Process Sealed Ultra-Miniature Rockers Series G Distinctive Characteristics Ultra-miniature size allows high density mounting, and extremely light weight of 0.25 gram makes these switches ideal for handheld equipment. Totally sealed body construction prevents contact contamination and allows time-and money-saving automated soldering and cleaning. Award-winning STC contact mechanism with benefits unavailable in conventional mechanisms: smoother, positive detent actuation, increased contact stability and unparalleled logic-level reliability. (Additional STC details in Terms & Acronyms; see Supplement section.) .100” x .100” (2.54mm x 2.54mm) terminal spacing conforms to standard PC board grid spacing. Round terminals facilitate easier through-hole mounting on PC boards. Matching indicators available and shown at the end of Section M. Actual Size NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Process Sealed Ultra-Miniature Rockers Series G General Specifications Electrical Capacity (Resistive Load) Logic Level: Other Ratings Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Nominal Operating Force: Angle of Throw: Materials & Finishes Actuator: Case: Sealing Rings: Movable Contact: Stationary Contacts: Base: Terminals: Environmental Data Operating Temperature Range: Humidity: Vibration: Shock: Installation Cap Installation Force: PCB Processing Soldering: Cleaning: 0.4VA maximum @ 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V) Note: Find additional explanation of operating range in Supplement section. 80 milliohms maximum 500 megohms minimum @ 500V DC 500V AC minimum for 1 minute minimum 100,000 operations minimum for On-None-On & On-Off-On 50,000 operations minimum for other circuits 100,000 operations minimum for On-None-On & On-Off-On 50,000 operations minimum for other circuits .81N for momentary & 1.06N for maintained 28° Glass fiber reinforced polyamide Glass fiber reinforced polyamide Nitrile butadiene rubber Phosphor bronze with gold plating Phosphor bronze with gold plating Glass fiber reinforced polyamide Phosphor bronze with gold plating –25°C through +85°C (–13°F through +185°F) 90 ~ 95% humidity for 96 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) 39.1N (8.8 lbf) maximum downward force on actuator Wave Soldering Recommended: See Profile A in Supplement section. Manual Soldering: See Profile A in Supplement section. Automated cleaning. See Cleaning specifications in Supplement section. Standards & Certifications UL Recognition or CSA Certification: The G Series rockers have not been tested for UL recognition or CSA certification. These switches are designed for use in a low-voltage, low-current, logic-level circuit. When used as intended in a logic-level circuit, the results do not produce hazardous energy. NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Series G Process Sealed Ultra-Miniature Rockers TYPICAL SWITCH ORDERING EXAMPLE 2 G 2 K Y P A CAP COLORS POLES 1 SPDT 2 DPDT PC TERMINALS ACTUATOR K P Snap Top ROCKER CAP Y Straight Rocker A Black B White C Red CIRCUITS 2 ON NONE ON 3 ON OFF ON DESCRIPTION FOR TYPICAL ORDERING EXAMPLE 5 ON NONE (ON) G22KP-YA 8 (ON) OFF (ON) 9 ON OFF (ON) Snap Top with Black Rocker ( ) = Momentary DPDT ON-NONE-ON Circuit Straight PC Terminals POLES & CIRCUITS Rocker Position ( ) = Momentary Up Center Down Connected Terminals Up Center Throw & Schematics Down Note: Pole Model SP G12 G13 G15 G18 G19 ON ON ON (ON) ON NONE OFF NONE OFF OFF ON ON (ON) (ON) (ON) 5-6 OPEN 5-4 SPDT DP G22 G23 G25 G28 G29 ON ON ON (ON) ON NONE OFF NONE OFF OFF ON ON (ON) (ON) (ON) 5-6 2-3 OPEN 5-4 2-1 DPDT Terminal numbers are not actually on the switch. 5 (COM) 4 5 4 6 (COM) 6 2 1 NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 3 03-07 Process Sealed Ultra-Miniature Rockers Series G ACTUATOR K 28° Snap Top for Rocker (1.7) Dia .067 (2.3) .090 (3.8) .150 (4.0) .157 PC TERMINALS P (2.54) Typ .100 (0.4) Dia Typ .016 Straight (7.0) .276 (2.54) Typ .100 (2.6) .102 (4.5) .177 ROCKER CAP & COLORS Y (13.4) .528 (10.0) .394 28° AT4062 Rocker (6.2) .244 (11.25) .443 Material: Polyamide Finish: Matte (14.0) .551 Colors Available: A, B, C (11.5) .453 Actual Size Color Codes: A Black B C White Red TYPICAL SWITCH DIMENSIONS Straight PC Single & Double Pole (11.5) .452 (4.0) Dia .156 (2.54) .100 4 P/N This Side (0.4) Dia Typ .016 (2.54) Typ .100 5 6 28° (6.2) .244 G23KP-YA (3.8) .150 (14.0) .551 (1.6) .063 (7.0) .276 1 4 2 5 3 6 (7.0) .276 (0.6) Dia Typ .024 (2.54) .100 (2.54) Typ .100 (2.54) .100 (2.6) .102 (4.5) .177 4 1 5 2 6 3 (2.54) Typ .100 (0.6) Dia Typ .024 On single pole models positions 1 & 3 are support pins. NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07