Metal Oxide Varistors SMD multilayer varistor with Ni-barrier termination CT0402S14AHSG B72590T8140S160 Designation system CT 0402 S…A 14 HS G = Chip with three-layer- termination (Ag/Ni/Sn) = Dimensions of the device 04 x 02 (length x width in 1/100 inch) = Special tolerance of the varistor voltage = Maximum operating voltage = Designed for protection of high speed data lines = Taped version (cardboard tape, 7” reel, 10000 pieces/reel) Figure l b l = 1.0 ± 0.15 b = 0.5 ± 0.10 s = 0.5 ± 0.10 k = 0.2 ± 0.10 s k (all dimensions in mm) As far as patents or other rights of third parties are concerned, liability is only assumed for components per se, not for applications, processes and circuits implemented within components or assemblies. The information describes the type of component and shall not be considered as assured characteristics. Terms of delivery and rights to change design reserved. ISSUE DATE 28.01.2005 ISSUE e PUBLISHER KB VS PE PAGE 1/7 Metal Oxide Varistors SMD multilayer varistor with Ni-barrier termination CT0402S14AHSG B72590T8140S160 V-I-characteristic VAR9733A 200 V v 100 80 60 40 20 10 8 6 4 2 1 10 -5 10 -4 10 -3 10 -2 10 -1 10 0 A 10 1 i Max. current, energy and average power dissipation depending on ambient temperature % 100 90 80 70 60 50 40 30 20 10 0 -55 ISSUE DATE 28.01.2005 70 80 ISSUE 90 100 110 120 Ambient temperature e PUBLISHER 130 140 150 °C KB VS PE PAGE 2/7 Metal Oxide Varistors SMD multilayer varistor with Ni-barrier termination CT0402S14AHSG B72590T8140S160 Electrical data Maximum operating voltage RMS voltage DC voltage VRMS = 14 V VDC = 16 V Varistor voltage (@ 1 mA) Maximum clamping voltage (@ 1 A) Maximum average power dissipation Maximum surge current (8/20 µs) Maximum energy absorption (ESD) (@ ESD according to IEC 61000-4-2, 15 kV air discharge) VV = 23 up to 33 V VC = 66 V Pmax = 3 mW Imax = 1 x 2 A Emax = 30 mJ Capacitance (@ 1 MHz, 1V, 25 °C, typical value) C = 10 pF Response time Operating temperature Storage temperature (mounted parts) < 0.5 ns -40 … +85 °C -40 … +125 °C Termination material Part weight Ag/Ni/Sn 0.002 g (thickness not specified, adjusted to fulfill wettability specification according to IEC 60068-2-58) Application note The described component is designed to meet ESD level 4 requirements according to IEC 61000-4-2 (8 kV contact discharge, 150 pF, 330 Ω) ISSUE DATE 28.01.2005 ISSUE e PUBLISHER KB VS PE PAGE 3/7 Metal Oxide Varistors SMD multilayer varistor with Ni-barrier termination CT0402S14AHSG B72590T8140S160 Signal insertion loss1) 0 insertion loss [dB] -0.5 -1 -1.5 -2 -2.5 -3 -3.5 -4 -4.5 -5 0 50 100 150 200 250 300 frequency [MHz] 1) typical values, measured with network analyzer HP8753 E/S containing S-parameter test set. Stability to multiple ESD discharges2) 40 30 20 10 0 0 1 10 100 1000 10000 number of ESD pulses 2) 8 kV contact discharge, 150 pF, 330 Ω, according to IEC 61000-4-2. ISSUE DATE 28.01.2005 ISSUE e PUBLISHER KB VS PE PAGE 4/7 Metal Oxide Varistors SMD multilayer varistor with Ni-barrier termination CT0402S14AHSG B72590T8140S160 Recommended geometry of solder pad B C B A A = 0.6 mm B = 0.6 mm C = 0.5 mm E = 1.7 mm A D Recommended soldering temperature profile Soldering zone max. 7 s at max. temp. Cooling-down zone max. 2 C/s (natural air cooling) Preheating zone max. 2 C/s 300 C T 40 s 245 215 180 100 s 100 20 0 50 100 150 200 s 250 t VAR0543-W-E This component should be soldered within 12 months after delivery from EPCOS. They should be left in their original packings to avoid soldering problems due to oxidized terminals. Storage temperature: -25 to 45 °C Relative humidity: < 75% annual average, < 95% on maximum 30 days in a year. The usage of mild non-activated fluxes for soldering is recommended, as well as proper cleaning of the PCB. The components are suited for Pb-free soldering. ISSUE DATE 28.01.2005 ISSUE e PUBLISHER KB VS PE PAGE 5/7 Metal Oxide Varistors SMD multilayer varistor with Ni-barrier termination CT0402S14AHSG B72590T8140S160 Taping according to IEC 60286-3 Tape material: cardboard T P 2 P 0 Tape end (trailer) 40 min. empty cavities W F E D 0 G B 0 Leader T 1 T T A 0 1 P 1 2 25 min. empty cavities Direction of unreeling 300 mm cover tape Dimensions and tolerances: Definition Symbol Dimension Tolerance [mm] 0.6 [mm] ± 0.2 1.15 ± 0.2 1.5 ± 0.1 Sprocket hole pitch D0 P0 4.0 ± 0.1 1) Distance center hole to center compartment P2 2.0 ± 0.05 P1 W E 2.0 ± 0.1 8.0 1.75 ± 0.3 ± 0.1 F G 3.5 0.75 ± 0.05 min T T2 0.6 0.7 max. max. Compartment width Compartment length Sprocket hole diameter Pitch of the component compartments Tape width Distance edge to center of hole Distance center hole to center compartment Distance compartment to edge Thickness of cardboard tape Overall thickness 1) A0 B0 £ ± 0.2 mm over any 10 pitches ISSUE DATE 28.01.2005 ISSUE e PUBLISHER KB VS PE PAGE 6/7 Metal Oxide Varistors SMD multilayer varistor with Ni-barrier termination CT0402S14AHSG B72590T8140S160 Packing Each reel in airtight plastic bag with desiccant bag. Dimensions approx. 220 x 220 mm. Weight approx. 170 g. 6 bags in cardboard box, dimensions approx. 250 x 220 x 130 mm. Weight approx. 1 kg. Reel material: plastic Packing unit: 10000 pcs./reel Reel dimensions: Definition Dimension Tolerance [mm] [mm] A 180 +0/ -3 Reel width (inside) W1 8.4 +1.5/ -0 Reel width (outside) W2 14.4 max. Reel diameter Symbol Ó EPCOS AG 2005. Reproduction, publication and dissemination of this data sheet, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. Purchase orders are subject to the General Conditions for the Supply of Products and Services of the Electrical and Electronics Industry recommended by the ZVEI (German Electrical and Electronic Manufacturers' Association), unless otherwise agreed. ISSUE DATE 28.01.2005 ISSUE e PUBLISHER KB VS PE PAGE 7/7