27C128 128K (16K x 8) CMOS EPROM PACKAGE TYPES 28 27 26 25 24 23 22 21 20 19 18 17 16 15 VCC PGM A13 A8 A9 A11 OE A10 CE O7 O6 O5 O4 O3 30 31 1 32 2 5 29 6 28 7 8 9 10 27 26 25 24 A8 A9 A11 NC OE A10 CE O7 O6 20 19 21 18 22 13 17 23 12 16 11 15 A6 A5 A4 A3 A2 A1 A0 NC O0 3 4 A7 A12 V PP NU Vcc PGM A13 PLCC 14 The Microchip Technology Inc. 27C128 is a CMOS 128K bit (electrically) Programmable Read Only Memory. The device is organized as 16K words by 8 bits (16K bytes). Accessing individual bytes from an address transition or from power-up (chip enable pin going low) is accomplished in less than 120 ns. CMOS design and processing enables this part to be used in systems where reduced power consumption and high reliability are requirements.A complete family of packages is offered to provide the most flexibility in applications. For surface mount applications, PLCC, SOIC, or TSOP packaging is available. Tape and reel packaging is also available for PLCC or SOIC packages. UV erasable versions are also available. • 1 2 3 4 5 6 7 8 9 10 11 12 13 14 VPP A12 A7 A6 A5 A4 A3 A2 A1 A0 O0 O1 O2 VSS 27C128 DESCRIPTION DIP/SOIC 27C128 • High speed performance - 120 ns access time available • CMOS Technology for low power consumption - 20 mA Active current - 100 µA Standby current • Factory programming available • Auto-insertion-compatible plastic packages • Auto ID aids automated programming • Separate chip enable and output enable controls • High speed “express” programming algorithm • Organized 16K x 8: JEDEC standard pinouts - 28-pin Dual-in-line package - 32-pin PLCC Package - 28-pin SOIC package - Tape and reel • Available for the following temperature ranges: - Commercial: 0˚C to +70˚C - Industrial: -40˚C to +85˚C - Automotive: -40˚C to +125˚C O1 O2 VSS NU O3 O4 O5 FEATURES A complete family of packages is offered to provide the most flexibility in applications. For surface mount applications, PLCC or SOIC packaging is available. Tape and reel packaging is also available for PLCC or SOIC packages. 1996 Microchip Technology Inc. DS11003K-page 1 This document was created with FrameMaker 4 0 4 27C128 1.0 ELECTRICAL CHARACTERISTICS 1.1 Maximum Ratings* TABLE 1-1: PIN FUNCTION TABLE Name Function VCC and input voltages w.r.t. VSS ........ -0.6V to +7.25V A0-A13 VPP voltage w.r.t. VSS during programming .......................................... -0.6V to +14V CE Chip Enable OE Output Enable Voltage on A9 w.r.t. VSS ...................... -0.6V to +13.5V Address Inputs Output voltage w.r.t. VSS ............... -0.6V to VCC +1.0V PGM Program Enable Storage temperature .......................... -65˚C to +150˚C VPP Programming Voltage Ambient temp. with power applied ..... -65˚C to +125˚C O0 - O7 *Notice: Stresses above those listed under “Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. VCC +5V Power Supply VSS Ground NC No Connection; No Internal Connections NU Not Used; No External Connection Is Allowed TABLE 1-2: Data Output READ OPERATION DC CHARACTERISTICS VCC = +5V (±10%) Commercial: Industrial: Extended (Automotive): Parameter Tamb = 0˚C to +70˚C Tamb = -40˚C to +85˚C Tamb = -40°C to +125°C Part* Status Symbol Min. Max. Units Conditions Input Voltages all Logic "1" Logic "0" VIH VIL 2.0 -0.5 VCC+1 0.8 V V Input Leakage all — ILI -10 10 µA VIN = 0 to VCC Output Voltages all Logic "1" Logic "0" VOH VOL 2.4 0.45 V V IOH = -400 µA IOL = 2.1 mA Output Leakage all — ILO -10 10 µA VOUT = 0V to VCC Input Capacitance all — CIN — 6 pF VIN = 0V; Tamb = 25°C; f = 1 MHz Output Capacitance all — COUT — 12 pF VOUT = 0V; Tamb = 25°C; f = 1 MHz Power Supply Current, Active C I,E TTL input TTL input ICC1 ICC2 — — 20 25 mA mA VCC = 5.5V; VPP = VCC f = 1 MHz; OE = CE = VIL; IOUT = 0 mA; VIL = -0.1 to 0.8V; VIH = 2.0 to VCC; Note 1 Power Supply Current, Standby C I, E all TTL input TTL input CMOS input ICC(S) — — — 2 3 100 mA mA µA all all Read Mode Read Mode IPP VPP VCC-0.7 100 VCC µA V IPP Read Current VPP Read Voltage CE = VCC ± 0.2V VPP = 5.5V * Parts: C=Commercial Temperature Range; I, E=Industrial and Extended Temperature Ranges Note 1: Typical active current increases .75 mA per MHz up to operating frequency for all temperature ranges. DS11003K-page 2 1996 Microchip Technology Inc. 27C128 TABLE 1-3: READ OPERATION AC CHARACTERISTICS AC Testing Waveform: Output Load: Input Rise and Fall Times: Ambient Temperature: VIH = 2.4V and VIL = 0.45V; VOH = 2.0V VOL = 0.8V 1 TTL Load + 100 pF 10 ns Commercial: Tamb = 0˚C to +70˚C Industrial: Tamb = -40˚C to +85˚C Extended (Automotive): Tamb = -40°C to +125°C 27C128-12 27C128-15 27C128-17 27C128-20 27C128-25 Parameter Sym Units Conditions Min Max Min Max Min Max Min Max Min Max Address to Output Delay tACC — 120 — 150 — 170 — 200 — 250 ns CE=OE=VIL CE to Output Delay tCE — 120 — 150 — 170 — 200 — 250 ns OE=VIL OE to Output Delay tOE — 65 — 70 — 70 — 75 — 100 ns CE=VIL CE or OE to O/P High Impedance tOFF 0 50 0 50 0 50 0 55 0 60 ns Output Hold from Address CE or OE, whichever occurs first tOH 0 — 0 — 0 — 0 — 0 — ns FIGURE 1-1: READ WAVEFORMS VIH Address Valid Address VIL VIH CE VIL t CE(2) VIH OE VIL Outputs O0 - O7 VOH t OFF(1,3) t OH t OE(2) High Z Valid Output High Z VOL t ACC Notes: (1) tOFF is specified for OE or CE, whichever occurs first (2) OE may be delayed up to t CE - t OE after the falling edge of CE without impact on tCE (3) This parameter is sampled and is not 100% tested. 1996 Microchip Technology Inc. DS11003K-page 3 27C128 TABLE 1-4: PROGRAMMING DC CHARACTERISTICS Ambient Temperature: Tamb = 25°C ± 5°C VCC = 6.5V ± 0.25V, VPP = 13.0V ± 0.25V Parameter Status Symbol Min Max. Units Input Voltages Logic”1” Logic”0” VIH VIL 2.0 -0.1 VCC+1 0.8 V V Input Leakage — ILI -10 10 µA VIN = 0V to VCC Logic”1” Logic”0” VOH VOL 2.4 0.45 V V IOH = -400 µA IOL = 2.1 mA VCC Current, program & verify — ICC2 — 20 mA Note 1 VPP Current, program — IPP2 — 25 mA Note 1 A9 Product Identification — VH 11.5 12.5 V Output Voltages Conditions Note 1: VCC must be applied simultaneously or before VPP and removed simultaneously or after VPP TABLE 1-5: PROGRAMMING AC CHARACTERISTICS for Program, Program Verify and Program Inhibit Modes Parameter AC Testing Waveform: VIH=2.4V and VIL=0.45V; VOH=2.0V; VOL=0.8V Ambient Temperature: Tamb=25°C± 5°C VCC= 6.5V ± 0.25V, VPP = VH = 13.0V ± 0.25V Symbol Min Max Units Address Set-Up Time tAS 2 — µs Data Set-Up Time tDS 2 — µs Data Hold Time tDH 2 — µs Address Hold Time tAH 0 — µs Float Delay (2) tDF 0 130 ns VCC Set-Up Time tVCS 2 — µs Program Pulse Width (1) tPW 95 105 µs CE Set-Up Time tCES 2 — µs OE Set-Up Time tOES 2 — µs VPP Set-Up Time tVPS 2 — µs Data Valid from OE tOE — 100 ns Remarks 100 µs typical Note 1: For express algorithm, initial programming width tolerance is 100 µs ±5%. 2: This parameter is only sampled and not 100% tested. Output float is defined as the point where data is no longer driven (see timing diagram). DS11003K-page 4 1996 Microchip Technology Inc. 27C128 FIGURE 1-2: PROGRAMMING WAVEFORMS (1) Program Verify V IH Address Address Stable V IL t AS tAH V IH High Z Data Data In Stable V IL Data Out Valid tDF (2) t DH t DS 13.0 V (3) V PP t VPS 5.0 V 6.5 V (3) V CC t VCS 5.0 V V IH CE V IL t CES V IH PGM V IL tOES t PW tOE (2) V IH t OPW OE V IL Notes: (1) The input timing reference is 0.8V for VIL and 2.0V for VIH. (2) t DF and tOE are characteristics of the device but must be accommodated by the programmer. (3) Vcc = 6.5V ±0.25V, V PP = VH = 13.0V ±0.25V for Express algorithm. TABLE 1-6: MODES Operation Mode CE OE PGM VPP A9 O0 - O7 Read VIL VIL VIH VCC X DOUT Program VIL VIH VIL VH X DIN Program Verify VIL VIL VIH VH X DOUT Program Inhibit VIH X X VH X High Z Standby VIH X X VCC X High Z Output Disable VIL VIH VIH VCC X High Z Identity VIL VIL VIH VCC VH Identity Code X = Don’t Care 1.2 Read Mode (See Timing Diagrams and AC Characteristics) Read Mode is accessed when a) b) For Read operations, if the addresses are stable, the address access time (tACC) is equal to the delay from CE to output (tCE). Data is transferred to the output after a delay from the falling edge of OE (tOE). the CE pin is low to power up (enable) the chip the OE pin is low to gate the data to the output pins 1996 Microchip Technology Inc. DS11003K-page 5 27C128 1.3 Standby Mode The standby mode is defined when the CE pin is high (VIH) and a program mode is not defined. When these conditions are met, the supply current will drop from 20 mA to 100 µA. 1.4 Output Enable This feature eliminates bus contention in microprocessor-based systems in which multiple devices may drive the bus. The outputs go into a high impedance state when the following condition is true: • The OE and PGM pins are both high. 1.5 Erase Mode (U.V. Windowed Versions) Windowed products offer the capability to erase the memory array. The memory matrix is erased to the all 1’s state when exposed to ultraviolet light. To ensure complete erasure, a dose of 15 watt-second/cm2 is required. This means that the device window must be placed within one inch and directly underneath an ultraviolet lamp with a wavelength of 2537 Angstroms, intensity of 12,000µW/cm2 for approximately 20 minutes. 1.6 Programming Mode The Express Algorithm has been developed to improve the programming throughput times in a production environment. Up to ten 100-microsecond pulses are applied until the byte is verified. No overprogramming is required. A flowchart of the express algorithm is shown in Figure 1-3. Programming takes place when: a) b) c) d) e) VCC is brought to the proper voltage, VPP is brought to the proper VH level, the CE pin is low, the OE pin is high, and the PGM pin is low. Since the erased state is “1” in the array, programming of “0” is required. The address to be programmed is set via pins A0-A13 and the data to be programmed is presented to pins O0-O7. When data and address are stable, OE is high, CE is low and a low-going pulse on the PGM line programs that location. DS11003K-page 6 1.7 Verify After the array has been programmed it must be verified to ensure all the bits have been correctly programmed. This mode is entered when all the following conditions are met: a) b) c) d) e) VCC is at the proper level, VPP is at the proper VH level, the CE line is low, the PGM line is high, and the OE line is low. 1.8 Inhibit When programming multiple devices in parallel with different data, only CE or PGM need be under separate control to each device. By pulsing the CE or PGM line low on a particular device in conjunction with the PGM or CE line low, that device will be programmed; all other devices with CE or PGM held high will not be programmed with the data, although address and data will be available on their input pins (i.e., when a high level is present on CE or PGM); and the device is inhibited from programming. 1.9 Identity Mode In this mode specific data is output which identifies the manufacturer as Microchip Technology Inc. and device type. This mode is entered when Pin A9 is taken to VH (11.5V to 12.5V). The CE and OE lines must be at VIL. A0 is used to access any of the two non-erasable bytes whose data appears on O0 through O7. Pin Identity Manufacturer Device Type* Input Output H e x A0 0 O O O O O O O 7 6 5 4 3 2 1 0 VIL VIH 0 0 1 0 1 0 0 1 29 1 0 0 0 0 0 1 1 83 * Code subject to change 1996 Microchip Technology Inc. 27C128 FIGURE 1-3: PROGRAMMING EXPRESS ALGORITHM Conditions: Tamb = 25˚C ±5˚C VCC = 6.5 ±0.25V VPP = 13.0 ±0.25V Start ADDR = First Location VCC = 6.5V VPP = 13.0V X=0 Program one 100 µs pulse Increment X Verify Byte Pass Fail No X = 10 ? Last Address? Yes Device Failed Yes No Increment Address VCC = VPP = 4.5V, 5.5V Device Passed 1996 Microchip Technology Inc. Yes All bytes = original data? No Device Failed DS11003K-page 7 27C128 NOTES: DS11003K-page 8 1996 Microchip Technology Inc. 27C128 NOTES: 1996 Microchip Technology Inc. DS11003K-page 9 27C128 NOTES: DS11003K-page 10 1996 Microchip Technology Inc. 27C128 27C128 Product Identification System To order or to obtain information, e.g., on pricing or delivery, please use the listed part numbers, and refer to the factory or the listed sales offices. 27C128 –25 I /P Package: Temperature Range: L = P = SO = Blank = I = E = Access Time: 12 15 17 20 25 Device: 27C128 1996 Microchip Technology Inc. = = = = = Plastic Leaded Chip Carrier (PLCC) Plastic DIP (600 Mil) Plastic SOIC (300 Mil) 0˚C to +70˚C -40˚C to +85˚C -40˚C to +125˚C 120 ns 150 ns 170 ns 200 ns 250 ns 128K (16K x 8) CMOS EPROM DS11003K-page 11 WORLDWIDE SALES & SERVICE AMERICAS ASIA/PACIFIC EUROPE Corporate Office Microchip Technology Inc. 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 602 786-7200 Fax: 602 786-7277 Technical Support: 602 786-7627 Web: http://www.microchip.com Atlanta Microchip Technology Inc. 500 Sugar Mill Road, Suite 200B Atlanta, GA 30350 Tel: 770 640-0034 Fax: 770 640-0307 Boston Microchip Technology Inc. 5 Mount Royal Avenue Marlborough, MA 01752 Tel: 508 480-9990 Fax: 508 480-8575 Chicago Microchip Technology Inc. 333 Pierce Road, Suite 180 Itasca, IL 60143 Tel: 708 285-0071 Fax: 708 285-0075 Dallas Microchip Technology Inc. 14651 Dallas Parkway, Suite 816 Dallas, TX 75240-8809 Tel: 972 991-7177 Fax: 972 991-8588 Dayton Microchip Technology Inc. Suite 150 Two Prestige Place Miamisburg, OH 45342 Tel: 513 291-1654 Fax: 513 291-9175 Los Angeles Microchip Technology Inc. 18201 Von Karman, Suite 1090 Irvine, CA 92612 Tel: 714 263-1888 Fax: 714 263-1338 New York Microchip Technmgy Inc. 150 Motor Parkway, Suite 416 Hauppauge, NY 11788 Tel: 516 273-5305 Fax: 516 273-5335 San Jose Microchip Technology Inc. 2107 North First Street, Suite 590 San Jose, CA 95131 Tel: 408 436-7950 Fax: 408 436-7955 Toronto Microchip Technology Inc. 5925 Airport Road, Suite 200 Mississauga, Ontario L4V 1W1, Canada Tel: 905 405-6279 Fax: 905 405-6253 China Microchip Technology Unit 406 of Shanghai Golden Bridge Bldg. 2077 Yan’an Road West, Hongiao District Shanghai, Peoples Republic of China Tel: 86 21 6275 5700 Fax: 011 86 21 6275 5060 Hong Kong Microchip Technology RM 3801B, Tower Two Metroplaza 223 Hing Fong Road Kwai Fong, N.T. Hong Kong Tel: 852 2 401 1200 Fax: 852 2 401 3431 India Microchip Technology No. 6, Legacy, Convent Road Bangalore 560 025 India Tel: 91 80 526 3148 Fax: 91 80 559 9840 Korea Microchip Technology 168-1, Youngbo Bldg. 3 Floor Samsung-Dong, Kangnam-Ku, Seoul, Korea Tel: 82 2 554 7200 Fax: 82 2 558 5934 Singapore Microchip Technology 200 Middle Road #10-03 Prime Centre Singapore 188980 Tel: 65 334 8870 Fax: 65 334 8850 Taiwan, R.O.C Microchip Technology 10F-1C 207 Tung Hua North Road Taipei, Taiwan, ROC Tel: 886 2 717 7175 Fax: 886 2 545 0139 United Kingdom Arizona Microchip Technology Ltd. Unit 6, The Courtyard Meadow Bank, Furlong Road Bourne End, Buckinghamshire SL8 5AJ Tel: 44 1628 850303 Fax: 44 1628 850178 France Arizona Microchip Technology SARL Zone Industrielle de la Bonde 2 Rue du Buisson aux Fraises 91300 Massy - France Tel: 33 1 69 53 63 20 Fax: 33 1 69 30 90 79 Germany Arizona Microchip Technology GmbH Gustav-Heinemann-Ring 125 D-81739 Muenchen, Germany Tel: 49 89 627 144 0 Fax: 49 89 627 144 44 Italy Arizona Microchip Technology SRL Centro Direzionale Colleone Pas Taurus 1 Viale Colleoni 1 20041 Agrate Brianza Milan Italy Tel: 39 39 6899939 Fax: 39 39 689 9883 JAPAN Microchip Technology Intl. Inc. Benex S-1 6F 3-18-20, Shin Yokohama Kohoku-Ku, Yokohama Kanagawa 222 Japan Tel: 81 45 471 6166 Fax: 81 45 471 6122 9/3/96 All rights reserved. 1996, Microchip Technology Incorporated, USA. 9/96 Printed on recycled paper. Information contained in this publication regarding device applications and the like is intended through suggestion only and may be superseded by updates. No representation or warranty is given and no liability is assumed by Microchip Technology Incorporated with respect to the accuracy or use of such information, or infringement of patents or other intellectual property rights arising from such use or otherwise. Use of Microchip’s products as critical components in life support systems is not authorized except with express written approval by Microchip. No licenses are conveyed, implicitly or otherwise, under any intellectual property rights. The Microchip logo and name are registered trademarks of Microchip Technology Inc. All rights reserved. All other trademarks mentioned herein are the property of their respective companies. DS11003K-page 12 1996 Microchip Technology Inc.