CAPACITOR ARRAYS Capacitor arrays combine separate multi-layer ceramic capacitors of the same value in a single passive component. The primary advantages of this device are a reduction in PCB space and placement time. The arrays are offered in three standard dielectrics and feature barrier terminations and tape & reel packaging. FEATURES APPLICATIONS • Multiple Caps in One Chip • Reduces Circuit Size • Easier Handling • Lower Placement Cost • Increased Throughput • Cellular / Pagers • Handheld Equipment • PCMCIA Cards • Camcorders • PC’s & Peripherals CAPACITANCE / VOLTAGE SELECTION RATED VOLTAGE CHIP SIZE A11 / 0405 A18 / 0612 NPO DIELECTRIC min. MAX. X7R DIELECTRIC min. MAX. Y5V DIELECTRIC min. MAX. 10 VDC 10 pF 680 pF 560 pF .047 µF 16 VDC 10 pF 680 pF 560 pF .033 µF 25 VDC 10 pF 680 pF 560 pF .022 µF 16 VDC .033 µF .047 µF .150 µF .220 µF 25 VDC .015 µF .022 µF .068 µF .100 µF .010 µF .047 µF 50 VDC 330 pF 470 pF 6800 pF .010 µF 100 VDC 10 pF 220 pF 220 pF 4700 pF Available capacitance values include the following significant R12 retma values and their multiples: 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 ( 1.0 = 1.0, 10, 100, 1000, etc.) Please contact the factory for size/voltage/value combinations not shown. HOW TO ORDER - CAPACITOR ARRAYS 160 VOLTAGE 100 = 10 V 160 = 16 V 250 = 25 V 500 = 50 V 101 = 100 V A11 CASE SIZE A11 = 0405 A18 = 0612 N 100 DIELECTRIC N = NPO W = X7R Y = Y5V CAPACITANCE 1st two digits are significant; third digit denotes number of zeros 10 = 1.0 pF 101 = 100 pF J TOLERANCE J = ± 5% K = ± 10% M = ± 20% Z = + 80 - 20% V TERMINATION V = Ni barrier w/ 100% Sn Plating MARKING 4 = Unmarked P/N written: 160A11N100JV4E 12 www.johanson dielectrics.com 4 E TAPE MODIFIER Code Type Reel E Embossed 7” U Embossed 13” Tape specifications conform to EIA RS481 CAPACITOR ARRAYS Mechanical Dimensions: Size A11 In (mm) L .040 ± .005 (1.02±.13) W .055 ± .005 (1.40±.13) T .030 max. (0.76 max.) Bw .015 ± .004 (0.38±0.10) Bl .010 ± .004 (0.25±0.10) P .026 ± .005 (0.66±0.13) C .013 ± .004 (0.33±0.10) W P L T Bl Center of Chip Bc Bw C Bc C/L of Chip Bs Bs T Mechanical Dimensions: Size A18 B In (mm) L .126±.008 (3.20±.02) W .063±.008 (1.60±.02) T .059 max. (1.50 max.) B .016±.004 (0.41±0.1) Bo .008 Typical (0.20 TYP) Bs .030 Typical (0.76 TYP) Bc .045±.004 (1.14±0.1) L W Center of Chip Bo Bc Bc Bs Bs T B L Solder Pad Dimensions: Size A18 Solder Pad Dimensions: Size A11 a b c d e Inches .020 .030 .060 .013 .026 (mm) (0.51) (0.76) (1.52) (0.33) (0.66) e a b c d e Inches .035 .065 .100 .018 .030 (mm) (0.89) (1.65) (2.54 ) (0.46) Bo (0.79) W e d d c a c b b a Dielectric specifications are listed on page 20. www.johanson dielectrics.com 13