BriLux 1W Light Source BTP-187XXCQ-XX-XX Package Dimension [Note 1] Features Highest Lumen Per Watt Long Operational Life More Energy Efficient IC Compatible Low DC Voltage Superior ESD Protection Smallest Footprint Applications Accent Lighting Automotive Exterior/Interior Light High Power Back Light Reading Light Marine/Miner’s Lighting Portable Lighting Tolerance: ± see spec Unit: ± mm Optical Characteristics at Ta=25ºC, IF=350mA PART NUMBER LED CHIP MATERIAL BTP-187NRCQ-XX-17 AlInGaP Lens Color Water Clear Wavelength/CCT Luminous VIEW ANGLE Flux @350mA(lm) 2θ1/2 Range (nm/K) Drive Voltage Min/Max Typ. Typ. (deg) 620~635 2.60V 17 lm[2] 90 [2] BTP-187YECQ-XX-17 AlInGaP Water Clear 585~595 2.60V 17 lm 90 BTP-187BLCQ-XX-08 AlInGaN Water Clear 460~470 3.60V 6 lm[2] 90 BTP-187GBCQ-XX-10 AlInGaN Water Clear 470~480 3.60V [2] 90 [2] 10 lm BTP-187PGCQ-XX-15 AlInGaN Water Clear 520~530 3.60V 15lm 90 BTP-187WHCQ-XX-30 AlInGaN Water Clear 3000K 8000K 3.60V 30 lm[2] 90 Note: 1) Picture for illustration purpose only. Please refer to outline dimension for actual package size. 2) Due to the CIE eye response curve in the wavelength range, the minimum luminous flux will vary over the wavelength range of λD. For example, luminous flux will vary from a minimum of 4.5lm at 460 to a typical of 15 lm at 480nm nm due to this effect. DB LECTRO Inc. 3600 boul. Matte suite i Brossard Qc J4Y-2Z2 tel:(450)-444-1424 fax:(450)-444-4714 www.dblectro.com BriLux 1W Light Source BTP-187XXCQ-XX-XX Absolute Maximum Ratings at Ta=25ºC Parameter Red/Yellow White/Blue DC Forward Current (mA)[1] 300 350 Peak Pulsed Forward Current (mA) 350 500 Average Forward Current (mA) 300 300 Reverse Voltage (V) 5 5 LED Junction Temperature (°C) [3] 120 120 Thermal Resistance without heatsink (°C/W) 80 80 Storage Temperature (°C) -20 to +80 -20 to +80 Operating Temperature (°C) -10 to +70 -10 to +70 Application Notes: 1. Proper forward current must be observed to maintain the junction temperature below maximum rating 2. Although all products listed are class one ESD protection (+/- 1KV by HBM mode), care must be fully taken when handling products 3. Specification is subjected to change for improvements without notice. DB LECTRO Inc. 3600 boul. Matte suite i Brossard Qc J4Y-2Z2 tel:(450)-444-1424 fax:(450)-444-4714 www.dblectro.com BriLux 1W Light Source BTP-187XXCQ-XX-XX Typical Electro-Optical Characteristics Curves at Ta=25ºC DB LECTRO Inc. 3600 boul. Matte suite i Brossard Qc J4Y-2Z2 tel:(450)-444-1424 fax:(450)-444-4714 www.dblectro.com BriLux 1W Light Source BTP-187XXCQ-XX-XX Recommended Soldering Pattern Important Notes: The information contained herein is presented only as a Guide for the application of our products. Brilliance Technologies assumes no responsibility for any infringement of intellectual property or other rights of the third parties which may result from its use. Brilliance Technologies continually improves the quality of our products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsible of the customer, when using Brilliance Technologies products, to comply with the standard of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such Brilliance Technologies products cause loss of human life, bodily injury or damage to property. Brilliance Technologies products listed in this data sheet are intended for usage in general electronics and/or non-commercial or industrial lighting products. These products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury. In developing your design, please ensure that Brilliance Technologies products are used within specified operating ranges as set forth in the most recent Brilliance Technologies data sheets. BT-Rev. 1.0B20040917 Specifications are subject to change for improvement without notice. Copyright © 2003 Brilliance Technologies Co., Ltd. All rights reserved. DB LECTRO Inc. 3600 boul. Matte suite i Brossard Qc J4Y-2Z2 tel:(450)-444-1424 fax:(450)-444-4714 www.dblectro.com