LT3958 High Input Voltage, Boost, Flyback, SEPIC and Inverting Converter DESCRIPTION FEATURES n n n n n n n n n n n Wide Input Voltage Range: 5V to 80V Single Feedback Pin for Positive or Negative Output Voltage Internal 3.3A/84V Power Switch Current Mode Control Provides Excellent Transient Response Programmable Operating Frequency (100kHz to 1MHz) with One External Resistor Synchronizeable to an External Clock Low Shutdown Current < 1μA Internal 7.2V Low Dropout Voltage Regulator Programmable Input Undervoltage Lockout with Hysteresis Programmable Soft-Start Thermally Enhanced QFN (5mm × 6mm) Package The LT®3958 is a wide input range, current mode, DC/DC converter which is capable of generating either positive or negative output voltages. It can be configured as either a boost, flyback, SEPIC or inverting converter. It features an internal low side N-channel power MOSFET rated for 84V at 3.3A and driven from an internal regulated 7.2V supply. The fixed frequency, current-mode architecture results in stable operation over a wide range of supply and output voltages. The operating frequency of LT3958 can be set with an external resistor over a 100kHz to 1MHz range, and can be synchronized to an external clock using the SYNC pin. A minimum operating supply voltage of 5V, and a low shutdown quiescent current of less than 1μA, make the LT3958 ideally suited for battery-powered systems. The LT3958 features soft-start and frequency foldback functions to limit inductor current during start-up. APPLICATIONS n n n Automotive Telecom Industrial L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks and No RSENSE and ThinSOT are trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. Patents pending. TYPICAL APPLICATION High Efficiency Boost Converter Efficiency vs Output Current VIN 12V TO 40V 4.7μF VIN 392k 4.7μF s2 SW GND EN/UVLO 53.6k LT3958 SGND SENSE1 SYNC SENSE2 464k VOUT 48V 0.5A 100 VIN = 24V 95 EFFICIENCY (%) 33μH 90 85 80 FBX RT 41.2k 300kHz SS INTVCC VC 0.33μF 10k 15.8k 4.7μF 75 70 0 10nF 400 100 200 300 OUTPUT CURRENT (mA) 500 3958 TA01b 3958 TA01a 3958f 1 LT3958 ABSOLUTE MAXIMUM RATINGS PIN CONFIGURATION (Note 1) VC FBX SS RT SYNC NC NC TOP VIEW 36 35 34 33 32 31 30 NC 1 28 INTVCC 27 VIN NC 2 SENSE2 3 37 SGND SGND 4 25 EN/UVLO 24 SGND 23 SGND SENSE1 6 38 SW SW 8 SW 9 21 SW 20 SW NC 10 GND GND GND GND GND 12 13 14 15 16 17 GND VIN, EN/UVLO (Note 5) ..............................................80V SW ............................................................................84V INTVCC .................................................... VIN + 0.3V, 15V SYNC ..........................................................................8V VC, SS.........................................................................3V RT ............................................................................................... 1.5V SENSE1, SGND .................. Internally Connected to GND SENSE2..................................................................±0.3V FBX ................................................................. –6V to 6V Operating Temperature Range (Note 2) ............................................. –40°C to 125°C Maximum Junction Temperature........................... 125°C Storage Temperature Range................... –65°C to 125°C UHE PACKAGE 36-LEAD (5mm s 6mm) PLASTIC QFN TJMAX = 125°C, θJA = 43°C/W, θJC = 5°C/W EXPOSED PAD (PIN 37) IS SGND, MUST BE SOLDERED TO SGND PLANE EXPOSED PAD (PIN 38) IS SW, MUST BE SOLDERED TO SW PLANE ORDER INFORMATION LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LT3958EUHE#PBF LT3958EUHE#TRPBF 3958 36-Lead (5mm × 6mm) Plastic QFN –40°C to 125°C LT3958IUHE#PBF LT3958IUHE#TRPBF 3958 36-Lead (5mm × 6mm) Plastic QFN –40°C to 125°C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ 3958f 2 LT3958 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. VIN = 24V, EN/UVLO = 24V, SENSE2 = 0V, unless otherwise noted. PARAMETER CONDITIONS MIN VIN Operating Range TYP 5 MAX UNITS 80 V VIN Shutdown IQ EN/UVLO = 0V EN/UVLO = 1.15V 0.1 1 6 μA μA VIN Operating IQ VC = 0.3V, RT = 41.2k 1.6 2.2 mA VIN Operating IQ with Internal LDO Disabled VC = 0.3V, RT = 41.2k, INTVCC = 7.5V 350 400 μA SW Pin Current Limit SENSE2 = SENSE1 4.0 4.6 A SW Pin On Voltage ISW = 2A 180 mV SENSE2 Input Bias Current Current Out of Pin –65 μA l 3.3 Error Amplifier FBX Regulation Voltage (VFBX(REG)) FBX > 0V (Note 3) FBX < 0V (Note 3) FBX Overvoltage Lockout FBX > 0V (Note 4) FBX < 0V (Note 4) FBX Pin Input Current FBX = 1.6V (Note 3) FBX = –0.8V (Note 3) l l 1.569 –0.816 1.6 –0.800 1.631 –0.784 V V 6 7 8 11 10 14 % % 70 100 10 nA nA –10 Transconductance gm (ΔIVC /ΔFBX) (Note 3) 230 μS VC Output Impedance (Note 3) 5 MΩ VFBX Line Regulation (ΔVFBX /[ΔVIN • VFBX(REG)]) FBX > 0V, 5V < VIN < 80V (Notes 3, 6) FBX < 0V, 5V < VIN < 80V (Notes 3, 6) 0.006 0.005 VC Current Mode Gain (ΔVVC /ΔVSENSE) 0.03 0.038 %/V %/V 10 V/V VC Source Current VC = 1.5V, FBX = 0V, Current Out of Pin –15 μA VC Sink Current FBX = 1.7V FBX = –0.85V 12 11 μA μA Oscillator Switching Frequency RT = 140k to SGND, FBX = 1.6V, VC = 1.5V RT = 41.2k to SGND, FBX = 1.6V, VC = 1.5V RT = 10.5k to SGND, FBX = 1.6V, VC = 1.5V RT Voltage FBX = 1.6V 80 270 850 100 300 1000 120 330 1200 1.2 kHz kHz kHz V SW Minimum Off-Time 200 275 ns SW Minimum On-Time 250 300 ns SYNC Input Low 0.4 SYNC Input High SS Pull-Up Current 1.5 SS = 0V, Current Out of Pin –10 μA Low Dropout Regulator l INTVCC Regulation Voltage INTVCC Undervoltage Lockout Threshold INTVCC Overvoltage Lockout Threshold Falling INTVCC UVLO Hysteresis 7 7.2 7.4 V 3.55 3.75 0.15 4.00 V V 11.5 12.8 V 3958f 3 LT3958 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. VIN = 24V, EN/UVLO = 24V, SENSE2 = 0V, unless otherwise noted. PARAMETER CONDITIONS MIN TYP MAX INTVCC Current Limit VIN = 80V VIN = 20V 19 24 50 29 INTVCC Load Regulation (ΔVINTVCC / VINTVCC) 0 < IINTVCC < 10mA, VIN = 8V –1 –0.4 INTVCC Line Regulation (ΔVINTVCC / [ΔVIN • VINTVCC]) 8V < VIN < 80V UNITS mA mA % 0.005 0.025 %/V Dropout Voltage (VIN – VINTVCC) VIN = 6V, IINTVCC = 10mA, VC = 0V 500 mV INTVCC Current in Shutdown EN/UVLO = 0V, INTVCC = 8V 16 μA INTVCC Voltage to Bypass Internal LDO 7.5 V Logic Inputs l VIN = INTVCC = 8V EN/UVLO Threshold Voltage Falling 1.17 EN/UVLO Voltage Hysteresis IVIN Drops Below 1μA EN/UVLO Pin Bias Current Low EN/UVLO = 1.15V EN/UVLO Pin Bias Current High EN/UVLO = 1.33V Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The LT3958E is guaranteed to meet performance specifications from the 0°C to 125°C junction temperature. Specifications over the –40°C to 125°C operating junction temperature range are assured by design, characterization and correlation with statistical process controls. The LT3958I is guaranteed over the full –40°C to 125°C operating junction temperature range. 1.7 Positive Feedback Voltage vs Temperature, VIN VIN = 8V 1.596 1.594 VIN = INTVCC = 5V 1.592 –25 50 25 0 75 TEMPERATURE (°C) 100 125 3958 G01 –794 VIN = INTVCC = 5V –796 VIN = 8V –798 –800 2 2.5 μA 10 100 nA 1.8 QUIESCENT CURRENT (mA) REGULATED FEEDBACK VOLTAGE (mV) REGULATED FEEDBACK VOLTAGE (V) VIN = 24V 1.598 V Quiescent Current vs Temperature, VIN –792 VIN = 80V 0.4 TA = 25°C, unless otherwise noted. Negative Feedback Voltage vs Temperature, VIN 1.604 1.590 –50 V mV Note 3: The LT3958 is tested in a feedback loop which servos VFBX to the reference voltages (1.6V and –0.8V) with the VC pin forced to 1.3V. Note 4: FBX overvoltage lockout is measured at VFBX(OVERVOLTAGE) relative to regulated VFBX(REG). Note 5: For 5V < VIN < 6V, the EN/UVLO pin must not exceed VIN. Note 6: EN/UVLO = 1.33V when VIN = 5V. TYPICAL PERFORMANCE CHARACTERISTICS 1.600 1.27 20 EN/UVLO Input Low Voltage 1.602 1.22 VIN = 24V VIN = 80V VIN = 80V 1.7 VIN = 24V 1.6 VIN = INTVCC = 5V 1.5 –802 –804 –50 –25 50 25 0 75 TEMPERATURE (°C) 100 125 3958 G02 1.4 –50 –25 50 25 0 75 TEMPERATURE (°C) 100 125 3958 G03 3958f 4 LT3958 TYPICAL PERFORMANCE CHARACTERISTICS Dynamic Quiescent Current vs Switching Frequency TA = 25°C, unless otherwise noted. Normalized Switching Frequency vs FBX RT vs Switching Frequency 12 120 1000 NORMALIZED FREQUENCY (%) 10 RT (kΩ) IQ(mA) 8 6 100 4 2 0 100 200 300 400 500 600 700 800 900 1000 SWITCHING FREQUENCY (kHz) 10 315 310 305 300 295 290 285 0 25 50 75 TEMPERATURE (°C) 100 4.4 4.4 4.3 4.3 4.2 4.1 4.0 3.9 3.8 1.26 40 50 25 0 75 TEMPERATURE (°C) 100 50 25 0 75 TEMPERATURE (°C) 3.8 0 100 125 3958 G10 20 40 60 DUTY CYCLE (%) 80 100 3958 G09 2.4 2.2 30 20 2.0 1.8 0 –25 3.9 EN/UVLO Hysteresis Current vs Temperature 10 1.20 1.18 –50 4.0 125 IEN/UVLO (μA) EN/UVLO CURRENT (μA) EN/UVLO VOLTAGE (V) 50 1.22 4.1 EN/UVLO Current vs Voltage 1.28 1.6 4.2 3958 G08 EN/UVLO Threshold vs Temperature EN/UVLO FALLING 1.2 3.6 –25 3958 G07 1.24 0 0.4 0.8 FBX VOLTAGE (V) 3.7 3.6 –50 125 EN/UVLO RISING –0.4 SW Pin Current Limit vs Duty Cycle 3.7 280 –25 20 3958 G06 SW PIN CURRENT LIMIT (A) RT = 41.2k 275 –50 40 SW Pin Current Limit vs Temperature SW PIN CURRENT LIMIT (A) SWITCHING FREQUENCY (kHz) 320 60 3958 G05 Switching Frequency vs Temperature 325 80 0 –0.8 0 100 200 300 400 500 600 700 800 900 1000 SWITCHING FREQUENCY (kHz) 3958 G04 100 0 20 40 60 EN/UVLO VOLTAGE (V) 80 3958 G11 1.6 –50 –25 50 25 0 75 TEMPERATURE (°C) 100 125 3958 G12 3958f 5 LT3958 TYPICAL PERFORMANCE CHARACTERISTICS INTVCC vs Temperature 7.30 VIN = 8V INTVCC VOLTAGE (V) 7.2 INTVCC VOLTAGE (V) 7.2 7.3 INTVCC (V) INTVCC Line Regulation INTVCC Load Regulation 7.3 7.4 7.1 7 7.25 7.20 7.15 7.1 6.9 7.0 –50 7.10 6.8 50 25 0 75 TEMPERATURE (°C) –25 100 125 0 5 20 15 10 INTVCC LOAD (mA) INTVCC Dropout Voltage vs Current, Temperature 180 125°C 160 700 140 ON-RESISTANCE (mΩ) 800 75°C 600 25°C 500 400 0°C 300 –40°C 200 0 4 6 8 30 40 50 VIN (V) 60 70 80 3958 G15 102 100 120 100 80 60 98 96 94 92 90 20 2 20 40 100 0 10 Internal Switch On-Resistance vs INTVCC Internal Switch On-Resistance vs Temperature ON-RESISTANCE (mΩ) 900 0 25 3958 G14 3958 G13 DROPOUT VOLTAGE (mV) TA = 25°C, unless otherwise noted. 10 0 –50 –25 0 25 50 75 100 125 88 4 5 6 7 TEMPERATURE (°C) INTVCC LOAD (mA) 3958 G17 3958 G16 SEPIC Typical Start-Up Waveforms 8 9 10 11 12 INTVCC (V) 3958 G18 SEPIC FBX Frequency Foldback Waveforms During Overcurrent VIN = 24V VIN = 24V VOUT 10V/DIV VOUT 5V/DIV VSW 20V/DIV IL1A + IL1B 2A/DIV IL1A + IL1B 2A/DIV 5ms/DIV 3958 G19 SEE TYPICAL APPLICATION: 10V TO 60V INPUT, 12V OUTPUT SEPIC CONVERTER 50μs/DIV 3958 G20 SEE TYPICAL APPLICATION: 10V TO 60V INPUT, 12V OUTPUT SEPIC CONVERTER 3958f 6 LT3958 PIN FUNCTIONS NC (Pins 1, 2, 10, 35, 36): No Internal Connection. Leave these pins open or connect them to the adjacent pins. SENSE2 (Pin 3): The Current Sense Input for the Control Loop. Connect this pin to SENSE1 pin directly or through a low pass filter (connect this pin to SENSE1 pin through a resistor, and to SGND through a capacitor). SGND (Pins 4, 23, 24, Exposed Pad Pin 37): Signal Ground. All small-signal components should connect to this ground. SGND is connected to GND inside the IC to ensure Kelvin connection for the internal switch current sensing. Do not connect SGND and GND externally. SENSE1 (Pin 6): The Current Sense Output of the Internal N-channel MOSFET. Connect this pin to SENSE2 pin directly or through a low pass filter (connect this pin to SENSE1 pin through a resistor, then connect SENSE2 to SGND through a capacitor). SW (Pins 8,9,20,21, Exposed Pad Pin 38): Drain of Internal Power N-channel MOSFET. GND (Pins 12,13,14,15,16,17): Ground. These pins connect to the source terminal of internal power N-channel MOSFET through an internal sense resistor. GND is connected to SGND inside the IC to ensure Kelvin connection for the internal switch current sensing. Do not connect GND and SGND externally. EN/UVLO (Pin 25): Shutdown and Undervoltage Detect Pin. An accurate 1.22V (nominal) falling threshold with externally programmable hysteresis detects when power is okay to enable switching. Rising hysteresis is generated by the external resistor divider and an accurate internal 2μA pull-down current. An undervoltage condition resets sort-start. Tie to 0.4V, or less, to disable the device and reduce VIN quiescent current below 1μA. VIN (Pin 27): Input Supply Pin. VIN pin can be locally bypassed with a capacitor to GND (not SGND). INTVCC (Pin 28): Regulated Supply for Internal Loads and Gate Driver. Supplied from VIN and regulated to 7.2V (typical). INTVCC must be bypassed to SGND with a minimum of 4.7μF capacitor placed close to pin. INTVCC can be connected directly to VIN, if VIN is less than 11.5V. INTVCC can also be connected to a power supply whose voltage is higher than 7.5V, and lower than VIN, provided that supply does not exceed 11.5V. VC (Pin 30): Error Amplifier Compensation Pin. Used to stabilize the voltage loop with an external RC network. Place compensation components between the VC pin and SGND. FBX (Pin 31): Positive and Negative Feedback Pin. Receives the feedback voltage from the external resistor divider between the output and SGND. Also modulates the switching frequency during start-up and fault conditions when FBX is close to SGND. SS (Pin 32): Soft-Start Pin. This pin modulates compensation pin voltage (VC) clamp. The soft-start interval is set with an external capacitor between SS pin and SGND. The pin has a 10μA (typical) pull-up current source to an internal 2.5V rail. The soft-start pin is reset to SGND by an undervoltage condition at EN/UVLO, an INTVCC undervoltage or overvoltage condition or an internal thermal lockout. RT (Pin 33): Switching Frequency Adjustment Pin. Set the frequency using a resistor to SGND. Do not leave this pin open. SYNC (Pin 34): Frequency Synchronization Pin. Used to synchronize the switching frequency to an outside clock. If this feature is used, an RT resistor should be chosen to program a switching frequency 20% slower than the SYNC pulse frequency. Tie the SYNC pin to SGND if this feature is not used. SYNC is ignored when FBX is close to SGND. 3958f 7 LT3958 BLOCK DIAGRAM CDC L1 R4 R3 L2 EN/UVLO A10 IS1 2μA IS2 10μA – + 1.72V – + 27 12.8V + – UVLO A9 G3 A8 IS3 A11 TLO 165˚C CURRENT LIMIT 7.2V LDO –0.88V A12 VC Q2 1.6V INTVCC 28 + – CVCC DRIVER SR1 – +A7 G5 R G2 O M1 S 6 PWM COMPARATOR + A1 – RSENSE VISENSE SLOPE – A6 + –0.8V RAMP 1.28V RAMP GENERATOR – +A3 + + – 31 FBX 30 VC 32 SS 34 SYNC + – A4 CC2 RC CSS 3 SENSE2 Q1 FREQ PROG 33 RT SGND 4, 23, 24, 37 R2 VOUT 12, 13, 14, 15, 16, 17 100kHz-1MHz OSCILLATOR G1 FREQUENCY 1.2V FOLDBACK FREQUENCY FOLDBACK A5 SENSE1 GND 48mV SENSE + A2 – INTVCC 3.75V G6 – + SW 1.22V INTERNAL REGULATOR AND UVLO G4 VIN COUT • 8, 9, 20, 21, 38 Q3 2.5V VOUT CIN 25 2.5V D1 • VIN 3958 F01 RT R1 CC1 Figure 1. LT3958 Block Diagram Working as a SEPIC Converter 3958f 8 LT3958 APPLICATIONS INFORMATION Main Control Loop The LT3958 uses a fixed frequency, current mode control scheme to provide excellent line and load regulation. Operation can be best understood by referring to the Block Diagram in Figure 1. The start of each oscillator cycle sets the SR latch (SR1) and turns on the internal power MOSFET switch M1 through driver G2. The switch current flows through the internal current sensing resistor RSENSE and generates a voltage proportional to the switch current. This current sense voltage VISENSE (amplified by A5) is added to a stabilizing slope compensation ramp and the resulting sum (SLOPE) is fed into the positive terminal of the PWM comparator A7. When SLOPE exceeds the level at the negative input of A7 (VC pin), SR1 is reset, turning off the power switch. The level at the negative input of A7 is set by the error amplifier A1 (or A2) and is an amplified version of the difference between the feedback voltage (FBX pin) and the reference voltage (1.6V or –0.8V, depending on the configuration). In this manner, the error amplifier sets the correct peak switch current level to keep the output in regulation. The LT3958 has a switch current limit function. The current sense voltage is input to the current limit comparator A6. If the SENSE2 pin voltage is higher than the sense current limit threshold VSENSE(MAX) (48mV, typical), A6 will reset SR1 and turn off M1 immediately. The LT3958 is capable of generating either positive or negative output voltage with a single FBX pin. It can be configured as a boost, flyback or SEPIC converter to generate positive output voltage, or as an inverting converter to generate negative output voltage. When configured as a SEPIC converter, as shown in Figure 1, the FBX pin is pulled up to the internal bias voltage of 1.6V by a voltage divider (R1 and R2) connected from VOUT to SGND. Comparator A2 becomes inactive and comparator A1 performs the inverting amplification from FBX to VC. When the LT3958 is in an inverting configuration, the FBX pin is pulled down to –0.8V by a voltage divider connected from VOUT to SGND. Comparator A1 becomes inactive and comparator A2 performs the noninverting amplification from FBX to VC. The LT3958 has overvoltage protection functions to protect the converter from excessive output voltage overshoot during start-up or recovery from a short-circuit condition. An overvoltage comparator A11 (with 20mV hysteresis) senses when the FBX pin voltage exceeds the positive regulated voltage (1.6V) by 8% and provides a reset pulse. Similarly, an overvoltage comparator A12 (with 10mV hysteresis) senses when the FBX pin voltage exceeds the negative regulated voltage (–0.8V) by 11% and provides a reset pulse. Both reset pulses are sent to the main RS latch (SR1) through G6 and G5. The power MOSFET switch M1 is actively held off for the duration of an output overvoltage condition. Programming Turn-On and Turn-Off Thresholds with the EN/UVLO Pin The EN/UVLO pin controls whether the LT3958 is enabled or is in shutdown state. A micropower 1.22V reference, a comparator A10 and a controllable current source IS1 allow the user to accurately program the supply voltage at which the IC turns on and off. The falling value can be accurately set by the resistor dividers R3 and R4. When EN/UVLO is above 0.4V, and below the 1.22V threshold, the small pull-down current source IS1 (typical 2μA) is active. The purpose of this current is to allow the user to program the rising hysteresis. The Block Diagram of the comparator and the external resistors is shown in Figure 1. The typical falling threshold voltage and rising threshold voltage can be calculated by the following equations: (R3 + R4) R4 VVIN,RISING = 2µA • R3 + VIN,FALLING VVIN,FALLING = 1.22 • For applications where the EN/UVLO pin is only used as a logic input, the EN/UVLO pin can be connected directly to the input voltage VIN through a 1k resistor for alwayson operation. 3958f 9 LT3958 APPLICATIONS INFORMATION INTVCC Regulator Bypassing and Operation An internal, low dropout (LDO) voltage regulator produces the 7.2V INTVCC supply which powers the gate driver, as shown in Figure 1. The LT3958 contains an undervoltage lockout comparator A8 and an overvoltage lockout comparator A9 for the INTVCC supply. The INTVCC undervoltage (UV) threshold is 3.75V (typical), with 0.15V hysteresis, to ensure that the internal MOSFET has sufficient gate drive voltage before turning on. The logic circuitry within the LT3958 is also powered from the internal INTVCC supply. The INTVCC overvoltage threshold is set to be 12.8V (typical) to protect the gate of the power MOSFET. When INTVCC is below the UV threshold, or above the overvoltage threshold, the internal power switch will be turned off and the soft-start operation will be triggered. The INTVCC regulator must be bypassed to SGND immediately adjacent to the IC pins with a minimum of 4.7μF ceramic capacitor. Good bypassing is necessary to supply the high transient currents required by the MOSFET gate driver. In an actual application, most of the IC supply current is used to drive the gate capacitance of the internal power MOSFET. The on-chip power dissipation can be significant when the internal power MOSFET is being driven at a high frequency and the VIN voltage is high. An effective approach to reduce the power consumption of the internal LDO for gate drive and to improve the efficiency is to tie the INTVCC pin to an external voltage source high enough to turn off the internal LDO regulator. If the input voltage VIN does not exceed the INTVCC overvoltage lockout threshold voltage (12.8V), the INTVCC pin can be shorted directly to the VIN pin. In this condition, the internal LDO will be turned off and the gate driver will be powered directly from the input voltage VIN. With the INTVCC pin shorted to VIN, however, a small current (around 16μA) will load the INTVCC in shutdown mode. For applications that require the lowest shutdown mode input supply current, do not connect the INTVCC pin to VIN. In SEPIC or flyback applications, the INTVCC pin can be connected to the output voltage VOUT through a blocking diode, as shown in Figure 2, if VOUT meets the following conditions: 1. VOUT < VIN (pin voltage) 2. VOUT < 12.8V (typical) A resistor RVCC can be connected, as shown in Figure 2, to limit the inrush current from VOUT. Regardless of whether or not the INTVCC pin is connected to an external voltage source, it is always necessary to have the driver circuitry bypassed with a 4.7μF low ESR ceramic capacitor to ground immediately adjacent to the INTVCC and SGND pins. DVCC INTVCC LT3958 RVCC VOUT CVCC 4.7μF SGND 3958 F02 Figure 2. Connecting INTVCC to VOUT 3958f 10 LT3958 APPLICATIONS INFORMATION Operating Frequency and Synchronization Duty Cycle Consideration The choice of operating frequency may be determined by on-chip power dissipation (a low switching frequency may be required to ensure IC junction temperature does not exceed 125°C), otherwise it is a trade-off between efficiency and component size. Low frequency operation improves efficiency by reducing gate drive current and MOSFET and diode switching losses. However, lower frequency operation requires a physically larger inductor. Switching frequency also has implications for loop compensation. The LT3958 uses a constant-frequency architecture that can be programmed over a 100kHz to 1000kHz range with a single external resistor from the RT pin to ground, as shown in Figure 1. The RT pin must have an external resistor to SGND for proper operation of the LT3958. A table for selecting the value of RT for a given operating frequency is shown in Table 1. Switching duty cycle is a key variable defining converter operation. As such, its limits must be considered. Minimum on-time is the smallest time duration that the LT3958 is capable of turning on the power MOSFET. This time is generally about 250ns (typical) (see Minimum On-Time in the Electrical Characteristics table). In each switching cycle, the LT3958 keeps the power switch off for at least 200ns (typical) (see Minimum Off-Time in the Electrical Characteristics table). The minimum on-time, minimum off-time and the switching frequency define the minimum and maximum switching duty cycles a converter is able to generate: Minimum duty cycle = minimum on-time • frequency Maximum duty cycle = 1 – (minimum off-time • frequency) Programming the Output Voltage Table 1. Timing Resistor (RT ) Value SWITCHING FREQUENCY (kHz) RT (kΩ) 100 140 200 63.4 300 41.2 400 30.9 500 24.3 600 19.6 700 16.5 800 14 900 12.1 1000 10.5 The output voltage VOUT is set by a resistor divider, as shown in Figure 1. The positive and negative VOUT are set by the following equations: ⎛ R2 ⎞ VOUT,POSITIVE = 1.6V • ⎜ 1+ ⎟ ⎝ R1⎠ ⎛ R2 ⎞ VOUT,NEGATIVE = –0.8V • ⎜ 1+ ⎟ ⎝ R1⎠ The resistors R1 and R2 are typically chosen so that the error caused by the current flowing into the FBX pin during normal operation is less than 1% (this translates to a maximum value of R1 at about 158k). The operating frequency of the LT3958 can be synchronized to an external clock source. By providing a digital clock signal into the SYNC pin, the LT3958 will operate at the SYNC clock frequency. The LT3958 detects the rising edge of each Sync clock cycle. If this feature is used, an RT resistor should be chosen to program a switching frequency 20% slower than SYNC pulse frequency. Tie the SYNC pin to SGND if this feature is not used. It is recommended that the Sync input clock has a minimum pulse width of 200ns. 3958f 11 LT3958 APPLICATIONS INFORMATION Soft-Start FBX Frequency Foldback The LT3958 contains several features to limit peak switch currents and output voltage (VOUT) overshoot during start-up or recovery from a fault condition. The primary purpose of these features is to prevent damage to external components or the load. When VOUT is very low during start-up, or an output shortcircuit on a SEPIC, an inverting, or a flyback converter, the switching regulator must operate at low duty cycles to maintain the power switch current within the current limit range, since the inductor current decay rate is very low during switch off time. The minimum on-time limitation may prevent the switcher from attaining a sufficiently low duty cycle at the programmed switching frequency. So, the switch current may keep increasing through each switch cycle, exceeding the programmed current limit. To prevent the switch peak currents from exceeding the programmed value, the LT3958 contains a frequency foldback function to reduce the switching frequency when the FBX voltage is low (see the Normalized Switching Frequency vs FBX graph in the Typical Performance Characteristics section). High peak switch currents during start-up may occur in switching regulators. Since VOUT is far from its final value, the feedback loop is saturated and the regulator tries to charge the output capacitor as quickly as possible, resulting in large peak currents. A large surge current may cause inductor saturation or power switch failure. The LT3958 addresses this mechanism with the SS pin. As shown in Figure 1, the SS pin reduces the power MOSFET current by pulling down the VC pin through Q2. In this way the SS allows the output capacitor to charge gradually toward its final value while limiting the start-up peak currents. The typical start-up waveforms are shown in the Typical Performance Characteristics section. The inductor current IL slewing rate is limited by the soft-start function. Besides start-up (with EN/UVLO), soft-start can also be triggered by the following faults: 1. INTVCC > 12.8V (typical) 2. INTVCC < 3.55V 3. Thermal lockout Any of these three faults will cause the LT3958 to stop switching immediately. The SS pin will be discharged by Q3. When all faults are cleared and the SS pin has been discharged below 0.2V, a 10μA current source IS2 starts charging the SS pin, initiating a soft-start operation. The soft-start interval is set by the soft-start capacitor selection according to the equation: TSS = CSS • 1.25V 10µA During frequency foldback, external clock synchronization is disabled to prevent interference with frequency reducing operation. Loop Compensation Loop compensation determines the stability and transient performance. The LT3958 uses current mode control to regulate the output which simplifies loop compensation. The optimum values depend on the converter topology, the component values and the operating conditions (including the input voltage, load current, etc.). To compensate the feedback loop of the LT3958, a series resistor-capacitor network is usually connected from the VC pin to SGND. Figure 1 shows the typical VC compensation network. For most applications, the capacitor should be in the range of 470pF to 22nF, and the resistor should be in the range of 5k to 50k. A small capacitor is often connected in parallel with the RC compensation network to attenuate the VC voltage ripple induced from the output voltage ripple through the internal error amplifier. The parallel capacitor usually ranges in value from 10pF to 100pF. A practical approach to design the compensation network is to start with one of the circuits in this data sheet that is similar to your application, and tune the compensation network to optimize the performance. Stability should then be checked across all operating conditions, including load current, input voltage and temperature. Application Note 76 is a good reference. 3958f 12 LT3958 APPLICATIONS INFORMATION The Internal Power Switch Current On-Chip Power Dissipation and Thermal Lockout (TLO) For control and protection, the LT3958 measures the internal power MOSFET current by using a sense resistor (RSENSE) between GND and the MOSFET source. Figure 3 shows a typical waveform of the internal switch current (ISW). The on-chip power dissipation of LT3958 can be estimated using the following equation: ISW $ISW ISW(PEAK) t DTS TS 3958 F03 Figure 3. The Switch Current During a Switching Cycle Due to the current limit (minimum 3.3A) of the internal power switch, the LT3958 should be used in the applications that the switch peak current ISW(PEAK) during steady state normal operation is lower than 3.3A by a sufficient margin (10% or higher is recommended). The LT3958 switching controller incorporates 100ns timing interval to blank the ringing on the current sense signal across RSENSE immediately after M1 is turned on. This ringing is caused by the parasitic inductance and capacitance of the PCB trace, the sense resistor, the diode, and the MOSFET. The 100ns timing interval is adequate for most of the LT3958 applications. In the applications that have very large and long ringing on the current sense signal, a small RC filter can be added to filter out the excess ringing. Figure 4 shows the RC filter on the SENSE1 and SENSE2 pins. It is usually sufficient to choose 22Ω for RFLT and 2.2nF to 10nF for CFLT. Keep RFLT’s resistance low. Remember that there is 65μA (typical) flowing out of the SENSE2 pin. Adding RFLT will affect the internal power switch current limit threshold: PIC ≈ I2SW • D • RDS(ON) + V2SW(PEAK) • ISW • ƒ • 200pF/A + VIN • (1.6mA + ƒ • 10nC) where RDS(ON) is the internal switch on-resistance which can be obtained from the Typical Performance Characteristics section. VSW(PEAK) is the peak switch off-state voltage. The maximum power dissipation PIC(MAX) can be obtained by comparing PIC across all the VIN range at the maximum output current . The highest junction temperature can be estimated using the following equation: TJ(MAX) ≈ TA + PIC(MAX) • 42°C/W It is recommended to measure the IC temperature in steady state to verify that the junction temperature limit is not exceeded. A low switching frequency may be required to ensure TJ(MAX) does not exceed 125°C. If LT3958 die temperature reaches thermal lockout threshold at 165°C (typical), the IC will initiate several protective actions. The power switch will be turned off. A soft-start operation will be triggered. The IC will be enabled again when the junction temperature has dropped by 5°C (nominal). LT3958 SENSE1 RFLT SENSE2 CFLT SGND 3958 F04 Figure 4. The RC Filter on SENSE1 Pin and SENSE2 Pin ⎛ 65µA • RFLT ⎞ ISW _ILIM = ⎜ 1− ⎟ • 3.3A ⎝ 48mV ⎠ 3958f 13 LT3958 APPLICATIONS INFORMATION APPLICATION CIRCUITS The LT3958 can be configured as different topologies. The first topology to be analyzed will be the boost converter, followed by the flyback, SEPIC and inverting converters. mum output current (IO(MAX)) is less than the maximum output current capability by a sufficient margin (10% or higher is recommended): I O(MAX) ≤ Boost Converter: Switch Duty Cycle and Frequency The LT3958 can be configured as a boost converter for the applications where the converter output voltage is higher than the input voltage. Remember that boost converters are not short-circuit protected. Under a shorted output condition, the inductor current is limited only by the input supply capability. For applications requiring a step-up converter that is short-circuit protected, please refer to the Applications Information section covering SEPIC converters. The conversion ratio as a function of duty cycle is VOUT 1 = VIN 1− D in continuous conduction mode (CCM). For a boost converter operating in CCM, the duty cycle of the main switch can be calculated based on the output voltage (VOUT) and the input voltage (VIN). The maximum duty cycle (DMAX) occurs when the converter has the minimum input voltage: DMAX = VOUT − VIN(MIN) VOUT Discontinuous conduction mode (DCM) provides higher conversion ratios at a given frequency at the cost of reduced efficiencies and higher switching currents. Boost Converter: Maximum Output Current Capability and Inductor Selection For the boost topology, the maximum average inductor current is: I L(MAX) = IO(MAX) • 1 1− DMAX Due to the current limit of its internal power switch, the LT3958 should be used in a boost converter whose maxi- VIN(MIN) VOUT • ( 3.3A − 0.5 • ΔISW ) The inductor ripple current ΔISW has a direct effect on the choice of the inductor value and the converter’s maximum output current capability. Choosing smaller values of ΔISW increases output current capability, but requires large inductances and reduces the current loop gain (the converter will approach voltage mode). Accepting larger values of ΔISW provides fast transient response and allows the use of low inductances, but results in higher input current ripple and greater core losses, and reduces output current capability. It is recommended to choose a ΔISW lower than 0.6A. Given an operating input voltage range, and having chosen the operating frequency and ripple current in the inductor, the inductor value of the boost converter can be determined using the following equation: L= VIN(MIN) ΔISW • ƒ • DMAX The peak inductor current is the switch current limit (typical 4A), and the RMS inductor current is approximately equal to IL(MAX). The user should choose the inductors having sufficient saturation and RMS current ratings. Boost Converter: Output Diode Selection To maximize efficiency, a fast switching diode with low forward drop and low reverse leakage is desirable. The peak reverse voltage that the diode must withstand is equal to the regulator output voltage plus any additional ringing across its anode-to-cathode during the on-time. The average forward current in normal operation is equal to the output current. It is recommended that the peak repetitive reverse voltage rating VRRM is higher than VOUT by a safety margin (a 10V safety margin is usually sufficient). 3958f 14 LT3958 APPLICATIONS INFORMATION The power dissipated by the diode is: tON tOFF $VCOUT PD = IO(MAX) • VD where VD is diode’s forward voltage drop, and the diode junction temperature is: TJ = TA + PD • RθJA The RθJA to be used in this equation normally includes the RθJC for the device plus the thermal resistance from the board to the ambient temperature in the enclosure. TJ must not exceed the diode maximum junction temperature rating. Boost Converter: Output Capacitor Selection Contributions of ESR (equivalent series resistance), ESL (equivalent series inductance) and the bulk capacitance must be considered when choosing the correct output capacitors for a given output ripple voltage. The effect of these three parameters (ESR, ESL and bulk C) on the output voltage ripple waveform for a typical boost converter is illustrated in Figure 5. The choice of component(s) begins with the maximum acceptable ripple voltage (expressed as a percentage of the output voltage), and how this ripple should be divided between the ESR step ΔVESR and the charging/discharging ΔVCOUT. For the purpose of simplicity, we will choose 2% for the maximum output ripple, to be divided equally between ΔVESR and ΔVCOUT. This percentage ripple will change, depending on the requirements of the application, and the following equations can easily be modified. For a 1% contribution to the total ripple voltage, the ESR of the output capacitor can be determined using the following equation: ESRCOUT ≤ 0.01• VOUT ID(PEAK) For the bulk C component, which also contributes 1% to the total ripple: COUT ≥ VOUT (AC) $VESR RINGING DUE TO TOTAL INDUCTANCE (BOARD + CAP) 3958 F05 Figure 5. The Output Ripple Waveform of a Boost Converter The output capacitor in a boost regulator experiences high RMS ripple currents, as shown in Figure 5. The RMS ripple current rating of the output capacitor can be determined using the following equation: IRMS(COUT) ≥IO(MAX) • DMAX 1− DMAX Multiple capacitors are often paralleled to meet ESR requirements. Typically, once the ESR requirement is satisfied, the capacitance is adequate for filtering and has the required RMS current rating. Additional ceramic capacitors in parallel are commonly used to reduce the effect of parasitic inductance in the output capacitor, which reduces high frequency switching noise on the converter output. Boost Converter: Input Capacitor Selection The input capacitor of a boost converter is less critical than the output capacitor, due to the fact that the inductor is in series with the input, and the input current waveform is continuous. The input voltage source impedance determines the size of the input capacitor, which is typically in the range of 1μF to 100μF. A low ESR capacitor is recommended, although it is not as critical as for the output capacitor. The RMS input capacitor ripple current for a boost converter is: IRMS(CIN) = 0.3 • ΔIL IO(MAX) 0.01• VOUT • ƒ 3958f 15 LT3958 APPLICATIONS INFORMATION FLYBACK CONVERTER APPLICATIONS The LT3958 can be configured as a flyback converter for the applications where the converters have multiple outputs, high output voltages or isolated outputs. Figure 6 shows a simplified flyback converter. The flyback converter has a very low parts count for multiple outputs, and with prudent selection of turns ratio, can have high output/input voltage conversion ratios with a desirable duty cycle. However, it has low efficiency due to the high peak currents, high peak voltages and consequent power loss. The flyback converter is commonly used for an output power of less than 50W. The flyback converter can be designed to operate either in continuous or discontinuous mode. Compared to continuous mode, discontinuous mode has the advantage of smaller transformer inductances and easy loop compensation, and the disadvantage of higher peak-to-average current and lower efficiency. D NP:NS – + CIN VSN + CSN The flyback converter conversion ratio in the discontinuous mode operation is: VOUT NS D = • VIN NP D2 According to Figure 6, the peak SW voltage is: VSW(PEAK) = VIN(MAX) + VSN where VSN is the snubber capacitor voltage. A smaller VSN results in a larger snubber loss. A reasonable VSN is 1.5 to 2 times of the reflected output voltage: VSN = k • VOUT • NP NS k = 1.5 ~ 2 SUGGESTED RCD SNUBBER VIN period TS, three subintervals occur: DTS, D2TS, D3TS. During DTS, M is on, and D is reverse-biased. During D2TS, M is off, and LS is conducting current. Both LP and LS currents are zero during D3TS. RSN ID LP LS + + VOUT COUT – DSN According to the Absolute Maximum Ratings table, the SW voltage Absolute Maximum value is 84V. Therefore, the maximum primary to secondary turns ratio (for both the continuous and the discontinuous operation) should be. NP 84V − VIN(MAX) ≤ NS k • VOUT ISW SW LT3958 GND VSW 3958 F06 Figure 6. A Simplified Flyback Converter ISW Flyback Converter: Switch Duty Cycle and Turns Ratio The flyback converter conversion ratio in the continuous mode operation is: VOUT NS D = • VIN NP 1− D where NS/NP is the second to primary turns ratio. D is duty cycle. Figure 7 shows the waveforms of the flyback converter in discontinuous mode operation. During each switching ID ID(MAX) DTS D2TS TS t D3TS 3958 F07 Figure 7. Waveforms of the Flyback Converter in Discontinuous Mode Operation 3958f 16 LT3958 APPLICATIONS INFORMATION According to the preceding equations, the user has relative freedom in selecting the switch duty cycle or turns ratio to suit a given application. The selections of the duty cycle and the turns ratio are somewhat iterative processes, due to the number of variables involved. The user can choose either a duty cycle or a turns ratio as the start point. The following trade-offs should be considered when selecting the switch duty cycle or turns ratio, to optimize the converter performance. A higher duty cycle affects the flyback converter in the following aspects: • Lower MOSFET RMS current ISW(RMS), but higher MOSFET VSW peak voltage • Lower diode peak reverse voltage, but higher diode RMS current ID(RMS) • Higher transformer turns ratio (NP/NS) It is recommended to choose a duty cycle between 20% and 80%. Flyback Converter: Maximum Output Current Capability and Transformer Design The maximum output current capability and transformer design for continuous conduction mode (CCM) is chosen as presented here. The maximum duty cycle (DMAX) occurs when the converter has the minimum VIN: ⎛N ⎞ VOUT • ⎜ P ⎟ ⎝ NS ⎠ DMAX = ⎛N ⎞ VOUT • ⎜ P ⎟ + VIN(MIN) ⎝ NS ⎠ Due to the current limit of its internal power switch, the LT3958 should be used in a flyback converter whose maximum output current (IO(MAX)) is less than the maximum output current capability by a sufficient margin (10% or higher is recommended): IO(MAX) ≤ VIN(MIN) VOUT • DMAX • ( 3.3A − 0.5 • ΔISW ) The transformer ripple current ΔISW has a direct effect on the design/choice of the transformer and the converter’s output current capability. Choosing smaller values of ΔISW increases the output current capability, but requires large primary and secondary inductances and reduce the current loop gain (the converter will approach voltage mode). Accepting larger values of ΔISW allows the use of low primary and secondary inductances, but results in higher input current ripple, greater core losses, and reduces the output current capability. It is recommended to choose a ΔISW higher than 0.6A. Given an operating input voltage range, and having chosen the operating frequency and ripple current in the primary winding, the primary winding inductance can be calculated using the following equation: L= VIN(MIN) ΔISW • ƒ • DMAX The primary winding peak current is the switch current limit (typical 4A). The primary and secondary maximum RMS currents are: ILP(RMS) ≈ ILS(RMS) ≈ POUT(MAX) DMAX • VIN(MIN) • η I OUT(MAX) 1− DMAX where η is the converter efficiency. Based on the preceding equations, the user should design/choose the transformer having sufficient saturation and RMS current ratings. Flyback Converter: Snubber Design Transformer leakage inductance (on either the primary or secondary) causes a voltage spike to occur after the MOSFET turn-off. This is increasingly prominent at higher load currents, where more stored energy must be dissipated. In some cases a snubber circuit will be required to avoid overvoltage breakdown at the MOSFET’s drain node. There are different snubber circuits (such as RC snubber, RCD snubber, etc.) and Application Note 19 is a good reference on snubber design. An RCD snubber is shown in Figure 6. 3958f 17 LT3958 APPLICATIONS INFORMATION The snubber resistor value (RSN) can be calculated by the following equation: RSN = 2 • N V 2 SN − VSN • VOUT • P NS I2 SW(PEAK) • L LK • ƒ LLK is the leakage inductance of the primary winding, which is usually specified in the transformer characteristics. LLK can be obtained by measuring the primary inductance with the secondary windings shorted. The snubber capacitor value (CSN) can be determined using the following equation: VSN CSN = ΔVSN • RSN • ƒ where ΔVSN is the voltage ripple across CSN. A reasonable ΔVSN is 5% to 10% of VSN. The reverse voltage rating of DSN should be higher than the sum of VSN and VIN(MAX). Flyback Converter: Output Diode Selection The output diode in a flyback converter is subject to large RMS current and peak reverse voltage stresses. A fast switching diode with a low forward drop and a low reverse leakage is desired. Schottky diodes are recommended if the output voltage is below 100V. Approximate the required peak repetitive reverse voltage rating VRRM using: VRRM > NS •V +V NP IN(MAX) OUT The power dissipated by the diode is: PD = IO(MAX) • VD and the diode junction temperature is: TJ = TA + PD • RθJA The RθJA to be used in this equation normally includes the RθJC for the device, plus the thermal resistance from the board to the ambient temperature in the enclosure. TJ must not exceed the diode maximum junction temperature rating. Flyback Converter: Output Capacitor Selection The output capacitor of the flyback converter has a similar operation condition as that of the boost converter. Refer to the Boost Converter: Output Capacitor Selection section for the calculation of COUT and ESRCOUT. The RMS ripple current rating of the output capacitors in continuous operation can be determined using the following equation: DMAX 1− DMAX IRMS(COUT),CONTINUOUS ≈ IO(MAX) • Flyback Converter: Input Capacitor Selection The input capacitor in a flyback converter is subject to a large RMS current due to the discontinuous primary current. To prevent large voltage transients, use a low ESR input capacitor sized for the maximum RMS current. The RMS ripple current rating of the input capacitors in continuous operation can be determined using the following equation: IRMS(CIN),CONTINUOUS ≈ POUT(MAX) VIN(MIN) • η • 1− DMAX DMAX SEPIC CONVERTER APPLICATIONS The LT3958 can be configured as a SEPIC (single-ended primary inductance converter), as shown in Figure 1. This topology allows for the input to be higher, equal, or lower than the desired output voltage. The conversion ratio as a function of duty cycle is: VOUT + VD D = VIN 1− D in continuous conduction mode (CCM). In a SEPIC converter, no DC path exists between the input and output. This is an advantage over the boost converter for applications requiring the output to be disconnected from the input source when the circuit is in shutdown. 3958f 18 LT3958 APPLICATIONS INFORMATION Compared to the flyback converter, the SEPIC converter has the advantage that both the power MOSFET and the output diode voltages are clamped by the capacitors (CIN, CDC and COUT), therefore, there is less voltage ringing across the power MOSFET and the output diodes. The SEPIC converter requires much smaller input capacitors than those of the flyback converter. This is due to the fact that, in the SEPIC converter, the current through inductor L1 (which is series with the input) is continuous. SEPIC Converter: Switch Duty Cycle and Frequency For a SEPIC converter operating in CCM, the duty cycle of the main switch can be calculated based on the output voltage (VOUT), the input voltage (VIN) and the diode forward voltage (VD). The maximum duty cycle (DMAX) occurs when the converter has the minimum input voltage: DMAX = VOUT + VD VIN(MIN) + VOUT + VD SEPIC Converter: The Maximum Output Current Capability and Inductor Selection As shown in Figure 1, the SEPIC converter contains two inductors: L1 and L2. L1 and L2 can be independent, but can also be wound on the same core, since identical voltages are applied to L1 and L2 throughout the switching cycle. For the SEPIC topology, the current through L1 is the converter input current. Based on the fact that, ideally, the output power is equal to the input power, the maximum average inductor currents of L1 and L2 are: IL1(MAX) =IIN(MAX) =IO(MAX) • DMAX 1− DMAX In a SEPIC converter, the switch current is equal to IL1 + IL2 when the power switch is on, therefore, the maximum average switch current is defined as: ISW(MAX) =IL1(MAX) +IL2(MAX) =IO(MAX) • 1 1− DMAX Due to the current limit of its internal power switch, the LT3958 should be used in a SEPIC converter whose maximum output current (IO(MAX)) is less than the output current capability by a sufficient margin (10% or higher is recommended): IO(MAX) < (1 – DMAX) • (3.3A – 0.5 • ΔISW) The inductor ripple currents ΔIL1 and ΔIL2 are identical: ΔIL1 = ΔIL2 = 0.5 • ΔISW The inductor ripple current ΔISW has a direct effect on the choice of the inductor value and the converter’s maximum output current capability. Choosing smaller values of ΔISW requires large inductances and reduces the current loop gain (the converter will approach voltage mode). Accepting larger values of ΔISW allows the use of low inductances, but results in higher input current ripple and greater core losses and reduces output current capability. It is recommended to choose a ΔISW higher than 0.6A. Given an operating input voltage range, and having chosen the operating frequency and ripple current in the inductor, the inductor value (L1 and L2 are independent) of the SEPIC converter can be determined using the following equation: L1= L2 = VIN(MIN) 1.5A • ΔISW • ƒ • DMAX For most SEPIC applications, the equal inductor values will fall in the range of 1μH to 100μH. IL2(MAX) =IO(MAX) 3958f 19 LT3958 APPLICATIONS INFORMATION By making L1 = L2, and winding them on the same core, the value of inductance in the preceding equation is replaced by 2L, due to mutual inductance: L= VIN(MIN) ΔISW • ƒ • DMAX This maintains the same ripple current and energy storage in the inductors. The peak inductor currents are: IL1(PEAK) = IL1(MAX) + 0.5 • ΔIL1 IL2(PEAK) = IL2(MAX) + 0.5 • ΔIL2 The maximum RMS inductor currents are approximately equal to the maximum average inductor currents. Based on the preceding equations, the user should choose the inductors having sufficient saturation and RMS current ratings. SEPIC Converter: Output Diode Selection To maximize efficiency, a fast switching diode with a low forward drop and low reverse leakage is desirable. The average forward current in normal operation is equal to the output current. It is recommended that the peak repetitive reverse voltage rating VRRM is higher than VOUT + VIN(MAX) by a safety margin (a 10V safety margin is usually sufficient). The power dissipated by the diode is: PD = IO(MAX) • VD where VD is diode’s forward voltage drop, and the diode junction temperature is: TJ = TA + PD • RθJA The RθJA used in this equation normally includes the RθJC for the device, plus the thermal resistance from the board, to the ambient temperature in the enclosure. TJ must not exceed the diode maximum junction temperature rating. SEPIC Converter: Output and Input Capacitor Selection The selections of the output and input capacitors of the SEPIC converter are similar to those of the boost converter. Please refer to the Boost Converter: Output Capacitor Selection and Boost Converter: Input Capacitor Selection sections. SEPIC Converter: Selecting the DC Coupling Capacitor The DC voltage rating of the DC coupling capacitor (CDC, as shown in Figure 1) should be larger than the maximum input voltage: VCDC > VIN(MAX) CDC has nearly a rectangular current waveform. During the switch off-time, the current through CDC is IIN, while approximately –IO flows during the on-time. The RMS rating of the coupling capacitor is determined by the following equation: VOUT + VD VIN(MIN) IRMS(CDC) >IO(MAX) • A low ESR and ESL, X5R or X7R ceramic capacitor works well for CDC. INVERTING CONVERTER APPLICATIONS The LT3958 can be configured as a dual-inductor inverting topology, as shown in Figure 8. The VOUT to VIN ratio is: VOUT − VD D =− VIN 1− D in continuous conduction mode (CCM). CDC L1 VIN + L2 – + – CIN COUT SW LT3958 GND VOUT + D1 + 3758 F10 Figure 8. A Simplified Inverting Converter 3958f 20 LT3958 APPLICATIONS INFORMATION Inverting Converter: Switch Duty Cycle and Frequency Inverting Converter: Selecting the DC Coupling Capacitor For an inverting converter operating in CCM, the duty cycle of the main switch can be calculated based on the negative output voltage (VOUT) and the input voltage (VIN). The DC voltage rating of the DC coupling capacitor (CDC, as shown in Figure 10) should be larger than the maximum input voltage minus the output voltage (negative voltage): The maximum duty cycle (DMAX) occurs when the converter has the minimum input voltage: DMAX = VOUT − VD VOUT − VD − VIN(MIN) Inverting Converter: Output Diode and Input Capacitor Selections The selections of the inductor, output diode and input capacitor of an inverting converter are similar to those of the SEPIC converter. Please refer to the corresponding SEPIC converter sections. Inverting Converter: Output Capacitor Selection The inverting converter requires much smaller output capacitors than those of the boost, flyback and SEPIC converters for similar output ripples. This is due to the fact that, in the inverting converter, the inductor L2 is in series with the output, and the ripple current flowing through the output capacitors are continuous. The output ripple voltage is produced by the ripple current of L2 flowing through the ESR and bulk capacitance of the output capacitor: ⎛ ⎞ 1 ΔVOUT(P – P) = ΔIL2 • ⎜ ESRCOUT + 8 • ƒ • COUT ⎟⎠ ⎝ After specifying the maximum output ripple, the user can select the output capacitors according to the preceding equation. The ESR can be minimized by using high quality X5R or X7R dielectric ceramic capacitors. In many applications, ceramic capacitors are sufficient to limit the output voltage ripple. The RMS ripple current rating of the output capacitor needs to be greater than: IRMS(COUT) > 0.3 • ΔIL2 VCDC > VIN(MAX) – VOUT CDC has nearly a rectangular current waveform. During the switch off-time, the current through CDC is IIN, while approximately –IO flows during the on-time. The RMS rating of the coupling capacitor is determined by the following equation: IRMS(CDC) >IO(MAX) • DMAX 1− DMAX A low ESR and ESL, X5R or X7R ceramic capacitor works well for CDC. Board Layout The high power and high speed operation of the LT3958 demands careful attention to board layout and component placement. Careful attention must be paid to the internal power dissipation of the LT3958 at high input voltages, high switching frequencies, and high internal power switch currents to ensure that a junction temperature of 125°C is not exceeded. This is especially important when operating at high ambient temperatures. Exposed pads on the bottom of the package are SGND and SW terminals of the IC, and must be soldered to a SGND ground plane and a SW plane respectively. It is recommended that multiple vias in the printed circuit board be used to conduct heat away from the IC and into the copper planes with as much as area as possible. To prevent radiation and high frequency resonance problems, proper layout of the components connected to the IC is essential, especially the power paths with higher di/dt. The following high di/dt loops of different topologies should be kept as tight as possible to reduce inductive ringing: • In boost configuration, the high di/dt loop contains the output capacitor, the internal power MOSFET and the Schottky diode. 3958f 21 LT3958 APPLICATIONS INFORMATION • In flyback configuration, the high di/dt primary loop contains the input capacitor, the primary winding, the internal power MOSFET. The high di/dt secondary loop contains the output capacitor, the secondary winding and the output diode. • In SEPIC configuration, the high di/dt loop contains the internal power MOSFET, output capacitor, Schottky diode and the coupling capacitor. • In inverting configuration, the high di/dt loop contains internal power MOSFET, Schottky diode and the coupling capacitor. Check the stress on the internal power MOSFET by measuring the SW-to-GND voltage directly across the IC terminals. Make sure the inductive ringing does not exceed the maximum rating of the internal power MOSFET (84V). The small-signal components should be placed away from high frequency switching nodes. For optimum load regulation and true remote sensing, the top of the output voltage sensing resistor divider should connect independently to the top of the output capacitor (Kelvin connection), staying away from any high dV/dt traces. Place the divider resistors near the LT3958 in order to keep the high impedance FBX node short. Figure 9 shows the suggested layout of the 48V VOUT boost converter (see the Typical Applications section). R1 VIA TO VOUT R2 CSS RT RC CC 36 35 34 33 32 31 30 1 28 2 27 3 R3 37 4 25 24 6 CVCC LT3958 R4 23 8 21 38 9 20 10 12 13 14 15 16 17 L1 COUT COUT D1 CIN GND VOUT VIA TO VOUT VIN 3958 F09 VIAS TO SGND GROUND PLANE VIAS TO SW PLANE Figure 9. Suggested Layout of the 10V to 40V Input, 48V Output Boost Converter 3958f 22 LT3958 APPLICATIONS INFORMATION Recommended Component Manufacturers Some of the recommended component manufacturers are listed in Table 2. Table 2. Recommended Component Manufacturers VENDOR COMPONENTS WEB ADDRESS Capacitors avx.com Inductors, Transformers bhelectronics.com Coilcraft Inductors coilcraft.com Cooper Bussmann AVX BH Electronics Inductors bussmann.com Diodes, Inc Diodes diodes.com General Semiconductor Diodes generalsemiconductor. com International Rectifier Diodes irf.com Kemet Tantalum Capacitors kemet.com Toroid Cores mag-inc.com Microsemi Diodes microsemi.com Murata-Erie Inductors, Capacitors murata.co.jp Capacitors nichicon.com Magnetics Inc Nichicon On Semiconductor Diodes onsemi.com Panasonic Capacitors panasonic.com Pulse Inductors pulseeng.com Sanyo Capacitors sanyo.co.jp Sumida Inductors sumida.com Taiyo Yuden Capacitors t-yuden.com Capacitors, Inductors component.tdk.com Thermalloy Heat Sinks aavidthermalloy.com Tokin Capacitors nec-tokinamerica.com Toko Inductors tokoam.com United Chemi-Con Capacitors chemi-com.com TDK Vishay Inductors vishay.com Würth Elektronik Inductors we-online.com Capacitors vishay.com Small-Signal Discretes zetex.com Vishay/Sprague Zetex 3958f 23 LT3958 TYPICAL APPLICATIONS 10V to 40V Input, 48V Output Boost Converter L1 33μH CIN 4.7μF 50V X5R R3 392k VIN D1 GND EN/UVLO R4 53.6k COUT 4.7μF 50V X5R s2 SW Efficiency vs Output Current VOUT 48V 0.5A 100 LT3958 SGND SENSE1 SYNC SENSE2 R2 464k FBX RT SS RT 41.2k 300kHz CSS 0.33μF R1 15.8k INTVCC VC RC 10k CC 10nF VIN = 24V 95 EFFICIENCY (%) VIN 12V TO 40V 90 85 80 75 CVCC 4.7μF 10V X5R 70 0 400 100 200 300 OUTPUT CURRENT (mA) 500 3958 TA02b 3958 TA02a CIN, COUT : MURATA GRM32ER71H475KA88L D1: VISHAY SILICONIX 10BQ060 L2: VISHAY SILICONIX IHLP-4040DZ-11 High Voltage Flyback Power Supply DANGER! HIGH VOLTAGE OPERATION BY HIGH VOLTAGE TRAINED PERSONNEL ONLY VIN 5.5V TO 12V T1 1:10 47μF 16V s2 D1 VOUT 300V COUT 10mA 68nF s2 • • 22Ω 31.6k 220pF 1.5M GND VIN SW EN/UVLO 10k 1.5M LT3958 FBX SENSE1 SGND 22Ω SYNC SENSE2 RT 140k 100kHz SS VC 0.1μF 100pF INTVCC 10k 10nF 4.7μF 10V X5R 16.2k 10nF 3958 TA03 CIN : MURATA GRM32ER61C476M COUT : TDK C3225X7R2J683K D1: VISHAY SILICONIX GSD2004S DUAL DIODE CONNECTED IN SERIES T1: TDK DCT15EFD-U44S003 3958f 24 LT3958 TYPICAL APPLICATIONS 10V to 60V Input, 12V Output SEPIC Converter CDC 2.2μF, 100V X7R, s2 D1 VOUT 12V COUT 1A 22μF 16V X5R s2 • L1A VIN 10V TO 60V CIN 2.2μF 100V X5R VIN 392k L1B SW GND EN/UVLO 66.5k • LT3958 SGND SENSE1 SYNC SENSE2 105k FBX RT 41.2k 300kHz INTVCC VC SS 0.47μF 10k 10nF 15.8k CVCC 4.7μF 10V X5R 3958 TA04a CIN, CDC: MURATA GRM32ER72A225KA35L COUT: MURATA GRM32ER61C226KE20 D1: VISHAY SILICONIX 10MQ100N L1A, L1B: COILTRONICS DRQ125-220 Efficiency vs Output Current 90 Load Step Waveforms VIN = 24V VIN = 24V 85 VOUT 0.5V/DIV (AC) EFFICIENCY (%) 80 75 70 IOUT 0.8A 0.5A/DIV 0.2A 65 60 55 500μs/DIV 3958 TA04c 50 0 800 200 400 600 OUTPUT CURRENT (mA) 1000 3958 TA04b Frequency Foldback Waveforms When Output Short-Circuit Start-Up Waveforms VIN = 24V VIN = 24V VOUT 10V/DIV VOUT 5V/DIV VSW 20V/DIV IL1A + IL1B 2A/DIV IL1A + IL1B 2A/DIV 5ms/DIV 3958 TA04d 50μs/DIV 3958 TA04e 3958f 25 LT3958 TYPICAL APPLICATIONS 10V to 60V Input, –12V Output Inverting Converter CDC 2.2μF, 100V X7R, s2 • L1B CIN 2.2μF 100V X5R VIN 392k D1 SW GND EN/UVLO 66.5k VOUT –12V COUT 1A 22μF 16V X5R s2 • L1A VIN 10V TO 60V LT3958 SGND SENSE1 SYNC SENSE2 105k FBX RT 41.2k 300kHz SS INTVCC VC 0.47μF 10k 10nF 7.5k CVCC 4.7μF 10V X5R 3958 TA05a CIN, CDC: MURATA GRM32ER72A225KA35L COUT: MURATA GRM32ER61C226KE20 D1: VISHAY SILICONIX 10MQ100N L1A, L1B: COILTRONICS DRQ125-220 Efficiency vs Output Current 90 Load Step Waveforms VIN = 24V VIN = 24V 85 EFFICIENCY (%) 80 VOUT 1V/DIV (AC) 75 70 IOUT 0.8A 0.5A/DIV 0.2A 65 60 55 500μs/DIV 3958 TA05c 50 0 800 200 400 600 OUTPUT CURRENT (mA) 1000 3958 TA05b Frequency Foldback Waveforms When Output Short-Circuit Start-Up Waveforms VIN = 24V VIN = 24V VOUT 5V/DIV VOUT 10V/DIV VSW 20V/DIV IL1A + IL1B 2A/DIV IL1A + IL1B 2A/DIV 5ms/DIV 3958 TA05d 50μs/DIV 3958 TA05e 3958f 26 LT3958 PACKAGE DESCRIPTION UHE Package Variation: UHE28MA 36-Lead Plastic QFN (5mm × 6mm) (Reference LTC DWG # 05-08-1836 Rev B) 28 27 25 24 23 21 20 0.70 p0.05 30 31 5.50 p 0.05 4.10 p 0.05 1.50 REF 16 3.00 p 0.05 3.00 p 0.05 32 33 17 1.53 p 0.05 1.88 p 0.05 0.12 p 0.05 15 14 PACKAGE OUTLINE 13 0.48 p 0.05 34 12 35 36 1 2 3 4 6 0.50 BSC 8 9 0.25 p0.05 10 2.00 REF 5.10 p 0.05 6.50 p 0.05 RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED 5.00 p 0.10 0.75 p 0.05 R = 0.10 TYP PIN 1 TOP MARK (NOTE 6) 30 31 32 1.50 REF 33 34 35 28 27 2.00 REF 25 24 6.00 p 0.10 1 1.88 p 0.10 3.00 p 0.10 0.12 p 0.10 20 2 3 4 6 23 21 36 PIN 1 NOTCH R = 0.30 OR 0.35 s 45o CHAMFER 1.53 p 0.10 0.48 p 0.10 3.00 p 0.10 8 R = 0.125 TYP 9 10 0.40 p 0.10 0.200 REF 0.00 – 0.05 17 16 15 0.25 p 0.05 0.50 BSC 14 13 12 (UHE28MA) QFN 0409 REV B BOTTOM VIEW—EXPOSED PAD NOTE: 1. DRAWING IS NOT A JEDEC PACKAGE OUTLINE 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.20mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 3958f 27 LT3958 TYPICAL APPLICATIONS 5V Output Nonisolated Flyback Power Supply T1 3:1 VIN 10V TO 40V 0.1μF 50V CIN 4.7μF 50V X5R D1 • 1.8k 1W Efficiency vs Output Current VOUT 5V 2A 90 COUT 100μF 6.3V • 80 EFFICIENCY (%) DSN 200k SW GND VIN EN/UVLO 32.4k LT3958 SENSE1 SYNC SENSE2 34k 1% 63.4k 200kHz 10k 65 50 INTVCC 0.47μF 70 55 FBX VC 75 60 SGND RT SS VIN = 24V 85 0 15.8k 1% 4.7μF 10V X5R 0.5 1 1.5 OUTPUT CURRENT (A) 2 3958 TA05b 100pF 10nF 3958 TA06a T1: COILTRONICS VP2-0066 RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LT3580 Boost/Inverting DC/DC Converter with 2A Switch, Soft-Start and Synchronization 2.5V ≤ VIN ≤ 32V, Current Mode Control, 200kHz to 2.5MHz, 3mm × 3mm DFN-8, MSOP-8E LT3573 Isolated Flyback Switching Regulator with 60V Integrated Switch 3V ≤ VIN ≤ 40V, Up to 7W, No Opto-Isolator or Third Winding Required, MSOP-16E LT3574 Isolated Flyback Switching Regulator with 60V Integrated Switch 3V ≤ VIN ≤ 40V, Up to 3W, No Opto-Isolator or Third Winding Required, MSOP-16E LT3757 Boost, Flyback, SEPIC and Inverting Controller 2.9V ≤ VIN ≤ 40V, Current Mode Control, 100kHz to 1MHz Programmable Operation Frequency, 3mm × 3mm DFN-10 and MSOP-10E Package LT3758 Boost, Flyback, SEPIC and Inverting Controller 5.5V ≤ VIN ≤ 100V, Current Mode Control, 100kHz to 1MHz Programmable Operation Frequency, 3mm × 3mm DFN-10 and MSOP-10E Package LTC1871/LTC1871-1/ Wide Input Range, No RSENSE™ Low Quiescent LTC1871-7 Current Flyback, Boost and SEPIC Controller Adjustable Switching Frequency, 2.5V ≤ VIN ≤ 36V, Burst Mode Operation at Light Load LT3825 Isolated No-Opto Synchronous Flyback Controller VIN 16V to 75V Limited by External Components, Up to 60W, Current Mode Control LT3837 Isolated No-Opto Synchronous Flyback Controller VIN 4.5V to 36V Limited by External Components, Up to 60W, Current Mode Control LT1725 Isolated No-Opto Flyback Controller VIN 16V to 75V Limited by External Components, Current Mode Control LT1737 Isolated No-Opto Flyback Controller VIN 4.5V to 36V Limited by External Components, Current Mode Control LTC3803/LTC3803-5 200kHz Flyback DC/DC Controller VIN and VOUT Limited Only by External Components, ThinSOT™ Package LTC3805/LTC3805-5 Adjustable Fixed 70kHz to 700kHz Operating Frequency Flyback Controller VIN and VOUT Limited Only by External Components, 3mm × 3mm DFN-10, MSOP-10E LT1619 Boost, SEPIC and Flyback Current Mode PWM Controller 1.9V ≤ VIN ≤ 18V, 300kHz Fixed Operating Frequency LT3574 Isolated Flyback Switching Regulator with 60V Integrated Switch 3V ≤ VIN ≤ 40V, Up to 3W, No Opto-Isolator or Third Winding Required, MSOP-16 Package 3958f 28 Linear Technology Corporation LT 0510 • PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com © LINEAR TECHNOLOGY CORPORATION 2010