DZRA0 through DZRA7 and DZRB0 through
DZRB7 indicate bit locations, with DZRA and DZRB denoting the bits that are in the data output Z registers. DZRA7 and
DZRB7 denote the first bit of the data stream. The number in parenthesis indicates the default value of that bit.
In the event the ADC reading overflows or underflows for the given channel, or if there is a math overflow during the bias
measurement, this data register will contain the value -4096 in 2’s complement form. This register value will clear when
after the next valid measurement is made.
DZRA7
DZRA6
DZRA5
DZRA4
DZRA3
DZRA2
DZRA1
DZRA0
(0)
(0)
(0)
(0)
(0)
(0)
(0)
(0)
DZRB7
DZRB6
DZRB5
DZRB4
DZRB3
DZRB2
DZRB1
DZRB0
(0)
(0)
(0)
(0)
(0)
(0)
(0)
(0)
Table 19: Data Output Z Registers A and B
Data Output Register Operation
When one or more of the output registers are read, new data cannot be placed in any of the output data registers until all
six data output registers are read. This requirement also impacts DRDY and RDY, which cannot be cleared until new
data is placed in all the output registers.
Status Register
The status register is an 8-bit read-only register. This register is used to indicate device status. SR0 through SR7
indicate bit locations, with S R denoting the bits that are in the status register. SR7 denotes the first bit of the data stream.
SR7
SR6
SR5
SR4
SR3
SR2
SR1
SR0
(0)
(0)
(0)
(0)
(0)
REN (0)
LOCK (0)
RDY(0)
Table 20: Status Register
www.honeywell.com
15
HMC5843
Location
Name
Description
SR7 to
SR3
0
These bits must be cleared for correct operation.
SR2
REN
Regulator Enabled Bit. This bit is set when the internal
voltage regulator is enabled. This bit is cleared when the
internal regulator is disabled.
SR1
LOCK
SR0
RDY
Data output register lock. This bit is set when this some but
not all for of the six data output registers have been read.
When this bit is set, the six data output registers are locked
and any new data will not be placed in these register until
on of four conditions are met: one, all six have been read
or the mode changed, two, a POR is issued, three, the
mode is changed, or four, the measurement is changed.
Ready Bit. Set when data is written to all six data registers.
Cleared when device initiates a write to the data output
registers, when in off mode, and after one or more of the
data output registers are written to. When RDY bit is clear
it shall remain cleared for a minimum of 5 µs. DRDY pin
can be used as an alternative to the status register for
monitoring the device for conversion data.
Table 21: Status Register Bit Designations
Identification Register A
The identification register A is used to identify the device. IRA0 through IRA7 indicate bit locations, with IRA denoting the
bits that are in the identification register A. IRA7 denotes the first bit of the data stream. The number in parenthesis
indicates the default value of that bit.
The identification value for this device is stored in this register. This is a read-only register.
Register values. ASCII value H
IRA7
IRA6
IRA5
IRA4
IRA3
IRA2
IRA1
IRA0
0
1
0
0
1
0
0
0
Table 22: Identification Register A Default Values
16
www.honeywell.com
HMC5843
Identification Register B
The identification register B is used to identify the device. IRB0 through IRB7 indicate bit locations, with IRB denoting the
bits that are in the identification register A. IRB7 denotes the first bit of the data stream.
Register values. ASCII value 4
IRB7
IRB6
IRB5
IRB4
IRB3
IRB2
IRB1
IRB0
0
0
1
1
0
1
0
0
Table 23: Identification Register B Default Values
Identification Register C
The identification register C is used to identify the device. IRC0 through IRC7 indicate bit locations, with IRC denoting the
bits that are in the identification register A. IRC7 denotes the first bit of the data stream.
Register values. ASCII value 3
IRC7
IRC6
IRC5
IRC4
IRC3
IRC2
IRC1
IRC0
0
0
1
1
0
0
1
1
Table 24: Identification Register C Default Values
www.honeywell.com
17
HMC5843
I2C COMMUNICATION PROTOCOL
The HMC5843 communicates via a two-wire I2C bus system as a slave device. The HMC5843 uses a simple protocol
with the interface protocol defined by the I2C bus specification, and by this document. The data rate is at the standardmode 100kbps or 400kbps rates as defined in the I2C Bus Specifications. The bus bit format is an 8-bit Data/Address
send and a 1-bit acknowledge bit. The format of the data bytes (payload) shall be case sensitive ASCII characters or
binary data to the HMC5843 slave, and binary data returned. Negative binary values will be in two’s complement form.
The default (factory) HMC5843 7-bit slave address is 0x3C for write operations, or 0x3D for read operations.
The HMC5843 Serial Clock (SCL) and Serial Data (SDA) lines have optional internal pull-up resistors, but require resistive
pull-ups (Rp) between the master device (usually a host microprocessor) and the HMC5843. Pull-up resistance values of
about 10k ohms are recommended with a nominal 1.8-volt digital supply voltage (DVDD). Other values may be used as
defined in the I2C Bus Specifications or with the internal 50k ohm pull-up resistors (SDAP, SCLP) that can be tied to
DVDD.
The SCL and SDA lines in this bus specification can be connected to a host of devices. The bus can be a single master to
multiple slaves, or it can be a multiple master configuration. All data transfers are initiated by the master device which is
responsible for generating the clock signal, and the data transfers are 8 bit long. All devices are addressed by I2C’s
unique 7 bit address. After each 8-bit transfer, the master device generates a 9 th clock pulse, and releases the SDA line.
The receiving device (addressed slave) will pull the SDA line low to acknowledge (ACK) the successful transfer or leave
the SDA high to negative acknowledge (NACK).
Per the I2C spec, all transitions in the SDA line must occur when SCL is low. This requirement leads to two unique
conditions on the bus associated with the SDA transitions when SCL is high. Master device pulling the SDA line low while
the SCL line is high indicates the Start (S) condition, and the Stop (P) condition is when the SDA line is pulled high while
the SCL line is high. The I2C protocol also allows for the Restart condition in which the master device issues a second
start condition without issuing a stop.
All bus transactions begin with the master device issuing the start sequence followed by the slave address byte. The
address byte contains the slave address; the upper 7 bits (bits7-1), and the Least Significant bit (LSb). The LSb of the
address byte designates if the operation is a read (LSb=1) or a write (LSb=0). At the 9 th clock pulse, the receiving slave
device will issue the ACK (or NACK). Following these bus events, the master will send data bytes for a write operation, or
the slave will clock out data with a read operation. All bus transactions are terminated with the master issuing a stop
sequence.
I2C bus control can be implemented with either hardware logic or in software. Typical hardware designs will release the
SDA and SCL lines as appropriate to allow the slave device to manipulate these lines. In a software implementation, care
must be taken to perform these tasks in code.
OPERATIONAL EXAMPLES
The HMC5843 has a fairly quick stabilization time from no voltage to stable and ready for data retrieval. The nominal 5
milli-seconds with the factory default single measurement mode means that the six Bytes of magnetic data registers
(DXRA, DXRB, DYRA, DYRB, DZRA, and DZRB) are filled with a valid first measurement.
To change the measurement mode to continuous measurement mode, after the 5 milli-second power-up time send the
three bytes:
0x3C 0x02 0x00
This writes the 00 into the second register or mode register to switch from single to continuous measurement mode
setting. With the data rate at the factory default of 10Hz updates (100 milli-seconds interval), a 100 milli-second delay
should be made by the I2C master before querying the HMC5843 data registers for new measurements. To clock out the
new data, send:
0x3D, and clock out DXRA, DXRB, DYRA, DYRB, DZRA, DZRB located in registers 3 through 8. The HMC5843 will
automatically re-point back to register 3 for the next 0x3D query, expected 100 milli-seconds or later.
18
www.honeywell.com
HMC5843
SELF TEST OPERATION
To check the HMC5843 for proper operation, a self test feature in incorporated in which the sensor offset straps are
excited to create a nominal field strength (bias field) to be measured. To implement this self test, the least significant bits
(MS1 and MS0) of configuration register A are changed from 00 to 01 (0x12 or 0b000xxx01). By placing the mode register
into single-conversion mode (0x01), two data acquisition cycles will be made on each magnetic vector. The first
acquisition will be a set pulse followed shortly by measurement data of the external field. The second acquisition will have
the offset strap excited in the positive bias mode (~5.5mA in offset straps) to create about a 0.55 gauss self test field plus
the external field. The first acquisition values will be subtracted from the second acquisition, and the net measurement will
be placed into the data output registers.
If the configuration register B is left at the factory default value of 0x20, values around +715 ADC counts (0.55Ga * 1300
counts/Ga) will be placed in the data output registers. To leave the self test mode, change MS1 and MS0 bit of the
configuration register A back to 0x00. Also change the mode register if single-conversion mode is not the intended next
mode of operation.
SCALE FACTOR CALIBRATION
Using the method described above in section SELF TEST OPERATION, user can scale sensors’ sensitivity to match each
other. Since placing device in positive bias mode (or alternatively negative bias mode) applies the same artificial field on
all three axis, the resulting ADC measurement in data output registers can be used to scale the sensors.
EXTERNAL CAPACITORS
The two external capacitors should be ceramic type construction with low ESR characteristics. Reservoir capacitor C1 is
nominally 4.7 micro-farads in capacitance, with the set/reset capacitor C2 nominally 0.22 micro-farads in capacitance.
Low ESR characteristics may not be in many smallest size SMT ceramic capacitors (0402), so be prepared to up-size the
capacitors to gain Low ESR characteristics.
ORDERING INFORMATION
Ordering Number
Product
HMC5843
3-Axis Digital Compass IC
HMC5843-TR
Tape and Reel 2.5k pieces/reel
HMC5843-demo
Demonstration Kit
HMC5843-eval
Evaluation Board
FIND OUT MORE
For more information on Honeywell’s Magnetic Sensors visit us online at www.honeywell.com/magneticsensors or contact
us at 800-323-8295 (763-954-2474 internationally).
The application circuits herein constitute typical usage and interface of Honeywell product. Honeywell does not warranty or assume liability of customerdesigned circuits derived from this description or depiction.
Honeywell reserves the right to make changes to improve reliability, function or design. Honeywell does not assume any liability arising out of the
application or use of any product or circuit described herein; neither does it convey any license under its patent rights nor the rights of others.
U.S. Patents 4,441,072, 4,533,872, 4,569,742, 4,681,812, 4,847,584 and 6,529,114 apply to the technology described
Honeywell
12001 Highway 55
Plymouth, MN 55441
Tel: 800-323-8295
www.honeywell.com
www.honeywell.com/magneticsensors
Form #900367
February 2009
©2009 Honeywell International Inc.
19