MIC3223 High Power Boost LED Driver with Integrated FET General Description Features The MIC3223 is a constant current boost LED driver capable of driving a series string of high power LEDs. The MIC3223 can be used in general lighting, bulb replacement, garden pathway lighting and other solid state illumination applications. The MIC3223 is a peak current mode control PWM boost regulator and the 4.5V and 20V operating input voltage range allows multiple applications from a 5V or a 12V bus. The MIC3223 implements a fixed internal 1MHz switching frequency to allow for a reduction in the design footprint size. Power consumption has been minimized through the implementation of a 200mV feedback voltage that provides an accuracy of ±5%. The MIC3223 can be dimmed through the use of a PWM signal and features an enable pin for a low power shutdown state. The MIC3223 is a very robust LED driver and offers the following protection features: over voltage protection (OVP), thermal shutdown, switch current limiting and under voltage lockout (UVLO). The MIC3223 is offered in a low profile exposed pad 16-pin TSSOP package. Data sheets and support documentation can be found on Micrel’s web site at: www.micrel.com. • • • • • • • • • 4.5V to 20V supply voltage 200mV feedback voltage with an accuracy of ±5% Step-up output voltage (boost) conversion up to 37V 1MHz switching frequency 100mΩ/3.5A internal power FET switch LEDs can be dimmed using a PWM signal User settable LED current (through external resistor) Externally programmable soft-start Protection features that include: – Output over-voltage protection (OVP) – Under-voltage lockout (UVLO) – Over temperature protection • Junction temperature range: -40°C to +125°C • Available in a exposed pad 16-pin TSSOP package Applications • • • • • • Architectural lighting Industrial lighting Signage Landscape lighting (garden/pathway) Under cabinet lighting MR-16 bulbs _______________________________________________________________________________________________________________________ Typical Application Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com January 2010 M9999-011510-A Micrel, Inc. MIC3223 Ordering Information Part Number Junction Temp. Range Package Lead Finish –40° to +125°C 16-pin ePad TSSOP PB- free MIC3223YTSE Pin Configuration 16-Pin ePad TSSOP (TSE) Pin Description Pin Number Pin Name 1 EN Enable (Input): Logic high enables and logic low disables operation. 2 SS Soft Start (Input resistance of 30k). Connect a capacitor to GND for soft-start. Clamp the pin to a known voltage to control the internal reference voltage and hence the output current. 3 COMP 4 FB 5 OVP 6 PGND 7,8,9,10 SW 11 VIN 12 DRVVDD 13 VDD 14 DIM_IN 15 DIM_OUT 16 AGND 17 EP January 2010 Pin Function Compensation Pin (Input): Add external R and C-to-GND to stabilize the converter. Negative Input to Error Amp Connect to the centre tap of an external resistor divider, the top of which is tied to Vout and bottom-to-ground. Power Ground Switch Node (Input): Internal NMOS switch Drain Pin Input Supply For 4.5V < VIN < 6V, connect DRVVDD to VIN. DRVVDD is the input voltage supply for the converter’s internal power FET gate driver. For VIN > 6V, connect this pin to VDD. For 4.5V < VIN < 6V, this pin becomes the input voltage supply for the converter’s internal circuit. For VIN > 6V, this pin is an output of the internal 5.5V regulator that supplies internal circuits. User must add 10µF decoupling capacitor from VDD-to-AGND. PWM input to control LED dimming. Output driver to drive external FET for LED dimming. Analog Ground Connect to Power Ground 2 M9999-011510-A Micrel, Inc. MIC3223 Absolute Maximum Ratings(1) Operating Ratings(2) Supply Voltage (VIN) .....................................................+22V Switch Voltage (VSW)..................................... -0.3V to +42V Regulated Voltage (VDD) ............................... -0.3V to +6.5V Dimming In Voltage (VDIM_IN) ...............-0.3V to (VDD + 0.3V) Dimming Out Voltage (VDIM_OUT)..........-0.3V to (VDD + 0.3V) Soft-Start Voltage (VSS) .......................-0.3V to (VDD + 0.3V) Enable Voltage (VEN)............................-0.3V to (VIN + 0.3V) Feedback Voltage (VFB) ......................-0.3V to (VDD + 0.3V) Switch Current (ISW) ..................................Internally Limited Comp Voltage (VCOMP).......................-0.3V to (+VDD + 0.3V) FET Driver Supply (VDRVVDD) ......................... -0.3V to +6.5V PGND to AGND ............................................ -0.3V to +0.3V Over Voltage Protection (VOVP) ...........-0.3V to (VDD + 0.3V) Peak Reflow Temperature (soldering, 10-20sec.) ..... 260°C Storage Temperature (TS)..........................-65°C to +150°C ESD Rating(3) ................................................................+2kV Supply Voltage (VIN)...................................... +4.5V to +20V Switch Voltage (VSW)....................................................+37V Junction Temperature (TJ) .........................-40°C to +125°C Junction Thermal Resistance ePad TSSOP-16L (θJA)...................................36.5°C/W Electrical Characteristics(4) VIN = VEN = 12V; L = 22µH, CIN =4.7µF, COUT =2x4.7µF; TA = 25°C, BOLD values indicate –40°C≤ TJ ≤ +125°C, unless otherwise noted. Symbol Parameter VIN Voltage Supply Range VUVLO Under Voltage Lockout VOVP Over Voltage Protection IVIN Quiescent Current ISD Shutdown Current VFB Feedback Voltage IFB Feedback Input Current VDD Internal Voltage Regulator DMAX Maximum Duty Cycle VDD Line Regulation Condition Min Typ 4.5 Monitoring for VDD Max Units 20 V 3 3.7 4.4 V 1.216 1.28 1.344 V 2.1 5 mA 10 µA 200 210 mV 216 mV VFB=250mV VEN =0V Room Temperature 190 Over Temperature 184 VFB=200mV 85 VLED=18V, VIN=8V to 16V, ILED=350mA -450 nA 5.3 V 90 95 0.5 9 % ISW Switch Current Limit RSW Switch RDSON plus RCS ISW Switch Leakage Current VEN Enable Threshold IEN Enable Pin Current VDIM_TH_H DIM_IN Threshold High Logic High VDIM_TH_L DIM_IN Threshold Low Logic Low Hys DIM_IN Hysteresis IDIM_IN DIM_IN Pin Current VDIM_IN = 5V TDR Dim Delay (Rising) DIM_IN Rising 40 ns TDF Dim Delay (Falling DIM_IN Falling 30 ns January 2010 3.5 % 10.5 100 VEN=0, VSW=37V 0.01 Turn On mΩ 10 1.5 µA V Turn Off 20 0.4 V 40 µA 1.5 V 0.4 500 V mV 1 3 A µA M9999-011510-A Micrel, Inc. MIC3223 Symbol Parameter DIM MIN Minimum Dimming Pulse RDO DIM_OUT Resistance High RDO DIM_OUT Resistance Low Condition Min Typ Max Units DIM_IN =1µs CDIM_OUT = 1.25nF 0.7 1.3 µs DIM_OUT measured from 4V rising to 2.5 falling 0.5 1.5 µs DIM_OUT pull up resistance IDIM_OUT = +2mA Dim Out pull down resistance IDIM_OUT = -2mA 70 Ω 40 Ω FSW Oscillator Frequency 0.7 1 1.3 MHz RSS Soft Start Resistance 30 46 62 kΩ TSD Over Temperature Threshold Shutdown Temperature rising 165 °C Hysteresis 10 °C Notes 1. Exceeding the absolute maximum rating may damage the device. 2. The device is not guaranteed to function outside its operating rating. 3. Devices are ESD sensitive. Handling precautions recommended. Human body model, 1.5kΩ in series with 100pF. 4. Specification for packaged product only. Test Circuit January 2010 4 M9999-011510-A Micrel, Inc. MIC3223 Typical Characteristics 98 5.50 T = 25°C 96 9.5 5.45 5.40 92 90 88 86 84 82 5.35 5.30 5.25 5.20 5.15 VOUT = 25V 5.10 IOUT = 0.5A 5.05 80 9.0 T = 25°C CURRENT LIM IT (A) VDD VOLTAGE (V) 94 EFFICIENCY (%) Current Lim it v s. Input Voltage VDD Voltage v s. Input Voltage Efficiency v s. Input Voltage VOUT = 25V 10 15 20 5 10 INPUT VOLT AGE (V) 7.5 7.0 15 4 20 1.2 0.220 0.218 0.204 0.202 0.200 0.198 0.196 0.194 VOUT = 30V 0.192 IOUT =0.36A T = 25°C 1.1 FEEDBACK VOLTAGE (V) SWITCHING FREQUENCY (MHz) 0.206 1.1 1.0 VDD = VIN VIN = 4.5V to 6V 1.0 VOUT = 30V IOUT = 0.36A 4 9 14 4 19 0.216 0.214 0.212 0.210 0.208 0.206 9 INPUT VOLT AG E (V) VOUT = 26V 0.202 IOUT = 0.36A 14 -40 19 RSW _NODE vs. T emperature 1.20 0.17 1.15 SWITCHING FREQUENCY (MHz) 0.18 10.0 0.16 RSW_NO DE (Ω) 9.5 9.0 8.5 8.0 7.5 7.0 0.15 0.14 0.13 VIN = 12V 0.12 VOUT = 36V 0.11 VIN = 12V ISW = 1.3A 0.10 6.0 20 40 60 80 -40 100 120 -20 0 20 40 60 Efficiency v s. Output Current 80 8V 86 84 82 80 0.5 1 OUT PUT CURRENT (A) January 2010 1.5 IOUT = 0.36A -20 0 20 40 60 80 100 120 Efficiency v s. Output Current 20V 94 14V 90 88 86 84 18V 92 90 88 86 84 82 VOUT = 25V VOUT = 25V 80 80 0 VOUT = 26V 0.85 96 82 VOUT = 25V VIN = 12V 0.90 T EM PERAT URE (°C) EFFICIENCY (%) EFFICIENCY (%) 10V 88 0.95 98 92 90 100 120 1.00 -40 16V 94 92 80 0.80 100 120 96 12V 94 60 1.05 Efficiency v s. Output Current 96 40 1.10 T EM PERAT URE (°C) T EM PERAT URE (°C) 20 Switching Frequency v s. Temperature 10.5 0 0 T EM PERAT URE (°C) 11.0 -20 -20 INPUT VOLT AGE (V) Current Lim it v s. Temperature 6.5 VIN = 12V 0.204 0.200 0.9 0.190 CURRENT LIM IT (A) 19 Feedback Voltage v s. Temperature 0.208 EFFICIENCY (%) 14 INPUT VOLT AGE (V) Switching Frequency v s. Input Voltage 0.210 -40 9 INPUT VOLT AGE (V) Feedback Voltage v s. Input Voltage REFERENCE VOTLAG E (V) 8.0 VIN = 4.5V to 6V IOUT = 0.5A 5.00 5 T = 25°C 8.5 0 0.5 1 OUT PUT CURRENT (A) 5 1.5 0 0.5 1 1.5 OUT PUT CURRENT (A) M9999-011510-A Micrel, Inc. MIC3223 Typical Characteristics (continued) Efficiency v s. Output Current Efficiency v s. Output Current 96 96 94 94 92 10V EFFICIENCY (%) EFFICIENCY (%) 92 90 88 86 84 82 12V 90 88 86 84 82 VOUT = 25V 80 VOUT = 25V 80 0 0.5 1 OUT PUT CURRENT (A) January 2010 1.5 0 0.5 1 1.5 OUT PUT CURRENT (A) 6 M9999-011510-A Micrel, Inc. MIC3223 Functional Characteristics January 2010 7 M9999-011510-A Micrel, Inc. MIC3223 Functional Characteristics (continued) January 2010 8 M9999-011510-A Micrel, Inc. MIC3223 Functional Diagram January 2010 9 M9999-011510-A Micrel, Inc. MIC3223 current is regulated. If VFB drops, VEA increases and therefore the power FET remains on longer so that VCS can increase to the level of VEA. The reverse occurs when VFB increases. Functional Description A constant current output converter is the preferred method for driving LEDs. Small variations in current have a minimal effect on the light output, whereas small variations in voltage have a significant impact on light output. The MIC3223 LED driver is specifically designed to operate as a constant current LED Driver. The MIC3223 is designed to operate as a boost converter, where the output voltage is greater than the input voltage. This configuration allows for the design of driving multiple LEDs in series to help maintain color and brightness. The MIC3223 can also be configured as a SEPIC converter, where the output voltage can be either above or below the input voltage. The MIC3223 has an input voltage range, from 4.5V and 20V, to address a diverse range of applications. In addition, the LED current can be programmed to a wide range of values through the use of an external resistor. This provides design flexibility in adjusting the current for a particular application need. The MIC3223 features a low impedance gate driver capable of switching large MOSFETs. This low impedance provides higher operating efficiency. The MIC3223 can control the brightness of the LEDs via its PWM dimming capability. Applying a PWM signal (up to 20kHz) to the DIM_IN pin allows for control of the brightness of the LEDs. The MIC3223 boost converter employs peak current mode control. Peak current mode control offers advantages over voltage mode control in the following manner. Current mode control can achieve a superior line transient performance compared to voltage mode control and is easier to compensate than voltage mode control, thus allowing for a less complex control loop stability design. Page 9 of this datasheet shows the functional block diagram. PWM Dimming This control process just described occurs during each DIM_IN pulse and when ever DIM_IN is high. When DIM_IN is low, the boost converter will no longer switch and the output voltage will drop. For high dimming ratios use an external PWM Dimming switch as shown in the Typical Application. When the dim pulse is on the external switch is on and circuit operates in the closed loop control mode as described. When the DIM_IN is low the boost converter does not switch and the external switch is open and no LED current can flow and the output voltage does not droop. When DIM_IN goes high the external switch is driven on and LED current flows. The output voltage remains the same (about the same) during each on and off DIM_IN pulse. PWM Dimming can also be used in the Test Circuit in applications that do not require high dimming ratios. In the Test Circuit, the load is not removed from the output voltage between DIM_IN pulses and will therefore drain the output capacitors. The voltage that the output will discharge to is determined by the sum of the VF (forward voltage drops of the LEDs). When VOUT can no longer forward bias the LEDs, then the LED current will stop and the output capacitors will stop discharging. During the next DIM_IN pulse VOUT has to charge back up before the full LED current will flow. For applications that do not require high dimming ratios. Boost Converter operation The boost converter is a peak current mode pulse width modulation (PWM) converter and operates as follows. A flip-flop (FF) is set on the leading edge of the clock cycle. When the FF is set, a gate driver drives the power FET on. Current flows from VIN through the inductor (L) and through the power switch and also through the current sense resistor to PGND. The voltage across the current sense resistor is added to a slope compensation ramp (needed for stability). The sum of the current sense voltage and the slope compensation voltages (called VCS) is fed into the positive terminal of the PWM comparator. The other input to the PWM comparator is the error amp output (called VEA). The error amp’s negative input is the feedback voltage (VFB). VFB is the voltage across RADJ (R5). In this way the output LED January 2010 10 M9999-011510-A Micrel, Inc. MIC3223 Output Over Voltage Protection (OVP) The MIC3223 provides an OVP circuitry in order to protect the system from an overvoltage fault condition. This OVP threshold can be programmed through the use of external resistors (R3 and R4 in the Typical Application). A reference value of 1.245V is used for the OVP. Equation 3 can be used to calculate the resistor value for R9 to set the OVP point. Normally use 100k for R3. Application Information Constant Output Current Converter The MIC3223 is a peak current mode boost converter designed to drive high power LEDs with a constant current output. The MIC3223 operates with an input voltage range from 4.5V to 20V. In the boost configuration, the output can be set from VIN up to 37V. The peak current mode control architecture of the MIC3223 provides the advantages of superior line transient response as well as an easier to design compensation. The MIC3223 LED driver features a built-in soft start circuitry in order to prevent start-up surges. Other protection features include: DRVVDD An internal linear regulator is used to provide the necessary internal bias voltages to the gate driver that drives the external FET. When VIN is above 6V connect DRVVDD to VDD. When VIN is 6V or below connect the DRVVDD pin to VIN. Use a bypass capacitor, 10µF ceramic capacitor. • Over Voltage Protection (OVP) – output over voltage protection to prevent operation above a safe upper limit • Under Voltage Lockout (UVLO) – UVLO designed to prevent operation below a safe lower limit Setting the LED Current The current through the LED string is set via the value chosen for the current sense resistor RADJ which is R5 in the schematic of the Typical Application. This value can be calculated using Equation 1: ILED = UVLO Internal under voltage lock out (UVLO) prevents the part from being used below a safe VIN voltage. The UVLO is 3.7V. Operation below 4.5V is not recommended. 0.2V R ADJ Soft Start Soft start is employed to lessen the inrush currents during turn on. At turn on the following occurs; 1. After about 1.5ms CSS will start to rise in a exponential manner according to; Another important parameter to be aware of in the boost converter design is the ripple current. The amount of ripple current through the LED string is equal to the output ripple voltage divided by the LED AC resistance (RLED – provided by the LED manufacturer) plus the current sense resistor RADJ. The amount of allowable ripple through the LED string is dependent upon the application and is left to the designer’s discretion. The equation is shown in Equation 2. VSS ΔILED ≈ Where VOUTRIPPLE = (RLED + R ADJ ) ILED × D COUT × FSW Reference Voltage The voltage feedback loop the MIC3223 uses an internal voltage of 200mV with an accuracy of ±5%. The feedback voltage is the voltage drop across the current sense resistor as shown in the Typical Application. When in regulation the voltage at VFB will equal 200mV. January 2010 −t ⎛ ⎞ ⎜ (37kΩ×C SS ) ⎟ = 0.2⎜1 − e ⎟ ⎜ ⎟ ⎝ ⎠ 2. According to the block diagram, VSS is the ref node of the error amp. PWM switching start when VSS begins to rise. 3. When the CSS is fully charged, 0.2V will be at the error amp reference and steady state operation begins. 4. Design for soft-start time using the above equation. VOUTRIPPLE Eq. (2) R3 (VOVP /1.245) − 1 VDD An internal linear regulator is used to provide the necessary internal bias voltages. When VIN is 6V or below connect the VDD pin to VIN. Use a 10µF ceramic bypass capacitor. • Current Limit (ILIMIT) – Current sensing for over current and overload protection Eq. (1) R4 = Eq. (3) 11 M9999-011510-A Micrel, Inc. MIC3223 If high dimming ratios are required, a lower Dimming frequency is required. During each DIM_IN pulse the inductor current has to ramp up to it steady state value in order for the programmed LED current to flow. The smaller the inductance value the faster this time is and a narrower DIM_IN pulse can be achieved. But smaller inductance means higher ripple current. Figure 1. Soft start LED Dimming The MIC3223 LED driver can control the brightness of the LED string via the use of pulse width modulated (PWM) dimming. An input signal from DC up to 20kHz can be applied to the DIM_IN pin (see Typical Application) to pulse the LED string ON and OFF. It is recommended to use PWM dimming signals above 120Hz to avoid any recognizable flicker by the human eye. PWM dimming is the preferred way to dim an LED in order to prevent color/wavelength shifting. Color wavelength shifting will occur with analog dimming. By employing PWM Dimming the output current level remains constant during each DIM_IN pulse. The boost converter switches only when DIM_IN is high. Between DIM_IN pulses the output capacitors will slowly discharge. The higher the DIM_IN frequency the less the output capacitors will discharge. Figure 3. PWM Dimming 20% Figure 3 shows that switching occurs only during DIM_IN on pulses. When DIM_IN is low the boost converter stops switching and the external LED is turned off. The LED current flows only when DIM_IN is high. Figure 3 shows that the compensation pin (VCOMP) does not discharge between DIM_IN pulses. Therefore, when the DIM_IN pulse starts again the converter resumes operation at the same VCOMP voltage. This eliminates the need for the comp pin to charge up during each DIM_IN pulse and allows for high Dimming ratios. PWM Dimming Limits The minimum pulse width of the DIM_IN is determined by the DIM_IN frequency and the L and C used in the boost stage output filter. At low DIM_IN frequencies lower dimming ratios can be achieved. Dim_ratio = LED_ON_TIM E PERIOD PWMD Figure 4. PWM Dimming 10% and ILED 100Hz Figure 2. DIM_IN Dimming Ratio January 2010 12 M9999-011510-A Micrel, Inc. MIC3223 Figure 5. PWM Dimming 20% and ILED 1kHz Figure 7. 5µs DIM_IN Pulse In Figure 4 is at 100Hz dimming frequency and Figure 5 is 1kHz dimming frequency. The time it takes for the LED current to reach it full value is longer with a lower Dimming frequency. The reason is the output capacitors slowly discharge between dimming pulses. Figure 7 shows the minimum DIM_IN pulse at these operating conditions before the ILED current starts to drop due to low VOUT. The converter is ON (switching) only during a DIM_IN pulse. Figure 7 shows that at this DIM_IN pulse width the converter is ON (switching) long enough to generate the necessary VOUT to forward bias the LED string at the programmed current level. Therefore this condition will result in the desired ILED. Figure 6. PWM Dimming 20% and ILED 1kHz Figure 6 shows the output voltage VOUT discharge between DIM_IN pulses. The amount of discharge is dependent on the time between DIM_IN pulses. Figure 8. 2.5µs DIM_IN Pulse Figure 8 shows that at this DIM_IN pulse width the converter in not ON (switching) long enough to generate the necessary VOUT to forward bias the LED string at the programmed current level. As a result the LED current drops. Therefore, this condition will not result in the desired ILED. January 2010 13 M9999-011510-A Micrel, Inc. MIC3223 Design Procedure for a LED Driver Symbol Parameter Min Nom Max Units Input VIN Input Voltage IIN Input Current 8 12 14 V 2 A Output LEDs Number of LEDs 5 6 7 VF Forward Voltage of LED 3.2 3.5 4.0 V VOUT Output Voltage 16 21 28 V ILED LED Current 0.33 0.35 0.37 A IPP Required I Ripple Pout Output Power DIM_IN PWM Dimming OVP Output Over Voltage Protection 30 V FSW Switching Frequency 1 MHz eff Efficiency 80 % VDIODE Forward drop of schottky diode 0.5 V 40 0 mA 10.36 W 100 % System Table 1. Design example parameters January 2010 14 M9999-011510-A Micrel, Inc. MIC3223 Design Example In this example, we will be designing a boost LED driver operating off a 12V input. This design has been created to drive 6 LEDs at 350mA with a ripple of about 20%. We are designing for 80% efficiency at a switching frequency of 1MHz. Select RADJ Having chosen the LED drive current to be 350mA in this example, the current can be set by choosing the RADJ resistor from Equation 1: R ADJ = 0.2V = 0.57Ω 0.35A Use the next lowest standard value 0.56Ω. ILED = 0.36A The power dissipation in this resistor is: PRADJ = ILED 2 × R ADJ = 71mW Use a resistor rated at quarter watt or higher. Operating Duty Cycle The operating duty cycle can be calculated using Equation four provided below: (V − VIN + VDIODE ) D = OUT Eq. (4) VOUT + VDIODE VDIODE is the Vf of the output diode D1 in the Typical Application. It is recommended to use a schottky diode because it has a lower Vf than a junction diode. These can be calculated for the nominal (typical) operating conditions, but should also be understood for the minimum and maximum system conditions as listed below. Dnom = Dmax = Dmin = (VOUT(nom) − VIN(nom) + VDIODE ) VOUT(nom) + VDIODE (VOUT(max) − VIN(min) + VDIODE ) VOUT(max) + VDIODE (VOUT(min) − VIN(max) + VDIODE ) VOUT(min) + VDIODE (21 − 12 − 0.5) = 0.44 Dnom = Using Equation 5, the following values have been calculated: IIN_RMS(max) = IIN_RMS(nom ) = Eq (5) VOUT(max) × IOUT(max) eff × VIN(min) VOUT(nom) × IOUT(nom) eff × VIN(nom) VOUT(min) × IOUT(min) IIN_RMS(min) = eff × VIN(max) Eq. (6) Therefore Dnom = 44%, Dmax = 72% and Dmin = 15%. Inductor Selection First calculate the RMS input current (nominal, min and max) for the system given the operating conditions listed in the design example table. The minimum value of the RMS input current is necessary to ensure proper operation. January 2010 = 0.46A (RMS) L= VIN × D I ×F IN_PP SW Using the nominal values, we get: L= 12V × 0.44 0.3A × 1MHz = 18μH Select the next higher standard inductor value of 22µH. Going back and calculating the actual ripple current gives: IIN_PP(max) = VIN(min) × D max L × FSW = 8V × 0.72 = 0.26A PP 22 μH × 1MHz The average input current is different than the RMS input current because of the ripple current. If the ripple current is low, then the average input current nearly equals the RMS input current. In the case where the average input current is different than the RMS, equation 7 shows the following: Eq. (7) ( 21- 12 + 0.5) = 0.44 = 21+ 0.5 = 0.74A (RMS) IOUT is the same as ILED. Selecting the inductor current (peak-to-peak), IL_PP, to be between 20% to 50% of IIN_RMS(nom), in this case 40%, we obtain: IIN_PP(nom) = 0.4 × IIN_RMS(nom) = 0.4 × 0.74 = 0.30AP-P It can be difficult to find large inductor values with high saturation currents in a surface mount package. Due to this, the percentage of the ripple current may be limited by the available inductor. It is recommended to operate in the continuous conduction mode. The selection of L described here is for continuous conduction mode. IIN_AVE(max) = (IIN_RMS(max) )2 − 21 + 0.5 Dnom = 1.54A (RMS) IIN_AVE(max) = (1.54 )2 − (IIN_PP ) 2 12 (0.24) 2 ≈ 1.54 A 12 The Maximum Peak input current IL_PK can found using Equation 8: Eq. (8) IL_PK(max) = IIN_AVE(max) + 0.5 ×IL_PP(max) = 1.67A The saturation current (ISAT) at the highest operating temperature of the inductor must be rated higher than this. The power dissipated in the inductor is: 15 M9999-011510-A Micrel, Inc. MIC3223 Eq. (9) PINDUCTOR = IIN_RMS(max)2 × DCR A Coilcraft # MSS1260-223ML is used in this example. Its DCR is 52mΩ, ISAT =2.7A PINDUCTOR = 1.542 × 52 mΩ = 0.123W Output Capacitor In this LED driver application, the ILED ripple current is a more important factor when compared to that of the output ripple voltage (although the two are directly related). To find the COUT for a required ILED ripple use the following calculation: For an output ripple ILED(ripple) = 20ma Eq. (10) C OUT = ILED(nom) × D nom ILED(ripple) × (R ADJ + R LED_total ) × FSW Find the equivalent ac resistance RLED_ac from the datasheet of the LED. This is the inverse slope of the ILED vs. Vf curve i.e.: ΔVf ΔLED In this example use RLED_ac = 0.6Ω for each LED. If the LEDs are connected in series, multiply RLED_ac = 0.6Ω by the total number of LEDs. In this example of six LEDs, we obtain the following: RLED_total ≡ Rdynamic = 6 × 0.6Ω = 3.6Ω Eq. (12) RLED_ac = Eq. (11) C OUT = ILED(nom) × D nom ILED(ripple) × (R ADJ + R LED_total ) × FSW = 1.9 μF Use 2.2µF or higher. There is a trade off between the output ripple and the rising edge of the DIM_IN pulse. This is because between PWM dimming pulses, the converter stops pulsing and COUT will start to discharge. The amount that COUT will discharge depends on the time between PWM Dimming pluses. At the next DIM_IN pulse, COUT has to be charged up to the full output voltage VOUT before the desired LED current flows. Input Capacitor The input capacitor is shown in the Typical Application. For superior performance, ceramic capacitors should be used because of their low equivalent series resistance (ESR). The input capacitor CIN ripple current is equal to the ripple in the inductor. The ripple voltage across the input capacitor, CIN is the ESR of CIN times the inductor ripple. The input capacitor will also bypass the EMI generated by the converter as well as any voltage spikes generated by the inductance of the input line. For a required VIN(ripple): Eq. (13) January 2010 C IN = IIN_PP VIN(ripple) × FSW = (0.3A) = 0.75 μF 8 × 50mV × 1MHz This is the minimum value that should be used. To protect the IC from inductive spikes or any overshoot, a larger value of input capacitance may be required. Use 2.2µF or higher as a good safe min. Rectifier Diode Selection A schottky diode is best used here because of the lower forward voltage and the low reverse recovery time. The voltage stress on the diode is the max VOUT and therefore a diode with a higher rating than max VOUT should be used. An 80% de-rating is recommended here as well. Eq. (14) IDIODE(max) = IOUT(max) = 0.36A Since IIN_AVE(max) occurs when D is at a maximum. Eq. (15) PDIODE(max) ≈ VDIODE × IDIODE_(max) A SK35B is used in this example, it’s VDIODE is 0.5V PDIODE(max) ≈ 0.5V × 0.36A = 0.18W MIC3223 Power Losses To find the power losses in the MIC3223: There is about 6mA input from VIN into the VDD pin. The internal power switch has an RDSON of about 170mΩ at. PMIC3223 = VIN × 6mA + PwrFET Eq. (16) PwrFET = IFET_RMS(max)2 × Rds_on_@100° + VOUT(max) × IIN_AVE(max) × tsw × Fsw Rds_on_@100° ≈ 160mΩ tsw ≈ 30ns is the internal Power FET ON an OFF transition time. 2 ⎛ IL_PP 2 ISWRMS(max) = D⎜ IIN_AVE(max) + ⎜ 12 ⎝ ⎞ ⎟ = 1.3A ⎟ ⎠ PwrFET = 1.3A2 × 160mΩ + 28V × 1.54A × 30ns × 1MHz = 1.6W PMIC3223 = 8 × 6mA + 1.77W = 1.66W Snubber A snubber is a damping resistor in series with a DC blocking capacitor in parallel with the power switch (same as across the flyback diode because VOUT is an ac ground). When the power switch turns off, the drain to source capacitance and parasitic inductance will cause a high frequency ringing at the switch node. A snubber circuit as shown in the application schematic may be required if ringing is present at the switch node. A critically damped circuit at the switch node is where R equals the characteristic impedance of the switch node. 16 M9999-011510-A Micrel, Inc. MIC3223 Eq.(17) R snubber = Lparisitic Cds The explanation of the method to find the best R snubber is beyond the scope of this data sheet. Use Rsnubber = 2Ω, ½ watt and Csnubber = 470pf to 1000pf. The power dissipation in the Rsnubber is: Rsnubber = Csnubber × VOUT2 × FSW Psnubber = 470pF × 28V2 × 1MHz = 0.4W Figure 10. Simplified Control Loop Eq. (19) Where T(s) = Gea(s) × Gvc(s) × H(s) For a LED driver H(s) = Power Loss in the L 0.123 W Power Loss in the sckottky diode 0.2 W Psnubber 0.4 W MIC3223 Power Loss 1.66 W Total Losses 2.4W Efficiency 80% ⎛ ⎛ 1 Gea (s) = gm ⎜ Z O || ⎜ R comp + ⎜ ⎜ sCcomp ⎝ ⎝ G VC (s) = Eq. (18) R OVP_L Compensation Figure 9. Current Mode Loop Diagram Current mode control simplifies the compensation. In current mode, the complex poles created by the output L and C are reduced to a single pole. The explanation for this is beyond the scope of this datasheet, but it’s generally thought to be because the inductor becomes a constant current source and can’t act to change phase. From the small signal block diagram the loop transfer function is: Where VOUT Is the DC operating point of the converter. ILED Rdymanic is the ac load the converter sees. When the load on the converter is a string of LEDs, Rdymanic is the series sum of the RLED(ac) of each LED. RLED_total is usually between 0.1Ω to 1Ω per LED. It can be calculated from the slope of ILED vs. Vf plot of the LED. Ri = Ai × Rcs = 0.86Ω Ai = 114 and Rcs ≡ 7.5mΩ; are internal to the ic. The equation for Gvc(s) is theoretical and should give a good idea of where the poles and zeros are located. R OP = Eq.(20) shows that s = D'2 R dynamic → fRHPZ = D'2 R dynamic L 2πL is a RHP Zero. The loop bandwidth should be about 1/5 to 1/10 of the frequency of RHPZ to ensure stability. From Equation (20) it is shown that there is only the single pole. 1 1 → fpole = and a Zero s= R dynamic COUT 2πR dynamic COUT due to the ESR of the output capacitor. s= January 2010 VOUT (s) VCONTROL (s) ⎛ ⎞ sL ⎜1 − ⎟(1 + sC OUTRESR ) 2 ⎜ ⎟ ⎛ 1 ⎞⎛ D' R OP ⎞ ⎝ D' R dynamic ⎠ = ⎜ ⎟⎜ ⎟ ⎛ sR dynamic COUT ⎞ ⎝ Ri ⎠⎝ 2 ⎠ ⎟ ⎜1 + ⎟ ⎜ 2 ⎠ ⎝ Table 2 showing the Power losses in the Design Example. 100kΩ × 1.245 = 4.33kΩ = 30 − 1.245 ⎞⎞ ⎟⎟ ⎟⎟ ⎠⎠ Eq. (20) Table 2. Major Power Losses OVP - Over Voltage Protection Set OVP higher than the maximum output voltage by at least one Volt. To find the resistor divider values for OVP use equation 18 and set the OVP = 30V and ROVP_H = 100kΩ: R ADJ and R ADJ + R dynamic 17 1 1 → fESR = RESR COUT 2πRESR COUT M9999-011510-A Micrel, Inc. This greatly simplifies the compensation. One needs only to get a bode plot of the transfer function of the control to output Gvc(s) with a network analyzer and/or calculate it. From the bode plot find what the gain of R Gvc(s) is at f = HPZ . Next design the error amp gain 10 Gea(s) so the loop gain at the cross over frequency T(fco) is R 0 db where fco = HPZ or less. 10 MIC3223 The error amp is a gm type and the gain Gea(s) is ⎛ ⎛ 1 Gea (s) = gm ⎜ Z O || ⎜ R comp + ⎜ ⎜ sC comp ⎝ ⎝ Eq. (21) gm = ⎞⎞ ⎟⎟ ⎟⎟ ⎠⎠ 0.8mA and Zo = 1.2MΩ. V The zero is fzero = Error Amp f 1 R = co = HPZ . 2R compCcomp 10 100 Error Amp Gain and Phase 60 Gain GAIN (dB) / PHASE (°) 40 20 0 -20 Phase -40 -60 -80 1.E+02 1.E+03 1.E+04 1.E+05 1.E+06 FREQUENCY (Hz) Figure 11. Internal Error Amp and External Compensation Set the fco at the mid band where Gea(fco) = gm × Rcomp. At fzero × 10 the phase boost is near its maximum. Figure 12. Error Amp Transfer Function January 2010 18 M9999-011510-A Micrel, Inc. MIC3223 Other Applications Figure 13. MIC3223 Typical Application without External PWM Dimming Switch 2. Even though the RRC is very short (tens of nanoseconds) the peak currents are high (multiple amperes). These fast current spikes generate EMI (electromagnetic interference). The amount of RRC is related to the die size and internal capacitance of the diode. It is important not to oversize (i.e. not more than the usual de rating) the diode because the RRC will be needlessly higher. Example: If a 2A diode is needed do not use a higher current rated diode because the RRC will be needlessly higher. If a 25V diode is needed do not use a 100V etc. 3. The high RRC causes a voltage drop on the ground trace of the PCB and if the converter control IC is referenced to this voltage drop, the output regulation will suffer. 4. For good output regulation, it is important to connect the IC’s reference to the same point as the output capacitors to avoid the voltage drop caused by RRC. This is also called a star connection or single point grounding. 5. Feedback trace: The high impedance traces of the FB should be short. Audio noise Audio noise from the output capacitors may exits in a standard boost LED converter. The physical dimensions of ceramic capacitors change with the voltage applied to them. During PWM Dimming, the output capacitors in standard converters are subjected to fast voltage and current transients that may cause the output capacitors to oscillate at the PWM Dimming frequency. This is one reason users may want PWM dimming frequencies above the audio range. PCB Layout 1. All typologies of DC-to-DC converters have a Reverse Recovery Current (RRC) of the flyback or (freewheeling) diode. Even a Schottky diode, which is advertised as having zero RRC, it really is not zero. The RRC of the freewheeling diode in a boost converter is even greater than in the Buck converter. This is because the output voltage is higher than the input voltage and the diode has to charge up to –VOUT during each ontime pulse and then discharge to Vf during the off-time. January 2010 19 M9999-011510-A Micrel, Inc. MIC3223 Evaluation Board Schematic 37V Max 1A LED Driver January 2010 20 M9999-011510-A Micrel, Inc. MIC3223 Bill of Materials Item Part Number GRM319R61E475KA12D C1 C2 C3, C7 C4, C6 C5 C8 Manufacturer Description Qty (1) muRata C3216X7R1E475M TDK(2) 12063D475KAT2A AVX(3) GRM188R71C273KA01D muRata GRM188R60J106ME47D muRata C1608X5R0J106K TDK 08056D106MAT2A AVX 12105C475KAZ2A AVX GRM32ER71H475KA88L muRata GRM188R71C473KA01D muRata 0603YC473K4T2A AVX GRM188R72A102KA37D muRata SK35B L1 MSD1260-223ML-LD Coilcraft(6) R1, R3 CRCW0603100KFKEA R2 R4 1 Ceramic Capacitor, 0.027µF, 6.3V, Size 0603, X7R 1 Ceramic Capacitor, 10µF, 6.3V, Size 0603, X7R 2 Ceramic Capacitor, 4.7µF, 50V, Size 1210, X7R 2 Ceramic Capacitor, 0.047µF, 6.3V, Size 0603, X7R 1 Ceramic Capacitor, 1000pF, 100V Size 0603, X7R (4) D1 Ceramic Capacitor, 4.7µF, 25V, Size 1206, X7R Schottky Diode, 3A, 50V (SMB) 1 Inductor, 22µH, 5A 1 Vishay Dale(4) Resistor, 100k, 1%, Size 0603 2 CRCW0603549RFKEA Vishay Dale Resistor, 549Ω, 1%, Size 0603 1 CRCW06033K24FKEA Vishay Dale Resistor, 3.24k, 1%, Size 0603 1 R5 CRCW1206R560FKEA Vishay Dale Resistor, 0.56Ω, 1%, 1/2W, Size 1206 (for .35A LED current Change for different ILED) 1 R6 RMC 1/4 2 1% R Stackpole Electronics, Inc.(7) Resistor, 2Ω, 1%, 1/2W, Size 1210 1 Si2318DS Vishay Siliconix(4) N-Channel 40V MOSFET 1 High Power Boost LED Driver with Integrated FET 1 Q1 U1 MCC (8) AM2340N Analog Power MIC3223 Micrel, Inc.(9) Notes: 1. Murata: www.murata.com. 2. TDK: www.tdk.com. 3. AVX: www.avx.com. 4. Vishay: www.vishay.com. 5. Internacional Rectifier: www.ift.com. 6. Coilcraft: www.coilcraft.com 7. Stackpole Electronics, Inc.: www. 8. Analog Power: www.analogpowerinc.com 8. Micrel, Inc.: www.micrel.com. January 2010 21 M9999-011510-A Micrel, Inc. MIC3223 PCB Layout Recommendations Top Layer Bottom Layer January 2010 22 M9999-011510-A Micrel, Inc. MIC3223 Package Information 16-Pin ePad TSSOP (TSE) January 2010 23 M9999-011510-A Micrel, Inc. MIC3223 Recommended Land Pattern MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http://www.micrel.com The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. © 2009 Micrel, Incorporated. January 2010 24 M9999-011510-A