Toggles Series JP General Specifications Rockers Pushbuttons Programmable Illuminated PB Keylocks Rotaries Slides Tactiles Tilt Touch Indicators Accessories Supplement Internationally Approved Pushbuttons Electrical Capacity (Resistive Load) C Power Level: 10A @ 125/250V AC for JPM models & 16A @ 125/250V AC for JPL models Other Ratings Contact Resistance: 20 milliohms maximum Insulation Resistance: 1,000 megohms minimum @ 500V DC Dielectric Strength: 2,000V AC minimum between contacts for 1 minute minimum; 4,000V AC minimum between contacts & case for 1 minute minimum Mechanical Life: 25,000 operations minimum Electrical Life: 25,000 operations minimum Nominal Operating Force: JPM Single Pole 3.53N & Double Pole 6.47N JPL Single Pole 4.51N & Double Pole 9.02 N Contact Timing: Nonshorting (break before make) Latchdown: Normal position - flush with barrier; latchdown position - .079” (2.0mm) below normal Travel: Pretravel .059” (1.5mm); Overtravel .071” (1.8mm); Total Travel .130” (3.3mm) Materials & Finishes Housing/Frame & Barrier: Interior Seal: Case/Base: Environmental Data Operating Temp Range: Humidity: Vibration: Shock: Process Seal: Installation Soldering Time & Temp: Polyamide (UL94V-0) Polyphenylene sulfide (UL94V-0) Melamine (UL94V-0) Movable Contacts: Stationary Contacts: Terminals: Silver alloy Silver alloy Brass with silver plating –10°C through +70°C (+14°F through +158°F) 90 ~ 95% humidity for 96 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Dust resistant inner seal Manual Soldering: See Profile A in Supplement section. Standards & Certifications Flammability Standards: UL94V-0 for housing/frame, barrier, interior seal, & case/base TV Ratings for UL: JPM (TV-5) Overload Test @ 125V AC for 50 operations: Steady State Current (rms) 7.5A; Minimum Inrush Current (peak) 111A JPM (TV-5) Endurance Test @ 125V AC for 25,000 operations: Steady State Current (rms) 5A; Minimum Inrush Current (peak) 78A JPL (TV-8) Overload Test @ 125V AC for 50 operations: Steady State Current (rms) 12A; Minimum Inrush Current (peak) 163A JPL (TV-8) Endurance Test @ 125V AC for 25,000 operations: Steady State Current (rms) 8A; Minimum Inrush Current (peak) 117A UL: File No. E44145 - Recognized only when ordered with marking on switch. Add “/U” or “/CUL” before dash in part number to order UL recognized switch. All JPM models certified at 10A @ 125V AC, TV5 & JPL models at 16A @ 125V AC, TV8. VDE: License No. 113494 - Approved only when ordered with marking on switch. Add “/V” before dash in part number to order VDE approved switch. All JPM models approved at steady state 5A, inrush 80A, resistive 10A, & motor load 6A all at 250V AC. License No. 097579 All JPL models approved at steady state 8A, inrush 128A, resistive 16A, & motor load 8A all at 250V AC. C58 www.nkk.com Toggles Series JP Rockers Distinctive Characteristics Industry’s first molded pushbutton with TV rating. Designed to handle large inrush current. JPM models certified for TV-5 rating and JPL models for TV-8 rating. Programmable Illuminated PB C Pushbuttons Internationally Approved Pushbuttons Prominent external insulating barriers increase insulation resistance and dielectric strength. Keylocks Constructed for dust resistance with interior seal of polyphenylene sulfide (PPS) between actuator and contact area. Rotaries Specially designed to break light contact welds. Tactiles Slides Snap-action contact mechanism. Tilt Terminals are molded in and epoxy sealed to lock out flux, dust, and other contaminants. Outer case of heat resistant resin meet UL’s 94V-0 flammability standard. Supplement Accessories Indicators Touch Actual Size JPM www.nkk.com C59 Series JP Toggles Internationally Approved Pushbuttons TYPICAL SWITCH ORDERING EXAMPLE C M 2 6 B M TV-5 Rated 10A @ 125/250V AC L TV-8 Rated 16A @ 125/250V AC Keylocks 2 DPST Flat Cap with Barrier Flange P Plunger with Flat Flange; cap not supplied with plunger 6 OFF Cap Colors ON (Alternate Action with Latchdown) A Black B Ivory C Red H Gray Slides Rotaries SPST B Circuit Poles 1 H Actuators Ratings Programmable Illuminated PB Pushbuttons Rockers JP DESCRIPTION FOR TYPICAL ORDERING EXAMPLE Tactiles JPM26B-H Gray Flat Cap with Barrier Flange Tilt TV-5 Rated 10A @ 125/250V AC Indicators Touch DPST OFF-ON Circuit Accessories IMPORTANT: Specific models & ratings for international approvals noted on General Specifications page. Supplement Note: Wire harness & cable assemblies offered only in Americas C60 www.nkk.com Series JP Toggles Internationally Approved Pushbuttons TV-5 Rated Power Level 10A @ 125/250V AC L TV-8 Rated Power Level 16A @ 125/250V AC C Note: See General Specifications page to find complete explanation of TV ratings. Plunger Position Normal Down Normal Down OFF ON OPEN 1-1a SPST OFF ON OPEN 1-1a 2-2a DPST Model JPM16 1 (COM) JPL16 JPM26 DP Note: Terminal numbers are actually on the switch. JPL26 1a 1 (COM) 1a Keylocks SP Throw & Schematics 2 2a Rotaries Pole Connected Terminals Programmable Illuminated PB POLES & CIRCUIT ACTUATORS P Plunger with Flat Flange The flange is an integral part of the switch. This housing is black, molded polyamide matte finish material. Cap details below. No cap supplied. Tilt The barrier is an integral part of the switch. This housing is black, molded polyamide matte finish material. Slides Flat Cap with Barrier Flange Tactiles B Pushbuttons M Rockers RATINGS Cap Colors Available: A Black B Ivory C Red H The latchdown feature on this alternate action device provides visible, audible, and tactile feedback. This design gives smooth, responsive operation. Gray www.nkk.com Indicators (6.8) .268 Finish: Matte Supplement (18.0) .709 (22.0) .866 Cap Material: Polyphenylene Oxide The cap is flush with the barrier in normal position and .079” (2.0mm) below that in latchdown position. Accessories AT3021 Flat Cap for Actuator Type B with Barrier Flange Touch CAP COLORS C61 Series JP Toggles Internationally Approved Pushbuttons JPM & JPL Solder Lug/ .187”(4.75mm) Quick Connect Terminals Panel Thickness Range applies to both JPM & JPL models. C .039” ~ .157” (1.0mm ~ 4.0mm) TYPICAL SWITCH DIMENSIONS Flat Cap with Barrier Flange JPM & JPL Single & Double Pole Part No. (0.8) Typ .031 (20.8) .819 Rotaries (9.4) .370 (22.0) .866 (26.6) 1.047 COM 2a 1a 2 1 (31.0) 1.220 (0.5) .020 (18.0) .709 (24.0) .945 (4.5) .177 (2.5) .098 (26.0) 1.024 Latchdown Position (1.5) .059 JPM26B-H (7.2) .283 Single pole model does not have terminals 2 & 2a. Plunger with Flat Flange JPM & JPL Single & Double Pole Touch Indicators (1.0) .039 (3.3) Sq .130 (22.2) .874 (2.5) Sq .098 (1.0) .039 (2.5) .098 (18.3) .720 (24.0) .945 (20.8) .819 (0.8) Typ .031 (2.0) .079 Accessories (4.75) Typ .187 (10.4) .409 (21.2) .835 Part No. Supplement Epoxy Seal (7.2) (4.2) .283 (1.5) R .165 .059 (0.65) R (3.2) .026 .126 (4.75) .187 Thk = (0.5) .020 (21.2) .835 Slides Tactiles Tilt This switch assembly, when used with connectors, is not CSA approved. (28.0) 1.102 Keylocks Programmable Illuminated PB Pushbuttons Rockers PANEL CUTOUT & TERMINALS (9.4) .370 (26.6) 1.047 COM 2a 1a 2 1 (31.0) 1.220 (0.5) .020 (8.5) .335 (6.5) .256 (16.0) .630 (2.0) .079 (26.0) 1.024 (1.5) .059 (7.2) .283 (10.4) .409 (21.2) .835 (4.75) Typ .187 Latchdown Position JPL16P C62 Single pole model does not have terminals 2 & 2a. www.nkk.com