Internationally Approved Pushbuttons Series JP Distinctive Characteristics Industry’s first molded pushbutton with TV rating. Designed to handle large inrush current. JPM models certified for TV-5 rating and JPL models for TV-8 rating. Prominent external insulating barriers increase insulation resistance and dielectric strength. Constructed for dust resistance with interior seal of polyphenylene sulfide (PPS) between actuator and contact area. Specially designed to break light contact welds. Snap-action contact mechanism. Terminals are molded in and epoxy sealed to lock out flux, dust, and other contaminants. Outer case of heat resistant resin meet UL’s 94V-0 flammability standard. Actual Size JPM NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Internationally Approved Pushbuttons Series JP General Specifications Electrical Capacity (Resistive Load) Power Level: Other Ratings Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Nominal Operating Force: Contact Timing: Latchdown: Travel: Materials & Finishes Housing/Frame & Barrier: Interior Seal: Case/Base: Environmental Data Operating Temp Range: Humidity: Vibration: Shock: Process Seal: Installation Soldering Time & Temp: Standards & Certifications Flammability Standards: TV Ratings for UL & CSA: UL File No. WOYR2.E44145 C-UL File No. WOYR8.E44145 UL Recognized: C-UL Certified: R V D E VDE Approved: 10A @ 125/250V AC for JPM models & 16A @ 125/250V AC for JPL models 20 milliohms maximum 1,000 megohms minimum @ 500V DC 2,000V AC minimum between contacts for 1 minute minimum; 4,000V AC minimum between contacts & case for 1 minute minimum 25,000 operations minimum 25,000 operations minimum JPM Single Pole 3.53N & Double Pole 6.47N JPL Single Pole 4.51N & Double Pole 9.02 N Nonshorting (break before make) Normal position - flush with barrier; latchdown position - .079” (2.0mm) below normal Pretravel .059” (1.5mm); Overtravel .071” (1.8mm); Total Travel .130” (3.3mm) Polyamide (UL94V-0) Polyphenylene sulfide (UL94V-0) Melamine (UL94V-0) Movable Contacts: Stationary Contacts: Terminals: Silver alloy Silver alloy Brass with silver plating –10°C through +70°C (+14°F through +158°F) 90 ~ 95% humidity for 96 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Dust resistant inner seal Manual Soldering: See Profile A in Supplement section. UL94V-0 for housing/frame, barrier, interior seal, & case/base JPM (TV-5) Overload Test @ 125V AC for 50 operations: Steady State Current (rms) 7.5A; Minimum Inrush Current (peak) 111A JPM (TV-5) Endurance Test @ 125V AC for 25,000 operations: Steady State Current (rms) 5A; Minimum Inrush Current (peak) 78A JPL (TV-8) Overload Test @ 125V AC for 50 operations: Steady State Current (rms) 12A; Minimum Inrush Current (peak) 163A JPL (TV-8) Endurance Test @ 125V AC for 25,000 operations: Steady State Current (rms) 8A; Minimum Inrush Current (peak) 117A All JPM models certified at 10A @ 125V AC, TV5 & JPL models at 16A @ 125V AC, TV8; add “/U” after part number to request marking on case; C-UL File No. WOYR2.E44145. All JPM models certified at 10A @ 125V AC, TV5 & JPL models at 16A @ 125V AC, TV8; add “/C-UL” after part number to request marking on case; C-UL File No. WOYR8.E44145. All JPM models approved at steady state 5A, inrush 80A, resistive 10A, & motor load 6A all at 250V AC; add “/V” after part number to request marking on case; VDE License No. 113494. All JPL models approved at steady state 8A, inrush 128A, resistive 16A, & motor load 8A all at 250V AC; add “/V” after part number to request marking on case; VDE License No. 097579. NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Internationally Approved Pushbuttons Series JP TYPICAL SWITCH ORDERING EXAMPLE JP M 2 6 H B RATINGS M TV-5 Rated 10A @ 125/250V AC L TV-8 Rated 16A @ 125/250V AC ACTUATORS SPST 2 DPST Flat Cap w/Barrier Flange P Plunger w/Flat Flange; cap not supplied w/plunger CIRCUIT POLES 1 B 6 OFF CAP COLORS ON (Alternate Action with Latchdown) A Black B Ivory C Red H Gray DESCRIPTION FOR TYPICAL ORDERING EXAMPLE JPM26B-H Gray Flat Cap with Barrier Flange TV-5 Rated 10A @ 125/250V AC DPST OFF-ON Circuit IMPORTANT: Specific models & ratings for international approvals noted on General Specifications page. NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Internationally Approved Pushbuttons Series JP RATINGS M TV-5 Rated Power Level 10A @ 125/250V AC L TV-8 Rated Power Level 16A @ 125/250V AC Note: See General Specifications page to find complete explanation of TV ratings. POLES & CIRCUIT Plunger Position Pole Connected Terminals Normal Down Normal Down OFF ON OPEN 1-1a SPST OFF ON OPEN 1-1a 2-2a DPST Model JPM16 SP Note: Terminal numbers are actually on the switch. 1 (COM) JPL16 1a 1 JPM26 DP Throw & Schematics JPL26 (COM) 2 1a 2a ACTUATORS B Flat Cap with Barrier Flange P Plunger with Flat Flange The barrier is an integral part of the switch. This housing is black, molded polyamide matte finish material. The flange is an integral part of the switch. This housing is black, molded polyamide matte finish material. Cap details below. No cap supplied. CAP COLORS AT3021 Flat Cap for Actuator Type B with Barrier Flange (18.0) .709 (22.0) .866 Cap Material: Polyphenylene Oxide The cap is flush with the barrier in normal position and .079” (2.0mm) below that in latchdown position. (6.8) .268 Finish: Matte Cap Colors Available: A Black B Ivory C Red H The latchdown feature on this alternate action device provides visible, audible, and tactile feedback. This design gives smooth, responsive operation. Gray NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Series JP Internationally Approved Pushbuttons PANEL CUTOUT & TERMINALS JPM & JPL Solder Lug/ .187”(4.75mm) Quick Connect Terminals Panel Thickness Range applies to both JPM & JPL models. This switch assembly, when used with connectors, is not CSA approved. (28.0) 1.102 .039” ~ .157” (1.0mm ~ 4.0mm) Epoxy Seal (7.2) (4.2) .283 (1.5) R .165 .059 (0.65) R (3.2) .026 .126 (4.75) .187 Thk = (0.5) .020 (21.2) .835 TYPICAL SWITCH DIMENSIONS B Flat Cap with Barrier Flange JPM & JPL Single & Double Pole Part No. (0.8) Typ .031 (20.8) .819 (9.4) .370 (22.0) .866 (26.6) 1.047 COM 2a 1a 2 1 (31.0) 1.220 (0.5) .020 (18.0) .709 (24.0) .945 (4.5) .177 (2.5) .098 (26.0) 1.024 Latchdown Position (1.5) .059 JPM26B-H P (4.75) Typ .187 (10.4) .409 (21.2) .835 (7.2) .283 Single pole model does not have terminals 2 & 2a. Plunger with Flat Flange JPM & JPL Single & Double Pole Part No. (2.0) .079 (3.3) Sq .130 (22.2) .874 (2.5) Sq .098 (1.0) .039 (2.5) .098 (18.3) .720 (24.0) .945 (20.8) .819 (0.8) Typ .031 (1.0) .039 (9.4) .370 (26.6) 1.047 COM 2a 1a 2 1 (31.0) 1.220 (0.5) .020 (8.5) .335 (6.5) .256 (16.0) .630 (2.0) .079 (26.0) 1.024 (1.5) .059 (7.2) .283 (10.4) .409 (21.2) .835 (4.75) Typ .187 Latchdown Position JPL16P Single pole model does not have terminals 2 & 2a. NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07