E13D8 Series E13D8 • RoHS Compliant (Pb-Free) • LVPECL Output Oscillators • 3.3V Supply Voltage • Ceramic 6-pad SMD Package • Stability to ±25ppm • Tri-State Output • Complementary Output • Available on Tape and Reel • Wide Range of Available Frequencies H L W 2.0 7.0 5.0 OSCILLATOR ELECTRICAL SPECIFICATIONS Nominal Frequency Operating Temperature Range Storage Temperature Range Supply Voltage (VCC) Input Current Frequency Tolerance / Stability Output Voltage Logic High (VOH) Output Voltage Logic Low (VOL) Peak to Peak Output Voltage Swing Rise Time / Fall Time Duty Cycle Load Drive Capability Logic Control / Additional Output Tri-State Input Voltage Standby Current Start Up Time RMS Phase Jitter Typical Phase Noise 75MHz, 77.76MHz, 80MHz, 100MHz, 106.25MHz, 125MHz, 150MHz, 155.52MHz, 156.25MHz, 159.375MHz, 187.5MHz, 212.5MHz, 250MHz, 311.04MHz, 312.5MHz 0°C to +70°C, or -40°C to +85°C -55°C to 125°C 3.3VDC ±5% With Load 75mA Maximum Inclusive of All Conditions: Calibration Tolerance at 25°C, ±50ppm Maximum, or ±25ppm Maximum Frequency Stability over the Operating Temperature Range, Supply Voltage Change, Output Load Change, 1st Year Aging at 25°C, Shock, and Vibration 20% to 80% of waveform at 50% of waveform VIH of 70% of VCC Minimum No Connection VIL of 30% of VCC Maximum Disabled Output, High Impedance, Without Load FJ = 12kHz to 20MHz Fo=156.250MHz MANUFACTURER CATEGORY ECLIPTEK CORP. OSCILLATOR VCC -1.4VDC Minimum, VCC -1.2VDC Typical, VCC -0.9VDC Maximum VCC -1.7VDC Minimum, VCC -1.85VDC Typical, VCC -2.0VDC Maximum 600mVdc Minimum, 800mVdc Typical, 1000mVdc Maximum 300pSec Typical, 600pSec Maximum 50 ±5(%) 50 Ohms into VCC-2.0VDC Tri-State and Complementary Output Enables Output Enables Output Disables Output: High Impedance 600µA Maximum 10 mSeconds Maximum 0.7pSec Typical, 1 pSec Maximum -60dBc/Hz at 10Hz Offset -90dBc/Hz at 100Hz Offset -115dBc/Hz at 1kHz Offset -129dBc/Hz at 10kHz Offset -130dBc/Hz at 100kHz Offset -131dBc/Hz at 1MHz Offset -148dBc/Hz at 10MHz Offset SERIES PACKAGE VOLTAGE CLASS REV.DATE E13D8 CERAMIC 3.3V OS4N 10/07 800-ECLIPTEK www.ecliptek.com for latest revision Specifications subject to change without notice. PART NUMBERING GUIDE E13D8 D 2 F - 155.520M TR FREQUENCY TOLERANCE & STABILITY/ OPERATING TEMPERATURE RANGE C=±25ppm Maximum over 0°C to +70°C D=±50ppm Maximum over 0°C to +70°C G=±25ppm Maximum over -40°C to +85°C H=±50ppm Maximum over -40°C to +85°C AVAILABLE OPTIONS Blank=Tubes TR=Tape and Reel (Standard) FREQUENCY LOGIC CONTROL/ADDITIONAL OUTPUT F=Tri-State and Complementary Output DUTY CYCLE 2=50 ±5(%) MECHANICAL DIMENSIONS SUGGESTED SOLDER PAD LAYOUT ALL DIMENSIONS IN MILLIMETERS ALL DIMENSIONS IN MILLIMETERS Pin 1: Tri-State Pin 2: No Connect Pin 3: Case Ground Pin 4: Output Pin 5: Complementary Output Pin 6: Supply Voltage Tolerances= +0.1 TAPE AND REEL DIMENSIONS ALL DIMENSIONS IN MILLIMETERS TAPE A B C D E 16±.3-.1 7.5±.1 6.75±.1 4 ±.1 2±.1 F G H J K 8±.1 B0* 1.5 +.1-0 A0* .3 ±.05 F M N O P Q 1.5 MIN 50 MIN 20.2 MIN 13±.2 40 MIN QTY/REEL 1,000 REEL L K0* R S T U V 2.5 MIN 10 MIN 22.4 MAX 360 MAX 16.4+2-0 *Compliant to EIA 481A ENVIRONMENTAL/MECHANICAL SPECIFICATIONS MARKING SPECIFICATIONS Line 1: ECLIPTEK Characteristic Specification Fine Leak Test Gross Leak Test Mechanical Shock Vibration Solderability Temperature Cycling Resistance to Soldering Heat Resistance to Solvents MIL-STD-883, Method 1014, Condition A MIL-STD-883, Method 1014, Condition C MIL-STD-202, Method 213, Condition C MIL-STD-883, Method 2007, Condition A MIL-STD-883, Method 2002 MIL-STD-883, Method 1010 MIL-STD-202, Method 210 MIL-STD-202, Method 215 Line 2: XX.XXX M Frequency in MHz (5 Digits Maximum + Decimal) Line 3: XX Y ZZ Week of Year Last Digit of Year Ecliptek Manufacturing Identifier MANUFACTURER CATEGORY SERIES PACKAGE VOLTAGE CLASS ECLIPTEK CORP. OSCILLATOR E13D8 CERAMIC 3.3V OS4N 800-ECLIPTEK www.ecliptek.com for latest revision REV.DATE 10/07 Specifications subject to change without notice.