LT5524 Low Distortion IF Amplifier/ADC Driver with Digitally Controlled Gain U FEATURES DESCRIPTIO ■ The LT®5524 is a programmable gain amplifier (PGA) with bandwidth extending from low frequency (LF) to 540MHz. It consists of a digitally controlled variable attenuator, followed by a high linearity amplifier. Four parallel digital inputs control the gain over a 22.5dB range with 1.5dB step resolution. An on-chip power supply regulator/filter helps isolate the amplifier signal path from external noise sources. ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Output IP3 at 100MHz: 40dBm Maximum Output Power: 16dBm Bandwidth: LF to 540MHz Propagation Delay: 0.8ns Maximum Gain: 27dB Gain Control Range: 22.5dB Gain Control Step: 1.5dB Gain Control Settling Time: 500ns Noise Figure: 8.6dB at 100MHz (Max Gain) Output Noise Floor: –138dBm/Hz (Max Gain) Reverse Isolation: –92dB Single Supply: 4.75V to 5.25V Shutdown Mode Enable/Disable Time: 1µs Differential I/O Interface 20-Lead TSSOP Package The LT5524’s open-loop architecture offers stable operation for any practical load conditions, including peakingfree AC response when driving capacitive loads, and excellent reverse isolation. The LT5524 may be operated broadband, where the output differential RC time constant sets the bandwidth, or it may be used as a narrowband driver with the appropriate output filter. U APPLICATIO S ■ ■ ■ ■ High Linearity ADC Driver IF Sampling Receivers VGA IF Power Amplifier 50Ω Driver Instrumentation Applications U ■ , LTC and LT are registered trademarks of Linear Technology Corporation. Patents Pending. TYPICAL APPLICATIO Output IP3 vs Frequency, ROUT = 200Ω 54 5V CHOKE RF INPUT IF BPF LO IF AMP 48 0.1µF 100Ω LT5524 0.1µF 0.1µF GAIN CONTROL ADC 5524 TA01 OIP3 (dBm) 0.1µF 51 CHOKE 45 MAX GAIN 42 39 1.5dB ATTENUATION STEP 36 4 LINES 33 30 0 50 100 150 200 FREQUENCY (MHz) 5524 TA02 5524f 1 LT5524 U W W W U U W ABSOLUTE MAXIMUM RATINGS PACKAGE/ORDER INFORMATION (Notes 1, 2) Power Supply Voltage (VCC1, VCC2) .......................... 6V Output DC Voltage (OUT+, OUT–) ............................. 7V Control Input Voltage (EN, PGAx) ............. –0.5V to VCC Signal Input Voltage (IN+, IN–) ................... –0.5V to 3V Operating Ambient Temperature Range .. – 40°C to 85°C Storage Temperature Range ................. – 65°C to 150°C Lead Temperature (Soldering, 10 sec).................. 300°C TOP VIEW EN 1 20 NC VCC1 2 19 VCC2 GND 3 18 GND GND 4 17 GND IN + 5 IN – 6 21 ORDER PART NUMBER LT5524EFE 16 OUT – 15 OUT + GND 7 14 GND GND 8 13 GND PGA0 9 12 PGA3 PGA1 10 11 PGA2 FE PACKAGE 20-LEAD PLASTIC TSSOP TJMAX = 150°C, θJA = 38°C/W EXPOSED PAD (PIN 21) IS GND MUST BE SOLDERED TO PCB Consult LTC Marketing for parts specified with wider operating temperature ranges. U U WW PROGRA ABLE GAI SETTI GS ATTENUATION STEP RELATIVE TO MAX GAIN 1 0dB 2 –1.5dB 3 –3.0dB 4 –4.5dB 5 –6.0dB 6 –7.5dB 7 –9.0dB 8 –10.5dB 9 –12.0dB 10 –13.5dB 11 –15.0dB 12 –16.5dB 13 –18.0dB 14 –19.5dB 15 –21.0dB 16 –22.5dB *ROUT = 200Ω PGA0 High Low High Low High Low High Low High Low High Low High Low High Low PGA1 High High Low Low High High Low Low High High Low Low High High Low Low PGA2 High High High High Low Low Low Low High High High High Low Low Low Low PGA3 High High High High High High High High Low Low Low Low Low Low Low Low POWER GAIN* 27.0dB 25.5dB 24.0dB 22.5dB 21.0dB 19.5dB 18.0dB 16.5dB 15.0dB 13.5dB 12.0dB 10.5dB 9.0dB 7.5dB 6.0dB 4.5dB (Note 3) 5524f 2 LT5524 DC ELECTRICAL CHARACTERISTICS VCC = 5V, VCCO = 5V, EN = 3V, TA = 25°C, unless otherwise noted. (Note 7) (Test circuits shown in Figures 9 and 10) SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS 4.75 5 5.25 V 3 5 5.5 V 1.15 1.3 Normal Operating Conditions VCC Supply Voltage (Pins 2, 19) (Note 4) VCCO OUT+, OUT– Output Pin DC Common Mode Voltage OUT+, OUT– Connected to VOSUP via Choke Inductors or Resistors (Note 5) Shutdown DC Characteristics, EN = 0.6V VIN(BIAS) IN+, IN– Bias Voltage Max Gain (Note 6) 1.5 V IIL(PGA) PGAO, PGA1, PGA2, PGA3 Input Current VIN = 0.6V 20 µA IIH(PGA) PGAO, PGA1, PGA2, PGA3 Input Current VIN = 5V 20 µA IOUT OUT+, OUT– Current All Gain Settings ICC VCC Supply Current All Gain Settings (Note 4) 44 20 µA 100 µA 0.6 V Enable and PGA Inputs DC Characteristics VIL EN and PGAx Input Low Voltage x = 0, 1, 2, 3 VIH EN and PGAx Input High Voltage x = 0, 1, 2, 3 IIL(PGA) PGAO, PGA1, PGA2, PGA3 Input Current VIN = 0.6V IIH(PGA) PGAO, PGA1, PGA2, PGA3 Input Current VIN = 3V and 5V IIL(EN) EN Input Current VIN = 0.6V IIH(EN) EN Input Current VIN = 3V VIN = 5V 3 V 20 µA 15 30 µA 4 20 µA 18 38 100 µA µA 1.48 1.65 V DC Characteristics, EN = 3V VIN(BIAS) IN+, IN– Bias Voltage RIN Input Differential Resistance All Gain Settings (DC) 122 Ω gm Amplifier Transconductance Max Gain 0.15 S IOUT OUT+, OUT– Quiescent Current All Gain Settings, VOUT = 5V Max Gain (Note 6) 1.34 17 20 24 mA IOUT(OFFSET) Output Current Mismatch All Gain Settings, IN+, IN– ICC VCC1 + VCC2 Supply Current Max Gain (Note 4) Min Gain (Note 4) 34 36 40 43 mA mA ICC(TOTAL) Total Supply Current ICC + 2 • IOUT (Max Gain) 75 91 mA Open 100 µA 5524f 3 LT5524 AC ELECTRICAL CHARACTERISTICS VCC = 5V, VCCO = 5V, EN = 3V, TA = 25°C, ROUT = 200Ω. Maximum gain specifications are with respect to differential inputs and differential outputs, unless otherwise noted. (Note 7) (Test circuits shown in Figures 9 and 10) SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS Dynamic Performance BW Large-Signal –3dB Bandwidth VOUT(CLIP) Output Voltage Clipping Levels All Gain Settings (Note 8), ROUT = 100Ω Each OUT+, OUT– with Respect to Ground LF to 540 2 MHz 8 V (Note 11) POUT(MAX) Clipping Limited Maximum Sinusoidal Output Power All Gain Settings, Single Tone, fIN = 100MHz (Note 10) 16 dBm gm Amplifier Transconductance Max Gain, fIN = 100MHz 0.15 S S12 Reverse Isolation fIN = 100MHz (Note 9) –92 dB Output Third Order Intercept Point for PGA0 = High (PGA1, PGA2, PGA3 Any State) POUT = 4dBm (Each Tone), 200kHz Tone Spacing, fIN = 100MHz +40 dBm Output Third Order Intercept Point for PGA0 = Low (PGA1, PGA2, PGA3 Any State) POUT = 4dBm (Each Tone), 200kHz Tone Spacing, fIN = 100MHz +36 dBm Distortion and Noise OIP3 HD2 Second Harmonic Distortion POUT = 5dBm (Single Tone), fIN = 50MHz –76 dBc HD3 Third Harmonic Distortion POUT = 5dBm (Single Tone), fIN = 50MHz –72 dBc NFLOOR Output Noise Floor (PGAO, PGA2, PGA3 Any State) PGA1 = High, fIN = 100MHz PGA1 = Low, fIN = 100MHz –138 –140 dBm/Hz dBm/Hz NF Noise Figure Max Gain Setting, fIN = 100MHz 8.6 dB PGA Settling Time Output Settles within 10% of Final Value 500 ns Enable/Disable Time Output Settles within 10% of Final Value 600 ns 27 dB Amplifier Power Gain and Gain Step GMAX Maximum Gain fIN = 20MHz and 200MHz GMIN Minimum Gain fIN = 20MHz and 200MHz GSTEP Gain Step Size fIN = 20MHz and 200MHz Gain Step Accuracy fIN = 20MHz and 200MHz 4.5 0.8 1.5 dB 2.2 dB ±0.2 dB Amplifier I/O Impedance (Parallel Values, Specified Differentially) RIN Input Resistance fIN = 100MHz 122 Ω CIN Input Capacitance fIN = 100MHz 2 pF RO Output Resistance fIN = 100MHz 5 kΩ CO Output Capacitance fIN = 100MHz 1.7 pF Note 1: Absolute Maximum Ratings are those values beyond which the life of the device may be impaired. Note 2: All voltage values are with respect to ground. Note 3: Default state for open PGA inputs. Note 4: VCC1 and VCC2 (Pins 2 and 19) are internally connected. Note 5: External VOSUP is adjusted such that VCCO output pin common mode voltage is as specified when resistors are used. For choke inductors or transformer, VOSUP = VCCO = 5V typ. Note 6: Internally generated common mode input bias voltage requires capacitive or transformer coupling to the signal source. Note 7: Specifications over the –40°C to 85°C operating temperature range are assured by design, characterization and correlation with statistical process controls. Gain always refers to power gain. Input matching is assumed. PIN is the available input power. POUT is the power into the external load, ROUT, as seen by the LT5524 differential outputs. All dBm figures are with respect to 50Ω. Note 8: High frequency operation is limited by the RC time constants at the input and output ports. The low frequency (LF) roll-off is set by I/O interface choice. Note 9: Limited by package and board isolation. Note 10: See “Clipping Free Operation” in the Applications Information section. Refer to Figure 7. Note 11: Although the instantaneous AC voltage on the OUT+ or OUT– pins may in some situations safely exceed 8V (with respect to ground), in no case should the DC voltage on these pins be allowed to exceed the ABSMAX tested limit of 7V. 5524f 4 LT5524 U W TYPICAL PERFOR A CE CHARACTERISTICS TA = 25°C, VCC = 5V, VCCO = 5V, EN = 3V, control input levels VIL = 0.6V, VIH = 3V unless otherwise noted. (Test circuit shown in Figure 9) Gain Error vs Attenuation Step at 25MHz, ROUT = 200Ω Frequency Response for All Gain Steps, ROUT = 200Ω 30 0.8 27 0.8 25°C –40°C 85°C 0.6 24 15 12 9 0.4 GAIN ERROR (dB) 18 25°C –40°C 85°C 0.6 0.4 21 GAIN ERROR (dB) POWER GAIN (dB) Gain Error vs Attenuation Step at 100MHz, ROUT = 200Ω 0.2 0 –0.2 0.2 0 –0.2 –0.4 –0.4 –0.6 –0.6 6 3 –0.8 0 100 FREQUENCY (MHz) 10 0 1000 3 12 15 6 9 18 ATTENUATION STEP (dB) 5524 G01 Maximum Gain vs VCC at 120MHz, ROUT = 200Ω 25 5.2 27.4 20 27.2 –40°C 85°C 27.0 25°C 26.8 4.4 26.6 4.2 26.4 4.9 5.1 4.7 4.9 5.1 5.5 5.3 VCC (V) –5 –31 –28 –25 –22 –19 –16 –13 –10 PIN (dBm) OIP3 vs Frequency at Pin = –23dBm, Max Gain and 1.5dB Attenuation Step, ROUT = 200Ω –7 5524 G06 5524 G05 5524 G04 Harmonic Distortion vs POUT at 50MHz, Max Gain, ROUT = 200Ω –40 54 –45 51 –50 –55 48 –60 HD(dBc) 45 MAX GAIN 42 39 –65 HD3 –70 HD2 –75 –80 1.5dB ATTENUATION STEP 36 –85 HD5 –90 33 30 ROUT = 200Ω 0 26.2 4.5 5.5 5.3 10 5 85°C VCC (V) OIP3 (dBm) 4.7 POUT (dBm) GAIN (dB) 25°C 21 15 –40°C 4.8 4.0 4.5 12 15 6 9 18 ATTENUATION STEP (dB) POUT vs PIN at 50MHz, Max Gain 27.6 4.6 3 5524 G03 5.4 5.0 0 5524 G02 Minimum Gain vs VCC at 120MHz, ROUT = 200Ω GAIN (dB) –0.8 21 HD4 –95 –100 0 50 100 150 200 FREQUENCY (MHz) 5524 G07 –6 –3 0 6 3 POUT (dBm) 9 12 15 5524 G08 5524f 5 LT5524 U W TYPICAL PERFOR A CE CHARACTERISTICS Two tones, 200kHz spacing, TA = 25°C, EN = 3V, VCC = 5V, VCCO = 5V, control input levels VIL = 0.6V, VIH = 3V unless otherwise noted. (Test circuit shown in Figure 10) NF vs Attenuation Step at Freq = 100MHz Noise Figure vs Frequency Output Noise Floor vs Attenuation Step, Freq = 100MHz, ROUT = 200Ω –136 30 10.0 27 9.5 8.5 15 9 3dB ATTENUATION STEP (PGA1 = LOW) 7.5 18 12 MAX GAIN 8.0 NOISE FLOOR (dBm/Hz) 21 NF (dB) NF (dB) 9.0 –137 24 1.5dB ATTENUATION STEP (PGA0 = LOW) 6 PGA1 = HIGH –138 –139 PGA1 = LOW –140 –141 3 7.0 0 50 0 100 150 200 250 300 350 400 FREQUENCY (MHz) –142 0 3 6 9 12 18 15 ATTENUATION STEP (dB) 5524 G09 21 0 3 6 9 12 15 18 ATTENUATION STEP (dB) 5524 G11 5524 G10 Pulse Response vs Output Level at Max Gain. Indicated Voltage Levels are into 50Ω External Load 21 Single-Ended Output Current vs Attenuation Step VIN(BIAS) vs Attenuation Step 21.0 1.60 20.5 1.55 CURRENT (mA) 2VP-P 1.5VP-P 1VP-P INPUTS 20.0 VIN(BIAS) (V) COUT = 0.82pF 85°C 1.50 –40°C 1.45 85°C 25°C 25°C 19.5 –40°C 19.0 2ns/DIV 5524 G12 1.40 0 6 9 12 15 18 ATTENUATION STEP (dB) 3 21 0 6 9 12 15 18 ATTENUATION STEP (dB) 3 5524 G14 5524 G13 ICC Shutdown Current vs VCC, EN = 0.6V Total ICC vs Attenuation Step 70 78 85°C 75 25°C 60 85°C 50 CURRENT (µA) CURRENT (mA) 80 73 –40°C 70 25°C 40 30 –40°C 20 68 65 21 10 0 3 6 9 12 15 18 ATTENUATION STEP (dB) 21 0 4.5 4.7 4.9 5.1 5.3 5.5 INPUT VCC (V) 5524 G15 5524 G16 5524f 6 LT5524 U U U PI FU CTIO S EN (Pin 1): Enable Pin for Amplifier. When the input voltage is higher than 3V, the amplifier is turned on. When the input voltage is less than or equal to 0.6V, the amplifier is turned off. This pin is internally pulled to ground if not connected. PGA2 (Pin 11): Amplifier PGA Control Input Pin for the 6dB Attenuation Step (see Programmable Gain table). Input is high when the input voltage is greater than 3V. Input is low when the input voltage is less than or equal to 0.6V. This pin is internally pulled to ground if not connected. VCC1 (Pin 2): Power Supply. This pin is internally connected to VCC2 (Pin 19). Decoupling capacitors (1000pF and 0.1µF for example) may be required in some applications. PGA3 (Pin 12): Amplifier PGA Control Input Pin for 12dB Attenuation Step (see Programmable Gain table). Input is high when the input voltage is greater than 3V. Input is low when the input voltage is less than or equal to 0.6V. This pin is internally pulled to ground if not connected. GND (Pins 3, 4, 7, 8, 13, 14, 17, 18): Ground. IN+ (Pin 5): Positive Signal Input Pin with Internal DC Bias. OUT+ (Pin 15): Positive Amplifier Output. A transformer with center tap tied to VCC or a choke inductor is recommended to source the DC quiescent current. IN– (Pin 6): Negative Signal Input Pin with Internal DC Bias. OUT– (Pin 16): Negative Amplifier Output. A transformer with center tap tied to VCC or a choke inductor is recommended to source the DC quiescent current. PGA0 (Pin 9): Amplifier PGA Control Input Pin for the 1.5dB Attenuation Step (see Programmable Gain table). Input is high when the input voltage is greater than 3V. Input is low when the input voltage is less than or equal to 0.6V. This pin is internally pulled to ground if not connected. VCC2 (Pin 19): Power Supply. This pin is internally connected to VCC1 (Pin 2). NC (Pin 20): Not Connected. PGA1 (Pin 10): Amplifier PGA Control Input Pin for the 3dB Attenuation Step (see Programmable Gain table). Input is high when the input voltage is greater than 3V. Input is low when the input voltage is less than or equal to 0.6V. This pin is internally pulled to ground if not connected. Exposed Pad (Pin 21): Ground. This pin must be soldered to the printed circuit board ground plane for good heat transfer. W BLOCK DIAGRA LT5524 5 6 IN+ ATTENUATOR IN– RIN 100Ω VOLTAGE REGULATOR AND BIAS GND (3, 4, 7, 8 13, 14, 17, 18) VCC1 2 VCC2 19 OUT – OUT+ GAIN CONTROL LOGIC PGA3 12 16 AMPLIFIER ENABLE CONTROL PGA2 PGA1 11 10 15 PGA0 9 NC 20 EN 1 21 5524 F01 Figure 1. Functional Block Diagram 5524f 7 LT5524 U W U U APPLICATIO S I FOR ATIO Circuit Operation The LT5524 is a high linearity amplifier with high impedance output (Figure 1). It consists of the following sections: • An input variable attenuator “gain-control” block with 122Ω input impedance • A differential transconductance amplifier, with enable input • An internal bias block with internal voltage regulator • A gain control logic block The LT5524 amplifier provides amplification with very low distortion using a linearized open-loop architecture. In contrast with high linearity amplifiers employing negative feedback, the LT5524 offers: where: gm is the LT5524 transconductance = 0.15S. RIN is the LT5524 differential input impedance ≅ 122Ω. Input impedance matching is assumed. ROUT is the external differential output impedance as seen by the LT5524’s differential outputs. ROUT should be distinguished from the actual load impedance, RLOAD, which will typically be coupled to the LT5524 output by an impedance transformation network. The power gain as a function of ROUT is plotted in Figure 2. The ideal relationship is linear. The curved line indicates the roll-off due to the finite (noninfinite) output resistance of the LT5524. 45 • Stable operation for any practical load 40 • A capacitive output reactance (not inductive) that provides peaking free AC response to capacitive loads 35 The LT5524 is a transconductance amplifier and its operation can be understood conceptually as consisting of two steps: First, the input signal voltage is converted to an output current. The intermodulation distortion (in dBc) of the LT5524 output current is determined by the input signal level, and is almost independent of the output load conditions. Thus, the LT5524’s input IP3 is also nearly independent of the output load. Next, the external output load (ROUT) converts the output current to output voltage (or power). The LT5524’s voltage and power gain both increase with increasing ROUT. Accordingly, the output power and output IP3 also increase with increasing ROUT. The actual output linearity performance in the application will thus be set by the choice of output load, as well as by the output network. Maximum Gain Calculation The maximum power gain (with the 0dB attenuation step) is: GAIN (dB) • Exceptional reverse isolation of –100dB at 50MHz and –78dB at 300MHz (package and board leakage limited) 30 25 20 15 10 IDEAL WITH RO 5 0 20 100 1000 2000 ROUT (Ω) 5524 F02 Figure 2. Power Gain as a Function of ROUT The actual available output power (as well as power gain and OIP3) will be reduced by losses in the output interface, consisting of: • The insertion loss of the output impedance transformation network (for example the transformer insertion loss in Figure 6) • About –3dB loss if a matching resistor (RMATCH in Figure 6) is used to provide output load impedance back-matching (for example when driving transmission lines) GPWR(dB) = 10 • log(gm2 • RIN • ROUT) 5524f 8 LT5524 U W U U APPLICATIO S I FOR ATIO VOSUP Input Interface C3 For the lowest noise and highest linearity, the LT5524 should be driven with a differential input signal. Singleended drive will severely degrade linearity and noise performance. • Match the source impedance to the LT5524, RIN ≅ 122Ω • Provide well balanced differential input drive (capacitor C2 in Figure 4) • Minimize insertion loss to avoid degrading the noise figure (NF) RLOAD 50Ω C2 RLOAD 50Ω ROUT + LT5524 F05 Figure 5. Output Impedance-Matched and Capacitively Coupled to a Differential Load Input matching network design criteria are: • DC block the LT5524 internal bias voltage (see Input Bias Voltage section for DC coupling information) R2 51Ω C1 – RIN 122Ω IN– Example input matching networks are shown in Figures 3 and 4. R1 51Ω LT5524 IN+ Note: In Figure 5, (choke) inductors may be placed in parallel with or used to replace resistors R1 and R2, thus eliminating the DC voltage drop across these resistors. VOSUP IN+ IN– LT5524 – RIN 122Ω C1 RMATCH 255Ω (OPTIONAL) ROUT + RLOAD 50Ω T2 4:1 • • • LT5524 F06 R1 50Ω C1 VSRC R2 50Ω C2 LT5524 IN+ Figure 6. Output Impedance-Matched and Transformer-Coupled to a Single-Ended Load – RIN 122Ω IN– + LT5524 F03 Figure 3. Input Capacitively-Coupled to a Differential Source RSRC 50Ω T1 1:2 • VSRC IN+ • • IN– C2 0.33µF • Provide DC isolation between the LT5524 DC output voltage and RLOAD. • Provide a path for the output DC current from the output voltage source VOSUP. LT5524 – RIN 122Ω + Output network design criteria are: LT5524 F04 Figure 4. Input Transformer-Coupled to a Single-Ended Source Output Interface The output interface network provides an impedance transformation between the actual load impedance, RLOAD, and the LT5524 output loading, ROUT, chosen to maximize power or linearity, or to minimize output noise, or for some other criteria as explained in the following sections. Two examples of output matching networks are shown in Figures 5 and 6 (as implemented in the LT5524 demo boards). • Provide an impedance transformation, if required, between the load impedance, RLOAD, and the optimum ROUT loading. • Set the bandwidth of the output network. • Optional: Provide board output impedance matching using resistor RMATCH (when driving a transmission line). • Use high linearity passive parts to avoid introducing noninearity. Note that there is a noise penalty of up to 6dB when using power delivered by only one output in Figure 5. 5524f 9 LT5524 U W U U APPLICATIO S I FOR ATIO Clipping Free Operation To avoid current clipping, the output signal current should not exceed the DC quiescent current, IOUT = 20mA (typical). Correspondingly, the maximum input voltage, VIN(MAX), is IOUT/gm = 133mV (peak). In power terms, PIN(MAX) = –11.5dBm (assuming RIN = 122Ω). To avoid output voltage clipping (due to LT5524 output stage saturation or breakdown), the single-ended output voltage swing should stay within the specified limits; i.e., 2V ≤ VOUT ≤ 8V. For a DC output bias of 5V, the maximum single ended swing will be 3Vpeak and the maximum differential swing will be 6Vpeak. The simultaneous onset of both current and voltage limiting occurs when ROUT = 6Vpeak/20mA = 300Ω (typ) for a maximum POUT = 17.8dBm. This calculation applies for a sinusoidal signal. For nonsinusoidal signals, use the appropriate crest factor to calculate the actual maximum power that avoids output clipping. Although the instantaneous AC voltage on the OUT+ or OUT– pins may in some situations safely exceed 8V (with respect to ground), in no case should the DC voltage on these pins be allowed to exceed the ABSMAX tested limit of 7V. For nonoptimal ROUT values, the maximum available output power will be lower and can be calculated (considering current limiting for ROUT < 300Ω, and voltage limiting for ROUT > 300Ω). The result of this calculation is shown in Figure 7. The LT5524 input should not be overdriven (PIN > –11.5dBm at maximum gain). The consequences of overdrive are reduced bandwidth and, when the frequency is greater than 50MHz, reduced output power. At reduced gain settings, the maximum PIN is increased by an amount equal to the gain reduction. Input Bias Voltage The LT5524 IN+, IN– signal inputs are internally biased to 1.48V common mode when enabled, and to 1.26V in VCC = VCCO = 5V CURRENT LIMIT 20 POUT(MAX) (dBm) The LT5524 is a class A amplifier. To avoid signal distortion, the user must ensure that the LT5524 outputs do not enter into current or voltage limiting. The following discussion applies to maximum gain operation. 25 VOLTAGE LIMIT 15 10 5 0 20 100 1000 2000 ROUT (Ω) 5524 F07 Figure 7. Maximum Output Power as a Function of ROUT shutdown mode. These inputs are typically coupled by means of a capacitor or a transformer to a signal source, and impedance matching is assumed. In shutdown mode, the internal bias can handle up to 1µA leakage on the input coupling capacitors. This reduces the turn-on delay due to the input coupling RC time constant when exiting shutdown mode. If DC coupling to the input is required, the external common mode bias should track the LT5524’s internal common mode level. The DC current from the LT5524 inputs should not exceed IIN(SINK) = –200µA and IIN(SOURCE) = 400µA. Stability Considerations The LT5524’s open-loop architecture allows it to drive any practical load. Note that LT5524 gain is proportional to the load impedance, and may exceed the reverse isolation at frequencies above 1GHz if the LT5524’s outputs are left unloaded, with instability as the undesirable consequence. In such cases, placing a resistive differential load (e.g., 4k) or a small capacitor at the LT5524 outputs can be used to limit the maximum gain. The LT5524 has about 20GHz gain-bandwidth product. Hence, attention must be paid to the printed circuit board layout to avoid output pin to input pin signal coupling (the evaluation board layout is a good example). Due to the LT5524’s internal power supply regulator, external supply decoupling capacitors typically are not required. Likewise, decoupling capacitors on the LT5524 control inputs typically are not needed. Note, however, that the Exposed Pad 5524f 10 LT5524 U W U U APPLICATIO S I FOR ATIO on the LT5524 package must be soldered to a good ground plane on the PCB. PGA Function, Linearity and NF As described in the Circuit Operation section, the LT5524 consists of a variable (step) attenuator followed by a high gain output amplifier. The overall gain of the LT5524 is digitally controlled by means of four gain control pins with internal pull-down. Minimum gain is programmed when the gain control pins are set low or left floating. In shutdown mode, these PGA inputs draw <10µA leakage current, regardless of the applied voltage. The 6dB and 12dB attenuation steps (PGA2 and PGA3) are implemented by switching the amplifier inputs to an input attenuator tap. The 3dB attenuation step (PGA1) changes the amplifier transconductance. The output IP3 is approximately independent of the PGA1, PGA2 and PGA3 gain settings. However, the 1.5dB attenuation step utilizes a current steering technique that disables the internal linearity compensation circuit, and the OIP3 can be reduced by as much as 6dB when PGA0 is low. Therefore, to achieve the LT5524’s highest linearity performance, the PGA0 pin should be set high. The LT5524 noise figure is 8.6dB at 100MHz in the maximum gain state. For the –3dB attenuation setting, the NF is 9.2dB. The noise figure increases in direct proportion to the amount of programmed gain reduction for the 1.5dB, 6dB and 12dB steps. The output noise floor is proportional to the output load impedance, ROUT. It is almost constant for PGA1 = high and for any PGA0, PGA2, PGA3 state. When PGA1 = low, the output noise floor is 2dB lower (see Typical Performance Characteristics). Other Linearity Considerations LT5524 linearity is a strong function of signal frequency. OIP3 decreases about 13dB for every octave of frequency increase above 100MHz. As noted in the Circuit Operation section, at any given frequency and input level, the LT5524 provides a current output with fairly constant intermodulation distortion figure in dBc, regardless of the output load value. For higher ROUT values, more gain and output power is available, and better OIP3 figures can be achieved. However, high ROUT values are not easily implemented in practice, limited by the availability of high ratio output impedance transformation networks. Linearity can also be limited by the output RC time constant (bandwidth limitations), particularly for high ROUT values. A solution is outlined in the Bandpass Applications section. The LT5524 linearity degrades when common mode signal is present. The input transformer center tap should be decoupled to ground to provide a balanced input differential signal and to avoid linearity degradation for high attenuation steps. When the signal frequency is lower than 50MHz, and there is significant common mode signal, then high attenuation settings may result in degraded linearity. At signal frequencies below 100MHz, the LT5524’s internal linearity compensation circuitry may provide “sweet spots” with very high OIP3, in excess of +52dBm. This almost perfect distortion correction cannot be sustained over the full operating temperature range and with variations of the LT5524 output load (complex impedance ZOUT). Users are advised to rely on data shown in the Typical Performance Characteristics curves to estimate the dependable linearity performance. Wideband Applications At low frequencies, the value of the decoupling capacitors, choke inductors and choice of transformer will set the minimum frequency of operation. Output DC coupling is possible, but this typically reduces the LT5524’s output DC bias voltage, and thus the output swing and available power. At high frequencies, the output RC time constants set an upper limit to the maximum frequency of operation in the case of the wideband output networks presented so far. For example the LT5524 output capacitance, COUT = 1.7pF, and a pure resistive load, ROUT = 200Ω, will set the –3dB bandwidth to about 400MHz. In an actual application, the RLOAD • CLOAD product may be even more restrictive. The use of wideband output networks will not only limit the 5524f 11 LT5524 U W U U APPLICATIO S I FOR ATIO bandwidth, but will also degrade linearity because part of the available power is wasted driving the capacitive load. The LT5524’s output reactance is capacitive. Therefore improved AC response is possible by using external series output inductors. When driving purely resistive loads, an inductor in series with the LT5524 output may help to achieve maximally flat AC response as exemplified in the characterization setup schematic (Figure 9). The series inductor can extend the application bandwidth, but it provides no improvement in linearity performance. Series inductance may also produce peaking in the AC response. This can be the case when (high Q) choke inductors are used in an output interface such as in Figure 5, and the PCB trace (connection) to the load is too long. Since the LT5524’s output impedance is relatively high, the PCB trace acts as a series inductor. The most direct solution is to shorten the connection lines by placing the driver closer to the load. Another solution to flatten the AC response is to place resistance close to the LT5524 outputs. In this way the connection line behaves more like a terminated transmission line, and the AC peaking due to the capacitive load can be removed. Bandpass Applications For narrow band IF applications, the LT5524’s output capacitance and the application load capacitance can be incorporated as part of an LC impedance transformation network, giving improved linearity performance for signal frequencies greater than 100MHz. Figure 8 is an example of such a network. The network consists of two parallel resonant LC tank circuits critically coupled by capacitors C1 and C2. The ROUT to RLOAD transformation ratio in this particular implementation is 2. The choice of impedance transformation ratio is more flexible than in the wideband case. The LC network is a bandpass filter, a useful feature in many applications. A variety of bandpass matching network configurations are conceivable, depending on the requirements of the particular application. The design of these networks is facilitated by the fact that the LT5524 outputs are not destabilized by reactive loading. Note that these LC networks may distort the output signal if their amplitude and phase response exhibit nonlinear behavior. For example, if resistors R1 and R2 in Figure 5 are replaced with LC resonant tank circuits, then severe OIP3 degradation may occur. Low Output Noise Floor Applications In some applications the maximum output noise floor is specified. The LT5524 output noise floor is elevated above the available noise power (–174dBm/Hz into 50Ω) by the NF + Gain. Consequently, reduction of the LT5524’s power gain is the only way to reduce the output noise floor. NOTE: C3 + CLOAD = 12pF C4 + CLOAD = 12pF VCC T1 1:2 L5 56nH C8 0.1µF IN+ VSRC TC2-1T C9 0.33µF IN– C3 LT5524 + ROUT 200Ω C6 2.2pF C2 12pF C5 5.6pF L4 56nH RLOAD 100Ω C4 GAIN = 27dB PGA0 PGA1 PGA2 PGA3 L3 56nH – DUT RSRC 50Ω L6 C1 56nH 12pF VOSUP C7 0.1µF RLOAD 50Ω CLOAD RLOAD 50Ω CLOAD 1dB BANDWIDTH: fL = 130MHz fU = 220MHz 5524 F08 Figure 8. Bandpass Output Transformation Network Example 5524f 12 LT5524 U W U U APPLICATIO S I FOR ATIO Rather, it represents a compromise that most accurately measures the actual operation of the part by itself, undistorted by the artifacts of the impedance transformation network, or by external bandwidth limiting factors. Balun transformers are used to interface with single-ended test equipment. Input and output resistive attenuators (not shown) provide broadband I/O impedance control. The L1, L2 inductors are selected for maximally flat AC output response. COUT (normally open) shows the placement of capacitive loading when this is specified as a characterization variable. The VCCO monitor pin allows setting the output DC level (5V typical) by adjusting voltage VOSUP. In fixed gain applications, the LT5524 can be set to 3dB attenuation relative to maximum gain. As shown in the Typical Performance Characteristics, this gives a 2dB reduction in the output noise floor with no loss of linearity. In general, the output noise floor can be reduced by decreasing ROUT (and hence power gain), at the cost of reduced OIP3. LT5524 Characterization The LT5524’s typical performance data are based on the test circuits shown in Figures 9 and 10. Figure 9 does not necessarily reflect the use of the LT5524 in an actual application. (For that, see the Application Boards section.) VCC R9 35.7Ω C1 0.33µF C7 47nF T1 1:1 RSRC 50Ω VSRC R10 35.7Ω C2 0.1µF COUT (OPT) R7 35.7Ω C8 47nF IN+ R8 35.7Ω LT5524 IN– ROUT + R5 51k R6 51k R3 37.4Ω L2 (OPT) R4 37.4Ω C5 47nF T1 1:1 C6 47nF RLOAD 50Ω COUT (OPT) VCCO MONITOR PGA0 PGA1 PGA2 PGA3 L1 (OPT) VOSUP C3 4.7µF C4 0.1µF R2 25Ω – DUT ATT = 7.7dB ETC-11-13 R1 25Ω ETC-11-13 ROUT R3, R4 ATT L1, L2 100Ω 37.4Ω 9dB 0Ω 200Ω 87.4Ω 12dB 33nH 5524 F09 Figure 9. Characterization Board (Simplified Schematic) VCC C2 0.1µF IF IN T1 1:2 C1 0.47µF J1 0Ω TC2-1T TRANSFORMER DEMO BOARD EN 1 2 3 4 5 6 7 8 9 10 PGA0 PGA1 VOSUP EN NC VCC1 VCC2 GND GND LT5524 GND GND IN+ OUT– IN– OUT+ GND GND GND GND PGA0 PGA3 PGA1 PGA2 20 NC 19 18 17 16 15 14 13 12 11 C4 0.1µF C3 4.7µF IF OUT T2 4:1 ROUT 100Ω • • RMATCH 255Ω • TC4-1W RLOAD 50Ω J2 0Ω PGA2 PGA3 5524 F10 Figure 10. Output Transformer Application Board (Simplified Schematic) 5524f 13 LT5524 U W U U APPLICATIO S I FOR ATIO Application (Demo) Boards (T2 transformer). For the Typical Performance Characteristics curves, all linearity tests are performed on this board. By removing RMATCH, the performance with ROUT = 200Ω can be evaluated (provided the lack of impedance back-matching is suitably remedied). The LT5524 demo boards are provided in the versions shown in Figure 10 (with output transformer) and Figure 11 (without output transformer). All I/O signal ports are matched to 50Ω. Moreover, 40k resistors (not shown) connect all five control pins (EN, PGA0, PGA1, PGA2, PGA3) to VCC, such that the LT5524 is shipped in maximum gain state. The transformer board can provide a differential output when Jumper J2 is removed. The Wideband Differential Output Application Board (Figure 11) is an example of direct coupling (no transformer) to the load, and has wider output bandwidth. This board gives direct access to the LT5524’s output pins, and was used for stability tests. Higher VOSUP (6.5V) is required to compensate for the DC voltage drop on R1 and R2. Use TP2, TP3 to monitor the actual LT5524 output bias voltage. By replacing R1 and R2 with inductors, this board can operate with a 5V supply. However, this may limit the minimum signal frequency. For example, an 820nH choke inductor will limit the lowest signal frequency to 40MHz. The gain setting can be changed by connecting the control pins to ground. Test points (TP1, TP2, TP3) are provided to monitor the input and output DC bias voltage. Jumper J1 can be removed when differential input is desired, but in that case, T1 should be changed to a 1:1 center-tap transformer to preserve 50Ω input matching. The demo board is shipped with optional output back-matching resistor RMATCH = 255Ω. This results in a net output load, ROUT = 100Ω, presented to the LT5524. The Output Transformer Application Board (Figure 10) is one example of an output impedance transformation VCC C2 0.1µF IF IN T1 1:2 J1 0Ω TC2-1T DIFFERENTIAL OUTPUT RESISTIVE DEMO BOARD C1 0.47µF EN VOSUP 1 2 3 4 5 6 7 8 9 10 PGA0 PGA1 EN NC VCC1 VCC2 GND GND LT5524 GND GND IN+ OUT– IN– OUT+ GND GND GND GND PGA0 PGA3 PGA1 PGA2 20 19 18 17 16 15 14 13 12 11 R1 50Ω NC ROUT 50Ω R2 50Ω C4 0.1µF C5 47nF C6 47nF C3 4.7µF IF OUT RLOAD 100Ω J2 0PEN PGA2 PGA3 5524 F11 Figure 11. Wideband Differential Output Application Board (Simplified Schematic) 5524f 14 LT5524 U PACKAGE DESCRIPTIO FE Package 20-Lead Plastic TSSOP (4.4mm) (Reference LTC DWG # 05-08-1663) Exposed Pad Variation CB 6.40 – 6.60* (.252 – .260) 3.86 (.152) 3.86 (.152) 20 1918 17 16 15 14 13 12 11 6.60 ±0.10 2.74 (.108) 4.50 ±0.10 6.40 2.74 (.252) (.108) BSC SEE NOTE 4 0.45 ±0.05 1.05 ±0.10 0.65 BSC 1 2 3 4 5 6 7 8 9 10 RECOMMENDED SOLDER PAD LAYOUT 4.30 – 4.50* (.169 – .177) 0.09 – 0.20 (.0035 – .0079) 0.25 REF 0.50 – 0.75 (.020 – .030) NOTE: 1. CONTROLLING DIMENSION: MILLIMETERS MILLIMETERS 2. DIMENSIONS ARE IN (INCHES) 3. DRAWING NOT TO SCALE 1.20 (.047) MAX 0° – 8° 0.65 (.0256) BSC 0.195 – 0.30 (.0077 – .0118) TYP 0.05 – 0.15 (.002 – .006) FE20 (CB) TSSOP 0204 4. RECOMMENDED MINIMUM PCB METAL SIZE FOR EXPOSED PAD ATTACHMENT *DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.150mm (.006") PER SIDE 5524f Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 15 LT5524 RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LT5511 High Linearity Upconverting Mixer RF Output to 3GHz, 17dBm IIP3, Integrated LO Buffer LT5512 DC-3GHz High Signal Level Downconverting Mixer DC to 3GHz, 21dBm IIP3, Integrated LO Buffer LT5514 Ultralow Distortion IF Amplifier/ADC Driver with Digitally Controlled Gain 47dBm OIP3 at 100MHz, 33dB Maximum Gain, 22.5dB Gain Control Range LT5515 1.5GHz to 2.5GHz Direct Conversion Quadrature Demodulator 20dBm IIP3, Integrated LO Quadrature Generator LT5516 0.8GHz to 1.5GHz Direct Conversion Quadrature Demodulator 21.5dBm IIP3, Integrated LO Quadrature Generator LT5517 40MHz to 900MHz Quadrature Demodulator 21dBm IIP3, Integrated LO Quadrature Generator LT5519 0.7GHz to 1.4GHz High Linearity Upconverting Mixer 17.1dBm IIP3 at 1GHz, Integrated RF Output Transformer with 50Ω Matching, Single-Ended LO and RF Ports Operation LT5520 1.3GHz to 2.3GHz High Linearity Upconverting Mixer 15.9dBm IIP3 at 1.9GHz, Integrated RF Output Transformer with 50Ω Matching, Single-Ended LO and RF Ports Operation LT5521 3.7GHz Very High Linearity Upconverting Mixer 24.2dBm IIP3 at 1.9GHz, Wide 3.15V to 5.25V Supply Range, –5dBm LO Drive, –42dBm LO-RF Leakage LT5522 600MHz to 2.7GHz High Signal Level Downconverting Mixer 4.5V to 5.25V Supply, 25dBm IIP3 at 900MHz, NF = 12.5dB, 50Ω Single-Ended RF and LO Ports LT5526 High Linearity, Low Power Downconverting Mixer 16.5dBm IIP3, 0.6dB Gain, 11dB NF at 900MHz, 28mA Supply Current Infrastructure RF Power Detectors LT5504 800MHz to 2.7GHz RF Measuring Receiver 80dB Dynamic Range, Temperature Compensated, 2.7V to 5.25V Supply LTC®5505 RF Power Detectors with >40dB Dynamic Range 300MHz to 3GHz, Temperature Compensated, 2.7V to 6V Supply LTC5507 100kHz to 1000MHz RF Power Detector 100kHz to 1GHz, Temperature Compensated, 2.7V to 6V Supply LTC5508 300MHz to 7GHz RF Power Detector 44dB Dynamic Range, Temperature Compensated, SC70 Package LTC5509 300MHz to 3GHz RF Power Detector 36dB Dynamic Range, Low Power Consumption, SC70 Package LTC5530 300MHz to 7GHz Precision RF Power Detector Precision VOUT Offset Control, Shutdown, Adjustable Gain LTC5531 300MHz to 7GHz Precision RF Power Detector Precision VOUT Offset Control, Shutdown, Adjustable Offset LTC5532 300MHz to 7GHz Precision RF Power Detector Precision VOUT Offset Control, Adjustable Gain and Offset LT5534 50MHz to 3GHz Wide Dynamic Range Log RF Power Detector 60dB Dynamic Range, Superb Temperature Stability and Accuracy, Low Supply Current, SC70 Package LTC5535 Precision RF Detector with 12MHz Baseband Bandwidth 600MHz to 7GHz Adjustable Gain, Precision VOUT Offset Control Low Voltage RF Building Blocks LT5500 1.8GHz to 2.7GHz Receiver Front End 1.8V to 5.25V Supply, Dual-Gain LNA, Mixer, LO Buffer LT5502 400MHz Quadrature IF Demodulator with RSSI 1.8V to 5.25V Supply, 70MHz to 400MHz IF, 84dB Limiting Gain, 90dB RSSI Range LT5503 1.2GHz to 2.7GHz Direct IQ Modulator and Upconverting Mixer 1.8V to 5.25V Supply, Four-Step RF Power Control, 120MHz Modulation Bandwidth LT5506 500MHz Quadrature IF Demodulator with VGA 1.8V to 5.25V Supply, 40MHz to 500MHz IF, –4dB to 57dB Linear Power Gain, 8.8MHz Baseband Bandwidth LT5546 500MHz Ouadrature IF Demodulator with VGA and 17MHz Baseband Bandwidth 17MHz Baseband Bandwidth, 40MHz to 500MHz IF, 1.8V to 5.25V Supply, –7dB to 56dB Linear Power Gain 5524f 16 Linear Technology Corporation LT/TP 0904 1K • PRINTED IN THE USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com © LINEAR TECHNOLOGY CORPORATION 2004