MMBTA55 PZTA55 C C E C B TO-92 SOT-23 E B B SOT-223 Mark: 2H E C PNP General Purpose Amplifier This device is designed for general purpose amplifier applications at collector currents to 300 mA. Sourced from Process 73. See MPSA56 for characteristics. Absolute Maximum Ratings* Symbol TA = 25°C unless otherwise noted Value Units VCES Collector-Emitter Voltage Parameter 60 V VCBO Collector-Base Voltage 60 V VEBO Emitter-Base Voltage 4.0 V IC Collector Current - Continuous 500 mA TJ, Tstg Operating and Storage Junction Temperature Range -55 to +150 °C *These ratings are limiting values above which the serviceability of any semiconductor device may be impaired. NOTES: 1) These ratings are based on a maximum junction temperature of 150 degrees C. 2) These are steady state limits. The factory should be consulted on applications involving pulsed or low duty cycle operations. Thermal Characteristics Symbol PD TA = 25°C unless otherwise noted Characteristic RθJC Total Device Dissipation Derate above 25°C Thermal Resistance, Junction to Case RθJA Thermal Resistance, Junction to Ambient Max Units MPSA55 625 5.0 83.3 *MMBTA55 350 2.8 **PZTA55 1,000 8.0 200 357 125 mW mW/°C °C/W °C/W *Device mounted on FR-4 PCB 1.6" X 1.6" X 0.06." **Device mounted on FR-4 PCB 36 mm X 18 mm X 1.5 mm; mounting pad for the collector lead min. 6 cm2. ã 1997 Fairchild Semiconductor Corporation MPSA55/MMBTA55/PZTA55, Rev A MPSA55 / MMBTA55 / PZTA55 MPSA55 (continued) Electrical Characteristics Symbol TA = 25°C unless otherwise noted Parameter Test Conditions Min Max Units OFF CHARACTERISTICS V (BR)CEO IC = 1.0 mA, IB = 0 V (BR)CBO Collector-Emitter Breakdown Voltage* Collector-Base Breakdown Voltage 60 V V (BR)EBO Emitter-Base Breakdown Voltage IC = 100 µA, IE = 0 60 V 4.0 Collector-Cutoff Current IE = 100 µA, I C = 0 V CE = 60 V, IB = 0 ICEO ICBO Collector-Cutoff Current V CB = 60 V, IE = 0 V 0.1 µA 0.1 µA ON CHARACTERISTICS hFE DC Current Gain VCE(sat) Collector-Emitter Saturation Voltage IC = 10 mA, VCE = 1.0 V IC = 100 mA, VCE = 1.0 V IC = 100 mA, IB = 10 mA VBE(on) Base-Emitter On Voltage IC = 100 mA, VCE = 1.0 V 100 100 0.25 V 1.2 V SMALL SIGNAL CHARACTERISTICS fT Current Gain - Bandwidth Product *Pulse Test: Pulse Width £ 300 ms, Duty Cycle £ 2.0% IC = 100 mA, VCE = 1.0 V, f = 100 MHz 50 MHz MPSA55 / MMBTA55 / PZTA55 PNP General Purpose Amplifier TO-92 Tape and Reel Data TO-92 Packaging Configuration: Figure 1.0 Packaging Description: TO-92 parts are shipped normally in tape. These reeled parts in standard option are shipped with 2,000 units per 14” or 355.6cm diameter reel. This and some other options are further described in the Packaging Information table.These full reels are individually barcode labeled and placed inside a standard intermediate box (illustrated in figure 1.0) made of recyclable corrugated brown paper. One box contains one reel maximum. And these boxes are placed inside a barcode labeled shipping box which comes in different sizes depending on the number of parts shipped. 1 Reel per Inner box FKS Label 395mm x 375mm x 56mm Inner box(2,000cap) FKS Label TO-92 Packaging Configuration: Figure 2.0 Inner Box Bar Code Label Sample TO-92 Packaging Information Standard Standard Standard (no flow code) (no flow code) (no flow code) TNR AMMO BULK Packaging Option Packaging type Qty per Reel/Tube/ Bag Reel Size Inner Box Dimension (mm) Max qty per Box 2,000 MBB : NOR P/U : 660 S/T : LOGO I/B: LOGO HIC : 0 P/T:O MIX: X DVC: 1,000 14” Dia - - 395x375x56 328x162x43 237x167x96 2,000 2,000 10,000 00 / 03 / 17 06:30 P ETC: KA7812-AE 0101 LOT: TKLEE777 Q’TY: 1000 W/W: 0103 OPTION: 20000025 420mm x 420mm x 320mm Outer box(10,000cap) Outer Box Dimension (mm) 420x420x320 525x360x265 525x360x265 Max qty per Box 10,000 30,000 100,000 Weight per unit (gm) 0.2080 0.2080 0.2080 Outer Box Bar Code Label Sample 00 / 03 / 17 07:30 DVC: LOT: Q’TY: Note/Comments TO-92 AMMO Packaging Configuration: Figure 3.0 KA7812-AE IMSYS777 12000 IM 88706892 FKS Label 01 7103 A710103105 525mm x 360m x 265mm Outer box (30,000cap) 15 Ammo boxes per Outer Box 328mm x 162mm x 43mm Inner box (2,000cap) FKS Label FKS Label TO-92 Bulk Packing Configuration: Figure 4.0 FKS Label 10 Vinyl bags per Inner box 1,000 units per Bulk Vinyl bag ©2001 Fairchild Semiconductor Corporation 237mm x 167mm x 96mm Bulk Inner box(10,000cap) 525mm x 360mm x 265mm Outer box(100,000cap) FKS Label October 2001, Rev. A TO-92 Tape and Reel Data, continued TO-92 Reeling Style Configuration: Figure 5.0 Standard Machine Option TO-92 Radial Ammo Packaging Configuration: Figure 6.0 Standard FIRST WIRE OFF IS EMITTER ADHESIVE TAPE IS ON THE TOP SIDE FLAT OF TRANSISTOR IS ON BOTTOM FIRST WIRE OFF IS COLLECTOR ADHESIVE TAPE IS ON BOTTOM SIDE FLAT OF TRANSISTOR IS ON TOP Machine Option FIRST WIRE OFF IS COLLECTOR ADHESIVE TAPE IS ON THE TOP SIDE FLAT OF TRANSISTOR IS ON TOP FIRST WIRE OFF IS EMITTER ADHESIVE TAPE IS ON BOTTOM SIDE FLAT OF TRANSISTOR IS ON BOTTOM October 2001, Rev. A TO-92 Tape and Reel Data, continued TO-92 Tape and Reel Taping Dimension Configuration: Figure 7.0 T A1 jh P A H1 W2 d H HO J1 WO W1 W P1 F1 t F2 DO P2 PO User Direction of Feed TO-92 Reel Configuration: Figure 8.0 ITEM DESCRIPTION SYMBOL DIMENSION Body Width A1 4.58 (+ 0.25, - 0.15) Body Height A 4.58 (+/- 0.20) Body Thickness T 3.86 (max) Lead-Wire Diameter d 0.46 (+/- 0.05) Pitch of Component P 12.7 (+/- 0.50) Feed Hole Pitch P0 12.7 (+/ -0.20) Hole Center to Component Center P2 6.35 (+/- 0.50) Lead to Lead Distance F1,F2 2.50 (+ 0.3, - 0.10) Component Alignment F-R jh 0.00 (+/- 1.00) Tape Width W 18.00 (+ 1.00, - 0.50) Hole-Down Tape Width W0 6.00 (+/- 0.50) Hole Position W1 9.00 (+/ -0.50) Hole-Down Tape Position W2 1.00 (max) Height of Component From Tape Center H 19.50 (+/- 1.00) Lead-Wire Clinch Height H0 16.00 (+/- 0.50) Component Height H1 27.0 (max) Lead-Wire (Tape Portion) J1 2.50 (min) Feed Hole Diameter D0 4.00 (+/- 0.20) Total Tape Thickness t 0.65 (+/- 0.20) Position of Hole P1 3.85 (+/- 0.50) REMARK In Case of Reel Package +/- 1.00 F1-F2= +/- 0.30 H + A <= H1 Note : All dimensions are in millimeters. ELECTROSTATIC SENSITIVE DEV ICES D4 D1 D2 ITEM DESCRIPTION SYSMBOL MINIMUM MAXIMUM Reel Diameter D1 13.975 14.025 Arbor Hole Diameter (Standard) D2 1.160 1.200 D2 0.650 0.700 Core Diameter D3 3.100 3.300 Hub Recess Inner Diameter D4 2.700 3.100 Hub Recess Depth W1 0.370 0.570 Flange to Flange Inner Width W2 1.630 Hub to Hub Center Width W3 (Small Hole) FKS Label W1 W2 1.690 2.090 W3 Note: All dimensions are inches October 2001, Rev. A TO-92 Package Dimensions TO-92 (FS PKG CODE AM) +0.25 4.58 ±0.20 4.58 –0.15 14.47 ±0.40 0.46 ±0.10 1.27TYP [1.27 ±0.20] 1.27TYP [1.27 ±0.20] +0.10 0.38 –0.05 (0.25) +0.10 0.38 –0.05 1.02 ±0.10 3.86MAX 3.60 ±0.20 (R2.29) Dimensions in Millimeters August 1999, Rev B SOT-23 Tape and Reel Data SOT-23 Packaging Configuration: Figure 1.0 Packaging Description: SOT-23 parts are shipped in tape. The carrier tape is made from a dissipative (carbon filled) polycarbonate resin. The cover tape is a multilayer film (Heat Activated Adhesive in nature) primarily composed of polyester film, adhesive layer, sealant, and anti-static sprayed agent. These reeled parts in standard option are shipped with 3,000 units per 7” or 17.7cm diameter reel. The reels are clear in color and is made of polystyrene plastic (anti-static coated). This and some other options are further described in the Packaging Information table. These full reels are individually barcode labeled and placed inside a standard intermediate box (illustrated in figure 1.0) made of recyclable corrugated brown paper. One box contains five reels maximum. And these boxes are placed inside a barcode labeled shipping box which comes in different sizes depending on the number of parts shipped. Antistatic Cover Tape Static Dissipative Embossed Carrier Tape FKS Label 7H 7H 7H 7H Pin 1 SOT-23 Unit Orientation SOT-23 Packaging Information Standard Packaging Option Packaging type TNR Qty per Reel/Tube/Bag 3,000 Reel Size 5 Reels per box 7” Dia Inner Box Dimension (mm) 188x181x69 15,000 Max qty per Box Outer Box Dimension (mm) 420x420x320 Max qty per Box 180,000 Weight per unit (gm) 0.0084 Weight per Reel (kg) - FKS Label 188mm x 181mm x 69mm Inner box(15,000cap) Note/Comments Inner Box Barcode Label Sample MBB : NOR P/U : 660 S/T : LOGO I/B: LOGO HIC : 0 P/T:O MIX: X DVC: P ETC: Outer Box Barcode Label Sample 00 / 03 / 17 06:30 KA7812-AE LOT: TKLEE777 Q’TY: 1000 W/W: 0103 OPTION: 20000025 00 / 03 / 17 07:30 DVC: LOT: Q’TY: 01 KA7812-AE IMSYS777 12000 A710103105 IM 88706892 01 7103 FKS Label SOT-23 Tape Leader and Trailer Configuration: Figure 2.0 420m x 420mm x 320mm Outer box(180,000cap) Carrier Tape Cover Tape Trailer Tape 640mm minimum or 80 empty pockets ©2001 Fairchild Semiconductor Corporation Components Leader Tape 1680mm minimum or 210 empty pockets October 2001, Rev. A SOT-23 Tape and Reel Data, continued SOT-23 Embossed Carrier Tape Configuration: Figure 3.0 P0 P2 D0 D1 T E1 W F E2 Wc B0 Tc A0 P1 K0 User Direction of Feed Notes: A0, B0, and K0 dimensions are determined with respect to the EIA/Jedec RS-481 rotational and lateral movement requirements (see sketches A, B, and C). 0.5mm maximum 20 deg maximum Typical component cavity center line B0 0.5mm maximum 20 deg maximum component rotation Typical component center line Sketch A (Side or Front Sectional View) A0 Component Rotation Sketch C (Top View) Component lateral movement Sketch B (Top View) Component Rotation SOT-23 Reel Configuration: Figure 4.0 W1 Measured at Hub B Min Dim C Dim N Dim A max Dim D min DETAIL AA See detail AA W3 7” Diameter Option W2 max Measured at Hub Dimensions are in inches and millimeters Tape Size 8.0mm Reel Option 7” Dia Dim A Dim B 7.00 177.8 0.059 1.5 Dim C 0.512 +0.020/-0.008 13 +0.5/-0.2 Dim D 0.795 20.2 Dim N 2.165 55 Dim W1 0.331 +0.059/-0.000 8.4 +1.5/0 Dim W2 0.567 14.4 Dim W3 (LSL-USL) 0.311 – 0.429 7.9 – 10.9 October 2001, Rev. A SOT-23 Package Dimensions 1.30 ±0.10 0.40 ±0.03 2.40 ±0.10 0.45~0.60 0.20 MIN SOT-23 (FS PKG CODE AU) 0.03~0.10 0.38 REF 0.40 ±0.03 +0.05 0.12 –0.023 0.96~1.14 0.97REF 2.90 ±0.10 0.95 ±0.03 0.95 ±0.03 1.90 ±0.03 0.508REF Dimensions in Millimeters August 1999, Rev B SOT-223 Tape and Reel Data SOT-223 Packaging Configuration: Figure 1.0 Packaging Description: SOT-223 parts are shipped in tape. The carrier tape is made from a dissipative (carbon filled) polycarbonate resin. The cover tape is a multilayer film (Heat Activated Adhesive in nature) primarily composed of polyester film, adhesive layer, sealant, and anti-static sprayed agent. These reeled parts in standard option are shipped with 4000 units per 13” or 330cm diameter reel. The reels are dark blue or black in color and is made of polystyrene plastic (anti-static coated). This and some other options are further described in the Packaging Information table.These full reels are individually barcode labeled and placed inside a standard intermediate box (illustrated in figure 1.0) made of recyclable corrugated brown paper. One box contains four reels maximum. And these boxes are placed inside a barcode labeled shipping box which comes in different sizes depending on the number of parts shipped. Antistatic Cover Tape Static Dissipative Embossed Carrier Tape FKS Label F T0133 FQT13N60 F T0133 FQT13N60 F T0133 FQT13N60 F T0133 FQT13N60 SOT-223 Unit Orientation 4 Reels per box SOT-223 Packaging Information Standard Packaging Option Packaging type TNR Qty per Reel/Tube/Bag 4,000 13” Dia Reel Size Inner Box Dimension (mm) 339x352x68 Max qty per Box 16,000 Outer Box Dimension (mm) FKS Label 420x420x320 Max qty per Box 64,000 Weight per unit (gm) 0.1118 Weight per Reel(kg) - 339mm x 352mm x 68mm Inner box(16,000cap) Note/Comments Inner Box Barcode Label Sample MBB : NOR P/U : 660 S/T : LOGO I/B: LOGO HIC : 0 P/T:O MIX: X DVC: P ETC: Outer Box Barcode Label Sample 00 / 03 / 17 06:30 KA7812-AE LOT: TKLEE777 Q’TY: 1000 W/W: 0103 OPTION: 20000025 00 / 03 / 17 07:30 DVC: LOT: Q’TY: 01 KA7812-AE IMSYS777 12000 A710103105 IM 88706892 01 7103 FKS Label 420mm x 420mm x 320mm Outer box(64,000cap) SOT-223 Tape Leader and Trailer Configuration: Figure 2.0 Carrier Tape Cover Tape Trailer Tape 360mm minimum or 45 empty pockets ©2001 Fairchild Semiconductor Corporation Components Leader Tape 1520mm minimum or 190 empty pockets October 2001, Rev. A SOT-223 Tape and Reel Data, continued SOT-223 Embossed Carrier Tape Configuration: Figure 3.0 P0 D0 T E1 F K0 Wc W E2 B0 Tc A0 D1 P1 User Direction of Feed Dimensions are in millimeter Pkg type A0 B0 W D0 D1 E1 E2 F P1 P0 K0 T Wc Tc SOT-223 (12mm) 6.83 +/-0.10 7.42 +/-0.10 12.0 +/-0.2 1.55 +/-0.05 1.50 +/-0.10 1.75 +/-0.10 10.25 min 5.50 +/-0.05 8.0 +/-0.1 4.0 +/-0.1 1.80 +/-0.10 0.30 +/-0.05 9.50 +/-0.1 0.10 max Notes: A0, B0, and K0 dimensions are determined with respect to the EIA/Jedec RS-481 rotational and lateral movement requirements (see sketches A, B, and C). 20 deg maximum 0.5mm maximum Typical component cavity center line B0 0.5mm maximum 20 deg maximum component rotation Typical component center line Sketch A (Side or Front Sectional View) A0 Component Rotation Sketch C (Top View) Component lateral movement Sketch B (Top View) Component Rotation SOT-223 Reel Configuration: Figure 4.0 W1 Measured at Hub B Min Dim C Dim A max Dim D min Dim N DETAIL AA See detail AA W3 13” Diameter Option W2 max Measured at Hub Dimensions are in inches and millimeters Tape Size 12.0mm Reel Option 13” Dia Dim A Dim B 13.00 330 0.059 1.5 Dim C 0.512 +0.020/-0.008 13 +0.5/-0.2 Dim D 0.795 20.2 Dim N 4.00 100 Dim W1 0.488 +0.078/-0.000 12.4 +2/0 Dim W2 0.724 18.4 Dim W3 (LSL-USL) 0.468 – 0.606 11.9 – 15.4 October 2001, Rev. A SOT-223 Package Dimensions 3.00 ±0.10 4.60 ±0.25 6.50 ±0.20 (0.89) (0.95) (0.46) 1.60 ±0.20 2.30 TYP 0.70 ±0.10 (0.95) 10 +0.10 0.25 –0.05 0°~ 7.00 ±0.30 (0.60) +0.04 0.06 –0.02 (0.60) 3.50 ±0.20 1.75 ±0.20 MAX1.80 0.65 ±0.20 0.08MAX SOT-223 (FS PKG CODE AV) ° Dimensions in Millimeters August 1999, Rev B TRADEMARKS The following are registered and unregistered trademarks Fairchild Semiconductor owns or is authorized to use and is not intended to be an exhaustive list of all such trademarks. ACEx™ Bottomless™ CoolFET™ CROSSVOLT™ DenseTrench™ DOME™ EcoSPARK™ E2CMOSTM EnSignaTM FACT™ FACT Quiet Series™ FAST FASTr™ FRFET™ GlobalOptoisolator™ GTO™ HiSeC™ ISOPLANAR™ LittleFET™ MicroFET™ MicroPak™ MICROWIRE™ OPTOLOGIC™ OPTOPLANAR™ PACMAN™ POP™ Power247™ PowerTrench QFET™ QS™ QT Optoelectronics™ Quiet Series™ SILENT SWITCHER SMART START™ STAR*POWER™ Stealth™ SuperSOT™-3 SuperSOT™-6 SuperSOT™-8 SyncFET™ TinyLogic™ TruTranslation™ UHC™ UltraFET VCX™ STAR*POWER is used under license DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or 2. A critical component is any component of a life systems which, (a) are intended for surgical implant into support device or system whose failure to perform can the body, or (b) support or sustain life, or (c) whose be reasonably expected to cause the failure of the life failure to perform when properly used in accordance support device or system, or to affect its safety or with instructions for use provided in the labeling, can be effectiveness. reasonably expected to result in significant injury to the user. PRODUCT STATUS DEFINITIONS Definition of Terms Datasheet Identification Product Status Definition Advance Information Formative or In Design This datasheet contains the design specifications for product development. Specifications may change in any manner without notice. Preliminary First Production This datasheet contains preliminary data, and supplementary data will be published at a later date. Fairchild Semiconductor reserves the right to make changes at any time without notice in order to improve design. No Identification Needed Full Production This datasheet contains final specifications. Fairchild Semiconductor reserves the right to make changes at any time without notice in order to improve design. Obsolete Not In Production This datasheet contains specifications on a product that has been discontinued by Fairchild semiconductor. The datasheet is printed for reference information only. Rev. H4