SMU01 1W DC-DC Unregulated Single Output Converter series Features : 1500VDC I/O isolation 3000VDC I/O isolation(optional) Operating temperature range of -40 ~ +85 Internal SMD technology Built-in EMI filter Cooling by free air convection Non-conductive plastic case SIP packge Industry standard pinout 100% burn-in test Low cost / High reliability 2 years warranty SELECTION GUIDE ORDER NO. SMU01M-05 SMU01L-05 SMU01N-05 DC OUTPUT VOLTAGE 5V OUTPUT CURRENT RANGE 0 ~ 200mA EFFICIENCY(Typ.) 77% 79% 78% SMU01L-12 SMU01M-12 SMU01N-12 DC OUTPUT VOLTAGE 12V OUTPUT CURRENT RANGE 0 ~ 84mA EFFICIENCY(Typ.) 78% ORDER NO. without derating SMU01M-09 SMU01N-09 77% 79% 76% SMU01L-15 SMU01M-15 SMU01N-15 SMU01L-09 9V 0 ~ 110mA 15V 0 ~ 67mA 77% 78% 80% 77% 10.8 ~ 13.2V 12V 21.6 ~ 26.4V 24V 4.5 ~ 5.5V 5V 10.8 ~ 13.2V 12V 21.6 ~ 26.4V 24V Full load 265mA No load 32mA 110mA 57mA 265mA 110mA 57mA 15mA 11mA 32mA 15mA 11mA PROTECTION (FUSE RECOMMENDED) 500mA 250mA 150mA 500mA 250mA 150mA 80% SPECIFICATION RATED POWER OUTPUT 1W RIPPLE & NOISE (max.) Note.2 100mVp-p LINE REGULATION Note.3 1.2% for 1% input variation LOAD REGULATION Note.4 8.0% VOLTAGE ACCURACY 2.0% SWITCHING FREQUENCY(Typ.) 100KHz 4.5 ~ 5.5V 5V VOLTAGE RANGE NORMAL VOLTAGE INPUT CURRENT INPUT FILTER Capacitor type Momentary OVERLOAD Protection type : Broken Momentary PROTECTION SHORT CIRCUIT Protection type : Broken WORKING TEMP. -40 ~ +90 WORKING HUMIDITY 20% ~ 90% RH non-condensing (Refer to output load derating curve) ENVIRONMENT STORAGE TEMP., HUMIDITY -55 ~ +125 , 10 ~ 95% RH 0.05% / (0 ~ 50 ) TEMP. COEFFICIENT 10 ~ 500Hz, 2G 10min./1 cycle, period for 60min. each along X, Y, Z axes VIBRATION WITHSTAND VOLTAGE I/P-O/P:1.5KVDC I/P-O/P: 100M Ohms / 500VDC / 25 / 70% RH ISOLATION RESISTANCE SAFETY & 80pF max. ISOLATION CAPACITANCE EMC Compliance to EN55022 Class B, FCC part 15 Class B EMI RADIATION Compliance to EN61000-4-2,3,4,5,6,8 light industry level, criteria A EMS IMMUNITY OTHERS MTBF DIMENSION (L*W*H) 700khrs min. MIL-HDBK-217F(25 WEIGHT 1.3g ) 11.6*6.1*10.14mm or 0.46"*0.24"*0.40" inch for 5V,12V input ; 11.6*7.4*10.14mm or 0.46"*0.29"*0.40" inch for 24V input Mechanical Specification Unit: mm (inch) Derating Curve Pin Configuration FRONT VIEW 1.2 (0.05) 1 2 3 4 Pin No. Output 1 -Vin 2 3 +Vin -Vout 4 +Vout 100 LOAD (%) 6.10 (0.24) 10.14 (0.40) 11.6 (0.46) 50 BOTT ON VIEW 3.81 (0.15) 2.54 (0.10) -40 NOTE 0 20 40 60 85 90 100 Ta ( ) 1.All parameters are specified at normal input, rated load, 25 70% RH ambient. 2.Ripple & noise are measured at 20MHz by using a 12" twisted pair terminated with a 0.1uf & 47uf capacitor. 3.Line regulation is measured from low line to high line at rated load. 4.Load regulation is measured from 20% to 100% rated load. File Name: SMU01-SPEC 2009-10-12