UTC-IC TL082

UTC TL082
LINEAR INTEGRATED CIRCUIT
GENERAL PURPOSE DUAL
J-FET OPERATIONAL
AMPLIFIER
SOP-8
DESCRIPTION
The UTC TL082 is a high speed J-FET input dual
operational amplifier. It incorporates well matched,
high voltage J-FET and bipolar transistors in a
monolithic integrated circuit.
The device features high slew rates, low input bias
and offset current, and low offset voltage temperature
coefficient.
DIP-8
FEATURES
*Low input bias and offset current
TSSOP-8
*Wide common-mode (up to vcc+ ) and differential
voltage range
*Output short-circuit protection
*High input impedance J-FET input stage
*Internal frequency compensation
*Latch up free operation
*High slewrate:16V/µs(typ)
PIN CONFIGURATIONS
UTC
OFFSET NULL 1
1
INVERTING
INPUT 1
2
-
NON-INVERING
INPUT 1
3
+
Vcc-
4
8
Vcc+
7
OUTPUT 2
-
6
INVERTING
INPUT 2
+
5
NON-INVERING
INPUT 1
UNISONIC TECHNOLOGIES CO., LTD.
1
QW-R105-019,A
UTC TL082
LINEAR INTEGRATED CIRCUIT
BLOCK DIAGRAM
ABSOLUTE MAXIMUM RATINGS (Ta=25°C )
PARAMETER
SYMBOL
VALUE
UNIT
Supply Voltage (note 1)
Input Voltage (note 2)
Differential Input Voltage (note 3)
Power Dissipation
Output Short-Circuit Duration (note 4)
Operating Free Air Temperature Range
Storage Temperature Range
Vcc
Vi
Vid
Ptot
+-18
+-15
+-30
680
Infinite
0 to 70
-65 to 150
V
V
V
mW
NOTES:
Toper
Tstg
°C
°C
1. All voltage values, except differential voltage, are with respect to the zero reference level
(ground) of the supply voltages where the zero reference level is the midpoint between Vccand Vcc+.
2. The magnitude of the input voltage must never exceed the magnitude of the supply voltage
or 15 volts, whichever is less.
3. Differential voltages are at the non-inverting input terminal with respect to the inverting input
terminal.
4. The output may be shorted to ground or to either supply. Temperature and/or supply
voltages must be limited to ensure that the dissipation rating is not exceeded.
UTC
UNISONIC TECHNOLOGIES CO., LTD.
2
QW-R105-019,A
UTC TL082
LINEAR INTEGRATED CIRCUIT
UTC TL082C ELECTRICAL CHARACTERISTICS
( Vcc=±15V, Ta=25°C,Tmin=0°C ,Tmax=70°C , unless otherwise specified)
PARAMETER
SYMBOL
MIN
Input Offset Voltage (Rs=50Ω)
Ta=25°C
Tmin≦Ta≦Tmax
Input Offset Voltage Drift
Input Offset Current *
Ta=25°C
Tmin≦Ta≦Tmax
Input Bias Current *
Ta=25°C
Tmin≦Ta≦Tmax
Input Common Mode Voltage Range
Output Voltage Swing
Ta=25°C, RL=2kΩ,
Ta=25°C, RL=10kΩ
Tmin≦Ta≦Tmax, RL=2kΩ
Tmin≦Ta≦Tmax, RL=10kΩ
Large Signal Voltage Gain (RL=2kΩ,
Vo=±10V) Ta=25°C
Tmin≦Ta≦Tmax
Gain Bandwidth Product (Ta=25°C)
Vin=10mV,RL=2kΩ, CL=100pF,f=100kHZ
Input Resistance
Common Mode Rejection Ratio (RS=50Ω)
Ta=25°C
Tmin≦Ta≦Tmax
Supply Voltage Rejection Ratio (RS=50Ω)
Ta=25°C
Tmin≦Ta≦Tmax
Supply Current,no load
Ta=25°C
Tmin≦Ta≦Tmax
Channel Separation (Av=100, Ta=25°C)
Output Short-circuit Current
Ta=25°C
Tmin≦Ta≦Tmax
Slew Rate (Ta=25°C)
Vi=10V, RL=2kΩ, CL=100pF,unity gain
Rise Time (Ta=25°C)
Vi=20mV, RL=2kΩ, CL=100pF,unity gain
Overshoot (Ta=25°C)
Vi=20mV, RL=2kΩ, CL=100pF,unity gain
Total Harmonic Distortion (Ta=25°C)
Av=20dB, f=1kHzRL=2kΩ, CL=100pF,
Vo=2Vpp)
Phase Margin
Equivalent Input Noise Voltage
(RS=100Ω, f=1KHz)
TYP
MAX
UNIT
Vio
3
10
13
mV
Dvio
10
Iio
5
100
10
pA
nA
Iib
20
400
20
µV/°C
Vicm
±11
-12~+15
pA
nA
V
±Vopp
10
12
10
12
12
13.5
V
Avd
25
15
200
V/mV
2.5
4
1012
GBP
Ri
MHz
Ω
CMR
70
70
86
dB
SVR
70
70
86
dB
Icc
1. 4
V01/V02
120
Ios
SR
tr
Kov
2. 5
2.5
mA
dB
10
10
40
60
60
8
16
V/µs
0.1
µs
mA
%
10
THD
0.01
%
φm
45
en
15
Degrees
nV
Hz
*The Input bias currents are junction leakage currents, which approximately double for every 10°C increase
in the junction temperature.
UTC
UNISONIC TECHNOLOGIES CO., LTD.
3
QW-R105-019,A
UTC TL082
LINEAR INTEGRATED CIRCUIT
UTC TL082AC ELECTRICAL CHARACTERISTICS
( Vcc=±15V, Ta=25°C, Tmin=0°C ,Tmax=70°C, unless otherwise specified)
PARAMETER
SYMBOL
MIN
Input Offset Voltage (Rs=50Ω)
Ta=25°C
Tmin≦Ta≦Tmax
Input Offset Voltage Drift
Input Offset Current *
Ta=25°C
Tmin≦Ta≦Tmax
Input Bias Current *
Ta=25°C
Tmin≦Ta≦Tmax
Input Common Mode Voltage Range
Output Voltage Swing
Ta=25Ω, RL=2kΩ,
Ta=25°C, RL=10kΩ
Tmin≦Ta≦Tmax, RL=2kΩ
Tmin≦Ta≦Tmax, RL=10kΩ
Large Signal Voltage Gain (RL=2kΩ,
Vo=±10V) Ta=25°C
Tmin≦Ta≦Tmax
Gain Bandwidth Product (Ta=25°C)
Vin=10mV,RL=2kΩ, CL=100pF,f=100kHZ
Input Resistance
Common Mode Rejection Ratio (RS=50Ω)
Ta=25°C
Tmin≦Ta≦Tmax
Supply Voltage Rejection Ratio (RS=50Ω)
Ta=25°C
Tmin≦Ta≦Tmax
Supply Current,no load
Ta=25°C
Tmin≦Ta≦Tmax
Channel Separation (Av=100, Ta=25°C)
Output Short-circuit Current
Ta=25°C
Tmin≦Ta≦Tmax
Slew Rate (Ta=25°C)
Vi=10V, RL=2kΩ, CL=100pF,unity gain
Rise Time (Ta=25°C)
Vi=20mV, RL=2kΩ, CL=100pF, unity gain
Overshoot (Ta=25°C)
Vi=20mV, RL=2kΩ, CL=100pF,unity gain
Total Harmonic Distortion (Ta=25°C)
Av=20dB, f=1kHz,RL=2kΩ, CL=100pF,
Vo=2Vpp
Phase Margin
Equivalent Input Noise Voltage
(RS=100Ω, f=1KHz)
TYP
MAX
UNIT
Vio
3
6
7
Dvio
10
Iio
5
100
4
pA
nA
Iib
20
200
20
mV
µV/°C
Vicm
±11
-12~+15
pA
nA
V
±Vopp
10
12
10
12
12
13.5
V
Avd
50
25
200
V/mV
2.5
4
1012
GBP
Ri
MHz
Ω
CMR
80
80
86
dB
SVR
80
80
86
dB
Icc
1. 4
V01/V02
120
2. 5
2.5
mA
dB
Ios
10
10
40
SR
8
16
V/µs
0.1
µs
tr
Kov
60
60
mA
%
10
THD
0.01
%
φm
45
Degrees
en
15
nV
Hz
*The Input bias currents are junction leakage currents, which approximately double for every 10°C increase
in the junction temperature.
UTC
UNISONIC TECHNOLOGIES CO., LTD.
4
QW-R105-019,A
UTC TL082
LINEAR INTEGRATED CIRCUIT
UTC TL082BC ELECTRICAL CHARACTERISTICS
( Vcc=±15V, Ta=25°C, Tmin=0°C ,Tmax=70°C, unless otherwise specified)
PARAMETER
SYMBOL
MIN
Input Offset Voltage (Rs=50Ω)
Ta=25°C
Tmin≦Ta≦Tmax
Input Offset Voltage Drift
Input Offset Current *
Ta=25°C
Tmin≦Ta≦Tmax
Input Bias Current *
Ta=25°C
Tmin≦Ta≦Tmax
Input Common Mode Voltage Range
Output Voltage Swing
Ta=25Ω, RL=2kΩ,
Ta=25°C, RL=10kΩ
Tmin≦Ta≦Tmax, RL=2kΩ
Tmin≦Ta≦Tmax, RL=10kΩ
Large Signal Voltage Gain (RL=2kΩ,
Vo=±10V) Ta=25°C
Tmin≦Ta≦Tmax
Gain Bandwidth Product (Ta=25°C)
Vin=10mV,RL=2kΩ, CL=100pF,f=100kHZ
Input Resistance
Common Mode Rejection Ratio (RS=50Ω)
Ta=25°C
Tmin≦Ta≦Tmax
Supply Voltage Rejection Ratio (RS=50Ω)
Ta=25°C
Tmin≦Ta≦Tmax
Supply Current,no load
Ta=25°C
Tmin≦Ta≦Tmax
Channel Separation (Av=100, Ta=25°C)
Output Short-circuit Current
Ta=25°C
Tmin≦Ta≦Tmax
Slew Rate (Ta=25°C)
Vi=10V, RL=2kΩ, CL=100pF,unity gain
Rise Time (Ta=25°C)
Vi=20mV, RL=2kΩ, CL=100pF, unity gain
Overshoot (Ta=25°C)
Vi=20mV, RL=2kΩ, CL=100pF,unity gain
Total Harmonic Distortion (Ta=25°C)
Av=20dB, f=1kHz,RL=2kΩ, CL=100pF,
Vo=2Vpp
Phase Margin
Equivalent Input Noise Voltage (RS=100Ω,
f=1KHz)
TYP
MAX
UNIT
Vio
1
3
5
Dvio
10
Iio
5
100
4
pA
nA
Iib
20
200
20
mV
µV/°C
Vicm
±11
-12~+15
pA
nA
V
±Vopp
10
12
10
12
12
13.5
V
Avd
50
25
200
V/mV
2.5
4
1012
GBP
Ri
MHz
Ω
CMR
80
80
86
dB
SVR
80
80
86
dB
Icc
2. 4
V01/V02
120
Ios
SR
tr
Kov
10
10
8
40
3. 5
2.5
mA
dB
60
60
mA
16
V/µs
µs
0.1
%
10
THD
0.01
%
φm
45
15
Degrees
en
nV
Hz
*The Input bias currents are junction leakage currents, which approximately double for every 10°C increase
in the junction temperature.
UTC
UNISONIC TECHNOLOGIES CO., LTD.
5
QW-R105-019,A
UTC TL082
UTC
LINEAR INTEGRATED CIRCUIT
UNISONIC TECHNOLOGIES CO., LTD.
6
QW-R105-019,A
UTC TL082
LINEAR INTEGRATED CIRCUIT
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
Tamb=+25℃
No signal
No load
2
4
6
8
10
12
14
SUPPLY VOLTAGE(±V)
UTC
T O T AL H AR M O N IC D IS T O R T IO N
v e rs u s F R E Q U E N C Y
TOTAL HARMONIC DISTORTION
(%)
SUPPLYCURRENT
(mA)
SUPPLY CURRENT PER AMPLIFIER
versus SUPPLY VOLTAGE
16
1
0 .4
0 .1
Vc c = ± 1 5 V
Av = 1
Vo (rm s )= 6 V
Ta m b= 2 5 ℃
0 .0 4
0 .0 1
0 .0 0 4
0 .0 0 1
100
400 1K
4K 10K
40K 100K
F R E Q U E N C Y (H Z)
UNISONIC TECHNOLOGIES CO., LTD.
7
QW-R105-019,A
UTC TL082
LINEAR INTEGRATED CIRCUIT
PARAMETER MEASUREMENT INFORMATION
Figure 1: Voltage Follower
Figure2: Gain-of-10 Inverting Amplifier
1/2
TL082
10k Ω
-
1k Ω
eo
+
-
el
el
CL=100pF
RL=2k Ω
1/2
TL082
eo
+
RL
UTC
CL=100pF
UNISONIC TECHNOLOGIES CO., LTD.
8
QW-R105-019,A
UTC TL082
LINEAR INTEGRATED CIRCUIT
TYPICAL APPLICATIONS
100KHZ QUADRUPLE OSCILLATOR
1N 4148
18kΩ *
1kΩ
18pF
-
- 15V
18pF
1 /2
T L082
8 8 .4 k Ω
-
1 /2
T L082
+
8 8 .4 k Ω
+
6 c os ω t
6 s in ω t
1kΩ
18pF
8 8 .4 k Ω
1N 4148
18kΩ *
+ 15V
* T h e s e re s is to rs va lu e s
m a y b e a d ju s te d fo r a s ym m e tric a l o u tp u t
UTC assumes no responsibility for equipment failures that result from using products at values that
exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or
other parameters) listed in products specifications of any and all UTC products described or contained
herein. UTC products are not designed for use in life support appliances, devices or systems where
malfunction of these products can be reasonably expected to result in personal injury. Reproduction in
whole or in part is prohibited without the prior written consent of the copyright owner. The information
presented in this document does not form part of any quotation or contract, is believed to be accurate
and reliable and may be changed without notice.
UTC
UNISONIC TECHNOLOGIES CO., LTD.
9
QW-R105-019,A