STGB10NC60KD, STGD10NC60KD STGF10NC60KD, STGP10NC60KD 10 A, 600 V short-circuit rugged IGBT Features TAB TAB ■ Lower on voltage drop (VCE(sat)) ■ Lower CRES / CIES ratio (no cross-conduction susceptibility) ■ Very soft ultra fast recovery antiparallel diode ■ Short-circuit withstand time 10µs 3 1 3 1 DPAK 2 D PAK TAB Description This IGBT utilizes the advanced PowerMESH™ process resulting in an excellent trade-off between switching performance and low on-state behavior. Applications High frequency motor controls ■ SMPS and PFC in both hard switch and resonant topologies ■ Motor drives Table 1. 1 TO-220FP Figure 1. ■ 3 3 1 2 2 TO-220 Internal schematic diagram Device summary Order codes Marking Packages STGB10NC60KDT4 GB10NC60KD D2PAK STGD10NC60KDT4 GD10NC60KD DPAK STGF10NC60KD GF10NC60KD TO-220FP STGP10NC60KD GP10NC60KD TO-220 Packaging Tape and reel Tube November 2009 Doc ID 11423 Rev 6 1/20 www.st.com 20 Contents STGx10NC60KD Contents 1 Electrical ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2.1 Electrical characteristics (curves) ............................. 8 3 Test circuits 4 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 5 Packaging mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 6 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 2/20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Doc ID 11423 Rev 6 STGx10NC60KD Electrical ratings 1 Electrical ratings Table 2. Absolute maximum ratings Value Symbol Parameter Unit D²PAK DPAK TO-220 TO-220FP VCES Collector-emitter voltage (VGE = 0) IC(1) Continuous collector current at TC = 25°C 20 9 A IC(1) Continuous collector current at TC = 100°C 10 6 A ICL(2) Turn-off latching current 30 A ICP(3) Pulsed collector current 30 A VGE Gate-emitter voltage ±20 V Diode RMS forward current at Tc=25°C 10 A IFSM Surge non repetitive forward current Tp = 10 ms sinusoidal 20 A PTOT Total dissipation at TC = 25°C VISO Insulation withstand voltage (RMS) from all three leads to external heat sink (t=1s;TC=25°C) tscw Short-circuit withstand time VCE = 0.5 VCES, Tj = 125 °C, RG = 10 Ω, VGE = 12 V Tstg Storage temperature IF Tj 600 65 62 -- V 25 W 2500 V 10 µs – 55 to 150 °C Operating junction temperature 1. Calculated according to the iterative formula T j ( max ) – T C I C ( T C ) = --------------------------------------------------------------------------------------------------------R thj – c × V CE ( sat ) ( max ) ( T j ( max ), I C ( T C ) ) 2. Vclamp = 80 % VCES, VGE = 15 V, RG = 10 Ω, TJ = 150 °C 3. Pulse width limited by maximum junction temperature and turn-off within RBSOA Doc ID 11423 Rev 6 3/20 Electrical ratings Table 3. STGx10NC60KD Thermal data Value Symbol Parameter TO-220 D²PAK Unit DPAK TO-220FP Rthj-case Thermal resistance junction-case IGBT 1.9 2 5 Rthj-case Thermal resistance junction-case diode 4 4.5 7 Rthj-amb Thermal resistance junction-ambient 62.5 100 62.5 4/20 Doc ID 11423 Rev 6 °C/W STGx10NC60KD 2 Electrical characteristics Electrical characteristics (Tj =25°C unless otherwise specified) Table 4. Symbol Static Parameter Test conditions Collector-emitter V(BR)CES breakdown voltage (VGE= 0) IC= 1mA VCE(sat) Collector-emitter saturation VGE= 15V, IC= 5A voltage VGE= 15V, IC= 5A, Tj= 125°C VGE(th) Gate threshold voltage VCE= VGE, IC= 250µA ICES Collector cut-off current (VGE = 0) IGES gfs(1) Min. Typ. Max. 600 Unit V 2.2 1.8 2.5 V V 6.5 V VCE=600 V, Tj = 125°C 150 1 µA mA Gate-emitter leakage current (VCE = 0) VGE= ±20V ±100 nA Forward transconductance VCE = 15V, IC= 5A 4.5 VCE= 600 V 15 S 1. Pulse test: pulse duration < 300 µs, duty cycle < 2 % Table 5. Symbol Cies Coes Cres Qg Qge Qgc Dynamic Parameter Test conditions Input capacitance Output capacitance Reverse transfer capacitance VCE = 25V, f = 1MHz, VGE = 0 Total gate charge Gate-emitter charge Gate-collector charge Min. (see Figure 19) Doc ID 11423 Rev 6 Unit - 380 46 8.5 - pF pF pF - 19 5 9 - nC nC nC VCE = 390V, IC = 5A, VGE = 15V, Typ. Max. 5/20 Electrical characteristics Table 6. Symbol td(on) tr (di/dt)on td(on) tr (di/dt)on tr(Voff) td(off) tf tr(Voff) td(off) tf Table 7. Symbol Eon(1) Eoff(2) Ets Eon(1) Eoff(2) Ets STGx10NC60KD Switching on/off (inductive load) Parameter Test conditions Turn-on delay time Current rise time Turn-on current slope Turn-on delay time Current rise time Turn-on current slope Min. Typ. Max. Unit - 17 6 655 - ns ns A/µs - 16.5 6.5 575 - ns ns A/µs - 33 72 82 - ns ns ns - 60 106 136 - ns ns ns Min. Typ. Max. Unit - 55 85 140 - µJ µJ µJ - 87 162 249 - µJ µJ µJ VCC = 390V, IC = 5A RG= 10Ω, VGE= 15V (see Figure 20) VCC = 390V, IC = 5A RG= 10Ω, VGE= 15V, Tj=125°C (see Figure 20) Vcc = 390V, IC = 5A, Off voltage rise time Turn-off delay time Current fall time RGE = 10Ω, VGE = 15V Off voltage rise time Turn-off delay time Current fall time RGE=10Ω, VGE =15V, Tj=125°C (see Figure 20) Vcc = 390V, IC = 5A, (see Figure 20) Switching energy (inductive load) Parameter Test conditions Turn-on switching losses Turn-off switching losses Total switching losses Turn-on switching losses Turn-off switching losses Total switching losses VCC = 390V, IC = 5A RG= 10Ω, VGE=15V (see Figure 20) VCC = 390V, IC = 5A RG= 10Ω, VGE= 15V, Tj= 125°C (see Figure 20) 1. Eon is the tun-on losses when a typical diode is used in the test circuit in figure 2. If the IGBT is offered in a package with a co-pak diode, the co-pack diode is used as external diode. IGBTs & Diode are at the same temperature (25°C and 125°C) 2. Turn-off losses include also the tail of the collector current 6/20 Doc ID 11423 Rev 6 STGx10NC60KD Table 8. Symbol Electrical characteristics Collector-emitter diode Parameter Test conditions Min Typ. Max. Unit - 2 1.6 - V V - ns nC A - ns nC A VF Forward on-voltage IF=5 A IF=5 A, Tj=125 °C trr Qrr Irrm Reverse recovery time Reverse recovery charge Reverse recovery current IF=5 A, VR=40 V, di/dt=100 A/µs (see Figure 5) - 22 14 1.3 trr Qrr Irrm Reverse recovery time Reverse recovery charge Reverse recovery current IF=5 A, VR=40 V, Tj=125 °C, di/dt=100 A/µs (see Figure 5) - 35 40 2.2 Doc ID 11423 Rev 6 7/20 Electrical characteristics STGx10NC60KD 2.1 Electrical characteristics (curves) Figure 2. Output characteristics Figure 3. Transfer characteristics Figure 4. Transconductance Figure 5. Collector-emitter on voltage vs temperature Figure 6. Gate charge vs gate-source voltage Figure 7. 8/20 Doc ID 11423 Rev 6 Capacitance variations STGx10NC60KD Figure 8. Electrical characteristics Normalized gate threshold voltage vs temperature Figure 10. Normalized breakdown voltage vs temperature Figure 9. Collector-emitter on voltage vs collector current Figure 11. Switching losses vs temperature Figure 12. Switching losses vs gate resistance Figure 13. Switching losses vs collector current Doc ID 11423 Rev 6 9/20 Electrical characteristics STGx10NC60KD Figure 14. Thermal impedance for D²PAK, DPAK and TO-220 Figure 15. Turn-off SOA Figure 16. Emitter-collector diode characteristics Figure 17. Thermal impedance for TO-220FP )&-! 4J # MAXIMUMVALUES 4J # MAXIMUMVALUES 4J # TYPICALVALUES 6&-6 10/20 Doc ID 11423 Rev 6 STGx10NC60KD 3 Test circuits Test circuits Figure 18. Test circuit for inductive load switching Figure 19. Gate charge test circuit Figure 20. Switching waveform Figure 21. Diode recovery time waveform Doc ID 11423 Rev 6 11/20 Package mechanical data 4 STGx10NC60KD Package mechanical data In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK is an ST trademark. 12/20 Doc ID 11423 Rev 6 STGx10NC60KD Package mechanical data D2PAK package mechanical data Table 9. mm inch Dim. Min. Typ. Max. Min. Typ. Max. A 4.40 4.60 0.173 0.181 A1 0.03 0.23 0.001 0.009 b 0.70 0.93 0.027 0.037 b2 1.14 1.70 0.045 0.067 c 0.45 0.60 0.017 0.024 c2 1.23 1.36 0.048 0.053 D 8.95 9.35 0.352 0.368 D1 7.50 E 10 E1 8.50 0.295 10.40 0.394 0.409 0.334 e 2.54 0.1 e1 4.88 5.28 0.192 0.208 H 15 15.85 0.590 0.624 J1 2.49 2.69 0.099 0.106 L 2.29 2.79 0.090 0.110 L1 1.27 1.40 0.05 0.055 L2 1.30 1.75 0.051 0.069 R V2 0.4 0° 0.016 8° 0° 8° Figure 22. D2PAK package drawing 0079457_M Doc ID 11423 Rev 6 13/20 Package mechanical data Table 10. STGx10NC60KD DPAK package mechanical data mm Dim. Min. Typ Max. A 2.20 2.40 A1 0.90 1.10 A2 0.03 0.23 b 0.64 0.90 b4 5.20 5.40 c 0.45 0.60 c2 0.48 0.60 D 6.00 6.20 D1 E 5.10 6.40 6.60 E1 4.70 e 2.28 e1 4.40 4.60 H 9.35 10.10 L 1 L1 2.80 L2 0.80 L4 0.60 1 R V2 0.20 0 o 8o Figure 23. DPAK package drawing 0068772_G 14/20 Doc ID 11423 Rev 6 STGx10NC60KD Package mechanical data Table 11. TO-220FP package mechanical data mm Dim. Min. Typ. Max. A 4.4 4.6 B 2.5 2.7 D 2.5 2.75 E 0.45 0.7 F 0.75 1 F1 1.15 1.70 F2 1.15 1.70 G 4.95 5.2 G1 2.4 2.7 H 10 10.4 L2 16 L3 28.6 30.6 L4 9.8 10.6 L5 2.9 3.6 L6 15.9 16.4 L7 9 9.3 Dia 3 3.2 Figure 24. TO-220FP package drawing L7 E A B D Dia L5 L6 F1 F2 F G H G1 L4 L2 L3 7012510_Rev_K Doc ID 11423 Rev 6 15/20 Package mechanical data Table 12. STGx10NC60KD TO-220 type A mechanical data mm Dim. Min. Typ. Max. A 4.40 4.60 b 0.61 0.88 b1 1.14 1.70 c 0.48 0.70 D 15.25 15.75 D1 1.27 E 10 10.40 e 2.40 2.70 e1 4.95 5.15 F 1.23 1.32 H1 6.20 6.60 J1 2.40 2.72 L 13 14 L1 3.50 3.93 L20 16.40 L30 28.90 ∅P 3.75 3.85 Q 2.65 2.95 Figure 25. TO-220 type A package drawing 0015988_S 16/20 Doc ID 11423 Rev 6 STGx10NC60KD 5 Packaging mechanical data Packaging mechanical data D 2 PAK FOOTPRINT TAPE AND REEL SHIPMENT REEL MECHANICAL DATA DIM. mm MIN. A B DIM. mm inch MIN. MAX. MIN. A0 10.5 10.7 0.413 0.421 B0 15.7 15.9 0.618 0.626 D 1.5 1.6 0.059 0.063 D1 1.59 1.61 0.062 0.063 E 1.65 1.85 0.065 0.073 0.449 0.456 MIN. 330 1.5 C 12.8 D 20.2 G 24.4 N 100 T TAPE MECHANICAL DATA inch MAX. MAX. 12.992 0.059 13.2 0.504 0.520 26.4 0.960 1.039 0795 3.937 30.4 1.197 BASE QTY BULK QTY 1000 1000 MAX. F 11.4 11.6 K0 4.8 5.0 0.189 0.197 P0 3.9 4.1 0.153 0.161 P1 11.9 12.1 0.468 0.476 P2 1.9 2.1 0.075 0.082 R 50 1.574 T 0.25 0.35 0.0098 0.0137 W 23.7 24.3 0.933 0.956 Doc ID 11423 Rev 6 17/20 Packaging mechanical data STGx10NC60KD DPAK FOOTPRINT All dimensions are in millimeters TAPE AND REEL SHIPMENT REEL MECHANICAL DATA DIM. mm MIN. A B 1.5 C 12.8 D 20.2 G 16.4 N 50 T TAPE MECHANICAL DATA DIM. mm MIN. MAX. A0 6.8 7 0.267 0.275 B0 10.4 10.6 0.409 0.417 12.1 0.476 1.6 0.059 0.063 1.85 0.065 0.073 B1 18/20 inch D 1.5 D1 1.5 E 1.65 MIN. MAX. 0.059 F 7.4 7.6 0.291 0.299 K0 2.55 2.75 0.100 0.108 P0 3.9 4.1 0.153 0.161 P1 7.9 8.1 0.311 0.319 P2 1.9 2.1 0.075 0.082 R 40 W 15.7 1.574 16.3 0.618 0.641 Doc ID 11423 Rev 6 inch MAX. MIN. MAX. 330 12.992 13.2 0.504 0.520 18.4 0.645 0.724 0.059 0.795 1.968 22.4 0.881 BASE QTY BULK QTY 2500 2500 STGx10NC60KD 6 Revision history Revision history Table 13. Document revision history Date Revision Changes 14-Jun-2005 1 New release. 19-Jul-2005 2 Complete version. 27-Jan-2006 3 Inserted ecopack indication. 01-Mar-2006 4 The document has been reformatted. 08-Feb-2007 5 Modified value on Table 6.: Switching on/off (inductive load). 24-Nov-2009 6 Inserted DPAK package option. Doc ID 11423 Rev 6 19/20 STGx10NC60KD Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2009 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 20/20 Doc ID 11423 Rev 6