RClamp0504PA RailClamp® Low Capacitance TVS Array PROTECTION PRODUCTS - RailClamp® Description Features Transient protection for high-speed data lines to RailClamp® TVS diodes are specifically designed to protect sensitive components which are connected to high-speed data and transmission lines from overvoltage caused by ESD (electrostatic discharge), CDE (cable discharge events), and EFT (electrical fast transients). The unique design incorporates surge rated, low capacitance steering diodes and a TVS diode in a single package. During transient conditions, the steering diodes direct the transient current to ground. The internal TVS diode clamps the transient voltage to a safe level. The low capacitance array configuration allows the user to protect up to four high-speed data lines. The RClamp®0504PA is in a 6-pin SLP1616P6 package. It measures 1.6 x 1.6 x 0.60mm. The leads are spaced at a pitch of 0.5mm and are finished with leadfree NiPdAu. They may be used to meet the ESD immunity requirements of IEC 61000-4-2, Level 4 (15kV air, 8kV contact discharge). The combination of small size, low capacitance, and high ESD surge capability makes them ideal for use in portable applications such as cellular phones, next generation color LCD displays, USB, and multi media card interfaces. IEC 61000-4-2 (ESD) ±15kV (air), ±8kV (contact) IEC 61000-4-4 (EFT) 40A (5/50ns) Array of surge rated diodes with internal TVS Diode Small package (1.6 x 1.6mm) saves board space Protects up to four I/O lines & power line Low capacitance (<3pF) for high-speed interfaces No insertion loss to 2.0GHz Low leakage current and clamping voltage Low operating voltage: 5.0V Solid-state silicon-avalanche technology Mechanical Characteristics SLP1616P6 6L package Pb-Free, Halogen Free, RoHS/WEEE Compliant Nominal Dimensions: 1.6 x 1.6 x 0.60 mm Lead Finish: NiPdAu Molding compound flammability rating: UL 94V-0 Packaging : Tape and Reel Applications Circuit Diagram USB 2.0 and USB OTG Multi Media Card (MMC) Interfaces SD Card Interfaces MDDI Ports SIM Ports Key Pads Gigabit Ethernet PIN Configuration 1.6 1 5 1.6 6 1 3 4 6 0.5 0.6 GND SLP1616P6 (Bottom View) Nominal Dimensions in mm Revision 4/27/2010 1 www.semtech.com RClamp0504PA PROTECTION PRODUCTS Absolute Maximum Rating R ating Symbol Value Units Peak Pulse Power (tp = 8/20μs) Pp k 150 Watts Peak Pulse Current (tp = 8/20μs) IP P 6 A ESD p er IEC 61000-4-2 (Air) ESD p er IEC 61000-4-2 (Contact) VESD 15 8 kV TJ -55 to +125 °C TSTG -55 to +150 °C Op erating Temp erature Storage Temp erature Electrical Characteristics (T=25oC) Parameter Symbol Conditions Minimum Typical Maximum Units Reverse Stand-Off Voltage VRWM Pin 5 to GN D 5 V Reverse Breakdown Voltage V BR It = 1mA Pin 5 to GN D Reverse Leakage Current IR VRWM = 5V, T=25°C Pin 5 to GN D 3 μA Clamping Voltage VC IPP = 1A, tp = 8/20μs Any I/O pin to GN D 15 V Clamping Voltage VC IPP = 6A, tp = 8/20μs Any I/O pin to GN D 25 V Clamping Voltage VC IPP = 6A, tp = 8/20μs Pin 5 to GN D 18 V Junction Capacitance Cj VR = 0V, f = 1MHz Any I/O pin to GN D 1.9 3 pF VR = 0V, f = 1MHz Between I/O pins 0.80 1 pF 6 V Note 1: I/O pins are pin 1, 3, 4, and 6 © 2010 Semtech Corp. 2 www.semtech.com RClamp0504PA PROTECTION PRODUCTS Typical Characteristics Non-Repetitive Peak Pulse Power vs. Pulse Time Power Derating Curve 10 110 90 % of Rated Power or IPP Peak Pulse Power - P PP (kW) 100 1 0.1 80 70 60 50 40 30 20 10 0 0.01 0.1 1 10 100 0 1000 25 50 75 100 125 150 Ambient Temperature - TA (oC) Pulse Duration - tp (μs) Pulse Waveform Clamping Voltage vs. Peak Pulse Current 110 Waveform Parameters: tr = 8µs td = 20µs 90 80 Percent of I PP 70 25 Clamping Voltage - VC (V) 100 e-t 60 50 40 td = IPP/2 30 20 Waveform Parameters: tr = 8µs td = 20µs 20 Pin 1, 3, 4, or 6 to pin 2 15 Pin 5 to pin 2 10 10 0 0 5 10 15 20 25 5 30 0 Time (µs) 2 3 4 Peak Pulse Current - IPP (A) 5 6 Normalized Capacitance vs. Reverse Voltage 8 1.5 7 1.4 f = 1MHz 1.3 6 1.2 5 CJ(VR) / CJ(VR=0) Forward Voltage - V F (V) Forward Voltage vs. Peak Pulse Current 1 4 3 Waveform Parameters: tr = 8µs td = 20µs 2 1 Between any two I/O pins 1.1 1 0.9 Any I/O Pin to Ground 0.8 0.7 0 0.6 0 1 2 3 4 5 6 0.5 Peak Pulse Current - IPP (A) © 2010 Semtech Corp. 0 3 1 2 3 Reverse Voltage - VR (V) 4 5 www.semtech.com RClamp0504PA PROTECTION PRODUCTS Typical Characteristics Insertion Loss S21 (I/O to Gnd) CH1 S21 LOG Analog Crosstalk 6 dB / REF 0 dB CH1 S21 1: -0.2295 dB 900 MHz LOG 20 dB/ REF 0 dB 2: -0.3160 dB 1.8 GHz 3: -1.0090 dB 2.5 GHz 3 0 dB 1 2 -6 dB -12 dB -18 dB -24 dB -30 dB -36 dB 1 MHz 10 MHz 100 MHz START. 030 MHz 3 1 GHz GHz START . 030 MHz STOP 3 000.000000 MHz STOP 3000. 000000 MHz ESD Clamping (8kV Contact per IEC 61000-4-2) Note: Data is taken with a 10x attenuator © 2010 Semtech Corp. 4 www.semtech.com RClamp0504PA PROTECTION PRODUCTS Applications Information Protection of Four Data Lines and Power Supply Line Device Connection Options for Protection of Four High-Speed Data Lines This device is designed to protect data lines by clamping them to a fixed reference. When the voltage on the protected line exceeds the reference voltage the steering diodes are forward biased, conducting the transient current away from the sensitive circuitry. Data lines are connected at pins 1, 3, 4 and 6. The center pin should be connected directly to a ground plane. The path length is kept as short as possible to minimize parasitic inductance. Pin 2 is not connected. The positive reference is connected at pin 5. The options for connecting the positive reference are as follows: 1 Gnd 1. To protect data lines and the power line, connect pin 5 directly to the positive supply rail (VCC). In this configuration the data lines are referenced to the supply voltage. The internal TVS diode prevents over-voltage on the supply rail. 2. In applications where the supply rail does not exit the system, the internal TVS may be used as the reference. In this case, pin 5 is not connected. The steering diodes will begin to conduct when the voltage on the protected line exceeds the working voltage of the TVS (plus one diode drop). Protection of Four Data Lines Using Internal TVS Diode as Reference 1 Gnd Figure 1 iguration (T op Side Vie w) 1.. Pin Conf Configuration (Top View) 1 2 3 6 Gnd 5 4 Pin Identification 1, 3, 4, 6 Input/Output Lines 2 N ot Connected 5 5V (Optional) or N /C Center Tab Ground © 2010 Semtech Corp. 5 www.semtech.com RClamp0504PA PROTECTION PRODUCTS Typical Applications Gnd 1 SIM Port - Protection of Three Data Lines and VCC USB OTG Receptable Carkit VBus DD+ ID GND To Phone Mini B Receptable Shield Gnd 1 Gnd Mini A Receptable USB OTG Carkit Protection © 2010 Semtech Corp. 6 www.semtech.com RClamp0504PA PROTECTION PRODUCTS Outline Drawing - SLP1616P6 A B D PIN 1 INDICATOR (LASER MARK) DIMENSIONS INCHES MILLIMETERS DIM MIN NOM MAX MIN NOM MAX E A SEATING PLANE aaa C A2 A A1 A2 b D D1 E E1 e L N aaa bbb C A1 D1 1 2 LxN E/2 E1 .020 .023 .026 0.00 .001 .002 (.006) .007 .010 .012 .059 .063 .067 .041 .047 .051 .059 .063 .067 .016 .022 .026 .020 BSC .013 .013 .016 6 .004 .004 0.50 0.58 0.65 0.00 0.03 0.05 (0.15) 0.20 0.25 0.30 1.50 1.60 1.70 1.05 1.20 1.30 1.50 1.60 1.70 0.40 0.55 0.65 0.50 BSC 0.25 0.33 0.40 6 0.09 0.09 N bxN bbb e C A B D/2 NOTES: 1. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES). 2. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS. Land Pattern - SLP1616P6 P X DIMENSIONS Z F G DIM B C P F G X Y Z (C) Y INCHES .051 .060 .020 .018 .035 .012 .025 .085 MILLIMETERS 1.30 1.52 0.50 0.45 0.89 0.30 0.63 2.15 B NOTES: 1. THIS LAND PATTERN IS FOR REFERENCE PURPOSES ONLY. CONSULT YOUR MANUFACTURING GROUP TO ENSURE YOUR COMPANY'S MANUFACTURING GUIDELINES ARE MET. © 2010 Semtech Corp. 7 www.semtech.com RClamp0504PA PROTECTION PRODUCTS Marking Ordering Information 0504P YYWW Part Number Lead Finish Qty per Reel R eel Size RClamp 0504PATCT Pb Free 3,000 7 Inch RailClamp and RClamp are marks of Semtech Corporation YYWW = Date Code Tape and Reel Specification Device Orientation in Tape Pin 1 in upper left towards sprocket holes A0 1.78 +/-0.10 mm Tape Width 8 mm B0 K0 1.78 +/-0.10 mm B, (Max) D 4.2 mm 1.5 + 0.1 mm - 0.0 mm ) 0.69 +/-0.10 mm D1 E 0.5 mm ±0.05 1.750±.10 mm F 3.5±0.05 mm K (MAX) P P0 P2 2.4 mm 4.0±0.1 mm 4.0±0.1 mm 2.0±0.05 mm T(MAX) 0.4 mm W 8.0 mm + 0.3 mm - 0.1 mm Contact Information Semtech Corporation Protection Products Division 200 Flynn Rd., Camarillo, CA 93012 Phone: (805)498-2111 FAX (805)498-3804 © 2010 Semtech Corp. 8 www.semtech.com