ONSEMI NB6L14MNG

NB6L14
2.5 V/3.3 V 3.0 GHz
Differential 1:4 LVPECL
Fanout Buffer
Multi- Level Inputs with Internal Termination
http://onsemi.com
Description
MARKING
DIAGRAM*
The NB6L14 is a 3.0 GHz differential 1:4 LVPECL clock or data
fanout buffer. The differential inputs incorporate internal 50 termination resistors that are accessed through the VT pin. This feature
allows the NB6L14 to accept various logic standards, such as
LVPECL, LVCMOS, LVTTL, CML, or LVDS logic levels. The
VREF_AC reference output can be used to rebias capacitor-coupled
differential or single-ended input signals. The 1:4 fanout design was
optimized for low output skew applications.
The NB6L14 is a member of the ECLinPS MAX™ family of high
performance clock and data management products.
16
1
QFN-16
MN SUFFIX
CASE 485G
A
= Assembly Location
L
= Wafer Lot
Y
= Year
W
= Work Week
G
= Pb-Free Package
(Note: Microdot may be in either location)
Features
•Input Clock Frequency > 3.0 GHz
•Input Data Rate > 2.5 Gb/s
•< 20 ps Within Device Output Skew
•350 ps Typical Propagation Delay
•150 ps Typical Rise and Fall Times
•Differential LVPECL Outputs, 700 mV Amplitude, Typical
•LVPECL Mode Operating Range: VCC = 2.375 V to 3.63 V with
GND = 0 V
•Internal 50 Input Termination Resistors Provided
•VREF_AC Reference Output Voltage
•-40 °C to +85°C Ambient Operating Temperature
•Available in 3 mm x 3 mm 16 Pin QFN
•These are Pb-Free Devices
NB6L
14
ALYWG
G
*For additional marking information, refer to
Application Note AND8002/D.
Q0
Q0
Q1
Q1
IN
VT
IN
Q2
EN
D
Q
Q2
Q3
Q3
Figure 1. Simplified Logic Diagram
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 9 of this data sheet.
© Semiconductor Components Industries, LLC, 2007
May, 2007 - Rev. 1
1
Publication Order Number:
NB6L14/D
NB6L14
Q0
Q0
Q0
16
15
VCC GND
14
/Q0
Exposed Pad (EP)
13
Q1
Q1
1
12 IN
Q1
2
11 VT
Q2
3
10 VREF_AC
Q2
4
9
5
6
7
8
Q3
Q3
VCC
EN
/Q1
IN
50 VT
50 /IN
Q2
/Q2
IN
D
EN
Q
CLK
VREF_AC
Q3
/Q3
Figure 2. QFN-16 Pinout
(Top View)
Figure 3. Logic Diagram
Table 1. EN TRUTH TABLE
IN
IN
EN
Q0:Q3
Q0:Q3
0
1
x
1
0
x
1
1
0
0
1
0+
1
0
1+
+ = On next negative transition of the input signal (IN).
x = Don't care.
Table 2. PIN DESCRIPTION
Pin
Name
I/O
Description
1
Q1
LVPECL Output
Non-inverted Differential Output. Typically Terminated with 50 Resistor to
VCC–2.0 V.
2
Q1
LVPECL Output
Inverted Differential Output. Typically Terminated with 50 Resistor to VCC – 2.0 V.
3
Q2
LVPECL Output
Non-inverted Differential Output. Typically Terminated with 50 Resistor to
VCC – 2.0 V.
4
Q2
LVPECL Output
Inverted Differential Output. Typically Terminated with 50 Resistor to VCC – 2.0 V.
5
Q3
LVPECL Output
Non-inverted Differential Output. Typically Terminated with 50 Resistor to
VCC – 2.0 V.
6
Q3
LVPECL Output
Inverted Differential Output. Typically Terminated with 50 Resistor to VCC – 2.0 V.
7
VCC
-
8
EN
LVTTL/LVCMOS
9
IN
LVPECL, CML,
LVDS, HSTL
10
VREF_AC
11
VT
12
IN
LVPECL, CML,
LVDS, HSTL
13
GND
-
Negative Supply Voltage
14
VCC
-
Positive Supply Voltage
15
Q0
LVPECL Output
Noninverted Differential Output. Typically Terminated with 50 Resistor to
VCC–2.0 V.
16
Q0
LVPECL Output
Inverted Differential Output. Typically Terminated with 50 Resistor to VCC–2.0 V.
-
EP
-
Positive Supply Voltage
Synchronous Output Enable. When LOW, Q outputs will go LOW and Q outputs will
go HIGH on the next negative transition of IN input. The internal DFF register is
clocked on the falling edge of IN input (see Figure 16). The EN pin has an internal
pullup resistor and defaults HIGH when left open.
Inverted Differential Clock Input. Internal 50 Resistor to Termination Pin, VT.
Output Voltage Reference for capacitor-coupled inputs, only.
Internal 100 center-tapped Termination Pin for IN and IN.
Non-inverted Differential Clock Input. Internal 50 Resistor to Termination Pin, VT.
The Exposed Pad (EP) on the QFN-16 package bottom is thermally connected to the
die for improved heat transfer out of package. The exposed pad must be attached to
a heat-sinking conduit. The pad is not electrically connected to the die, but is
recommended to be electrically and thermally connected to GND on the PC board.
1. In the differential configuration when the input termination pin VT, is connected to a common termination voltage or left open, and if no signal
is applied on IN/IN inputs, then the device will be susceptible to self-oscillation.
http://onsemi.com
2
NB6L14
Table 3. ATTRIBUTES
Characteristics
ESD Protection
Value
Human Body Model
Machine Model
Moisture Sensitivity (Note 2)
Flammability Rating
QFN-16
Oxygen Index: 28 to 34
Transistor Count
> 4 kV
> 100 V
Level 1
UL 94 V-0 @ 0.125 in
167
Meets or exceeds JEDEC Spec EIA/JESD78 IC Latchup Test
2. For additional information, see Application Note AND8003/D.
Table 4. MAXIMUM RATINGS
Symbol
Parameter
Condition 1
VCC
Positive Power Supply
GND = 0 V
VIo
Positive Input/Output
GND = 0 V
IIN
Input Current
Condition 2
-0.5 V v VIo v VCC + 0.5 V
Rating
Unit
4.0
V
4.0
V
"50
mA
"2.0
mA
50
100
mA
mA
Source or Sink Current (IN/IN)
IVREF_AC
Source or Sink Current on VT Pin
IOUT
Output Current
TA
Operating Temperature Range
-40 to +85
°C
Tstg
Storage Temperature Range
-65 to +150
°C
JA
Thermal Resistance
(Junction-to-Ambient) (Note 3)
0 lfpm
500 lfpm
QFN-16
QFN-16
42
35
°C/W
°C/W
JC
Thermal Resistance (Junction-to-Case)
(Note 3)
QFN-16
4
°C/W
Tsol
Wave Solder
265
°C
Continuous
Surge
Pb-Free
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
3. JEDEC standard multilayer board - 2S2P (2 signal, 2 power) with 8 filled thermal vias under exposed pad.
http://onsemi.com
3
NB6L14
Table 5. DC CHARACTERISTICS, Multi-Level Inputs, LVPECL Outputs
VCC = 2.375 V to 3.63 V, GND = 0 V, TA = -40°C to +85°C
Symbol
ICC
Characteristic
Min
Typ
Max
Unit
35
47
65
mA
VCC - 1145
2155
1355
VCC - 1020
2280
1480
VCC - 895
2405
1605
mV
VCC = 3.3 V
VCC = 2.5 V
VCC - 1945
1355
555
VCC - 1875
1475
675
VCC - 1695
1605
805
mV
VCC = 3.3 V
VCC = 2.5 V
1100
VCC - 100
mV
VCC
mV
Power Supply Current (Inputs and Outputs Open)
LVPECL OUTPUT DC ELECTRICAL CHARACTERISTICS
VOH
VOL
Output HIGH Voltage (Notes 4 and 5) (Q, Q)
Output LOW Voltage (Notes 4 and 5) (Q, Q)
DIFFERENTIAL INPUT DRIVEN SINGLE-ENDED (See Figures 5 and 6)
Vth
Input Threshold Reference Voltage Range (Note 6)
VIH
Single-Ended Input High Voltage
Vth + 100
VIL
Single-Ended Input LOW Voltage
VEE
Vth - 100
mV
VISE
Single-Ended Input Voltage Amplitude (VIH - VIL)
200
VCC - GND
mV
VCC - 1.325
mV
VREFAC
VREFAC
Output Reference Voltage (VCC w 2.5 V)
VCC - 1.525
VCC - 1.425
DIFFERENTIAL INPUTS DRIVEN DIFFERENTIALLY (See Figures 7 and 8) (Note 7)
VIHD
Differential Input HIGH Voltage
1200
VCC
mV
VILD
Differential Input LOW Voltage
GND
VIHD - 100
mV
VCMR
Input Common Mode Range (Differential Configuration)
(Note 8)
950
VCC – 50
mV
VID
Differential Input Voltage (IN-IN) (VIHD- VILD)
100
VCC - GND
mV
IIH
Input HIGH Current
(VT Open)
IN/IN
-150
+150
A
IIL
Input LOW Current
(VT Open)
IN/IN
-150
+150
A
LVTTL/LVCMOS INPUT DC ELECTRICAL CHARACTERISTICS
VIH
Input HIGH Voltage
2.0
VCC
V
VIL
Input LOW Voltage
GND
0.8
V
IIH
Input HIGH Current, VCC = VIN = 3.63 V
-10
50
A
IIL
Input LOW Current, VCC = 3.63 V, VIN = 0 V
-150
0
A
TERMINATION RESISTORS
RTIN
Internal Input Termination Resistor (IN to VT)
40
50
60
RDIFF_IN
Differential Input Resistance (IN to IN)
80
100
120
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
4. LVPECL outputs loaded with 50 to VCC - 2.0 V for proper operation.
5. Input and output parameters vary 1:1 with VCC.
6. Vth is applied to the complementary input when operating in single-ended mode.
7. VIHD, VILD, VID and VCMR parameters must be complied with simultaneously.
8. VCMR min varies 1:1 with GND, VCMR max varies 1:1 with VCC. The VCMR range is referenced to the most positive side of the differential
input signal.
http://onsemi.com
4
NB6L14
Table 6. AC CHARACTERISTICS VCC = 2.375 V to 3.63 V, GND = 0 V, TA = -40°C to +85°C (Note 9)
Symbol
VOUTPP
Characteristic
Min
Typ
Output Voltage Amplitude (@ VINPPmin) (Note 10)
fIN ≤ 1.25 GHz
1.25 GHz ≤ fin ≤ 2.0 GHz
2.0 GHz ≤ fin ≤ 3.0 GHz
550
380
250
700
500
320
Max
Unit
mV
fDATA
Maximum Operating Data Rate
tPD
Propagation Delay
tS
Set-Up Time (Note 11)
EN to IN, IN
300
ps
tH
Hold Time (Note 11)
EN to IN, IN
300
ps
tSKEW
Within-Device Skew (Note 12)
IN to Q
2.5
Gb/s
350
ps
5.0
Device to Device Skew (Note 13)
tJITTER
20
RMS Random Jitter (Note 14)
ps
fIN = 2.5 GHz
Peak-to-Peak Data Dependent Jitter
(Note 15)
ps
150
1.0
fDATA = 2.5 Gb/s
14
VINPP
Input Voltage Swing/Sensitivity
(Differential Configuration) (Note 10)
100
tr,tf
Output Rise/Fall Times @ Full Output Swing
(20%-80%)
70
150
VCC - GND
mV
200
ps
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
9. Measured by forcing VINPP (min) from a 50% duty cycle clock source. All loading with an external RL = 50 to VCC – 2.0 V. Input edge
rates 40 ps (20%-80%).
10. Input and output voltage swing is a single-ended measurement operating in differential mode.
11. Set-up and hold times apply to synchronous applications that intend to enable/disable before the next clock cycle. For asynchronous
applications, set-up and hold times do not apply.
12. Within device skew is measured between two different outputs under identical power supply, temperature and input conditions.
13. Device to device skew is measured between outputs under identical transition @ 0.5 GHz.
14. Additive RMS jitter with 50% duty cycle clock signal.
15. Additive peak-to-peak data dependent jitter with input NRZ data at PRBS 2^23-1 and K28.5 at 2.5Gb/s.
http://onsemi.com
5
NB6L14
INn
VTn
INn
50 50 Figure 4. Input Structure
VCC
Vthmax
IN
VIH
VIHmax
VILmax
Vth
VIH
Vth
VIL
Vth
VIL
IN
VIHmin
Vthmin
Vth
VILmin
GND
Figure 6. Vth Diagram
Figure 5. Differential Input Driven
Single-Ended
VCC
VIH(MAX)
VIL
D
VIH
VID = VIHD - VILD
VCMR
VIL
D
VIH
Figure 7. Differential Inputs
Driven Differentially
VIL(MIN)
GND
Figure 8. VCMR Diagram
IN
VINPP = VIH(IN) - VIL(IN)
IN
Q
VOUTPP = VOH(Q) - VOL(Q)
Q
tPD
tPD
Figure 9. AC Reference Measurement
http://onsemi.com
6
NB6L14
VCC
VCC
VCC
NB6L14
Zo = 50 LVPECL
Driver
VCC
Zo = 50 IN
50 VT = VCC - 2 V
Zo = 50 LVDS
Driver
50 NB6L14
IN
50 VT = Open
Zo = 50 50 IN
IN
GND
GND
GND
GND
Figure 10. LVPECL Interface
Figure 11. LVDS Interface
VCC
VCC
NB6L14
Zo = 50 CML
Driver
IN
50 VT = VCC
Zo = 50 50 IN
GND
GND
Figure 12. Standard 50 W Load CML Interface
VCC
VCC
Zo = 50 Differential
Driver
VCC
VCC
NB6L14
Zo = 50 IN
50 VT = VREF_AC*
Zo = 50 Single-Ended
Driver
50 IN
GND
NB6L14
IN
50 VT = VREF_AC*
50 IN
GND
GND
Figure 13. Capacitor-Coupled
Differential Interface
(VT Connected to VREFAC)
GND
Figure 14. Capacitor-Coupled
Single-Ended Interface
(VT Connected to VREFAC)
*VREFAC bypassed to ground with a 0.01 F capacitor
http://onsemi.com
7
(Open)
VOUTPP OUTPUT VOLTAGE AMPLITUDE (mV)
(TYPICAL)
NB6L14
800
700
600
500
400
300
200
100
0
0
1
2
3
fout, CLOCK OUTPUT FREQUENCY (GHz)
Figure 15. Output Voltage Amplitude (VOUTPP) versus Output
Frequency at Ambient Temperature (Typical)
EN
VCC/2
VCC/2
tS
tH
/IN
IN
VINPP
tpd
/Q
VOUTPP
Q
Figure 16. EN Timing Diagram
Q
Zo = 50 D
Receiver
Device
Driver
Device
Q
Zo = 50 D
50 50 VTT
VTT = VCC - 2.0 V
Figure 17. Typical Termination for Output Driver and Device Evaluation
(See Application Note AND8020/D - Termination of ECL Logic Devices.)
http://onsemi.com
8
NB6L14
ORDERING INFORMATION
Package
Shipping†
NB6L14MNG
QFN-16, 3x3 mm
(Pb-Free)
123 Units / Rail
NB6L14MNR2G
QFN-16, 3x3 mm
(Pb-Free)
3000 / Tape & Reel
Device
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
9
NB6L14
PACKAGE DIMENSIONS
ÇÇ
ÇÇ
ÇÇ
PIN 1
LOCATION
D
16 PIN QFN
MN SUFFIX
CASE 485G-01
ISSUE C
A
B
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED
TERMINAL AND IS MEASURED BETWEEN
0.25 AND 0.30 MM FROM TERMINAL.
4. COPLANARITY APPLIES TO THE EXPOSED
PAD AS WELL AS THE TERMINALS.
5. Lmax CONDITION CAN NOT VIOLATE 0.2 MM
MINIMUM SPACING BETWEEN LEAD TIP
AND FLAG
E
0.15 C
TOP VIEW
0.15 C
DIM
A
A1
A3
b
D
D2
E
E2
e
K
L
(A3)
0.10 C
A
16 X
SEATING
PLANE
0.08 C
SIDE VIEW
A1
C
D2
16X
SOLDERING FOOTPRINT*
e
L
5
NOTE 5
EXPOSED PAD
8
4
9
0.575
0.022
E2
16X
K
12
1
16
16X
0.05 C
3.25
0.128
0.30
0.012
EXPOSED PAD
e
13
b
0.10 C A B
MILLIMETERS
MIN
MAX
0.80
1.00
0.00
0.05
0.20 REF
0.18
0.30
3.00 BSC
1.65
1.85
3.00 BSC
1.65
1.85
0.50 BSC
0.18 TYP
0.30
0.50
1.50
0.059
3.25
0.128
BOTTOM VIEW
NOTE 3
0.50
0.02
0.30
0.012
SCALE 10:1
mm Ǔ
ǒinches
*For additional information on our Pb-Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ECLinPS MAX is a trademark of Semiconductor Components Industries, LLC (SCILLC).
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada
Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800-282-9855 Toll Free
USA/Canada
ON Semiconductor Website: http://onsemi.com
Order Literature: http://www.onsemi.com/litorder
Japan: ON Semiconductor, Japan Customer Focus Center
2-9-1 Kamimeguro, Meguro-ku, Tokyo, Japan 153-0051
Phone: 81-3-5773-3850
http://onsemi.com
10
For additional information, please contact your
local Sales Representative.
NB6L14/D