NB7V72M 1.8V / 2.5V Differential 2 x 2 Crosspoint Switch with CML Outputs Clock/Data Buffer/Translator http://onsemi.com Multi−Level Inputs w/ Internal Termination MARKING DIAGRAM* Description The NB7V72M is a high bandwidth, low voltage, fully differential 2 x 2 crosspoint switch with CML outputs. The NB7V72M design is optimized for low skew and minimal jitter as it produces two identical copies of Clock or Data operating up to 5 GHz or 6.5 Gb/s, respectively. As such, the NB7V72M is ideal for SONET, GigE, Fiber Channel, Backplane and other clock/data distribution applications. The differential IN/IN inputs incorporate internal 50 W termination resistors and will accept LVPECL, CML, or LVDS logic levels (see Figure 10). The 16 mA differential CML outputs provide matching internal 50 W terminations and produce 400 mV output swings when externally terminated with a 50 W resistor to VCC (see Figure 11). The NB7V72M is the 1.8 V/2.5 V CML version of the NB7L72M and is offered in a low profile 3x3 mm 16−pin QFN package. Application notes, models, and support documentation are available at www.onsemi.com. The NB7V72M is a member of the GigaComm™ family of high performance clock products. 1 1 QFN−16 MN SUFFIX CASE 485G NB7V 72M ALYWG G A = Assembly Location L = Wafer Lot Y = Year W = Work Week G = Pb−Free Package (Note: Microdot may be in either location) *For additional marking information, refer to Application Note AND8002/D. + Features • • • • • • • • • • • • 16 Maximum Input Data Rate > 6.5 Gb/s Data Dependent Jitter < 15 ps pk−pk Maximum Input Clock Frequency > 5 GHz Random Clock Jitter < 0.8 ps RMS, Max 150 ps Typical Propagation Delay 30ps Typical Rise and Fall Times Differential CML Outputs, 400 mV peak−to−peak, typical Operating Range: VCC = 1.71 V to 2.625 V with GND = 0 V Internal 50 W Input Termination Resistors QFN−16 Package, 3mm x 3mm −40°C to +85°C Ambient Operating Temperature These are Pb−Free Devices SEL0 IN0 VT0 0 IN0 1 0 IN1 VT1 + IN1 1 Q0 Q0 Q1 Q1 SEL1 Figure 1. Logic Diagram ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 7 of this data sheet. © Semiconductor Components Industries, LLC, 2009 October, 2009 − Rev. 1 1 Publication Order Number: NB7V72M/D NB7V72M VT0 16 IN0 1 IN0 2 SEL0 GND VCC 15 14 Exposed Pad (EP) Table 1. INPUT/OUTPUT SELECT TRUTH TABLE 13 12 Q0 11 Q0 SEL0* SEL1* Q0 Q1 L L IN0 IN0 L H IN0 IN1 H L IN1 IN0 H H IN1 IN1 NB7V72M IN1 3 10 Q1 IN1 4 9 Q1 *Defaults HIGH when left open 5 VT1 6 7 SEL1 GND 8 VCC Figure 2. Pin Configuration (Top View) Table 2. PIN DESCRIPTION Pin Name I/O Description 1 IN0 LVPECL, CML, LVDS Input Noninverted Differential Input. (Note 1) 2 IN0 LVPECL, CML, LVDS Input Inverted Differential Input. (Note 1) 3 IN1 LVPECL, CML, LVDS Input Inverted Differential Input. (Note 1) 4 IN1 LVPECL, CML, LVDS Input Noninverted Differential Input. (Note 1) 5 VT1 − 6 SEL1 LVCMOS Input 7 GND 8 VCC − 9 Q1 CML Output Noninverted Differential Output. (Note 1) 10 Q1 CML Output Inverted Differential Output. (Note 1) 11 Q0 CML Output Inverted Differential Output. (Note 1) 12 Q0 CML Output Noninverted Differential Output. (Note 1) 13 VCC − Positive Supply Voltage 14 GND − Negative Supply Voltage 15 SEL0 LVCMOS Input 16 VT0 − Internal 50 W Termination Pin for IN0 and IN0 − EP − The Exposed Pad (EP) on the QFN−16 package bottom is thermally connected to the die for improved heat transfer out of package. The exposed pad must be attached to a heat−sinking conduit. The pad is electrically connected to the die, and is recommended to be electrically and thermally connected to GND on the PC board. Internal 50 W Termination Pin for IN1 and IN1 Input Select logic pin for IN0 or IN1 Inputs to Q1 output. See Table 1, Input/Output Select Truth Table; pin defaults HIGH when left open. Negative Supply Voltage Positive Supply Voltage Input Select logic pin for IN0 or IN1 Inputs to Q0 output. See Table 1, Input/Output Select Truth Table; pin defaults HIGH when left open. 1. In the differential configuration when the input termination pins (VT0, VT1) are connected to a common termination voltage or left open, and if no signal is applied on INx/INx input, then the device will be susceptible to self−oscillation. 2. All VCC and GND pins must be externally connected to a power supply for proper operation. http://onsemi.com 2 NB7V72M Table 3. ATTRIBUTES Characteristics Value ESD Protection Human Body Model Machine Model > 4 kV > 200 V Moisture Sensitivity 16−QFN Level 1 Flammability Rating Oxygen Index: 28 to 34 RPU − Input Pullup Resistor 75kΩ Transistor Count UL 94 V−0 @ 0.125 in 210 Meets or exceeds JEDEC Spec EIA/JESD78 IC Latchup Test For additional information, see Application Note AND8003/D. Table 4. MAXIMUM RATINGS Symbol Parameter Condition 1 Condition 2 Rating Unit VCC Positive Power Supply GND = 0 V 3.0 V VIN Positive Input Voltage GND = 0 V −0.5 to VCC +0.5 V VINPP Differential Input Voltage |IN − IN| 1.89 V IIN Input Current Through RT (50 Ω Resistor) $40 mA TA Operating Temperature Range −40 to +85 °C Tstg Storage Temperature Range −65 to +150 °C qJA Thermal Resistance (Junction−to−Ambient) (Note 3) 42 35 °C/W °C/W qJC Thermal Resistance (Junction−to−Case) (Note 3) 4 °C/W Tsol Wave Solder 265 °C 0 lfpm 500 lfpm QFN−16 QFN−16 QFN−16 Pb−Free Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 3. JEDEC standard multilayer board − 2S2P (2 signal, 2 power) with 8 filled thermal vias under exposed pad. http://onsemi.com 3 NB7V72M Table 5. DC CHARACTERISTICS, Multi−Level Inputs VCC = 1.71 V to 2.625 V, GND = 0 V, TA = −40°C to +85°C (Note 4) Symbol Characteristic Min Typ Max Unit VCC = 2.5 V VCC = 1.8 V 120 80 145 110 170 140 mA VCC = 2.5 V VCC = 1.8 V VCC – 40 2460 1760 VCC – 20 2480 1780 VCC 2500 1800 mV VCC = 2.5 V VCC = 1.8 V VCC – 650 1850 1150 VCC – 400 2100 1400 VCC – 300 2200 1500 mV 1050 VCC − 100 mV VCC mV POWER SUPPLY CURRENT ICC Power Supply Current (Inputs and Outputs Open) CML OUTPUTS VOH Output HIGH Voltage (Note 5) VOL Output LOW Voltage (Note 5) DIFFERENTIAL CLOCK INPUTS DRIVEN SINGLE−ENDED (Note 6) (Figures 5 and 7) Vth Input Threshold Reference Voltage Range (Note 7) VIH Single−Ended Input HIGH Voltage Vth + 100 VIL Single−Ended Input LOW Voltage GND Vth − 100 mV VISE Single−Ended Input Voltage (VIH − VIL) 200 VCC − GND mV DIFFERENTIAL DATA/CLOCK INPUTS DRIVEN DIFFERENTIALLY (Figures 6 and 8) (Note 8) VIHD Differential Input HIGH Voltage (INn, INn) 1100 VCC mV VILD Differential Input LOW Voltage (INn, INn) GND VCC − 100 mV VID Differential Input Voltage (INn, INn) (VIHD − VILD) 100 1200 mV VCMR Input Common Mode Range (Differential Configuration, Note 9) (Figure 9) 1050 VCC − 50 mV IIH Input HIGH Current INn, INn (VTIN/VTIN Open) −150 150 mA IIL Input LOW Current INn, INn (VTIN/VTIN Open) −150 150 mA CONTROL INPUTS (SEL0, SEL1) VIH Input HIGH Voltage for Control Pins VCC x 0.65 VCC mV VIL Input LOW Voltage for Control Pins GND VCC x 0.35 mV IIH Input HIGH Current −150 20 150 mA IIL Input LOW Current −150 5 150 mA TERMINATION RESISTORS RTIN Internal Input Termination Resistor 40 50 60 W RTOUT Internal Output Termination Resistor 40 50 60 W NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 4. Input and output parameters vary 1:1 with VCC. 5. CML outputs loaded with 50 W to VCC for proper operation. 6. Vth, VIH, VIL,, and VISE parameters must be complied with simultaneously. 7. Vth is applied to the complementary input when operating in single−ended mode. 8. VIHD, VILD, VID and VCMR parameters must be complied with simultaneously. 9. VCMR min varies 1:1 with GND, VCMR max varies 1:1 with VCC. The VCMR range is referenced to the most positive side of the differential input signal. http://onsemi.com 4 NB7V72M Table 6. AC CHARACTERISTICS VCC = 1.71 V to 2.625 V; GND = 0 V; TA = −40°C to 85°C (Note 10) Symbol Characteristic Min VCC = 2.5 V VCC = 1.8 V Typ fMAX Maximum Input Clock Frequency fDATAMAX Maximum Operating Data Rate (PRBS23) 6.5 VOUTPP Output Voltage Amplitude (@ VINPPmin) fin ≤ 5 GHz (See Figures 3 and 10, Note 11) 200 400 tPLH, tPHL Propagation Delay to Differential Outputs, @ 1GHz, Measured at Differential Cross−point 110 150 tPLH TC Propagation Delay Temperature Coefficient tSKEW Output−to−Output Skew (within device) (Note 12) Device−to−Device Skew (tpdmax – tpdmin) tDC Output Clock Duty Cycle (Reference Duty Cycle = 50%) fin v 5GHz tjitter RJ – Output Random Jitter (Note 13) fin v 5 GHz DJ – Deterministic Jitter (Note 14) v9 Gbps VINPP Input Voltage Swing (Differential Configuration) (Note 15) 100 tr,, tf Output Rise/Fall Times @ 1 GHz (20% − 80%), Qn, Qn 20 Max 5 4.5 INn/INn to Qn/Qn Gbps mV 200 50 45 Unit GHz ps Dfs/°C 30 50 ps 50 55 % 0.5 0.8 10 ps RMS ps pk−pk 1200 mV 50 ps 30 NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 10. Measured using a 400 mV source, 50% duty cycle clock source. All output loading with external 50 W to VCC. Input edge rates w40 ps (20% − 80%). 11. Output voltage swing is a single−ended measurement operating in differential mode. 12. Skew is measured between outputs under identical transitions and conditions. Duty cycle skew is defined only for differential operation when the delays are measured from cross−point of the inputs to the cross−point of the outputs. 13. Additive RMS jitter with 50% duty cycle clock signal. 14. Additive Peak−to−Peak data dependent jitter with input NRZ data at PRBS23. 15. Input voltage swing is a single−ended measurement operating in differential mode. OUTPUT VOLTAGE AMPLITUDE (mV) 500 450 VCC Q AMP (mV) 400 350 INn 300 50 W VTn 250 200 50 W INn 0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 fin, Clock Input Frequency (GHz) Figure 3. CLOCK Output Voltage Amplitude (VOUTPP) vs. Input Frequency (fin) at Ambient Temperature (Typ) Figure 4. Input Structure http://onsemi.com 5 NB7V72M IN VIH Vth IN VIL IN IN Vth Figure 5. Differential Input Driven Single−Ended VCC Vthmax Figure 6. Differential Inputs Driven Differentially VIHmax VILmax VIH Vth VIL Vth VILD VILmin GND Figure 7. Vth Diagram VCC Figure 8. Differential Inputs Driven Differentially VIHDmax VCMmax IN VILDmax IN VCMR IN GND VIHD IN VIHmin Vthmin VCMmin VID = |VIHD(IN) − VILD(IN)| IN VINPP = VIH(IN) − VIL(IN) IN VIHDtyp VID = VIHD − VILD Q VILDtyp VOUTPP = VOH(Q) − VOL(Q) Q VIHDmin tPHL VILDmin tPLH Figure 9. VCMR Diagram Figure 10. AC Reference Measurement NB7V72M Receiver VCC VCC (Receiver) 50 W 50 W Q 50 W 50 W Q 16 mA GND Figure 11. Typical CML Output Structure and Termination http://onsemi.com 6 NB7V72M VCC 50 W Z = 50 W DUT Driver Device 50 W Q D Receiver Device Z = 50 W Q D Figure 12. Typical Termination for CML Output Driver and Device Evaluation VCC VCC VCC ZO = 50 W LVPECL Driver NB7V72M NB7V72M ZO = 50 W IN 50 W VT = VCC − 2 V ZO = 50 W VCC LVDS Driver 50 W IN 50 W VT = Open ZO = 50 W 50 W IN GND IN Figure 13. LVPECL Interface VCC GND GND VCC ZO = 50 W CML Driver VCC NB7V72M ZO = 50 W IN 50 W Differential Driver 50 W IN GND VCC NB7V72M VT = VCC ZO = 50 W GND Figure 14. LVDS Interface IN 50 W VT = VREFAC* ZO = 50 W 50 W IN GND GND GND Figure 16. Capacitor−Coupled Differential Interface (VT Connected to External VREFAC) Figure 15. Standard 50 W Load CML Interface *VREFAC bypassed to ground with a 0.01 mF capacitor ORDERING INFORMATION Package Shipping† NB7V72MMNG QFN−16 (Pb−free) 123 Units / Rail NB7V72MMNHTBG QFN−16 (Pb−free) 100 / Tape & Reel NB7V72MMNTXG QFN−16 (Pb−free) 3000 / Tape & Reel Device †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 7 NB7V72M PACKAGE DIMENSIONS 16 PIN QFN CASE 485G−01 ISSUE D D ÇÇÇ ÇÇÇ ÇÇÇ L1 DETAIL A PIN 1 LOCATION ALTERNATE TERMINAL CONSTRUCTIONS E ÉÉ ÉÉ EXPOSED Cu 0.15 C TOP VIEW 0.15 C A3 MOLD CMPD A1 DETAIL B (A3) DETAIL B 0.10 C NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.25 AND 0.30 MM FROM TERMINAL. 4. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS. 5. Lmax CONDITION CAN NOT VIOLATE 0.2 MM MINIMUM SPACING BETWEEN LEAD TIP AND FLAG L L A B ÉÉ ÇÇ ÇÇ ALTERNATE CONSTRUCTIONS A 16 X SEATING PLANE 0.08 C SIDE VIEW 16X L A1 5 8 4 e 0.575 0.022 EXPOSED PAD 3.25 0.128 0.30 0.012 EXPOSED PAD 9 E2 K 12 1 16 16X e 1.50 0.059 3.25 0.128 13 b 0.10 C A B 0.05 C MILLIMETERS MIN MAX 0.80 1.00 0.00 0.05 0.20 REF 0.18 0.30 3.00 BSC 1.65 1.85 3.00 BSC 1.65 1.85 0.50 BSC 0.18 TYP 0.30 0.50 0.00 0.15 SOLDERING FOOTPRINT* D2 DETAIL A NOTE 5 16X C DIM A A1 A3 b D D2 E E2 e K L L1 BOTTOM VIEW NOTE 3 0.50 0.02 0.30 0.012 SCALE 10:1 GigaComm is a trademark of Semiconductor Components Industries, LLC (SCILLC). mm Ǔ ǒinches *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Japan: ON Semiconductor, Japan Customer Focus Center 2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051 Phone: 81−3−5773−3850 http://onsemi.com 8 ON Semiconductor Website: http://onsemi.com Order Literature: http://www.onsemi.com/litorder For additional information, please contact your local Sales Representative. NB7V72M/D