KOA SPEER ELECTRONICS, INC. SS-227 R2 AHA 2/10/05 Three Termination Capacitor Type KGM CERTIFIED CERTIFIED 1. Features ■ ■ ■ ■ Surface mount type noise filter Plated terminals provide excellent solder resistance Small size and high rated DC current 0603-2A, 0805-2A, 1206-2A series is available in signal lines in addition to power line 2. Applications ■ ■ ■ Noise reduction in high frequency circuits D.C. power line Vcc line for gate array or microcomputer 3. Ordering & Specifying Information Type designation shall be as the following form. KGM 0805 H C T TE 220 2A Type Size Rated Voltage Temp. Charact. Termination Material Packaging Capacitance Rated Current 0603 0805 1206 1812 C: 16V E: 25V V: 35V H:50V C F T: Sn TE: 7" Embossed Taping 0603: 4,000 pcs/reel 0805: 4,000 pcs/reel 1206: 2,000 pcs/reel 1812: 1,000 pcs/reel 2 significant figures + No. of zeros 2A 4A 4. Dimension and Structure 4.1 Circuit In Out GND PAGE 1 OF 8 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. SS-227 R2 4.2 Dimension Dimensions in inches (mm) Size L W T g e 0603 0.063 (1.6 ± 0.2) 0.031 (0.8 ± 0.2) 0.024 (0.6 ± 0.2) 0.020 (0.5 ± 0.3) 0.008 (0.2 ± 0.15) 0805 0.079 (2.0 ± 0.2) 0.049 (1.25 ± 0.2) 0.031 (0.8 ± 0.2*) 0.016 (0.4 ± 0.3) 0.012 (0.3 ± 0.2) 1206 0.126 (3.2 ± 0.2) 0.063 (1.6 ± 0.2) 0.031 (0.8 ± 0.2*) 0.039 (1.0 ± 0.3) 0.016 (0.4 ± 0.3) 1812 0.177 (4.5 ± 0.3) 0.126 (3.2 ± 0.3) 0.039 (1.0 ± 0.2) 0.039 (1.0 ± 0.3) 0.016 (0.4 ± 0.3) * KGM0805 470 KGM0805 101 KGM0805 220 KGM0805 105 T: 0.035 ± (0.9 ± 0.2) KGM1206CHT221/2A: T = 0.043 (1.1 ± 0.2) L W t e g e 5. Structure Single Layer Type GND Terminals (Ag + Ni, Sn plating) Glass Coating Inner Electrode (Ag) Inner Electrode (Ag) Terminals (Ag + Ni, Sn plating) Multilayer Type GND Terminals Ceramics Terminals Inner Electrode Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 PAGE 2 OF 8 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. SS-227 R2 6. Standard Applications Part Designation Capacitance (pF) KGM0603ECTTE2202A KGM0603ECTTE4702A KGM0603ECTTE1012A KGM0603ECTTE2212A KGM0603ECTTE4712A KGM0603ECTTE1022A KGM0603CCTTE2222A KGM0603CCTTE3322A KGM0603CFTTE2232A KGM0603CFTTE1042A KGM0805HCTTE2202A KGM0805HCTTE4702A KGM0805HCTTE1012A KGM0805ECTTE2212A KGM0805ECTTE4712A KGM0805ECTTE1022A KGM0805ECTTE2222A KGM0805ECTTE3322A KGM0805EFTTE1042A KGM0805CFTTE1052A KGM1206HCTTE2202A KGM1206HCTTE4702A KGM1206HCTTE1012A KGM1206HCTTE2212A KGM1206HCTTE4712A KGM1206HCTTE1022A KGM1206VCTTE2222A KGM1206ECTTE2722A KGM1206ECTTE3322A KGM1206ECTTE1032A KGM1206EFTTE1042A KGM1812HCTTE4714A KGM1812HCTTE1024A KGM1812HCTTE2224A KGM1812ECTTE6824A 22 47 100 220 470 1000 2200 3300 22,000 100,000 22 47 100 220 470 1000 2200 3300 100,000 1,000,000 22 47 100 220 470 1000 2200 2700 3300 10,000 100,000 470 1000 2200 6800 Capacitance Tolerance (%) Rated Voltage DC (V) Rated Current DC (A) Insulation Resistance Minimum (MΩ) Operating Temperature Range 2 1000 -40°C to +85°C 2 1000 -40°C to +85°C 2 1000 -40°C to +85°C 2 1000 -40°C to +85°C 25 +50 ~ -20 16 50 +50 ~ -20 25 16 50 +50 ~ -20 35 25 50 +50 ~ -20 25 PAGE 3 OF 8 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. SS-227 R2 7. Pattern design The land pattern is recommended as follows. 0805 Chip Mounting Side Resist 1.2 2.4 0.7 0.4 0.4 ø 0.3 Through Hole 1812 Chip Mounting Side ø 0.5 Through Hole Resist 1.4 1.8 0.5 1.0 1.4 0.6 0.8 1.0 2.4 5.0 ø 0.3 Through Hole 1.4 2.8 1.2 2.4 0.6 1206 Chip Mounting Side 1.0 0603 Chip Mounting Side Resist 0603, 0805, 1206, 1812 Back Side Connect to ground pattern of mounting side 5.0 3.0 ø 0.5 Through Hole Ground Pattern 0.8 3.5 (unit: mm) 6.5 8. Characteristics Item Requirement Conditions Insulation Resistance Min 1000M ohms Applied rated voltage for 60 seconds. Capacitance Within the tolerance Frequency: 1kHz Voltage: 1Vrms DC Resistance Max 60m ohms DC: 0.3V Max. Dielectric Withstanding Strength No break down Applied 250% of the rated voltage for 1 to 5 seconds. Limit surge current 50mA max. PAGE 4 OF 8 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. SS-227 R2 8. Characteristics Cont. Item Requirement Conditions Terminal Adhesion Strength No physical damage Solder a chip to a test substrate and then laterally apply a load (5N, 500gF) in the arrow direction. Chip Substrate Soldering Heat Resistance Appearance: No physical damage Capacitance: Within tolerance Dielectric Loss: Within tolerance Insulation Resistance: Within tolerance Flux: 25% rosin Pre-heating: 60 sec Pre-heating Temp: 150°C Solder: H60A Solder Temp: 260°C ±5°C Dip Time: 5 ±0.5 sec Solderablility More than 95% of the terminal electrode shall be covered with new solder. Flux: 25% rosin Pre-heating: 60 sec Pre-heating Temp: 150°C Solder: H60A Solder Temp: 230°C ±5°C Dip Time: 4 ±1 sec Temperature Cycle Appearance: No physical damage Capacitance: Within tolerance Dielectric Loss: Within tolerance Insulation Resistance: Within tolerance Repeat the following heat cycle 10 times: Step Temperature Time 1 -40°C ±3°C 30 min ±3 min 2 Room Temp. 15 min max. 3 85°C ±2°C 30 min ±3 min 4 Room Temp. 15 min max. High Temperature Resistance Appearance: No physical damage Capacitance: Within tolerance Dielectric Loss: Within tolerance Insulation Resistance: Within tolerance Temp: 70°C ±2°C Bias: 150% of rated voltage Test Time: 1000+48/-0 hour Humidity Resistance (unload) Appearance: No physical damage Capacitance: Within tolerance Dielectric Loss: Within tolerance Insulation Resistance: Within tolerance Temp: 85°C ±2°C Humidity: 85% ±5% Test Time: 500+24/-0 hour Vending Substrate Appearance: No physical damage Capacitance: Within tolerance After soldering a chip to a test substrate, bend the substrate by 1 mm and then measure. The substrate is GE4 20 or based on GE4. Substrate Weight Displacement 45 ± 2 45 ± 2 PAGE 5 OF 8 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. SS-227 R2 8. Characteristics Cont. Item Requirement Conditions Humidity Resistance (load) Appearance: No physical damage Capacitance: Within tolerance Dielectric Loss: Within tolerance Insulation Resistance: Within tolerance Temp: 40°C ±2°C Humidity: 90 - 95% Bias: 100% of rated voltage Test Time: 500+24/-0 hour Low Temperature Resistance (unload) Appearance: No physical damage Capacitance: Within tolerance Dielectric Loss: Within tolerance Insulation Resistance: Within tolerance Temp: -40°C ±2°C Test Time: 1000+48/-0 hour Vibration Appearance: No physical damage Capacitance: Within tolerance Dielectric Loss: Within tolerance Insulation Resistance: Within tolerance The frequency of applied vibration should be swept from 10 Hz to 55 Hz and return to 10 Hz. This cycle time should be about 1 min and this cycle should be repeated. Amplitude (total Excursion): 1.5 mm This motion shall be applied for period of 2 hours in each 3 mutually perpendicular axes. (total of 6 hours) After Temperature cycle test, High temperature resistance test, Humidity resistance test or Low temperature resistance test, the tested sample should be measured after having left in temperature from 15° to 35°C and relative humidity from 45% to 75% for 24 hours. 9. Packaging Specifications 9.1 Taping Packaging of components on continuous tape is complete with carrier tape for putting components and cover tape for sealing. (1) Dimensions of Carrier Tape 15.75 (400) 6.30 (160) 6.30 (160) Top tape Empty Empty Tape running direction PAGE 6 OF 8 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. SS-227 R2 9-1 Taping Cont. Taping shape in accordance with EIAJ RC-1009B Dimensions in inches (mm) (2) Dimensions of Embossed Carrier Tape Feeding Hole Chip Pocket D0 t1 E F B W A P1 t2 P2 P3 Dimensions in inches (mm) Series A B W F E P1 KGM0603 0.043 ± 0.002 0.075 ± 0.002 0.314 ± 0.003 0.137 ± 0.002 0.068 ± 0.003 0.157 ± 0.003 Series (1.1 ± 0.05) (1.9 ± 0.05) (8.0 ± 0.1) (3.5 ± 0.05) (1.75 ± 0.1) (4.0 ± 0.1) KGM0805 0.061 ± 0.003 0.091 ± 0.003 0.314 ± 0.008 0.137 ± 0.002 0.068 ± 0.003 0.157 ± 0.003 Series (1.55 ± 0.1) (2.3 ± 0.1) (8.0 ± 0.2) (3.5 ± 0.05) (1.75 ± 0.1) (4.0 ± 0.1) KGM1206 0.078 ± 0.003 0.137 ± 0.003 0.314 ± 0.011 0.137 ± 0.002 0.068 ± 0.003 0.157 ± 0.003 Series (2.0 ± 0.1) (3.5 ± 0.1) (8.0 ± 0.3) (3.5 ± 0.05) (1.75 ± 0.1) (4.0 ± 0.1) KGM1812 0.137 ± 0.007 0.192 ± 0.003 0.472 ± 0.011 0.216 ± 0.002 0.068 ± 0.003 0.157 ± 0.003 Series (3.5 ± 0.2) (4.9 ± 0.1) (12.0 ± 0.3) (5.5 ± 0.05) (1.75 ± 0.1) (4.0 ± 0.1) Dimensions in inches (mm) Series P2 P3 KGM0603 0.078 ± 0.02 0.157 ± 0.003 Series (2.0 ± 0.05) (4.0 ± 0.1) D0 0.059...+ 0.003 -0.... + 0.1 (1.5 -0 ) t1 0.011 ± 0.001 (0.3 ± 0.05) t2 0.098 (2.5 max) KGM0805 0.078 ± 0.02 0.157 ± 0.003 Series (2.0 ± 0.05) (4.0 ± 0.1) 0.059...+ 0.003 -0.... (1.5 + -00.1 ) 0.011 ± 0.001 (0.3 ± 0.05) 0.098 (2.5 max) KGM1206 0.078 ± 0.02 0.157 ± 0.003 Series (2.0 ± 0.05) (4.0 ± 0.1) 0.059...+ 0.003 .... -0 + 0.1 (1.5 -0 ) 0.011 ± 0.001 (0.3 ± 0.05) 0.098 (2.5 max) KGM1812 0.078 ± 0.02 0.157 ± 0.003 Series (2.0 ± 0.05) (4.0 ± 0.1) 0.059...+ 0.003 .... -0 + 0.1 (1.5 -0 ) 0.011 ± 0.001 (0.3 ± 0.05) 0.098 (2.5 max) Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 PAGE 7 OF 8 ■ Fax 814-362-8883 ■ www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. SS-227 R2 (2) Reel specifications for taping (3) Standard Packing Quantity E C D B A Series Name KGM0603 Series Quantity 4,000 pcs/reel KGM0805 Series 4,000 pcs/reel KGM1206 Series 2,000 pcs/reel KGM1812 Series 1,000 pcs/reel W Dimensions in inches (mm) Series 0603 0805 1206 A 7.00 ± 0.78 (178 ± 2) B 2.36 (60 min) C D +0.02 0.511 -0.008 . (13 +0.5 ) -0.2 E 0.83 ± 0.03 (21 ± 0.8) 1812 W (min) W (max) 0.429 ± 0.059 0.311 ± 0.059 (10.9 ± 1.5) 0.079 ± 0.02 (7.9 ± 1.5) –––– (2 ± 0.5) 0.468 ± 0.059 0.606 ± 0.059 (11.9 ± 1.5) (15.4 ± 1.5) Flux shall be Rosin type. Do not use strong acid type fluxes. 10. Soldering KOA filters have Ag (or Ag-Pd) Ni barrier terminals, overplated with Sn for use in either wave or reflow soldering processes. The tip of soldering iron should be 20 W. 3 mmø maximum. Ceramics are very sensitive in general to thermal shock. Therefore KOA filters should not be exposed to sudden temperature increases or partial heating. The tip of soldering iron should be 220 250°C maximum. Care must be taken not to physically damage the chip through abnormal contact with soldering irons. Prior to soldering, KOA filters shall be preheated so that the temperature difference during soldering will be kept within 130°C. It is desirable that soldering temperature be kept to 240 ~ 250°C and soldering time be within 4 seconds. PAGE 8 OF 8 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.