KCR three-terminal capacitor/resistor EU features • • • • • Improved reduction of radiated noises Capacitor/resistor filter Noise reduction in a variety of circuits Marking: Black body color with no marking Products with lead-free terminations meet EU RoHS requirements dimensions and construction L Size W 1206 Terminals (Ag + Ni, Sn Plating) t Glass Coating e g GND Terminals (Ag + Ni, Sn Plating) L W t g e .126±.008 .063±.008 .031±.008 .039±.012 .016±.012 (3.2±0.2) (1.6±0.2) (0.8±0.2)* (1.0±0.3) (0.4±0.3) * KCR1206T221/500: t = .043 ± .008 (1.1 ± 0.2) KCR1206T221/101: t = .043 ± .008 (1.1 ± 0.2) e ordering information New Part # EMI/EMC filtering KCR 1206 Type Size 1206 T Termination Material T: Sn TE Packaging TE: 7" embossed plastic (1206 - 2,000 pieces/reel) 220/500 Capacitance/ Resistance 2 significant digits + number of zeros For further information on packaging, please refer to Appendix A. Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. 276 2/24/08 KOA Speer Electronics, Inc. • Bolivar Drive • P.O. Box 547 • Bradford, PA 16701 • USA • 814-362-5536 • Fax: 814-362-8883 • www.koaspeer.com KCR three-terminal capacitor/resistor circuit schematic In applications and ratings Out GND Item Specification Operating Temperature Range Storage Temperature Range Measuring Condition (Standard) Temperature Relative Humidity Measuring Condition (Precision) Temperature Relative Humidity -40°C to +85°C -40°C to +85°C 15°C to 35°C 20 - 90% 20°C ± 1°C 60 - 67% applications and ratings (continued) Part Designation Capacitance (pF) KCR1206TTE220/500 KCR1206TTE220/101 KCR1206TTE470/500 KCR1206TTE470/101 KCR1206TTE101/500 KCR1206TTE101/101 KCR1206TTE221/500 KCR1206TTE221/101 22 22 47 47 100 100 220 220 Capacitance Tolerance Resistance (Ω) Resistance Tolerance (%) Power Rating (W) Operating Temperature Range +50 ~ -20 50 100 50 100 50 100 50 100 ±30 1/16 -40°C to +85°C environmental applications Performance Characteristics Test Method Insulation Resistance 1000 MΩ Minimum Applied rated voltage for 60 seconds Capacitance Within the tolerance Frequency: 1kHz Voltage: 1Vrms DC Resistance Within the tolerance DC: 0.3V Maximum Terminal Adhesion Strength No physical damage Solder a chip to a test substrate and then laterally apply a load (5N, 500gF) in the arrow direction Chip EMI/EMC filtering Requirement Parameter Substrate Resistance to Solder Heat Appearance: No physical damage Capacitance: Within tolerance Dielectric Loss: Within tolerance Insulation Resistance: Within tolerance Flux: 25% rosin Preheating: 60 seconds Preheating Temperature: 150°C Solder: H60A Solder Temperature: 260°C ±5°C Dip Time: 5 seconds ± 0.5 second Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. 5/15/05 KOA Speer Electronics, Inc. • Bolivar Drive • P.O. Box 547 • Bradford, PA 16701 • USA • 814-362-5536 • Fax: 814-362-8883 • www.koaspeer.com 277 KCR three-terminal capacitor/resistor environmental applications (continued) Performance Characteristics Parameter Requirement Test Method Solderability More than 95% of the terminal electrode shall be covered with new solder Flux: 25% rosin Preheating: 60 seconds Preheating Temperature: 150°C Solder: H60A Solder Temperature: 230°C ±5°C Dip Time: 4 seconds ± 1 second Temperature Cycle* Appearance: No physical damage Capacitance: Within tolerance Dielectric Loss: Within tolerance Insulation Resistance: Within tolerance Repeat the following heat cycle 10 times: High Temperature Resistance* Appearance: No physical damage Capacitance: Within tolerance Dielectric Loss: Within tolerance Insulation Resistance: Within tolerance Temperature: 70°C ± 2°C Bias: 150% of rated voltage Test Time: 1000 +48/-0 hours Humidity Resistance (Unload)* Appearance: No physical damage Capacitance: Within tolerance Dielectric Loss: Within tolerance Insulation Resistance: Within tolerance Temperature: 85°C ± 2°C Humidity: 85% ± 5% Test Time: 500 +24/-0 hours Substrate Bending Test Appearance: No physical damage Capacitance: Within tolerance After soldering a chip to a test substrate, bend the substrate by 1 mm and then measure. The substrate is GE4 or based on GE4. 20 Step: 1 2 3 4 Temperature: -40°C ± 3°C Room Temp. 85°C ± 2°C Room Temp. Time: 30 minutes 15 minutes 30 minutes 15 minutes Substrate ± 3 minutes maximum ± 3 minutes maximum Weight Displacement 45 ± 2 45 ± 2 EMI/EMC filtering Humidity Resistance (Load)* Appearance: No physical damage Capacitance: Within tolerance Dielectric Loss: Within tolerance Insulation Resistance: Within tolerance Temperature: 40°C ± 2°C Humidity: 90 - 95% Bias: 100% of rated voltage Test Time: 500 +24/-0 hours Low Temperature Resistance (Unload)* Appearance: No physical damage Capacitance: Within tolerance Dielectric Loss: Within tolerance Insulation Resistance: Within tolerance Temperature: -40°C ± 2°C Test Time: 1000 +48/-0 hours Vibration Appearance: No physical damage Capacitance: Within tolerance Dielectric Loss: Within tolerance Insulation Resistance: Within tolerance The frequency of applied vibration should be swept from 10 Hz to 55 Hz and return to 10 Hz. This cycle time should be about 1 minute and this cycle should be repeated. Amplitude (Total Excursion): 1.5 mm This motion shall be applied for a period of 2 hours in each of 3 mutually perpendicular axes (total of 6 hours). * After temperature cycle test, high temperature resistance test, humidity resistance test or low temperature resistance test, the tested sample should be measured after having been left in temperature from 15°C to 35°C and relative humidity from 45% to 75% for 24 hours. Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. 278 11/01/03 KOA Speer Electronics, Inc. • Bolivar Drive • P.O. Box 547 • Bradford, PA 16701 • USA • 814-362-5536 • Fax: 814-362-8883 • www.koaspeer.com