FREESCALE MC68HC711D3_05

MC68HC711D3
MC68HC11D3
MC68HC11D0
MC68L11D0
Data Sheet
HC11
Microcontrollers
MC68HC711D3
Rev. 2.1
07/2005
freescale.com
MC68HC711D3
Data Sheet
To provide the most up-to-date information, the revision of our documents on the World Wide Web will be
the most current. Your printed copy may be an earlier revision. To verify you have the latest information
available, refer to:
http://www.freescale.com
Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc.
© Freescale Semiconductor, Inc., 2005. All rights reserved.
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
3
Revision History
The following revision history table summarizes changes contained in this document. For your
convenience, the page number designators have been linked to the appropriate location.
Revision History
Date
Revision
Level
Page
Number(s)
Description
Reformatted to current publications standards
N/A
Removed references to PROG mode.
September,
2003
2
Corrected pin assignments for:
Figure 1-2. Pin Assignments for 40-Pin Plastic DIP
Figure 1-3. Pin Assignments for 44-Pin PLCC
Added Figure 1-4. Pin Assignments for 44-Pin QFP
4
5
6
1.9 Interrupt Request (IRQ) — Reworked description for clarity.
7
2.4 Programmable Read-Only Memory (PROM) — Updated with additional
data.
13
Section 10. Ordering Information and Mechanical Specifications — Added
mechanical specifications for 44-pin plastic quad flat pack (QFP).
133
Added the following appendices:
Appendix A. MC68HC11D3 and MC68HC11D0
Appendix B. MC68L11D0
July,
2005
2.1
Throughout
Updated to meet Freescale identity guidelines.
137
143
Throughout
MC68HC711D3 Data Sheet, Rev. 2.1
4
Freescale Semiconductor
List of Chapters
Chapter 1 General Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Chapter 2 Operating Modes and Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Chapter 3 Central Processor Unit (CPU). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Chapter 4 Resets, Interrupts, and Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Chapter 5 Input/Output (I/O) Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Chapter 6 Serial Communications Interface (SCI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Chapter 7 Serial Peripheral Interface (SPI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Chapter 8 Programmable Timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Chapter 9 Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Chapter 10 Ordering Information and Mechanical Specifications . . . . . . . . . . . . . . . . . . 121
Appendix A MC68HC11D3 and MC68HC11D0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Appendix B MC68L11D0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
5
List of Chapters
MC68HC711D3 Data Sheet, Rev. 2.1
6
Freescale Semiconductor
Table of Contents
Chapter 1
General Description
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
1.10
1.11
1.12
1.13
1.14
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Supply (VDD, VSS, and EVSS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reset (RESET) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Crystal Driver and External Clock Input (XTAL and EXTAL) . . . . . . . . . . . . . . . . . . . . . . . . . . .
E-Clock Output (E). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interrupt Request (IRQ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Non-Maskable Interrupt/Programming Voltage (XIRQ/VPP) . . . . . . . . . . . . . . . . . . . . . . . . . . .
MODA and MODB (MODA/LIR and MODB/VSTBY) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Read/Write (R/W). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Port D Bit 6/Address Strobe (PD6/AS). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input/Output Lines (PA7–PA0, PB7–PB0, PC7–PC0, and PD7–PD0) . . . . . . . . . . . . . . . . . . .
13
13
13
14
16
16
16
16
17
18
18
18
18
18
Chapter 2
Operating Modes and Memory
2.1
2.2
2.2.1
2.2.2
2.2.3
2.2.4
2.3
2.3.1
2.3.2
2.3.3
2.4
2.4.1
2.4.2
2.4.3
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Single-Chip Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Expanded Multiplexed Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Special Bootstrap Mode (BOOT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Special Test Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control and Status Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RAM and I/O Mapping Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuration Control Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Programmable Read-Only Memory (PROM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Programming an Individual EPROM Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Programming the EPROM with Downloaded Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PROM Programming Control Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21
21
21
21
22
23
23
23
29
30
31
31
32
32
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
7
Table of Contents
Chapter 3
Central Processor Unit (CPU)
3.1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2
CPU Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.1
Accumulators A, B, and D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.2
Index Register X (IX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.3
Index Register Y (IY) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.4
Stack Pointer (SP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.5
Program Counter (PC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.6
Condition Code Register (CCR). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.6.1
Carry/Borrow (C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.6.2
Overflow (V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.6.3
Zero (Z). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.6.4
Negative (N) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.6.5
I-Interrupt Mask (I) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.6.6
Half Carry (H) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.6.7
X-Interrupt Mask (X) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.6.8
STOP Disable (S) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3
Data Types. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.4
Opcodes and Operands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.5
Addressing Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.5.1
Immediate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.5.2
Direct . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.5.3
Extended . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.5.4
Indexed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.5.5
Inherent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.5.6
Relative . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.6
Instruction Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
33
33
34
34
34
34
36
36
36
36
36
37
37
37
37
37
37
38
38
38
38
39
39
39
39
39
Chapter 4
Resets, Interrupts, and Low-Power Modes
4.1
4.2
4.2.1
4.2.2
4.2.3
4.2.4
4.2.5
4.3
4.3.1
4.3.2
4.3.3
4.3.4
4.3.5
4.3.6
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Resets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RESET Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power-On Reset (POR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Computer Operating Properly (COP) Reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clock Monitor Reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Configuration Options Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Software Interrupt (SWI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Illegal Opcode Trap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Real-Time Interrupt (RTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interrupt Mask Bits in the CCR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Priority Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Highest Priority I Interrupt and Miscellaneous Register (HPRIO) . . . . . . . . . . . . . . . . . . . .
47
47
47
47
47
48
48
49
51
51
51
51
52
58
MC68HC711D3 Data Sheet, Rev. 2.1
8
Freescale Semiconductor
4.4
4.4.1
4.4.2
Low-Power Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Chapter 5
Input/Output (I/O) Ports
5.1
5.2
5.3
5.3.1
5.3.2
5.4
5.4.1
5.4.2
5.4.3
5.5
5.5.1
5.5.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Port A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Port B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Port B Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Port B Data Direction Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Port C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Port C Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Port C Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Port C Data Direction Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Port D. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Port D Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Port D Data Direction Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
61
61
62
62
62
63
63
63
63
64
64
64
Chapter 6
Serial Communications Interface (SCI)
6.1
6.2
6.3
6.4
6.5
6.5.1
6.5.2
6.6
6.7
6.7.1
6.7.2
6.7.3
6.7.4
6.7.5
6.8
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Data Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transmit Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Receive Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wakeup Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Idle-Line Wakeup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Address-Mark Wakeup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SCI Error Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SCI Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SCI Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SCI Control Register 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SCI Control Register 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SCI Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Baud Rate Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Status Flags and Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
65
65
65
65
68
68
68
69
69
69
70
70
71
72
75
Chapter 7
Serial Peripheral Interface (SPI)
7.1
7.2
7.3
7.4
7.5
7.5.1
7.5.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPI Transfer Formats. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clock Phase and Polarity Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPI Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Master In/Slave Out (MISO). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Master Out/Slave In (MOSI). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
77
77
77
79
79
79
80
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
9
Table of Contents
7.5.3
7.5.4
7.6
7.7
7.7.1
7.7.2
7.7.3
Serial Clock (SCK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Slave Select (SS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPI System Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPI Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPI Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPI Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPI Data I/O Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
80
80
80
81
81
82
83
Chapter 8
Programmable Timer
8.1
8.2
8.3
8.3.1
8.3.2
8.3.3
8.4
8.4.1
8.4.2
8.4.3
8.4.4
8.4.5
8.4.6
8.4.7
8.4.8
8.4.9
8.4.10
8.5
8.5.1
8.5.2
8.5.3
8.6
8.7
8.7.1
8.7.2
8.7.3
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Timer Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Input Capture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Timer Control 2 Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Timer Input Capture Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Timer Input Capture 4/Output Compare 5 Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Output Compare (OC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Timer Output Compare Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Timer Compare Force Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Output Compare 1 Mask Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Output Compare 1 Data Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Timer Counter Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Timer Control 1 Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Timer Interrupt Mask 1 Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Timer Interrupt Flag 1 Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Timer Interrupt Mask 2 Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Timer Interrupt Flag 2 Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Real-Time Interrupt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Timer Interrupt Mask 2 Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Timer Interrupt Flag 2 Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Pulse Accumulator Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Computer Operating Properly Watchdog Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Pulse Accumulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Pulse Accumulator Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Pulse Accumulator Count Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Pulse Accumulator Status and Interrupt Bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Chapter 9
Electrical Characteristics
9.1
9.2
9.3
9.4
9.5
9.6
9.7
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Functional Operating Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Thermal Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DC Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Peripheral Port Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
105
105
106
106
107
109
114
MC68HC711D3 Data Sheet, Rev. 2.1
10
Freescale Semiconductor
9.8
9.9
Expansion Bus Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Serial Peripheral Interface Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Chapter 10
Ordering Information and Mechanical Specifications
10.1
10.2
10.3
10.4
10.5
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
40-Pin DIP (Case 711-03) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
44-Pin PLCC (Case 777-02) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
44-Pin QFP (Case 824A-01) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
121
121
121
122
123
Appendix A
MC68HC11D3 and MC68HC11D0
A.1
A.2
A.3
A.4
A.5
A.5.1
A.5.2
A.6
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MC68HC11D3 and MC68HC11D0 Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . .
Functional Operating Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Thermal Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
125
126
127
128
128
128
128
129
Appendix B
MC68L11D0
B.1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B.2
MC68L11D0 Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B.2.1
Functional Operating Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B.2.2
DC Electrical Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B.2.3
Control Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B.2.4
Peripheral Port Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B.2.5
Expansion Bus Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B.2.6
Serial Peripheral Interface Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B.3
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
131
131
131
131
133
133
134
135
136
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
11
Table of Contents
MC68HC711D3 Data Sheet, Rev. 2.1
12
Freescale Semiconductor
Chapter 1
General Description
1.1 Introduction
This section depicts the general characteristics and features of the MC68HC711D3 high-density
complementary metal-oxide semiconductor (HCMOS) microcontroller unit (MCU).
The MC68HC711D3 contains highly sophisticated on-chip peripheral functions. This high-speed,
low-power programmable read-only memory (PROM) MCU has a nominal bus speed of 3 MHz. The fully
static design allows operations at frequencies down to dc.
The MC68HC11D3 and MC68HC11D0 are read-only memory (ROM) based high-performance
microcontrollers (MCU) based on the MC68HC11E9 design. The MC68L11D0 is an extended-voltage
version of the MC68HC11D0 that can operate in applications that require supply voltages as low as 3.0 V.
The information in this document pertains to all the devices with the exceptions noted in Appendix A
MC68HC11D3 and MC68HC11D0 and Appendix B MC68L11D0.
1.2 Features
Features of the MC68HC711D3 include:
• Expanded 16-bit timer system with four-stage programmable prescaler
• Non-return-to-zero (NRZ) serial communications interface (SCI)
• Power-saving stop and wait modes
• 64 Kbytes memory addressability
• Multiplexed address/data bus
• Serial peripheral interface (SPI)
• 4 Kbytes of one-time programmable read-only memory (OTPROM)
• 8-bit pulse accumulator circuit
• 192 bytes of static random-access memory (RAM) (all saved during standby)
• Real-time interrupt (RTI) circuit
• Computer operating properly (COP) watchdog system
• Available in these packages:
– 40-pin plastic dual in-line package (DIP)
– 44-pin plastic leaded chip carrier (PLCC)
– 44-pin plastic quad flat pack (QFP)
1.3 Structure
Refer to Figure 1-1, which shows the structure of the MC68HC711D3 MCU.
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
13
General Description
NOT BONDED IN 40-PIN PACKAGE
MODA/LIR
MODB/VSTBY
RESET
IRQ
XIRQ/VPP
XTAL EXTAL
E
OSCILLATOR
MODE CONTROL
PA7
PA6
PA5
PA4
PA3
PA2
PA1
PA0
CLOCK LOGIC
INTERRUPT CONTROL
4 KBYTES
EPROM OR OTPROM
COP
PAI/OC1 PULSE ACCUMULATOR
OC2/OC1
OC3/OC1
OC4/OC1
TIMER
IC4/OC5/OC1
IC1
IC2
IC3
PERIODIC INTERRUPT
PORT A
192 BYTES STATIC RAM
SS
MC68HC711D3
CPU CORE
VSS
MOSI
MISO
VDD
SERIAL
COMMUNICATIONS
INTERFACE
(SCI)
SCK
SERIAL
PERIPHERAL
INTERFACE
(SPI)
TxD
RxD
EVSS
MULTIPLEXED ADDRESS/DATA BUS
PD0
PD1
PD2
PD3
PD4
PD5
PD6/AS
PD7/R/W
PC0
PC1
PC2
PC3
PC4
PC5
PC6
PC7
PB0
PB1
PB2
PORT D
PB3
PORT C
PB4
PORT B
PB5
DATA DIRECTION REGISTER D
PB6
DATA DIRECTION REGISTER C
PB7
DATA DIRECTION REGISTER B
Figure 1-1. MC68HC711D3 Block Diagram
1.4 Pin Descriptions
Refer to Figure 1-2, Figure 1-3, and Figure 1-4 for pin assignments.
MC68HC711D3 Data Sheet, Rev. 2.1
14
Freescale Semiconductor
Pin Descriptions
VSS
1
40
XTAL
PC0
2
39
EXTAL
PC1
3
38
E
PC2
4
37
MODA/LIR
PC3
5
36
MODB/VSTBY
PC4
6
35
PB0
PC5
7
34
PB1
PC6
8
33
PB2
PC7
9
32
PB3
XIRQ/VPP
10
31
PB4
PD7/R/W
11
30
PB5
PD6/AS
12
29
PB6
RESET
13
28
PB7
IRQ
14
27
PA0
PD0
15
26
PA1
PD1
16
25
PA2
PD2
17
24
PA3
PD3
18
23
PA5
PD4
19
22
PA7
PD5
20
21
VDD
EXTAL
E
MODA/LIR
MODB/VSTBY
42
41
40
VSS
2
XTAL
PC0
3
43
PD1
4
EVSS
PC2
5
44
PC3
6
Figure 1-2. Pin Assignments for 40-Pin Plastic DIP
7
39
PB0
PC5
8
38
PB1
PC6
9
37
PB2
PC7
10
36
PB3
XIRQ/VPP
11
35
PB4
PD7/R/W
12
34
PB5
PD6/AS
13
33
PB6
RESET
14
32
PB7
1
PC4
24
25
26
27
28
PA5
PA4
PA3
PA2
23
PA6
PA7
22
VDD
PA1
21
29
20
17
PD5
PD1
PD4
PA0
19
NC
30
18
31
16
PD3
15
PD2
IRQ
PD0
Figure 1-3. Pin Assignments for 44-Pin PLCC
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
15
38
3
31
PB2
PC7
4
30
PB3
XIRQ
5
29
PB4
PD7
6
28
PB5
PD6
7
27
PB6
RESET
8
26
PB7
IRQ
9
25
NC
10
24
PA0
15
16
17
18
19
20
21
23
PA1
PD5
VDD
PA7
PA6
PA5
PA4
PA3
PA2
MODB
XTAL
39
PC6
14
MODA
VSS
40
PB1
PD4
34
EVSS
41
32
13
35
PC0
42
2
12
E
PC1
43
PB0
PD3
36
PC2
1
PC5
PD0
PD1
37
PC3
PC4
PD2
EXTAL
General Description
Figure 1-4. Pin Assignments for 44-Pin QFP
1.5 Power Supply (VDD, VSS, and EVSS)
Power is supplied to the MCU through VDD and VSS. VDD is the power supply (+5 V ±10%) and VSS is
ground (0 V). EVSS, available on the 44-pin PLCC and QFP, is an additional ground pin.
1.6 Reset (RESET)
An active low bidirectional control signal, RESET, acts as an input to initialize the MCU to a known startup
state. It also acts as an open-drain output to indicate that an internal failure has been detected in either
the clock monitor or computer operating properly (COP) watchdog circuit. In addition, the state of this pin
is one of the factors governing the selection of BOOT mode.
1.7 Crystal Driver and External Clock Input (XTAL and EXTAL)
These two pins provide the interface for either a crystal or a CMOS compatible clock to control the internal
clock generator circuitry. The frequency applied to these pins is four times higher than the desired E-clock
rate. Refer to Figure 1-5 for crystal and clock connections.
1.8 E-Clock Output (E)
E is the output connection for the internally generated E clock. The signal from E is used as a timing
reference. The frequency of the E-clock output is one fourth that of the input frequency at the XTAL and
EXTAL pins. The E clock can be turned off in single-chip mode for greater noise immunity if desired. See
4.3.6 Highest Priority I Interrupt and Miscellaneous Register (HPRIO) for details.
MC68HC711D3 Data Sheet, Rev. 2.1
16
Freescale Semiconductor
Interrupt Request (IRQ)
MCU
4xE
CMOS-COMPATIBLE
EXTERNAL OSCILLATOR
EXTAL
XTAL
NC OR
10K–100K
LOAD
FIRST MCU
SECOND MCU
25 pF *
EXTAL
EXTAL
10 M
4xE
CRYSTAL
25 pF *
XTAL
NC OR
10K–100K
LOAD
XTAL
MCU
25 pF *
EXTAL
10 M
4xE
CRYSTAL
25 pF *
XTAL
* Values includes all stray capacitances.
Figure 1-5. Oscillator Connections
1.9 Interrupt Request (IRQ)
The IRQ input provides a means of applying asynchronous interrupt requests to the microcontroller unit
(MCU). Either negative edge-sensitive triggering or level-sensitive triggering is program selectable by
using the IRQE bit of the OPTION register. IRQ is always configured to level-sensitive triggering at reset.
While the programmable read-only memory (PROM) is being programmed, this pin provides the chip
enable (CE) signal. To prevent accidental programming of the PROM during reset, an external resistor is
required on IRQ to pull the pin to VDD.
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
17
General Description
1.10 Non-Maskable Interrupt/Programming Voltage (XIRQ/VPP)
The XIRQ input provides the capability for asynchronously applying non-maskable interrupts to the MCU
after a power-on reset (POR). During reset, the X bit in the condition code register (CCR) is set masking
any interrupt until enabled by software. This level-sensitive input requires an external pullup resistor to
VDD.
In the programming configuration of the bootstrap mode, this pin is used to supply one-time
programmable read-only memory (OTPROM) programming voltage, VPP, to the MCU. To avoid
programming accidents during reset, this pin should be equal to VDD during normal operation unless
XIRQ is active.
1.11 MODA and MODB (MODA/LIR and MODB/VSTBY)
As reset transitions, these pins are used to latch the part into one of the four central processor unit (CPU)
controlled modes of operation. The LIR output can be used as an aid to debugging once reset is
completed. The open-drain LIR pin goes to an active low during the first E-clock cycle of each instruction
and remains low for the duration of that cycle. The VSTBY input is used to retain random-access memory
(RAM) contents during power down.
1.12 Read/Write (R/W)
This pin performs either of two separate functions, depending on the operating mode.
• In single-chip and bootstrap modes, R/W functions as input/output port D bit 7. Refer to Chapter 5
Input/Output (I/O) Ports for further information.
• In expanded multiplexed and test modes, R/W performs a read/write function. R/W controls the
direction of transfers on the external data bus.
1.13 Port D Bit 6/Address Strobe (PD6/AS)
This pin performs either of two separate functions, depending on the operating mode.
• In single-chip and bootstrap modes, the pin functions as input/output port D bit 6.
• In the expanded multiplexed and test modes, it provides an address strobe (AS) function. AS is
used to demultiplex the address and data signals at port C.
Refer to Chapter 2 Operating Modes and Memory for further information.
1.14 Input/Output Lines (PA7–PA0, PB7–PB0, PC7–PC0, and PD7–PD0)
In the 44-pin PLCC package, 32 input/output lines are arranged into four 8-bit ports: A, B, C, and D. The
lines of ports B, C, and D are fully bidirectional. Port A has two bidirectional, three input-only, and three
output-only lines in the 44-pin PLCC packaging. In the 40-pin DIP, two of the output-only lines are not
bonded.
Each of these four ports serves a purpose other than input/output (I/O), depending on the operating mode
or peripheral functions selected.
NOTE
Ports B, C, and two bits of port D are available for I/O functions only in
single-chip and bootstrap modes.
MC68HC711D3 Data Sheet, Rev. 2.1
18
Freescale Semiconductor
Input/Output Lines (PA7–PA0, PB7–PB0, PC7–PC0, and PD7–PD0)
Refer to Table 1-1 for details about the functions of the 32 port signals within different operating modes.
Table 1-1. Port Signal Functions
Port/Bit
Single-Chip
and Bootstrap Mode
Expanded Multiplexed
and Special Test Mode
PA0
PA0/IC3
PA1
PA1/IC2
PA2
PA2/IC1
PA3
PA3/OC5/IC4/and-or OC1
(1)
PA4/OC4/and-or OC1
PA4
PA5
PA5/OC3/and-or OC1
(1)
PA6/OC2/and-or OC1
PA6
PA7
PB0
PA7/PAI/and-or OC1
PB0
A8
PB1
PB1
A9
PB2
PB2
A10
PB3
PB3
A11
PB4
PB4
A12
PB5
PB5
A13
PB6
PB6
A14
PB7
PB7
A15
PC0
PC0
A0/D0
PC1
PC1
A1/D1
PC2
PC2
A2/D2
PC3
PC3
A3/D3
PC4
PC4
A4/D4
PC5
PC5
A5/D5
PC6
PC6
A6/D6
PC7
PC7
A7/D7
PD0
PD0/RxD
PD1
PD1/TxD
PD2
PD2/MISO
PD3
PD3/MOSI
PD4
PD4/SCK
PD5
PD5/SS
PD6
PD6
AS
PD7
PD7
R/W
1. In the 40-pin package, pins PA4 and PA6 are not bonded. Their associated I/O and output
compare functions are not available externally. They can still be used as internal software
timers, however.
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
19
General Description
MC68HC711D3 Data Sheet, Rev. 2.1
20
Freescale Semiconductor
Chapter 2
Operating Modes and Memory
2.1 Introduction
This section contains information about:
• The modes that define MC68HC711D3 operating conditions
• The on-chip memory that allows the microcontroller unit (MCU) to be configured for various
applications
• The 4-Kbytes of programmable read-only memory (PROM)
2.2 Operating Modes
The MC68HC711D3 uses two dedicated pins, MODA and MODB, to select one of two normal operating
modes or one of two special operating modes. A value reflecting the microcontroller unit (MCU) status or
mode selected is latched on bits SMOD and MDA of the highest priority I-bit interrupt and miscellaneous
register (HPRIO) on the rising edge of reset. The normal operating modes are the single-chip and
expanded-multiplexed modes. The special operating modes are the bootstrap and test modes. Table 2-1
shows mode selection according to the values encoded on the MODA and MODB pins, and the value
latched in the SMOD and MDA bits.
Table 2-1. Mode Selection
RESET
MODA
MODB
1
0
1
1
1
1
Mode Selected
SMOD
MDA
Normal — single chip
0
0
1
Normal — expanded multiplexed
0
1
0
0
Special — bootstrap (BOOT)
1
0
1
1
0
Special — test
1
1
0
0
0
Reserved
X
X
2.2.1 Single-Chip Mode
In single-chip mode, the MCU functions as a self-contained microcontroller and has no external address
or data bus. The 4-Kbyte erasable programmable read-only memory (EPROM) would contain all program
code and is located at $F000–$FFFF. This mode provides maximum use of the pins for on-chip peripheral
functions, and all the address and data activity occurs within the MCU.
2.2.2 Expanded Multiplexed Mode
In the expanded-multiplexed mode, the MCU can address up to 64 Kbytes of address space. High-order
address bits are output on the port B pins. Low-order address bits and the bidirectional data bus are
multiplexed on port C. The AS pin provides the control output used in demultiplexing the low-order
address. The R/W pin is used to control the direction of data transfer on the port C bus.
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
21
Operating Modes and Memory
If this mode is entered out of reset, the EPROM is located at $7000–$7FFF and vector accesses are from
external memory. To be in expanded-multiplexed mode with EPROM located at $F000–$FFFF, it is
necessary to start in single-chip mode, executing out of EPROM, and then set the MDA bit of the HPRIO
register to switch mode.
NOTE
R/W, AS, and the high-order address bus (port B) are inputs in single-chip
mode. These inputs may need to be pulled up so that off-chip accesses
cannot occur while the MCU is in single-chip mode.
2.2.3 Special Bootstrap Mode (BOOT)
This special mode is similar to single-chip mode. The resident bootloader program contains a 256-byte
program in a special on-chip read-only memory (ROM). The user downloads a small program into
on-board RAM using the SCI port. Program control is passed to RAM when an idle line of at least four
characters occurs. In this mode, all interrupt vectors are mapped to RAM (see Table 2-2), so that the user
can set up a jump table, if desired.
Bootstrap mode (BOOT) is entered out of reset if the voltage level on both MODA and MODB is low. The
programming aspect of bootstrap mode, used to program the one-time programmable ROM (OTPROM)
through the MCU, is entered automatically if IRQ is low and programming voltage is available on the VPP
pin. IRQ should be pulled up while in reset with MODA and MODB configured for bootstrap mode to
prevent unintentional programming of the EPROM.
This versatile mode (BOOT) can be used for test and diagnostic functions on completed modules and for
programming the on-board PROM. The serial receive logic is initialized by software in the bootloader
ROM, which provides program control for the SCI baud rate and word format. Mode switching to other
modes can occur under program control by writing to the SMOD and MDA bits of the HPRIO register. Two
special bootloader functions allow either an immediate jump-to-RAM at memory address $0000 or an
immediate jump-to-EPROM at $F000.
Table 2-2. Bootstrap Mode Jump Vectors
Address
Vector
00C4
SCI
00C7
SPI
00CA
Pulse accumulator input edge
00CD
Pulse accumulator overflow
00D0
Timer overflow
00D3
Timer output compare 5/input capture 4
00D6
Timer output compare 4
00D9
Timer output compare 3
00DC
Timer output compare 2
00DF
Timer output compare 1
00E3
Timer input capture 3
00E5
Timer input capture 2
00E8
Timer input capture 1
MC68HC711D3 Data Sheet, Rev. 2.1
22
Freescale Semiconductor
Memory Map
Table 2-2. Bootstrap Mode Jump Vectors (Continued)
Address
Vector
00EB
Real-time interrupt
00EE
IRQ
00F1
XIRQ
00F4
SWI
00F7
Illegal opcode
00FA
COP fail
00FD
Clock monitor
BF00 (Boot)
Reset
2.2.4 Special Test Mode
This special expanded mode is primarily intended or production testing. The user can access a number
of special test control bits in this mode. Reset and interrupt vectors are fetched externally from locations
$BFC0–$BFFF. A switch can be made from this mode to other modes under program control.
2.3 Memory Map
Figure 2-1 illustrates the memory map for both normal modes of operation (single-chip and
expanded-multiplexed), as well as for both special modes of operation (bootstrap and test).
• In the single-chip mode, the MCU does not generate external addresses. The internal memory
locations are shown in the shaded areas, and the contents of these shaded areas are explained
on the right side of the diagram.
• In expanded-multiplexed mode, the memory locations are basically the same as in the single-chip
mode except that the memory locations between shaded areas are for externally addressed
memory and I/O.
• The special bootstrap mode is similar to the single-chip mode, except that the bootstrap program
ROM is located at memory locations $BF00–$BFFF, vectors included.
• The special test mode is similar to the expanded-multiplexed mode except the interrupt vectors are
at external memory locations.
2.3.1 Control and Status Registers
Figure 2-2 is a representation of all 64 bytes of control and status registers, I/O and data registers, and
reserved locations that make up the internal register block. This block may be mapped to any
4-K boundary in memory, but reset locates it at $0000–$003F. This mappability factor and the default
starting addresses are indicated by the use of a bold 0 as the starting character of a register’s address.
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
23
Operating Modes and Memory
$0000
$0000 INTERNAL REGISTERS AND I/O
(MAY BE MAPPED TO ANY 4-K BOUNDARY
$003F USING INIT REGISTER)
$1000
$2000
$0040 192 BYTES STATIC RAM
(MAY BE MAPPED TO ANY 4-K BOUNDARY
$00FF USING THE INIT REGISTER)
$3000
$4000
$5000
$7000 4 KBYTES PROM (ROM)
PRESENT AT RESET AND MAY BE DISABLED BY
$7FFF EPON (ROM ON) BIT IN CONFIG REGISTER.
INTERRUPT VECTORS ARE EXTERNAL.
$6000
$7000
$8000
EXTERNAL
$9000
EXTERNAL
$A000
$B000
$C000
$BF00
$D000
256-BYTES
BOOT ROM
$BFC0
4-KBYTES
PROM (ROM)
$BFC0
$BFFF
$E000
$F000
$BF00
$FFFF
SINGLE
CHIP
EXPANDED
SPECIAL
MULTIPLEXED BOOTSTRAP
MODB
MODA
1
1
0
0
0
1
0
1
SPECIAL
TEST
$BFFF
SPECIAL MODES
INTERRUPT
$BFFF VECTORS
NORMAL MODES
INTERRUPT
$BFFF VECTORS
Mode Selected
Single-chip (mode 0)
Expanded multiplexed (mode 1)
Special bootstrap
Special test
Figure 2-1. MC68HC711D3 Memory Map
MC68HC711D3 Data Sheet, Rev. 2.1
24
Freescale Semiconductor
Memory Map
Addr.
$0000
Register Name
Port A Data Register Read:
(PORTA) Write:
See page 61. Reset:
$0001
Reserved
$0002
Port C Control Register Read:
(PIOC) Write:
See page 63. Reset:
$0003
Port C Data Register Read:
(PORTC) Write:
See page 63. Reset:
$0004
Port B Data Register Read:
(PORTB) Write:
See page 62. Reset:
$0005
$0006
$0007
$0008
$0009
Reserved
Data Direction Register Read:
for Port B (DDRB) Write:
See page 62. Reset:
Data Direction Register Read:
for Port C (DDRC) Write:
See page 63. Reset:
Port D Data Register Read:
(PORTD) Write:
See page 64. Reset:
Data Direction Register Read:
for Port D (DDRD) Write:
See page 64. Reset:
$000A
Reserved
$000B
Timer Compare Force Register Read:
(CFORC) Write:
See page 93. Reset:
$000C
Output Compare 1 Mask Register Read:
(OC1M) Write:
See page 93. Reset:
$000D
Output Compare 1 Data Register Read:
(OC1D) Write:
See page 94. Reset:
Bit 7
6
5
4
3
2
1
Bit 0
PA7
PA6
PA5
PA4
PA3
PA2
PA1
PA0
Hi-Z
0
0
0
Hi-Z
Hi-Z
Hi-Z
Hi-Z
R
R
R
R
R
R
R
R
0
0
CWOM
0
0
0
0
0
0
0
0
0
0
0
0
0
PC7
PC6
PC5
PC4
PC3
PC2
PC1
PC0
BP1
PB0
Reset configures pins as Hi-Z inputs
PB7
PB6
PB5
PB4
PB3
BP2
Reset configures pins as Hi-Z inputs
R
R
R
R
R
R
R
R
DDB7
DDB6
DDB5
DDB4
DDB3
DDB2
DDB1
DDB0
0
0
0
0
0
0
0
0
DDC7
DDC6
DDC5
DDC4
DDC3
DDC2
DDC1
DDC0
0
0
0
0
0
0
0
0
PD7
PD6
PD5
PD4
PD3
PD2
PD1
PD0
0
0
0
0
0
0
0
0
DDD7
DDD6
DDD5
DDD4
DDD3
DDD2
DDD1
DDD0
0
0
0
0
0
0
0
0
R
R
R
R
R
R
R
R
FOC1
FOC2
FOC3
FOC4
FOC5
0
0
0
0
0
0
0
0
0
0
0
OC1M7
OC1M6
OC1M5
OC1M4
OC1M3
0
0
0
0
0
0
0
0
0
0
0
OC1D7
OC1D6
OC1D5
OC1D4
OC1D3
0
0
0
0
0
0
0
0
0
0
0
= Unimplemented
R
= Reserved
U = Unaffected
Figure 2-2. Register and Control Bit Assignments (Sheet 1 of 5)
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
25
Operating Modes and Memory
Addr.
Bit 7
6
5
4
3
2
1
Bit 0
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
0
0
0
0
0
0
0
0
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0
0
0
0
0
0
0
0
Timer Input Capture Register 1 Read:
High (TIC1) Write:
See page 89. Reset:
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 2
Bit 1
Bit 0
$0011
Timer Input Capture Register 1 Read:
Low (TIC1) Write:
See page 89. Reset:
Bit 15
Bit 14
Bit 13
Bit 10
Bit 9
Bit 8
$0012
Timer Input Capture Register 2 Read:
High (TIC2) Write:
See page 89. Reset:
Timer Input Capture Register 2 Read:
Low (TIC2) Write:
See page 89. Reset:
Bit 7
Bit 2
Bit 1
Bit 0
Timer Input Capture Register 3 Read:
High (TIC3) Write:
See page 89. Reset:
Bit 15
Bit 10
Bit 9
Bit 8
Bit 7
Bit 2
Bit 1
Bit 0
$0015
Timer Input Capture Register 3 Read:
Low (TIC3) Write:
See page 89. Reset:
$0016
Timer Output Compare Register 1 Read:
High (TOC1) Write:
See page 92. Reset:
$000E
$000F
$0010
$0013
$0014
$0017
$0018
$0019
Register Name
Timer Counter Register High Read:
(TCNT) Write:
See page 94. Reset:
Timer Counter Register Low Read:
(TCNT) Write:
See page 94. Reset:
Timer Output Compare Register 1 Read:
Low (TOC1) Write:
See page 92. Reset:
Timer Output Compare Register 2 Read:
High (TOC2) Write:
See page 92.
Reset:
Timer Output Compare Register 2 Read:
Low (TOC2) Write:
See page 92.
Reset:
Unaffected by reset
Bit 4
Bit 3
Unaffected by reset
Bit 12
Bit 11
Unaffected by reset
Bit 6
Bit 5
Bit 4
Bit 3
Unaffected by reset
Bit 14
Bit 13
Bit 12
Bit 11
Unaffected by reset
Bit 6
Bit 5
Bit 4
Bit 3
Unaffected by reset
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 15
1
1
1
1
1
1
1
1
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
1
1
1
1
1
1
1
1
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
1
1
1
1
1
1
1
1
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
1
1
1
1
1
1
1
1
= Unimplemented
R
= Reserved
U = Unaffected
Figure 2-2. Register and Control Bit Assignments (Sheet 2 of 5)
MC68HC711D3 Data Sheet, Rev. 2.1
26
Freescale Semiconductor
Memory Map
Addr.
$001A
$001B
$001C
$001D
$001E
$001F
$0020
$0021
$0022
Register Name
Bit 7
6
5
4
3
2
1
Bit 0
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
1
1
1
1
1
1
1
1
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
1
1
1
1
1
1
1
1
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
1
1
1
1
1
1
1
1
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
1
1
1
1
1
1
1
1
Timer Input Capture 4/ Read:
Output Compare 5 Register High Write:
(TI4/O5)
See page 90. Reset:
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
1
1
1
1
1
1
1
1
Timer Input Capture 4/ Read:
Output Compare 5 Register Low Write:
(TI4/O5)
See page 90. Reset:
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
1
1
1
1
1
1
1
1
OM2
OL2
OM3
OL3
OM4
OL4
OM5
OL5
0
0
0
0
0
0
0
0
EDG4B
EDG4A
EDG1B
EDG1A
EDG2B
EDG2A
EDG3B
EDG3A
0
0
0
0
0
0
0
0
OC1I
OC2I
OC3I
OC4I
I4/O5I
IC1I
IC2I
IC3I
0
0
0
0
0
0
0
0
OC1F
OC2F
OC3F
OC4F
I4/O5F
IC1F
IC2F
IC3F
0
0
0
0
0
0
0
0
TOI
RTII
PAOVI
PAII
0
0
PR1
PR0
0
0
0
0
0
0
0
0
TOF
RTIF
PAOVF
PAIF
0
0
0
0
0
0
0
0
0
0
0
0
= Unimplemented
R
Timer Output Compare Register 3 Read:
High (TOC3) Write:
See page 92.
Reset:
Timer Output Compare Register 3 Read:
Low (TOC3) Write:
See page 92.
Reset:
Timer Output Compare Register 4 Read:
High (TOC4) Write:
See page 92.
Reset:
Timer Output Compare Register 4 Read:
Low (TOC4) Write:
See page 92.
Reset:
Timer Control 1 Register Read:
(TCTL1) Write:
See page 95. Reset:
Timer Control Register 2 Read:
(TCTL2) Write:
See page 89. Reset:
Timer Interrupt Mask 1 Register Read:
(TMSK1) Write:
See page 95. Reset:
$0023
Timer Interrupt Flag 1 Register Read:
(TFLG1) Write:
See page 96. Reset:
$0024
Timer Interrupt Mask 2 Register Read:
(TMSK2) Write:
See page 96. Reset:
$0025
Timer Interrupt Flag 2 Register Read:
(TFLG2) Write:
See page 97. Reset:
= Reserved
U = Unaffected
Figure 2-2. Register and Control Bit Assignments (Sheet 3 of 5)
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
27
Operating Modes and Memory
Addr.
$0026
$0027
$0028
Register Name
Pulse Accumulator Control Read:
Register (PACTL) Write:
See pages 99 and 102. Reset:
Pulse Accumulator Count Register Read:
(PACNT) Write:
See page 103. Reset:
SPI Control Register Read:
(SPCR) Write:
See page 81. Reset:
$0029
SPI Status Register Read:
(SPSR) Write:
See page 82. Reset:
$002A
SPI Data I/O Register Read:
(SPDR) Write:
See page 83. Reset:
$002B
$002C
Baud Rate Register Read:
(BAUD) Write:
See page 72. Reset:
SCI Control Register 1 Read:
(SCCR1) Write:
See page 70. Reset:
$002D
SCI Control Register 2 Read:
(SCCR2) Write:
See page 70. Reset:
$002E
SCI Status Register Read:
(SCSR) Write:
See page 71.
Reset:
$002F
$0030
↓
$0038
$0039
SCI Data Register Read:
(SCDR) Write:
See page 69. Reset:
Reserved
System Configuration Options Read:
Register (OPTION) Write:
See page 49. Reset:
Bit 7
6
5
4
3
2
1
Bit 0
DDRA7
PAEN
PAMOD
PEDGE
DDRA3
I4/O5
RTR1
RTR0
0
0
0
0
0
0
0
0
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Unaffected by reset
SPIE
SPE
DWOM
MSTR
CPOL
CPHA
SPR1
SPR0
0
0
0
0
0
1
U
U
SPIF
WCOL
0
MODF
0
0
0
0
0
0
0
0
0
0
0
0
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Unaffected by reset
TCLR
0
SCP1
SCP0
RCKB
SCR2
SCR1
SCR0
0
0
0
0
0
U
U
U
R8
T8
0
M
WAKE
0
0
0
U
U
0
0
0
0
0
0
TIE
TCIE
RIE
ILIE
TE
RE
RWU
SBK
0
0
0
0
0
0
0
0
TDRE
TC
RDRF
IDLE
OR
NF
FE
0
1
1
0
0
0
0
0
0
R7/T7
R6/T6
R5/T5
R4/T4
R3/T3
R2/T2
R1/T1
R0/T0
Unaffected by reset
R
R
R
R
R
R
R
R
0
0
IRQE
DLY
CME
0
CR1
CR0
0
0
0
1
0
0
0
0
= Unimplemented
R
= Reserved
U = Unaffected
Figure 2-2. Register and Control Bit Assignments (Sheet 4 of 5)
MC68HC711D3 Data Sheet, Rev. 2.1
28
Freescale Semiconductor
Memory Map
Addr.
$003A
$003B
$003C
Register Name
Arm/Reset COP Timer Circuitry Read:
Register (COPRST) Write:
See page 48. Reset:
PROM Programming Control Read:
Register (PPROG) Write:
See page 32. Reset:
Highest Priority I-Bit Interrupt and Read:
Miscellaneous Register (HPRIO) Write:
See page 58. Reset:
Bit 7
6
5
4
3
2
1
Bit 0
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0
0
0
0
0
0
0
0
MBE
0
ELAT
EXCOL
EXROW
0
0
PGM
0
0
0
0
0
0
0
0
MDA
IRVNE
PSEL3
PSEL2
PSEL1
PSEL0
0
1
0
1
RBOOT
SMOD
Note 1
1. The values of the RBOOT, SMOD, IRVNE, and MDA bits at reset depend on the mode during initialization. Refer to
Table 4-3. Hardware Mode Select Summary.
$003D
RAM and I/O Mapping Register Read:
(INIT) Write:
See page 29. Reset:
Read:
Test 1 Register
Write:
(TEST)
Reset:
$003E
$003F
System Configuration Register Read:
(CONFIG) Write:
See page 30. Reset:
RAM3
RAM2
RAM1
RAM0
REG3
REG2
REG1
REG0
0
0
0
0
0
0
0
1
TILOP
0
OCC4
CBYP
DISR
FCM
FCOP
0
0
0
0
0
0
0
0
0
0
0
0
0
0
NOCOP
ROMON
0
0
0
0
0
0
U
U
0
= Unimplemented
R
= Reserved
U = Unaffected
Figure 2-2. Register and Control Bit Assignments (Sheet 5 of 5)
2.3.2 RAM and I/O Mapping Register
The random-access memory (RAM) and input/output (I/O) mapping register (INIT) is a special-purpose
8-bit register that is used during initialization to change the default locations of RAM and control registers
within the MCU memory map. It can be written to only once within the first 64 E-clock cycles after a reset
in normal modes. Thereafter, it becomes a read-only register.
Address:
Read:
Write:
Reset:
$003D
Bit 7
6
5
4
3
2
1
Bit 0
RAM3
RAM2
RAM1
RAM0
REG3
REG2
REG1
REG0
0
0
0
0
0
0
0
0
Figure 2-3. RAM and I/O Mapping Register (INIT)
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
29
Operating Modes and Memory
RAM2–RAM0 (INIT bits 7–4) specify the starting address for the 192 bytes of static RAM. REG3–REG0
(INIT bits 3–0) specify the starting address for the control and status register block. In each case, the four
RAM or REG bits become the four upper bits of the 16-bit address of the RAM or register. Since the INIT
register is set to $00 by reset, the internal registers begin at $0000 and RAM begins at $0040.
Throughout this document, control and status register addresses are displayed with the high-order digit
shown as a bold 0. This convention indicates that the register block may be relocated to any 4-K memory
page, but that its default location is $0000.
RAM and the control and status registers can be relocated independently. If the control and status
registers are relocated in such a way as to conflict with PROM, then the register block takes priority, and
the EPROM or OTPROM at those locations becomes inaccessible. No harmful conflicts result. Lower
priority resources simply become inaccessible. Similarly, if an internal resource conflicts with an external
device, no harmful conflict results, since data from the external device is not applied to the internal data
bus. Thus, it cannot interfere with the internal read.
NOTE
There are unused register locations in the 64-byte control and status
register block. Reads of these unused registers return data from the
undriven internal data bus, not from another source that happens to be
located at the same address.
2.3.3 Configuration Control Register
The configuration control register (CONFIG) controls the presence of OTPROM or EPROM in the memory
map and enables the computer operating properly (COP) watchdog system.
This register is writable only once in expanded and single-chip modes (SMOD = 0). In these mode, the
COP watchdog timer is enabled out of reset. In all modes, except normal expanded, EPROM is enabled
and located at $F000–$FFFF. In normal expanded mode, EPROM is enabled and located at
$7000–$7FFF. Should the user wish to be in expanded mode, but with EPROM mapped at
$F000–$FFFF, he must reset in single-chip mode, and write a 1 to the MDA bit in the HPRIO register.
Address: $003F
Read:
Write:
Reset:
Bit 7
6
5
4
3
2
1
Bit 0
0
0
0
0
0
NOCOP
ROMON
0
0
0
0
0
0
U
U
0
U = Unaffected
Figure 2-4. Configuration Control Register (CONFIG)
Bits 7–3 and 0 — Not implemented
Always read 0.
NOCOP — Computer Operating Properly System Disable Bit
This bit is cleared out of reset in normal modes (single chip and expanded), enabling the COP system.
It is writable only once after reset in these modes (SMOD = 0). In the special modes (test and
bootstrap) (SMOD = 1), this bit comes out of reset set, and is writable any time.
1 = COP system is disabled.
0 = COP system is enabled, reset forced on timeout.
MC68HC711D3 Data Sheet, Rev. 2.1
30
Freescale Semiconductor
Programmable Read-Only Memory (PROM)
ROMON — PROM Enable Bit
This bit is set out of reset, enabling the EPROM or OTPROM in all modes. This bit is writable once in
normal modes (SMOD = 0), but is writable at any time in special modes (SMOD = 1).
1 = PROM is present in the memory map.
0 = PROM is disabled from the memory map.
NOTE
In expanded mode out of reset, the EPROM or OTPROM is located at
$7000–$7FFF. In all other modes, the PROM resides at $F000–$FFFF.
2.4 Programmable Read-Only Memory (PROM)
The MC68HC711D3 has 4-Kbytes of one-time programmable read-only memory (OTPROM). The PROM
address is $F000–$FFFF in all modes except expanded multiplexed. In expanded- multiplexed mode, the
PROM is located at $7000–$7FFF after reset.
The on-chip read-only memory (ROM) of an MC68HC711D3 is programmed in MCU mode. In this mode,
the PROM is programmed through the MCU in the bootstrap or test modes. The erased state of a PROM
byte is $FF.
Using the on-chip OTPROM programming feature requires an external 12-volt nominal power supply
(VPP). Normal programming is accomplished using the OTPROM programming register (PPROG).
As described in the following subsections, these two methods of programming and verifying EPROM are
possible:
1. Programming an individual EPROM address
2. Programming the EPROM with downloaded data
2.4.1 Programming an Individual EPROM Address
In this method, the MCU programs its own EPROM by controlling the PPROG register. Use these
procedures to program the EPROM through the MCU with:
• The ROMON bit set in the CONFIG register
• The 12-volt nominal programming voltage present on the XIRQ/VPP pin
• The IRQ pin must be pulled high.
EPROG
LDAB
STAB
#$20
$003B
STAA
LDAB
STAB
$0,X
#$21
$003B
JSR
CLR
DLYEP
$003B
Set ELAT bit (PGM = 0) to enable
EPROM latches.
Store data to EPROM address
Set PGM bit with ELAT = 1 to enable
EPROM programming voltage
Delay 2–4 ms
Turn off programming voltage and set
to READ mode
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
31
Operating Modes and Memory
2.4.2 Programming the EPROM with Downloaded Data
When using this method, the EPROM is programmed by software while in the special test or bootstrap
modes. User-developed software can be uploaded through the SCI or a ROM-resident EPROM
programming utility can be used. The 12-volt nominal programming voltage must be present on the
XIRQ/VPP pin. To use the resident utility, bootload a 3-byte program consisting of a single jump instruction
to $BF00. $BF00 is the starting address of a resident EPROM programming utility. The utility program
sets the X and Y index registers to default values, then receives programming data from an external host,
and puts it in EPROM. The value in IX determines programming delay time. The value in IY is a pointer
to the first address in EPROM to be programmed (default = $F000).
When the utility program is ready to receive programming data, it sends the host the $FF character. Then
it waits. When the host sees the $FF character, the EPROM programming data is sent, starting with the
first location in the EPROM array. After the last byte to be programmed is sent and the corresponding
verification data is returned, the programming operation is terminated by resetting the MCU.
2.4.3 PROM Programming Control Register
The PROM programming control register (PPROG) is used to control the programming of the OTPROM
or EPROM. PPROG is cleared on reset so that the PROM is configured for normal read.
Address: $003B
Read:
Write:
Reset:
Bit 7
6
5
4
3
2
1
Bit 0
MBE
0
ELAT
EXCOL
EXROW
0
0
PGM
0
0
0
0
0
0
0
0
Figure 2-5. PROM Programming Control Register (PPROG)
MBE — Multiple Byte Program Enable Bit
This bit is reserved for testing.
Bit 6, 2, and 1 — Not implemented
Always read 0.
ELAT — EPROM (OTPROM) Latch Control Bit
1 = PROM address and data bus are configured for programming. Writes to PROM cause address
and data to be latched. The PROM cannot be read.
0 = PROM address and data bus are configured for normal reads. PROM cannot be programmed.
EXCOL — Select Extra Columns Bit
This bit is reserved for testing.
EXROW — Select Extra Row Bit
This bit is reserved for testing.
PGM — EPROM (OTPROM) Program Command Bit
This bit may be written only when ELAT = 1.
1 = Programming power is switched on to PROM array.
0 = Programming power is switched off.
MC68HC711D3 Data Sheet, Rev. 2.1
32
Freescale Semiconductor
Chapter 3
Central Processor Unit (CPU)
3.1 Introduction
This section presents information on M68HC11 central processor unit (CPU):
• Architecture
• Data types
• Addressing modes
• Instruction set
• Special operations such as subroutine calls and interrupts
The CPU is designed to treat all peripheral, input/output (I/O), and memory locations identically as
addresses in the 64-Kbyte memory map. This is referred to as memory-mapped I/O. I/O has no
instructions separate from those used by memory. This architecture also allows accessing an operand
from an external memory location with no execution time penalty.
3.2 CPU Registers
M68HC11 CPU registers are an integral part of the CPU and are not addressed as if they were memory
locations. The seven registers, discussed in the following paragraphs, are shown in Figure 3-1.
7
15
ACCUMULATOR A
0 7
ACCUMULATOR B
DOUBLE ACCUMULATOR D
0
0
A:B
D
15
INDEX REGISTER X
0
IX
15
INDEX REGISTER Y
0
IY
15
STACK POINTER
0
SP
0
0
PC
15
PROGRAM COUNTER
7
CONDITION CODE REGISTER
S X H
I
N
Z
V
C
CCR
CARRY
OVERFLOW
ZERO
NEGATIVE
I INTERRUPT MASK
HALF CARRY (FROM BIT 3)
X INTERRUPT MASK
STOP DISABLE
Figure 3-1. Programming Model
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
33
Central Processor Unit (CPU)
3.2.1 Accumulators A, B, and D
Accumulators A and B are general-purpose 8-bit registers that hold operands and results of arithmetic
calculations or data manipulations. For some instructions, these two accumulators are treated as a single
double-byte (16-bit) accumulator called accumulator D. Although most instructions can use accumulators
A or B interchangeably, these exceptions apply:
• The ABX and ABY instructions add the contents of 8-bit accumulator B to the contents of 16-bit
register X or Y, but there are no equivalent instructions that use A instead of B.
• The TAP and TPA instructions transfer data from accumulator A to the condition code register or
from the condition code register to accumulator A. However, there are no equivalent instructions
that use B rather than A.
• The decimal adjust accumulator A (DAA) instruction is used after binary-coded decimal (BCD)
arithmetic operations, but there is no equivalent BCD instruction to adjust accumulator B.
• The add, subtract, and compare instructions associated with both A and B (ABA, SBA, and CBA)
only operate in one direction, making it important to plan ahead to ensure that the correct operand
is in the correct accumulator.
3.2.2 Index Register X (IX)
The IX register provides a 16-bit indexing value that can be added to the 8-bit offset provided in an
instruction to create an effective address. The IX register can also be used as a counter or as a temporary
storage register.
3.2.3 Index Register Y (IY)
The 16-bit IY register performs an indexed mode function similar to that of the IX register. However, most
instructions using the IY register require an extra byte of machine code and an extra cycle of execution
time because of the way the opcode map is implemented. Refer to 3.4 Opcodes and Operands for further
information.
3.2.4 Stack Pointer (SP)
The M68HC11 CPU has an automatic program stack. This stack can be located anywhere in the address
space and can be any size up to the amount of memory available in the system. Normally, the SP is
initialized by one of the first instructions in an application program. The stack is configured as a data
structure that grows downward from high memory to low memory. Each time a new byte is pushed onto
the stack, the SP is decremented. Each time a byte is pulled from the stack, the SP is incremented. At
any given time, the SP holds the 16-bit address of the next free location in the stack. Figure 3-2 is a
summary of SP operations.
When a subroutine is called by a jump-to-subroutine (JSR) or branch-to- subroutine (BSR) instruction, the
address of the instruction after the JSR or BSR is automatically pushed onto the stack, least significant
byte first. When the subroutine is finished, a return-from-subroutine (RTS) instruction is executed. The
RTS pulls the previously stacked return address from the stack and loads it into the program counter.
Execution then continues at this recovered return address.
When an interrupt is recognized, the current instruction finishes normally, the return address (the current
value in the program counter) is pushed onto the stack, all of the CPU registers are pushed onto the stack,
and execution continues at the address specified by the vector for the interrupt.
MC68HC711D3 Data Sheet, Rev. 2.1
34
Freescale Semiconductor
CPU Registers
JSR, JUMP TO SUBROUTINE
MAIN PROGRAM
$9D = JSR
PC
DIRECT
RTN
PC
RTI, RETURN FROM INTERRUPT
INTERRUPT PROGRAM
$3B = RTI
PC
dd
SP+1
CONDITION CODE
NEXT MAIN INSTR
SP+2
ACMLTR B
MAIN PROGRAM
$AD = JSR
SP+3
INDXD,X
ACMLTR A
SP+4 INDEX REGISTER (XH)
SP+5 INDEX REGISTER (XL)
ff
RTN
NEXT MAIN INSTR
PC
MAIN PROGRAM
$18 = PRE
$AD = JSR
INDXD,Y
STACK
SP+6 INDEX REGISTER (YH)
SP-2
SP-1
RTNL
SP+7 INDEX REGISTER (YL)
RTNL
SP+8
SP
RTNH
SP+9
PC
NEXT MAIN INSTR
PC
MAIN PROGRAM
$BD = JSR
MAIN PROGRAM
$6E = JMP
ff
INDXD,X
hh
EXTEND
RTNH
JMP, JUMP
ff
RTN
STACK
SP
ll
RTN
X + ff
NEXT MAIN INSTR
PC
BSR, BRANCH TO SUBROUTINE
MAIN PROGRAM
PC
$8D = BSR
rr
RTN
NEXT MAIN INSTR
RTS, RETURN FROM SUBROUTINE
SUBROUTINE
PC
$39 = RTS
RTNL
SP
RTNH
PC
$3F = SWI
RTN
$3E = WAI
RTN
PC
NEXT INSTRUCTION
MAIN PROGRAM
$7E = JMP
hh
RTNL
SP+2
RTNH
ll
EXTND
hh ll
NEXT INSTRUCTION
STACK
LEGEND:
SP-9
SP-8
CONDITION CODE
SP-7
ACMLTR B
ACMLTR A
SP-5 INDEX REGISTER (XH)
PC
X + ff
STACK
SP-6
WAI, WAIT FOR INTERRUPT
MAIN PROGRAM
ff
INDXD,Y
SP
SP+1
SWI, SOFTWARE INTERRUPT
MAIN PROGRAM
MAIN PROGRAM
$18 = PRE
$6E = JMP
STACK
SP-2
SP-1
NEXT INSTRUCTION
SP-4 INDEX REGISTER (XL)
SP-3 INDEX REGISTER (YH)
SP-2 INDEX REGISTER (YL)
RTNL
SP-1
SP
RTNH
RTN Address of next instruction in main program to be
executed upon return from subroutine
RTNH Most significant byte of return address
RTNL Least significant byte of return address
Shaded cells show stack pointer position after
operation is complete.
dd 8-bit direct address ($0000–$00FF) (high byte
assumed to be $00).
ff 8-bit positive offset $00 (0) to $FF (256) is added
to index.
hh High-order byte of 16-bit extended address.
ll Low-order byte of 16-bit extended address.
rr Signed-relative offset $80 (–128) to $7F (+127)
(offset relative to the address following the
machine code offset byte).
Figure 3-2. Stacking Operations
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
35
Central Processor Unit (CPU)
At the end of the interrupt service routine, a return-from interrupt (RTI) instruction is executed. The RTI
instruction causes the saved registers to be pulled off the stack in reverse order. Program execution
resumes at the return address.
Certain instructions push and pull the A and B accumulators and the X and Y index registers and are often
used to preserve program context. For example, pushing accumulator A onto the stack when entering a
subroutine that uses accumulator A and then pulling accumulator A off the stack just before leaving the
subroutine ensures that the contents of a register will be the same after returning from the subroutine as
it was before starting the subroutine.
3.2.5 Program Counter (PC)
The program counter, a 16-bit register, contains the address of the next instruction to be executed. After
reset, the program counter is initialized from one of six possible vectors, depending on operating mode
and the cause of reset.
See Table 3-1.
Table 3-1. Reset Vector Comparison
Mode
POR or RESET Pin
Clock Monitor
COP Watchdog
Normal
$FFFE, $FFFF
$FFFC, $FFFD
$FFFA, $FFFB
Test or boot
$BFFE, $BFFF
$BFFC, $FFFD
$BFFA, $FFFB
3.2.6 Condition Code Register (CCR)
This 8-bit register contains:
• Five condition code indicators (C, V, Z, N, and H)
• Two interrupt masking bits (IRQ and XIRQ)
• One stop disable bit (S)
In the M68HC11 CPU, condition codes are updated automatically by most instructions. For example, load
accumulator A (LDAA) and store accumulator A (STAA) instructions automatically set or clear the N, Z,
and V condition code flags. Pushes, pulls, add B to X (ABX), add B to Y (ABY), and transfer/exchange
instructions do not affect the condition codes. Refer to Table 3-2, which shows what condition codes are
affected by a particular instruction.
3.2.6.1 Carry/Borrow (C)
The C bit is set if the arithmetic logic unit (ALU) performs a carry or borrow during an arithmetic operation.
The C bit also acts as an error flag for multiply and divide operations. Shift and rotate instructions operate
with and through the carry bit to facilitate multiple-word shift operations.
3.2.6.2 Overflow (V)
The overflow bit is set if an operation causes an arithmetic overflow. Otherwise, the V bit is cleared.
3.2.6.3 Zero (Z)
The Z bit is set if the result of an arithmetic, logic, or data manipulation operation is 0. Otherwise, the Z
bit is cleared. Compare instructions do an internal implied subtraction and the condition codes, including
Z, reflect the results of that subtraction. A few operations (INX, DEX, INY, and DEY) affect the Z bit and
no other condition flags. For these operations, only = and ≠ conditions can be determined.
MC68HC711D3 Data Sheet, Rev. 2.1
36
Freescale Semiconductor
Data Types
3.2.6.4 Negative (N)
The N bit is set if the result of an arithmetic, logic, or data manipulation operation is negative (MSB = 1).
Otherwise, the N bit is cleared. A result is said to be negative if its most significant bit (MSB) is a 1. A quick
way to test whether the contents of a memory location has the MSB set is to load it into an accumulator
and then check the status of the N bit.
3.2.6.5 I-Interrupt Mask (I)
The interrupt request (IRQ) mask (I bit) is a global mask that disables all maskable interrupt sources.
While the I bit is set, interrupts can become pending, but the operation of the CPU continues uninterrupted
until the I bit is cleared. After any reset, the I bit is set by default and can be cleared only by a software
instruction. When an interrupt is recognized, the I bit is set after the registers are stacked, but before the
interrupt vector is fetched. After the interrupt has been serviced, a return-from-interrupt instruction is
normally executed, restoring the registers to the values that were present before the interrupt occurred.
Normally, the I bit is 0 after a return from interrupt is executed. Although the I bit can be cleared within an
interrupt service routine, "nesting" interrupts in this way should be done only when there is a clear
understanding of latency and of the arbitration mechanism. Refer to Chapter 4 Resets, Interrupts, and
Low-Power Modes.
3.2.6.6 Half Carry (H)
The H bit is set when a carry occurs between bits 3 and 4 of the arithmetic logic unit during an ADD, ABA,
or ADC instruction. Otherwise, the H bit is cleared. Half carry is used during BCD operations.
3.2.6.7 X-Interrupt Mask (X)
The XIRQ mask (X) bit disables interrupts from the XIRQ pin. After any reset, X is set by default and must
be cleared by a software instruction. When an XIRQ interrupt is recognized, the X and I bits are set after
the registers are stacked, but before the interrupt vector is fetched. After the interrupt has been serviced,
an RTI instruction is normally executed, causing the registers to be restored to the values that were
present before the interrupt occurred. The X interrupt mask bit is set only by hardware (RESET or XIRQ
acknowledge). X is cleared only by program instruction (TAP, where the associated bit of A is 0; or RTI,
where bit 6 of the value loaded into the CCR from the stack has been cleared). There is no hardware
action for clearing X.
3.2.6.8 STOP Disable (S)
Setting the STOP disable (S) bit prevents the STOP instruction from putting the M68HC11 into a
low-power stop condition. If the STOP instruction is encountered by the CPU while the S bit is set, it is
treated as a no-operation (NOP) instruction, and processing continues to the next instruction. S is set by
reset; STOP is disabled by default.
3.3 Data Types
The M68HC11 CPU supports four data types:
1. Bit data
2. 8-bit and 16-bit signed and unsigned integers
3. 16-bit unsigned fractions
4. 16-bit addresses
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
37
Central Processor Unit (CPU)
A byte is eight bits wide and can be accessed at any byte location. A word is composed of two consecutive
bytes with the most significant byte at the lower value address. Because the M68HC11 is an 8-bit CPU,
there are no special requirements for alignment of instructions or operands.
3.4 Opcodes and Operands
The M68HC11 Family of microcontrollers uses 8-bit opcodes. Each opcode identifies a particular
instruction and associated addressing mode to the CPU. Several opcodes are required to provide each
instruction with a range of addressing capabilities. Only 256 opcodes would be available if the range of
values were restricted to the number able to be expressed in 8-bit binary numbers.
A 4-page opcode map has been implemented to expand the number of instructions. An additional byte,
called a prebyte, directs the processor from page 0 of the opcode map to one of the other three pages.
As its name implies, the additional byte precedes the opcode.
A complete instruction consists of a prebyte, if any, an opcode, and zero, one, two, or three operands.
The operands contain information the CPU needs for executing the instruction. Complete instructions can
be from one to five bytes long.
3.5 Addressing Modes
Six addressing modes can be used to access memory:
1. Immediate
2. Direct
3. Extended
4. Indexed
5. Inherent
6. Relative
These modes are detailed in the following paragraphs. All modes except inherent mode use an effective
address. The effective address is the memory address from which the argument is fetched or stored or
the address from which execution is to proceed. The effective address can be specified within an
instruction, or it can be calculated.
3.5.1 Immediate
In the immediate addressing mode, an argument is contained in the byte(s) immediately following the
opcode. The number of bytes following the opcode matches the size of the register or memory location
being operated on. There are 2-, 3-, and 4- (if prebyte is required) byte immediate instructions. The
effective address is the address of the byte following the instruction.
3.5.2 Direct
In the direct addressing mode, the low-order byte of the operand address is contained in a single byte
following the opcode, and the high-order byte of the address is assumed to be $00. Addresses $00–$FF
are thus accessed directly, using 2-byte instructions. Execution time is reduced by eliminating the
additional memory access required for the high-order address byte. In most applications, this
256-byte area is reserved for frequently referenced data. In M68HC11 MCUs, the memory map can be
configured for combinations of internal registers, RAM, or external memory to occupy these addresses.
MC68HC711D3 Data Sheet, Rev. 2.1
38
Freescale Semiconductor
Instruction Set
3.5.3 Extended
In the extended addressing mode, the effective address of the argument is contained in two bytes
following the opcode byte. These are 3-byte instructions (or 4-byte instructions if a prebyte is required).
One or two bytes are needed for the opcode and two for the effective address.
3.5.4 Indexed
In the indexed addressing mode, an 8-bit unsigned offset contained in the instruction is added to the value
contained in an index register (IX or IY). The sum is the effective address. This addressing mode allows
referencing any memory location in the 64-Kbyte address space. These are 2- to 5-byte instructions,
depending on whether a prebyte is required.
3.5.5 Inherent
In the inherent addressing mode, all the information necessary to execute the instruction is contained in
the opcode. Operations that use only the index registers or accumulators, as well as control instructions
with no arguments, are included in this addressing mode. These are 1- or 2-byte instructions.
3.5.6 Relative
The relative addressing mode is used only for branch instructions. If the branch condition is true, an 8-bit
signed offset included in the instruction is added to the contents of the program counter to form the
effective branch address. Otherwise, control proceeds to the next instruction. These are usually 2-byte
instructions.
3.6 Instruction Set
Refer to Table 3-2, which shows all the M68HC11 instructions in all possible addressing modes. For each
instruction, the table shows the operand construction, the number of machine code bytes, and execution
time in CPU E-clock cycles.
Table 3-2. Instruction Set (Sheet 1 of 8)
Mnemonic
Operation
Description
ABA
Add
Accumulators
ABX
ABY
ADCA (opr)
ADCB (opr)
ADDA (opr)
Addressing
Instruction
Mode
Opcode
A+B⇒A
INH
Add B to X
IX + (00 : B) ⇒ IX
INH
Add B to Y
IY + (00 : B) ⇒ IY
INH
Add with Carry
to A
A+M+C⇒A
Add with Carry
to B
Add Memory to
A
B+M+C⇒B
A+M⇒A
A
A
A
A
A
IMM
DIR
EXT
IND,X
IND,Y
B
B
B
B
B
IMM
DIR
EXT
IND,X
IND,Y
A
A
A
A
A
IMM
DIR
EXT
IND,X
IND,Y
Condition Codes
Operand
Cycles
S
X
H
I
N
Z
V
C
1B
—
2
—
—
∆
—
∆
∆
∆
∆
3A
—
3
—
—
—
—
—
—
—
—
18
3A
—
4
—
—
—
—
—
—
—
—
ii
dd
hh
ff
ff
—
∆
—
∆
∆
∆
∆
ll
2
3
4
4
5
—
18
89
99
B9
A9
A9
ii
dd
hh
ff
ff
—
∆
—
∆
∆
∆
∆
ll
2
3
4
4
5
—
18
C9
D9
F9
E9
E9
ii
dd
hh
ff
ff
—
∆
—
∆
∆
∆
∆
ll
2
3
4
4
5
—
18
8B
9B
BB
AB
AB
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
39
Central Processor Unit (CPU)
Table 3-2. Instruction Set (Sheet 2 of 8)
Mnemonic
Operation
Description
ADDB (opr)
Add Memory to
B
B+M⇒B
ADDD (opr)
ANDA (opr)
ANDB (opr)
ASL (opr)
Add 16-Bit to D
B•M⇒B
AND B with
Memory
Arithmetic Shift
Left
b7
b0
b7
A
A
A
A
A
IMM
DIR
EXT
IND,X
IND,Y
B
B
B
B
B
IMM
DIR
EXT
IND,X
IND,Y
EXT
IND,X
IND,Y
Instruction
Opcode
Operand
18
CB
DB
FB
EB
EB
ii
dd
hh
ff
ff
18
C3
D3
F3
E3
E3
jj
dd
hh
ff
ff
18
84
94
B4
A4
A4
ii
dd
hh
ff
ff
18
C4
D4
F4
E4
E4
ii
dd
hh
ff
ff
18
78
68
68
hh
ff
ff
Condition Codes
Cycles
S
X
H
I
N
Z
V
C
2
3
4
4
5
—
—
∆
—
∆
∆
∆
∆
—
—
—
—
∆
∆
∆
∆
ll
4
5
6
6
7
—
—
—
—
∆
∆
0
—
ll
2
3
4
4
5
—
—
—
—
∆
∆
0
—
ll
2
3
4
4
5
6
6
7
—
—
—
—
∆
∆
∆
∆
ll
kk
ll
A
INH
48
—
2
—
—
—
—
∆
∆
∆
∆
B
INH
58
—
2
—
—
—
—
∆
∆
∆
∆
INH
05
—
3
—
—
—
—
∆
∆
∆
∆
EXT
IND,X
IND,Y
77
67
67
6
6
7
—
—
—
—
∆
∆
∆
∆
0
b0
Arithmetic Shift
Left B
b7
IMM
DIR
EXT
IND,X
IND,Y
IMM
DIR
EXT
IND,X
IND,Y
0
Arithmetic Shift
Left A
C
ASLD
B
B
B
B
B
A•M⇒A
AND A with
Memory
C
ASLB
Mode
D + (M : M + 1) ⇒ D
C
ASLA
Addressing
0
b0
Arithmetic Shift
Left D
0
C b7 A b0 b7 B b0
ASR
Arithmetic Shift
Right
ASRA
Arithmetic Shift
Right A
ASRB
Arithmetic Shift
Right B
BCC (rel)
Branch if Carry
Clear
?C=0
BCLR (opr)
(msk)
Clear Bit(s)
M • (mm) ⇒ M
BCS (rel)
Branch if Carry
Set
?C=1
BEQ (rel)
Branch if = Zero
?Z=1
BGE (rel)
Branch if ∆ Zero
?N⊕V=0
BGT (rel)
Branch if > Zero
? Z + (N ⊕ V) = 0
BHI (rel)
Branch if
Higher
BHS (rel)
BITA (opr)
b7
b0
C
18
hh
ff
ff
ll
A
INH
47
—
2
—
—
—
—
∆
∆
∆
∆
B
INH
57
—
2
—
—
—
—
∆
∆
∆
∆
REL
24
rr
3
—
—
—
—
—
—
—
—
DIR
IND,X
IND,Y
15
1D
1D
dd
ff
ff
6
7
8
—
—
—
—
∆
∆
0
—
25
rr
3
—
—
—
—
—
—
—
—
REL
27
rr
3
—
—
—
—
—
—
—
—
REL
2C
rr
3
—
—
—
—
—
—
—
—
REL
2E
rr
3
—
—
—
—
—
—
—
—
?C+Z=0
REL
22
rr
3
—
—
—
—
—
—
—
—
Branch if
Higher or Same
?C=0
REL
24
rr
3
—
—
—
—
—
—
—
—
Bit(s) Test A
with Memory
A•M
IMM
DIR
EXT
IND,X
IND,Y
85
95
B5
A5
A5
ii
dd
hh
ff
ff
2
3
4
4
5
—
—
—
—
∆
∆
0
—
b7
b7
b0
b0
C
C
18
REL
A
A
A
A
A
18
mm
mm
mm
ll
MC68HC711D3 Data Sheet, Rev. 2.1
40
Freescale Semiconductor
Instruction Set
Table 3-2. Instruction Set (Sheet 3 of 8)
Mnemonic
Operation
Description
BITB (opr)
Bit(s) Test B
with Memory
B•M
Addressing
Mode
B
B
B
B
B
IMM
DIR
EXT
IND,X
IND,Y
Instruction
Opcode
18
Operand
C5
D5
F5
E5
E5
ii
dd
hh
ff
ff
Condition Codes
Cycles
S
X
H
I
N
Z
V
C
2
3
4
4
5
—
—
—
—
∆
∆
0
—
ll
BLE (rel)
Branch if ∆ Zero
? Z + (N ⊕ V) = 1
REL
2F
rr
3
—
—
—
—
—
—
—
—
BLO (rel)
Branch if Lower
?C=1
REL
25
rr
3
—
—
—
—
—
—
—
—
BLS (rel)
Branch if Lower
or Same
?C+Z=1
REL
23
rr
3
—
—
—
—
—
—
—
—
BLT (rel)
Branch if < Zero
?N⊕V=1
REL
2D
rr
3
—
—
—
—
—
—
—
—
BMI (rel)
Branch if Minus
?N=1
REL
2B
rr
3
—
—
—
—
—
—
—
—
BNE (rel)
Branch if not =
Zero
?Z=0
REL
26
rr
3
—
—
—
—
—
—
—
—
BPL (rel)
Branch if Plus
?N=0
REL
2A
rr
3
—
—
—
—
—
—
—
—
BRA (rel)
Branch Always
?1=1
REL
20
rr
3
—
—
—
—
—
—
—
—
BRCLR(opr)
(msk)
(rel)
Branch if
Bit(s) Clear
? M • mm = 0
DIR
IND,X
IND,Y
13
1F
1F
dd
rr
ff
rr
ff
rr
6
7
8
—
—
—
—
—
—
—
—
3
—
—
—
—
—
—
—
—
6
7
8
—
—
—
—
—
—
—
—
6
7
8
—
—
—
—
∆
∆
0
—
BRN (rel)
Branch Never
?1=0
BRSET(opr)
(msk)
(rel)
Branch if Bit(s)
Set
? (M) • mm = 0
18
mm
mm
mm
REL
21
rr
DIR
IND,X
IND,Y
12
1E
1E
dd
rr
ff
rr
ff
rr
mm
14
1C
1C
dd
ff
ff
mm
mm
mm
18
mm
mm
BSET (opr)
(msk)
Set Bit(s)
M + mm ⇒ M
DIR
IND,X
IND,Y
BSR (rel)
Branch to
Subroutine
See Figure 3-2
REL
8D
rr
6
—
—
—
—
—
—
—
—
BVC (rel)
Branch if
Overflow Clear
?V=0
REL
28
rr
3
—
—
—
—
—
—
—
—
BVS (rel)
Branch if
Overflow Set
?V=1
REL
29
rr
3
—
—
—
—
—
—
—
—
CBA
Compare A to B
A–B
INH
11
—
2
—
—
—
—
∆
∆
∆
∆
CLC
Clear Carry Bit
0⇒C
INH
0C
—
2
—
—
—
—
—
—
—
0
CLI
Clear Interrupt
Mask
0⇒I
INH
0E
—
2
—
—
—
0
—
—
—
—
CLR (opr)
Clear Memory
Byte
0⇒M
EXT
IND,X
IND,Y
7F
6F
6F
6
6
7
—
—
—
—
0
1
0
0
CLRA
Clear
Accumulator A
0⇒A
A
INH
4F
—
2
—
—
—
—
0
1
0
0
CLRB
Clear
Accumulator B
0⇒B
B
INH
5F
—
2
—
—
—
—
0
1
0
0
CLV
Clear Overflow
Flag
0⇒V
INH
0A
—
2
—
—
—
—
—
—
0
—
CMPA (opr)
Compare A to
Memory
A–M
A
A
A
A
A
IMM
DIR
EXT
IND,X
IND,Y
ii
dd
hh
ff
ff
—
—
—
∆
∆
∆
∆
ll
2
3
4
4
5
—
18
81
91
B1
A1
A1
B
B
B
B
B
IMM
DIR
EXT
IND,X
IND,Y
ii
dd
hh
ff
ff
—
—
—
∆
∆
∆
∆
ll
2
3
4
4
5
—
18
C1
D1
F1
E1
E1
hh
ff
ff
6
6
7
—
—
—
—
∆
∆
0
1
18
73
63
63
CMPB (opr)
COM (opr)
Compare B to
Memory
Ones
Complement
Memory Byte
B–M
$FF – M ⇒ M
EXT
IND,X
IND,Y
18
18
hh
ff
ff
ll
ll
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
41
Central Processor Unit (CPU)
Table 3-2. Instruction Set (Sheet 4 of 8)
Mnemonic
Operation
Description
COMA
Ones
Complement
A
$FF – A ⇒ A
COMB
Ones
Complement
B
$FF – B ⇒ B
CPD (opr)
Compare D to
Memory 16-Bit
D–M:M +1
CPX (opr)
CPY (opr)
Compare X to
Memory 16-Bit
Compare Y to
Memory 16-Bit
Addressing
Instruction
Mode
Opcode
A
INH
B
INH
IMM
DIR
EXT
IND,X
IND,Y
IX – M : M + 1
IY – M : M + 1
Condition Codes
Operand
Cycles
S
X
H
I
N
Z
V
C
43
—
2
—
—
—
—
∆
∆
0
1
53
—
2
—
—
—
—
∆
∆
0
1
5
6
7
7
7
—
—
—
—
∆
∆
∆
∆
4
5
6
6
7
—
—
—
—
∆
∆
∆
∆
5
6
7
7
7
—
—
—
—
∆
∆
∆
∆
2
—
—
—
—
∆
∆
∆
∆
6
6
7
—
—
—
—
∆
∆
∆
—
1A
1A
1A
1A
CD
83
93
B3
A3
A3
jj
dd
hh
ff
ff
kk
IMM
DIR
EXT
IND,X
IND,Y
jj
dd
hh
ff
ff
kk
CD
8C
9C
BC
AC
AC
IMM
DIR
EXT
IND,X
IND,Y
18
18
18
1A
18
8C
9C
BC
AC
AC
jj
dd
hh
ff
ff
kk
Adjust Sum to BCD
DEC (opr)
Decrement
Memory Byte
M–1⇒M
DECA
Decrement
Accumulator
A
A–1⇒A
A
INH
4A
—
2
—
—
—
—
∆
∆
∆
—
DECB
Decrement
Accumulator
B
B–1⇒B
B
INH
5A
—
2
—
—
—
—
∆
∆
∆
—
DES
Decrement
Stack Pointer
SP – 1 ⇒ SP
INH
34
—
3
—
—
—
—
—
—
—
—
DEX
Decrement
Index Register
X
IX – 1 ⇒ IX
INH
09
—
3
—
—
—
—
—
∆
—
—
DEY
Decrement
Index Register
Y
IY – 1 ⇒ IY
INH
18
09
—
4
—
—
—
—
—
∆
—
—
EORA (opr)
Exclusive OR A
with Memory
A⊕M⇒A
ii
dd
hh
ff
ff
—
—
—
∆
∆
0
—
ll
2
3
4
4
5
—
18
88
98
B8
A8
A8
ii
dd
hh
ff
ff
—
—
—
∆
∆
0
—
ll
2
3
4
4
5
—
18
C8
D8
F8
E8
E8
B⊕M⇒B
EXT
IND,X
IND,Y
7A
6A
6A
ll
Decimal Adjust
A
Exclusive OR B
with Memory
19
ll
DAA
EORB (opr)
INH
ll
A
A
A
A
A
IMM
DIR
EXT
IND,X
IND,Y
B
B
B
B
B
IMM
DIR
EXT
IND,X
IND,Y
18
—
hh
ff
ff
ll
FDIV
Fractional
Divide 16 by 16
D / IX ⇒ IX; r ⇒ D
INH
03
—
41
—
—
—
—
—
∆
∆
∆
IDIV
Integer Divide
16 by 16
D / IX ⇒ IX; r ⇒ D
INH
02
—
41
—
—
—
—
—
∆
0
∆
INC (opr)
Increment
Memory Byte
M+1⇒M
EXT
IND,X
IND,Y
7C
6C
6C
6
6
7
—
—
—
—
∆
∆
∆
—
INCA
Increment
Accumulator
A
A+1⇒A
A
INH
4C
—
2
—
—
—
—
∆
∆
∆
—
INCB
Increment
Accumulator
B
B+1⇒B
B
INH
5C
—
2
—
—
—
—
∆
∆
∆
—
INS
Increment
Stack Pointer
SP + 1 ⇒ SP
INH
31
—
3
—
—
—
—
—
—
—
—
18
hh
ff
ff
ll
MC68HC711D3 Data Sheet, Rev. 2.1
42
Freescale Semiconductor
Instruction Set
Table 3-2. Instruction Set (Sheet 5 of 8)
Mnemonic
Operation
Description
INX
Increment
Index Register
X
INY
Addressing
Instruction
Mode
Opcode
IX + 1 ⇒ IX
INH
Increment
Index Register
Y
IY + 1 ⇒ IY
INH
JMP (opr)
Jump
See Figure 3-2
EXT
IND,X
IND,Y
JSR (opr)
Jump to
Subroutine
See Figure 3-2
DIR
EXT
IND,X
IND,Y
Load
Accumulator
A
M⇒A
Load
Accumulator
B
M⇒B
Load Double
Accumulator
D
M ⇒ A,M + 1 ⇒ B
Load Stack
Pointer
M : M + 1 ⇒ SP
LDAA (opr)
LDAB (opr)
LDD (opr)
LDS (opr)
LDX (opr)
LDY (opr)
LSL (opr)
Load Index
Register
X
M : M + 1 ⇒ IX
Load Index
Register
Y
M : M + 1 ⇒ IY
Logical Shift
Left
C
LSLA
Logical Shift
Left A
LSLB
Logical Shift
Left B
C
C
LSLD
LSRA
LSRB
b7
b7
b0
b0
b0
Logical Shift
Right
Logical Shift
Right A
Logical Shift
Right B
0
0
b7
b7
b7
B
B
B
B
B
IMM
DIR
EXT
IND,X
IND,Y
IMM
DIR
EXT
IND,X
IND,Y
IMM
DIR
EXT
IND,X
IND,Y
Cycles
S
X
H
I
N
Z
V
C
08
—
3
—
—
—
—
—
∆
—
—
18
08
—
4
—
—
—
—
—
∆
—
—
hh
ff
ff
3
3
4
—
—
—
—
—
—
—
—
18
7E
6E
6E
dd
hh
ff
ff
5
6
6
7
—
—
—
—
—
—
—
—
18
9D
BD
AD
AD
ii
dd
hh
ff
ff
—
—
—
∆
∆
0
—
ll
2
3
4
4
5
—
18
86
96
B6
A6
A6
ii
dd
hh
ff
ff
—
—
—
∆
∆
0
—
ll
2
3
4
4
5
—
18
C6
D6
F6
E6
E6
jj
dd
hh
ff
ff
kk
3
4
5
5
6
—
—
—
—
∆
∆
0
—
18
CC
DC
FC
EC
EC
jj
dd
hh
ff
ff
kk
3
4
5
5
6
—
—
—
—
∆
∆
0
—
3
4
5
5
6
—
—
—
—
∆
∆
0
—
4
5
6
6
6
—
—
—
—
∆
∆
0
—
6
6
7
—
—
—
—
∆
∆
∆
∆
ll
ll
ll
18
8E
9E
BE
AE
AE
IMM
DIR
EXT
IND,X
IND,Y
jj
dd
hh
ff
ff
kk
CD
CE
DE
FE
EE
EE
IMM
DIR
EXT
IND,X
IND,Y
18
18
18
1A
18
CE
DE
FE
EE
EE
jj
dd
hh
ff
ff
kk
hh
ff
ff
ll
18
78
68
68
EXT
IND,X
IND,Y
ll
ll
ll
A
INH
48
—
2
—
—
—
—
∆
∆
∆
∆
B
INH
58
—
2
—
—
—
—
∆
∆
∆
∆
INH
05
—
3
—
—
—
—
∆
∆
∆
∆
EXT
IND,X
IND,Y
74
64
64
6
6
7
—
—
—
—
0
∆
∆
∆
0
0
b7 A b0 b7 B b0
0
IMM
DIR
EXT
IND,X
IND,Y
0
Logical Shift
Left Double
C
LSR (opr)
b7
A
A
A
A
A
Condition Codes
Operand
0
b0 C
18
hh
ff
ff
ll
A
INH
44
—
2
—
—
—
—
0
∆
∆
∆
B
INH
54
—
2
—
—
—
—
0
∆
∆
∆
b0 C
b0 C
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
43
Central Processor Unit (CPU)
Table 3-2. Instruction Set (Sheet 6 of 8)
Mnemonic
Operation
LSRD
Logical Shift
Right Double
Addressing
Description
0
Instruction
Mode
Opcode
INH
04
Condition Codes
Operand
Cycles
S
X
H
I
N
Z
V
C
—
3
—
—
—
—
0
∆
∆
∆
—
10
—
—
—
—
—
—
—
∆
6
6
7
—
—
—
—
∆
∆
∆
∆
b7 A b0 b7 B b0 C
MUL
Multiply 8 by 8
A∗B⇒D
INH
3D
NEG (opr)
Two’s
Complement
Memory Byte
0–M⇒M
EXT
IND,X
IND,Y
70
60
60
NEGA
Two’s
Complement
A
0–A⇒A
A
INH
40
—
2
—
—
—
—
∆
∆
∆
∆
NEGB
Two’s
Complement
B
0–B⇒B
B
INH
50
—
2
—
—
—
—
∆
∆
∆
∆
NOP
No operation
No Operation
—
2
—
—
—
—
—
—
—
—
ORAA (opr)
OR
Accumulator
A (Inclusive)
A+M⇒A
—
—
—
—
∆
∆
0
—
ll
2
3
4
4
5
OR
Accumulator
B (Inclusive)
B+M⇒B
—
—
—
—
∆
∆
0
—
ll
2
3
4
4
5
ORAB (opr)
18
hh
ff
ff
INH
01
A
A
A
A
A
IMM
DIR
EXT
IND,X
IND,Y
18
8A
9A
BA
AA
AA
ii
dd
hh
ff
ff
B
B
B
B
B
IMM
DIR
EXT
IND,X
IND,Y
18
CA
DA
FA
EA
EA
ii
dd
hh
ff
ff
ll
PSHA
Push A onto
Stack
A ⇒ Stk,SP = SP – 1 A
INH
36
—
3
—
—
—
—
—
—
—
—
PSHB
Push B onto
Stack
B ⇒ Stk,SP = SP – 1 B
INH
37
—
3
—
—
—
—
—
—
—
—
PSHX
Push X onto
Stack (Lo
First)
IX ⇒ Stk,SP = SP – 2
INH
3C
—
4
—
—
—
—
—
—
—
—
PSHY
Push Y onto
Stack (Lo
First)
IY ⇒ Stk,SP = SP – 2
INH
3C
—
5
—
—
—
—
—
—
—
—
PULA
Pull A from
Stack
SP = SP + 1, A ⇐ Stk A
INH
32
—
4
—
—
—
—
—
—
—
—
PULB
Pull B from
Stack
SP = SP + 1, B ⇐ Stk B
INH
33
—
4
—
—
—
—
—
—
—
—
PULX
Pull X From
Stack (Hi
First)
SP = SP + 2, IX ⇐ Stk
INH
38
—
5
—
—
—
—
—
—
—
—
PULY
Pull Y from
Stack (Hi
First)
SP = SP + 2, IY ⇐ Stk
INH
18
38
—
6
—
—
—
—
—
—
—
—
ROL (opr)
Rotate Left
6
6
7
—
—
—
—
∆
∆
∆
∆
18
79
69
69
ROLA
Rotate Left A
ROLB
Rotate Left B
ROR (opr)
Rotate Right
RORA
Rotate Right A
RORB
Rotate Right B
RTI
Return from
Interrupt
C
C
C
b7
b7
b7
b7
b7
b7
EXT
IND,X
IND,Y
b0
18
hh
ff
ff
ll
A
INH
49
—
2
—
—
—
—
∆
∆
∆
∆
B
INH
59
—
2
—
—
—
—
∆
∆
∆
∆
EXT
IND,X
IND,Y
76
66
66
6
6
7
—
—
—
—
∆
∆
∆
∆
b0
b0
b0 C
18
hh
ff
ff
ll
A
INH
46
—
2
—
—
—
—
∆
∆
∆
∆
B
INH
56
—
2
—
—
—
—
∆
∆
∆
∆
INH
3B
—
12
∆
↓
∆
∆
∆
∆
∆
∆
b0 C
b0 C
See Figure 3-2
MC68HC711D3 Data Sheet, Rev. 2.1
44
Freescale Semiconductor
Instruction Set
Table 3-2. Instruction Set (Sheet 7 of 8)
Mnemonic
Operation
Description
RTS
Return from
Subroutine
SBA
SBCA (opr)
SBCB (opr)
Addressing
Instruction
Mode
Opcode
See Figure 3-2
INH
Subtract B from
A
A–B⇒A
Subtract with
Carry from A
A–M–C⇒A
Subtract with
Carry from B
B–M–C⇒B
Condition Codes
Operand
Cycles
S
X
H
I
N
Z
V
C
39
—
5
—
—
—
—
—
—
—
—
INH
10
—
2
—
—
—
—
∆
∆
∆
∆
A
A
A
A
A
IMM
DIR
EXT
IND,X
IND,Y
ii
dd
hh
ff
ff
—
—
—
∆
∆
∆
∆
ll
2
3
4
4
5
—
18
82
92
B2
A2
A2
B
B
B
B
B
IMM
DIR
EXT
IND,X
IND,Y
ii
dd
hh
ff
ff
—
—
—
∆
∆
∆
∆
ll
2
3
4
4
5
—
18
C2
D2
F2
E2
E2
SEC
Set Carry
1⇒C
INH
0D
—
2
—
—
—
—
—
—
—
1
SEI
Set Interrupt
Mask
1⇒I
INH
0F
—
2
—
—
—
1
—
—
—
—
SEV
Set Overflow
Flag
1⇒V
INH
0B
—
2
—
—
—
—
—
—
1
—
STAA (opr)
Store
Accumulator
A
A⇒M
A
A
A
A
DIR
EXT
IND,X
IND,Y
dd
hh
ff
ff
3
4
4
5
—
—
—
—
∆
∆
0
—
18
97
B7
A7
A7
Store
Accumulator
B
B⇒M
B
B
B
B
DIR
EXT
IND,X
IND,Y
dd
hh
ff
ff
3
4
4
5
—
—
—
—
∆
∆
0
—
18
D7
F7
E7
E7
Store
Accumulator
D
A ⇒ M, B ⇒ M + 1
dd
hh
ff
ff
4
5
5
6
—
—
—
—
∆
∆
0
—
18
DD
FD
ED
ED
STOP
Stop Internal
Clocks
—
2
—
—
—
—
—
—
—
—
STS (opr)
Store Stack
Pointer
SP ⇒ M : M + 1
4
5
5
6
—
—
—
—
∆
∆
0
—
Store Index
Register X
IX ⇒ M : M + 1
4
5
5
6
—
—
—
—
∆
∆
0
—
Store Index
Register Y
IY ⇒ M : M + 1
5
6
6
6
—
—
—
—
∆
∆
0
—
Subtract
Memory from
A
A–M⇒A
—
—
—
—
∆
∆
∆
∆
ll
2
3
4
4
5
Subtract
Memory from
B
B–M⇒B
—
—
—
—
∆
∆
∆
∆
ll
2
3
4
4
5
Subtract
Memory from
D
D–M:M+1⇒D
4
5
6
6
7
—
—
—
—
∆
∆
∆
∆
SWI
Software
Interrupt
See Figure 3-2
14
—
—
—
1
—
—
—
—
TAB
Transfer A to B
A⇒B
INH
16
—
2
—
—
—
—
∆
∆
0
—
TAP
Transfer A to
CC Register
A ⇒ CCR
INH
06
—
2
∆
↓
∆
∆
∆
∆
∆
∆
STAB (opr)
STD (opr)
STX (opr)
STY (opr)
SUBA (opr)
SUBB (opr)
SUBD (opr)
DIR
EXT
IND,X
IND,Y
INH
CF
DIR
EXT
IND,X
IND,Y
dd
hh
ff
ff
18
DIR
EXT
IND,X
IND,Y
CD
DF
FF
EF
EF
dd
hh
ff
ff
DIR
EXT
IND,X
IND,Y
18
18
1A
18
DF
FF
EF
EF
dd
hh
ff
ff
18
80
90
B0
A0
A0
ii
dd
hh
ff
ff
18
C0
D0
F0
E0
E0
ii
dd
hh
ff
ff
18
83
93
B3
A3
A3
jj
dd
hh
ff
ff
IMM
DIR
EXT
IND,X
IND,Y
A
A
A
A
A
IMM
DIR
EXT
IND,X
IND,Y
IMM
DIR
EXT
IND,X
IND,Y
INH
3F
ll
ll
—
9F
BF
AF
AF
A
A
A
A
A
ll
ll
ll
ll
kk
ll
—
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
45
Central Processor Unit (CPU)
Table 3-2. Instruction Set (Sheet 8 of 8)
Mnemonic
Operation
Description
TBA
Transfer B to A
TEST
Addressing
Instruction
Mode
Opcode
B⇒A
INH
TEST (Only in
Test Modes)
Address Bus Counts
TPA
Transfer CC
Register to A
CCR ⇒ A
TST (opr)
Test for Zero or
Minus
M–0
TSTA
Test A for Zero
or Minus
A–0
A
INH
4D
TSTB
Test B for Zero
or Minus
B–0
B
INH
TSX
Transfer Stack
Pointer to X
SP + 1 ⇒ IX
INH
TSY
Transfer Stack
Pointer to Y
SP + 1 ⇒ IY
INH
TXS
Transfer X to
Stack Pointer
IX – 1 ⇒ SP
INH
TYS
Transfer Y to
Stack Pointer
IY – 1 ⇒ SP
INH
WAI
Wait for
Interrupt
Stack Regs & WAIT
XGDX
Exchange D
with X
XGDY
Exchange D
with Y
Cycle
*
**
Condition Codes
Operand
Cycles
S
X
H
I
N
Z
V
C
17
—
2
—
—
—
—
∆
∆
0
—
INH
00
—
*
—
—
—
—
—
—
—
—
INH
07
—
2
—
—
—
—
—
—
—
—
EXT
IND,X
IND,Y
7D
6D
6D
6
6
7
—
—
—
—
∆
∆
0
0
—
2
—
—
—
—
∆
∆
0
0
5D
—
2
—
—
—
—
∆
∆
0
0
30
—
3
—
—
—
—
—
—
—
—
30
—
4
—
—
—
—
—
—
—
—
35
—
3
—
—
—
—
—
—
—
—
35
—
4
—
—
—
—
—
—
—
—
INH
3E
—
**
—
—
—
—
—
—
—
—
IX ⇒ D, D ⇒ IX
INH
8F
—
3
—
—
—
—
—
—
—
—
IY ⇒ D, D ⇒ IY
INH
8F
—
4
—
—
—
—
—
—
—
—
18
18
18
18
hh
ff
ff
ll
Infinity or until reset occurs
12 cycles are used beginning with the opcode fetch. A wait state is entered which remains in effect for an integer number of MPU E-clock
cycles (n) until an interrupt is recognized. Finally, two additional cycles are used to fetch the appropriate interrupt vector (14 + n total).
Operands
dd
= 8-bit direct address ($0000–$00FF) (high byte assumed to be $00)
ff
= 8-bit positive offset $00 (0) to $FF (255) (is added to index)
hh
= High-order byte of 16-bit extended address
ii
= One byte of immediate data
jj
= High-order byte of 16-bit immediate data
kk
= Low-order byte of 16-bit immediate data
ll
= Low-order byte of 16-bit extended address
mm = 8-bit mask (set bits to be affected)
rr
= Signed relative offset $80 (–128) to $7F (+127)
(offset relative to address following machine code offset byte)
Operators
()
Contents of register shown inside parentheses
⇐
Is transferred to
⇑
Is pulled from stack
Is pushed onto stack
⇓
•
Boolean AND
+
Arithmetic addition symbol except where used as inclusive-OR symbol
in Boolean formula
⊕
Exclusive-OR
∗
Multiply
:
Concatenation
–
Arithmetic subtraction symbol or negation symbol (two’s complement)
Condition Codes
—
Bit not changed
0
Bit always cleared
1
Bit always set
∆
Bit cleared or set, depending on operation
↓
Bit can be cleared, cannot become set
MC68HC711D3 Data Sheet, Rev. 2.1
46
Freescale Semiconductor
Chapter 4
Resets, Interrupts, and Low-Power Modes
4.1 Introduction
This section describes the internal and external resets and interrupts of the MC68HC711D3 and its two
low power-consumption modes.
4.2 Resets
The microcontroller unit (MCU) can be reset in any of these four ways:
1. An active-low input to the RESET pin
2. A power-on reset (POR) function
3. A clock monitor failure
4. A computer operating properly (COP) watchdog timer timeout
The RESET input consists mainly of a Schmitt trigger that senses the RESET line logic level.
4.2.1 RESET Pin
To request an external reset, the RESET pin must be held low for at least eight E-clock cycles, or for one
E-clock cycle if no distinction is needed between internal and external resets.
4.2.2 Power-On Reset (POR)
Power-on reset occurs when a positive transition is detected on VDD. This reset is used strictly for power
turn on conditions and should not be used to detect any drop in the power supply voltage. If the external
RESET pin is low at the end of the power-on delay time, the processor remains in the reset condition until
RESET goes high.
4.2.3 Computer Operating Properly (COP) Reset
The MCU contains a watchdog timer that automatically times out unless it is serviced within a specific
time by a program reset sequence. If the COP watchdog timer is allowed to timeout, a reset is generated,
which drives the RESET pin low to reset the MCU and the external system.
In the MC68HC711D3, the COP reset function is enabled out of reset in normal modes. If the user does
not want the COP enabled, he must write a 1 to the NOCOP bit of the configuration control register
(CONFIG) after reset. This bit is writable only once after reset in normal modes (see 2.3.3 Configuration
Control Register for more information). Protected control bits (CR1 and CR0) in the configuration options
register (OPTION) allow the user to select one of the four COP timeout rates. Table 4-1 shows the
relationship between CR1 and CR0 and the COP timeout period for various system clock frequencies.
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
47
Resets, Interrupts, and Low-Power Modes
The sequence for resetting the watchdog timer is:
1. Write $55 to the COP reset register (COPRST) to arm the COP timer clearing mechanism.
2. Write $AA to the COPRST register to clear the COP timer
Both writes must occur in this sequence prior to the timeout, but any number of instructions can be
executed between the two writes.
Table 4-1. COP Time Out Periods
E ÷ 215
CR0 CR1 Divided
By
XTAL = 223
Time Out
–0/+15.6 ms
XTAL =
8.0 MHz
Time Out
–0/+16.4 ms
XTAL =
4.9152 MHz
Time Out
–0/+26.7 ms
XTAL =
4.0 MHz
Time Out
–0/+32.8 ms
XTAL =
3.6864 MHz
Time Out
–0/+35.6 ms
0
0
1
15.625 ms
16.384 ms
26.667 ms
32.768 ms
35.556 ms
0
1
4
62.5 ms
65.536 ms
106.67 ms
131.07 ms
142.22 ms
1
0
16
250 ms
262.14 ms
426.67 ms
524.29 ms
568.89 ms
1
1
64
1 sec
1.049 sec
1.707 sec
2.1 sec
2.276 ms
E=
2.1 MHz
2.0 MHz
1.2288 MHz
1.0 MHz
921.6 kHz
Address:
Read:
Write:
Reset:
$003A
Bit 7
6
5
4
3
2
1
Bit 0
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0
0
0
0
0
0
0
0
Figure 4-1. Arm/Reset COP Timer Circuitry Register (COPRST)
4.2.4 Clock Monitor Reset
The MCU contains a clock monitor circuit that measures the E-clock frequency. If the E-clock input rate
is above approximately 200 kHz, then the clock monitor does not generate an MCU reset. If the E-clock
signal is lost or its frequency falls below 10 kHz, then an MCU reset can be generated, and the RESET
pin is driven low to reset the external system.
4.2.5 System Configuration Options Register
The system configuration options register (OPTION) is a special-purpose register with several
time-protected bits. OPTION is used during initialization to configure internal system options.
Bits 5, 4, 2, 1, and 0 can be written only once during the first 64 E-clock cycles after reset in normal modes
(where the HPRIO register bit (SMOD) is cleared). In special modes (where SMOD = 1), the bits can be
written at any time. Bit 3 can be written at anytime.
MC68HC711D3 Data Sheet, Rev. 2.1
48
Freescale Semiconductor
Interrupts
Address:
Read:
Write:
Reset:
$0039
Bit 7
6
5
4
3
2
1
Bit 0
0
0
IRQE
DLY
CME
0
CR1
CR0
0
0
0
1
0
0
0
0
Figure 4-2. System Configuration Options Register (OPTION)
Bits 7, 6, and 2 — Not implemented
Always read 0.
IRQE — IRQ Edge/Level Sensitivity Select
This bit can be written only once during the first 64 E-clock cycles after reset in normal modes.
1 = IRQ is configured to respond only to falling edges.
0 = IRQ is configured for low-level wired-OR operation.
DLY — Stop Mode Exit Turnon Delay
This bit is set during reset and can be written only once during the first 64 E-clock cycles after reset in
normal modes. If an external clock source rather than a crystal is used, the stabilization delay can be
inhibited because the clock source is assumed to be stable.
1 = A stabilization delay of 4064 E-clock cycles is imposed before processing resumes after a stop
mode wakeup.
0 = No stabilization delay is imposed after story recovery.
CME — Clock Monitor Enable
1 = Clock monitor circuit is enabled.
0 = Clock monitor circuit is disabled.
CR1 and CR0 — COP Timer Rate Selects
The COP system is driven by a constant frequency of E ÷ 215. These two bits specify an additional
divide-by value to arrive at the COP timeout rate. These bits are cleared during reset and can be written
only once during the first 64 E-clock cycles after reset in normal modes. The value of these bits is:
CR1
CR0
E ÷ 215
Divided By
0
0
1
0
1
4
1
0
16
1
1
64
4.3 Interrupts
Excluding reset-type interrupts, there are 17 hardware interrupts and one software interrupt that can be
generated from all the possible sources. These interrupts can be divided into two categories: maskable
and non-maskable. Fifteen of the interrupts can be masked using the I bit of the condition code register
(CCR). All the on-chip (hardware) interrupts are individually maskable by local control bits. The software
interrupt is non-maskable. The external input to the XIRQ pin is considered a non-maskable interrupt
because it cannot be masked by software once it is enabled. However, it is masked during reset and upon
receipt of an interrupt at the XIRQ pin. Illegal opcode is also a non-maskable interrupt.
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
49
Resets, Interrupts, and Low-Power Modes
Table 4-2 provides a list of the interrupts with a vector location in memory for each, as well as the actual
condition code and control bits that mask each interrupt. Figure 4-3 shows the interrupt stacking order.
Table 4-2. Interrupt and Reset Vector Assignments
Vector
Address
Interrupt Source
CCR
Mask
Local
Mask
—
—
$FFC0, $FFC1
↓
$FFD4, $FFD5
Reserved
$FFD6, $FFD7
SCI serial system:
• SCI transmit complete
• SCI transmit data register empty
• SCI idle line detect
• SCI receiver overrun
• SCI receive data register full
I bit
$FFD8, $FFD9
SPI serial transfer complete
I bit
SPIE
$FFDA, $FFDB
Pulse accumulator input edge
I bit
PAII
$FFDC, $FFDD
Pulse accumulator overflow
I bit
PAOVI
$FFDE, $FFDF
Timer overflow
I bit
TOI
$FFE0, $FFE1
Timer input capture 4/output compare 5
I bit
I4/O5I
$FFE2, $FFE3
Timer output compare 4
I bit
OC4I
$FFE4, $FFE5
Timer output compare 3
I bit
OC3I
$FFE6, $FFE7
Timer output compare 2
I bit
OC2I
$FFE8, $FFE9
Timer output compare 1
I bit
OC1I
$FFEA, $FFEB
Timer input capture 3
I bit
IC3I
$FFEC, $FFED
Timer input capture 2
I bit
IC2I
$FFEE, $FFEF
Timer input capture 1
I bit
IC1I
$FFF0, $FFF1
Real time interrupt
I bit
RTII
$FFF2, $FFF3
IRQ (external pin)
I bit
None
$FFF4, $FFF5
XIRQ pin (pseudo non-maskable)
X bit
None
$FFF6, $FFF7
Software interrupt
None
None
$FFF8, $FFF9
Illegal opcode trap
None
None
$FFFA, $FFFB
COP failure (reset)
None
NOCOP
$FFFC, $FFFD
Clock monitor fail (reset)
None
CME
$FFFE, $FFFF
RESET
None
None
TCIE
TIE
ILIE
RIE
RIE
MC68HC711D3 Data Sheet, Rev. 2.1
50
Freescale Semiconductor
Interrupts
STACK
SP
PCL
SP – 1
PCH
SP – 2
IYL
SP – 3
IYH
SP – 4
IXL
SP – 5
IXH
SP – 6
ACCA
SP – 7
ACCB
SP – 8
CCR
SP – 9
— SP BEFORE INTERRUPT
— SP AFTER INTERRUPT
Figure 4-3. Interrupt Stacking Order
4.3.1 Software Interrupt (SWI)
The SWI is executed the same as any other instruction and takes precedence over interrupts only if the
other interrupts are masked (with I and X bits in the CCR set). SWI execution is similar to that of the
maskable interrupts in that it sets the I bit, stacks the central processor unit (CPU) registers, etc.
NOTE
The SWI instruction cannot be executed as long as another interrupt is
pending. However, once the SWI instruction has begun, no other interrupt
can be honored until the first instruction in the SWI service routine is
completed.
4.3.2 Illegal Opcode Trap
Since not all possible opcodes or opcode sequences are defined, an illegal opcode detection circuit has
been included in the MCU. When an illegal opcode is detected, an interrupt is required to the illegal
opcode vector. The illegal opcode vector should never be left uninitialized.
4.3.3 Real-Time Interrupt (RTI)
The real-time interrupt (RTI) provides a programmable periodic interrupt. This interrupt is maskable by
either the I bit in the CCR or the RTI enable (RTII) bit of the timer interrupt mask register 2 (TMSK2). The
rate is based on the MCU E clock and is software selectable to the E ÷ 213, E ÷ 214, E ÷ 215, or E ÷ 216.
See PACTL, TMSK2, and TFLG2 register descriptions in Chapter 8 Programmable Timer for control and
status bit information.
4.3.4 Interrupt Mask Bits in the CCR
Upon reset, both the X bit and I bit of the CCR are set to inhibit all maskable interrupts and XIRQ. After
minimum system initialization, software may clear the X bit by a TAP instruction, thus enabling XIRQ
interrupts. Thereafter software cannot set the X bit. So, an XIRQ interrupt is effectively a non-maskable
interrupt. Since the operation of the I bit related interrupt structure has no effect on the X bit, the internal
XIRQ pin remains effectively non-masked. In the interrupt priority logic, the XIRQ interrupt is a higher
priority than any source that is maskable by the I bit. All I bit related interrupts operate normally with their
own priority relationship.
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
51
Resets, Interrupts, and Low-Power Modes
When an I bit related interrupt occurs, the I bit is automatically set by hardware after stacking the CCR
byte. The X bit is not affected. When an X bit related interrupt occurs, both the X and the I bit are
automatically set by hardware after stacking the CCR. A return-from-interrupt (RTI) instruction restores
the X and I bits to their preinterrupt request state.
4.3.5 Priority Structure
Interrupts obey a fixed hardware priority circuit to resolve simultaneous requests. However one I bit
related interrupt source may be elevated to the highest I bit priority in the resolution circuit.
Six interrupt sources are not masked by the I bit in the CCR and have these fixed priority relationships:
1. Reset
2. Clock monitor failure
3. COP failure
4. Illegal opcode
5. SWI
6. XIRQ
SWI is actually an instruction and has highest priority, other than resets, in that once the SWI opcode is
fetched, no other interrupt can be honored until the SWI vector has been fetched.
Each of the previous sources is an input to the priority resolution circuit. The highest I bit masked priority
input to the resolution circuit is assigned to be connected to any one of the remaining I bit related interrupt
sources. This assignment is made under the software control of the HPRIO register. To avoid timing
races, the HPRIO register can be written only while the I bit related interrupts are inhibited (I bit of CCR
is logic 1). An interrupt that is assigned to this higher priority position is still subject to masking by any
associated control bits or by the I bit in the CCR. The interrupt vector address is not affected by assigning
a source to the higher priority position.
Figure 4-4, Figure 4-5, and Figure 4-6 illustrate the interrupt process as it relates to normal processing.
Figure 4-4 shows how the CPU begins from a reset, and how interrupt detection relates to normal opcode
fetches. Figure 4-5 is an expansion of a block in Figure 4-4 and shows how interrupt priority is resolved.
Figure 4-6 is an expansion of the SCI interrupt block of Figure 4-4 and shows the resolution of interrupt
sources within the SCI subsystem.
MC68HC711D3 Data Sheet, Rev. 2.1
52
Freescale Semiconductor
Interrupts
HIGHEST
PRIORITY
POWER-ON RESET
(POR)
DELAY 4064 E CYCLES
EXTERNAL RESET
CLOCK MONITOR FAIL
(WITH CME = 1)
LOWEST
PRIORITY
COP WATCHDOG
TIMEOUT
(WITH NOCOP = 0)
LOAD PROGRAM COUNTER
WITH CONTENTS OF
$FFFE, $FFFF
(VECTOR FETCH)
LOAD PROGRAM COUNTER
WITH CONTENTS OF
$FFFC, $FFFD
(VECTOR FETCH)
LOAD PROGRAM COUNTER
WITH CONTENTS OF
$FFFA, $FFFB
(VECTOR FETCH)
SET BITS S, I, AND X
RESET MCU
HARDWARE
1A
BEGIN INSTRUCTION
SEQUENCE
Y
BIT X IN
CCR = 1?
N
XIRQ
PIN LOW?
Y
N
2A
STACK CPU
REGISTERS
SET BITS I AND X
FETCH VECTOR
$FFF4, $FFF5
Figure 4-4. Processing Flow Out of Reset (Sheet 1 of 2)
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
53
Resets, Interrupts, and Low-Power Modes
2A
Y
I BIT IN
CCR SET?
N
ANY I-BIT
INTERRUPT
PENDING?
Y
STACK CPU
REGISTERS
N
FETCH OPCODE
N
STACK CPU
REGISTERS
ILLEGAL
OPCODE?
Y
SET I BIT
WAI
Y
INSTRUCTION?
FETCH VECTOR
$FFF8, $FFF9
STACK CPU
REGISTERS
N
Y
STACK CPU
REGISTERS
SWI
INSTRUCTION?
N
Y
RTI
INSTRUCTION?
N
RESTORE CPU
REGISTERS
FROM STACK
EXECUTE THIS
INSTRUCTION
1A
INTERRUPT
YET?
Y
SET I BIT
FETCH VECTOR
$FFF6, $FFF7
N
SET I BIT
RESOLVE INTERRUPT
PRIORITY AND FETCH
VECTOR FOR HIGHEST
PENDING SOURCE
SEE Figure 4-5
START NEXT
INSTRUCTION
SEQUENCE
Figure 4-4. Processing Flow Out of Reset (Sheet 2 of 2)
MC68HC711D3 Data Sheet, Rev. 2.1
54
Freescale Semiconductor
Interrupts
BEGIN
X BIT
IN CCR
SET ?
Y
N
XIRQ PIN
LOW ?
Y
FETCH VECTOR
$FFF4, $FFF5
N
HIGHEST
PRIORITY
INTERRUPT
?
N
IRQ ?
SET X BIT
Y
FETCH VECTOR
Y
FETCH VECTOR
$FFF2, $FFF3
N
RTII = 1 ?
Y
N
REAL-TIME
INTERRUPT
?
Y
FETCH VECTOR
$FFF0, $FFF1
Y
FETCH VECTOR
$FFEE, $FFEF
Y
FETCH VECTOR
$FFEC, $FFED
Y
FETCH VECTOR
$FFEA, $FFEB
Y
FETCH VECTOR
$FFE8, $FFE9
N
Y
IC1I = 1 ?
N
TIMER
IC1F ?
N
Y
IC2I = 1 ?
N
TIMER
IC2F ?
N
Y
IC3I = 1 ?
N
TIMER
IC3F ?
N
Y
OC1I = 1 ?
N
TIMER
OC1F ?
N
2A
2B
Figure 4-5. Interrupt Priority Resolution (Sheet 1 of 2)
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
55
Resets, Interrupts, and Low-Power Modes
2A
2B
Y
OC2I = 1?
Y
FETCH VECTOR
$FFE6, $FFE7
Y
FETCH VECTOR
$FFE4, $FFE5
Y
FETCH VECTOR
$FFE2, $FFE3
Y
FETCH VECTOR
$FFE0, $FFE1
Y
FETCH VECTOR
$FFDE, $FFDF
Y
FETCH VECTOR
$FFDC, $FFDD
Y
FETCH VECTOR
$FFDA, $FFDB
Y
FETCH VECTOR
$FFD8, $FFD9
N
N
OC3I = 1?
Y
FLAG
OC3F = 1
N
N
OC4I = 1?
Y
FLAG
OC4F = 1?
N
N
OC5I = 1?
Y
FLAG
OC5F = 1?
N
N
Y
TOI = 1?
FLAG
TOF = 1?
N
N
PAOVI = 1?
Y
FLAG
PAOVF = 1
N
N
PAII = 1?
Y
FLAG
PAIF = 1?
N
N
SPIE = 1?
Y
FLAGS
SPIF = 1? OR
MODF = 1?
N
N
SCI
INTERRUPT?
SEE Figure 4-6
N
FLAG
OC2F = 1?
Y
FETCH VECTOR
$FFD6, $FFD7
FETCH VECTOR
$FFF2, $FFF3
END
Figure 4-5. Interrupt Priority Resolution (Sheet 2 of 2)
MC68HC711D3 Data Sheet, Rev. 2.1
56
Freescale Semiconductor
Interrupts
BEGIN
FLAG
RDRF = 1?
Y
N
OR = 1?
Y
Y
RE = 1?
TIE = 1?
Y
TE = 1?
Y
N
Y
TCIE = 1?
Y
N
N
IDLE = 1?
Y
N
N
N
TC = 1?
Y
N
N
TDRE = 1?
RIE = 1?
Y
Y
ILIE = 1?
RE = 1?
N
N
NO
VALID SCI REQUEST
Y
N
YES
VALID SCI REQUEST
Figure 4-6. Interrupt Source Resolution within SCI
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
57
Resets, Interrupts, and Low-Power Modes
4.3.6 Highest Priority I Interrupt and Miscellaneous Register (HPRIO)
Four bits of this register (PSEL3–PSEL0) are used to select one of the I bit related interrupt sources and
to elevate it to the highest I bit masked position of the priority resolution circuit. In addition, four
miscellaneous system control bits are included in this register.
Address:
$003C
Bit 7
Read:
Write:
RBOOT
6
SMOD
Reset:
5
4
3
2
1
Bit 0
MDA
IRVNE
PSEL3
PSEL2
PSEL1
PSEL0
0
1
0
1
Note 1
1. The values of the RBOOT, SMOD, IRVNE, and MDA bits at reset depend on the
mode during initialization. Refer to Table 4-3.
Figure 4-7. Highest Priority I-Bit Interrupt
and Miscellaneous Register (HPRIO)
RBOOT — Read Bootstrap ROM
This bit can be read at any time. It can be written only in special modes (SMOD = 1). In special
bootstrap mode, it is set during reset. Reset clears it in all other modes.
1 = Bootloader ROM is enabled in the memory map at $BF00–$BFFF.
0 = Bootloader ROM is disabled and is not in the memory map.
SMOD and MDA — Special Mode Select and Mode Select A
These two bits can be read at any time.These bits reflect the status of the MODA and MODB input pins
at the rising edge of reset. SMOD may be written only in special modes. It cannot be written to a 1 after
being cleared without an interim reset. MDA may be written at any time in special modes, but only once
in normal modes. An interpretation of the values of these two bits is shown in Table 4-3.
Table 4-3. Hardware Mode Select Summary
Inputs
Latched at Reset
Mode
MODB
MODA
SMOD
MDA
1
0
Single chip
0
0
1
1
Expanded multiplexed
0
1
0
0
Special bootstrap
1
0
0
1
Special test
1
1
IRVNE — Internal Read Visibility/Not E
This bit may be read at any time. It may be written once in any mode. IRVNE is set during reset in
special test mode only, and cleared by reset in the other modes.
1 = Data from internal reads is driven out on the external data bus in expanded modes.
0 = Data from internal reads is not visible on the external data bus.
As shown in the table, in single-chip and bootstrap modes IRVNE determines whether the E clock is
driven out or forced low.
1 = E pin driven low
0 = E clock driven out of the chip
MC68HC711D3 Data Sheet, Rev. 2.1
58
Freescale Semiconductor
Interrupts
IRVNE
E Clock
IRV
IRVNE
IRVNE
Out
Out
Out
Affects
May
of Reset of Reset of Reset
Only
be Written
Mode
Single chip
0
On
Off
E
Once
Expanded multiplexed
0
On
Off
IRV
Once
Bootstrap
0
On
Off
E
Once
Special test
1
On
On
IRV
Once
NOTE
To prevent bus conflicts, when using internal read visibility, the user must
disable all external devices from driving the data bus during any internal
access.
PSEL3–PSEL0 — Priority Selects
These four bits are used to specify one I bit related interrupt source, which then becomes the highest
priority I bit related interrupt source. These bits may be written only while the I bit in the CCR is set,
inhibiting I bit related interrupts. An interpretation of the value of these bits is shown in Table 4-4.
During reset, PSEL3–PSEL0 are initialized to 0101, which corresponds to reserved (default to IRQ).
IRQ becomes the highest priority I bit related interrupt source.
Table 4-4. Highest Priority Interrupt Selection
PSEL3–PSEL0
Interrupt Source Promoted
0000
Timer overflow
0001
Pulse accumulator overflow
0010
Pulse accumulator input edge
0011
SPI serial transfer complete
0100
SCI serial system
0101
Reserved (default to IRQ)
0110
IRQ (external pin)
0111
Real-time interrupt
1000
Timer input capture 1
1001
Timer input capture 2
1010
Timer input capture 3
1011
Timer output compare 1
1100
Timer output compare 2
1101
Timer output compare 3
1110
Timer output compare 4
1111
Timer input capture 4/output compare 5
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
59
Resets, Interrupts, and Low-Power Modes
4.4 Low-Power Operation
The M68HC11 Family of microcontroller units (MCU) has two programmable low power-consumption
modes: stop and wait. In the wait mode, the on-chip oscillator remains active. In the stop mode, the
oscillator is stopped. This subsection describes these two low power-consumption modes.
4.4.1 Stop Mode
The STOP instruction places the MCU in its lowest power-consumption mode, provided the S bit in the
CCR is cleared. In this mode, all clocks are stopped, thereby halting all internal processing.
To exit the stop mode, a low level must be applied to either the IRQ, XIRQ, or RESET pin. An external
interrupt used at IRQ is only effective if the I bit in the CCR is cleared. An external interrupt applied at the
XIRQ input is effective, regardless of the setting of the X bit of the CCR. However, the actual recovery
sequence differs, depending on the X bit setting. If the X bit is cleared, the MCU starts with the stacking
sequence leading to the normal service of the XIRQ request. If the X bit is set, the processing always
continues with the instruction immediately following the STOP instruction. A low input to the RESET pin
always results in an exit from the stop mode, and the start of MCU operations is determined by the reset
vector.
The CPU will not exit stop mode correctly when interrupted by IRQ or XIRQ if the instruction preceding
STOP is a column 4 or 5 accumulator inherent (opcodes $4X and $5X) instruction, such as NEGA, NEGB,
COMA, COMB, etc. These single-byte, two-cycle instructions must be followed by an NOP, then the
STOP command. If reset is used to exit stop mode, the CPU will respond properly.
A restart delay is required if the internal oscillator is being used. The delay allows the oscillator to stabilize
when exiting the stop mode. If a stable external oscillator is being used, the delay (DLY) bit in the OPTION
register can be cleared to bypass the delay. If the DLY bit is clear, the RESET pin would not normally be
used to exit the stop mode. The reset sequence sets the DLY bit, and the restart delay would be
reimposed.
4.4.2 Wait Mode
The wait (WAI) instruction places the MCU in a low power-consumption mode. The wait mode consumes
more power than the stop mode since the oscillator is kept running. Upon execution of the WAI instruction,
the machine state is stacked and program execution stops.
The wait state can be exited only by an unmasked interrupt or RESET. If the I bit of the CCR is set and
the COP is disabled, the timer system is turned off by WAI to further reduce power consumption. The
amount of power savings is application dependent. It also depends upon the circuitry connected to the
MCU pins, and upon subsystems such as the timer, serial peripheral interface (SPI), or serial
communications interface (SCI) that were or were not active when the wait mode was entered.
MC68HC711D3 Data Sheet, Rev. 2.1
60
Freescale Semiconductor
Chapter 5
Input/Output (I/O) Ports
5.1 Introduction
The MC68HC711D3 has four 8-bit input/output (I/O) ports; A, B, C, and D. In the 40-pin version, port A
bits 4 and 6 are not bonded. Port functions are controlled by the particular mode of operation selected, as
shown in Table 1-1. Port Signal Functions.
In the single-chip and bootstrap modes, all the ports are configured as parallel input/output (I/O) data
ports. In expanded multiplexed and test modes, ports B, C, and lines D6 (AS) and D7 (R/W) are
configured as a memory expansion bus, with:
• Port B as the high-order address bus
• Port C as the multiplexed address and data bus
• AS as the demultiplexing signal
• R/W as data bus direction control
The remaining ports are unaffected by mode changes.
• Ports A and D can be used as general-purpose I/O ports, though each has an alternate function.
• Port A bits handle the timer functions.
• Port D handles serial peripheral interface (SPI) and serial communications interface (SCI)
functions in addition to its bus direction control functions.
5.2 Port A
Port A shares functions with the timer system and has:
• Three input only pins
• Three output only pins
• Two bidirectional I/O pins
Pins PA6 and PA4 are not bonded in the 40-pin dual in-line package (DIP), and their OC output functions
are unavailable, but their software interrupts are available.
Address:
Read:
Write:
$0000
Bit 7
6
5
4
3
2
1
Bit 0
PA7
PA6(1)
PA5
PA4(1)
PA3
PA2
PA1
PA0
Reset:
Hi-Z
0
0
0
Hi-Z
Hi-Z
Hi-Z
Hi-Z
Alt. Func.:
And/Or:
PAI
OC1
OC2
OC1
OC3
OC1
OC4
OC1
IC4/OC5
OC1
IC1
—
IC2
—
IC3
—
1. This pin is not bonded in the 40-pin version.
Figure 5-1. Port A Data Register (PORTA)
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
61
Input/Output (I/O) Ports
PORTA can be read any time. Inputs return the pin level, whereas outputs return the pin driver input level.
If written, PORTA stores the data in an internal latch. It drives the pins only if they are configured as
outputs. Writes to PORTA do not change the pin state when the pins are configured for timer output
compares.
Out of reset, port A bits 7 and 3–0 are general high-impedance inputs, while bits 6–4 are outputs, driving
low. On bidirectional lines PA7 and PA3, the timer forces the I/O state to be an output if the associated
output compare is enabled. In this case, the data direction bits DDRA7 and DDRA3 in PACTL will not be
changed or have any effect on those bits. When the output compare functions associated with these pins
are disabled, the DDR bits in PACTL govern the I/O state.
5.3 Port B
Port B is an 8-bit, general-purpose I/O port with a data register (PORTB) and a data direction register
(DDRB).
• In the single-chip mode, port B pins are general-purpose I/O pins (PB7–PB0).
• In the expanded-multiplexed mode, all of the port B pins act as the high-order address bits
(A15–A8) of the address bus.
5.3.1 Port B Data Register
Address:
Read:
Write:
Reset:
Alt. Func.:
$0004
Bit 7
6
5
4
3
2
1
Bit 0
PB7
PB6
PB5
PB4
PB3
PB2
PB1
PB0
0
0
0
0
0
0
0
0
A15
A14
A13
A12
A11
A10
A9
A8
Figure 5-2. Port B Data Register (PORTB)
PORTB can be read at any time. Inputs return the sensed levels at the pin, while outputs return the input
level of the port B pin drivers. If PORTB is written, the data is stored in an internal latch and can be driven
only if port B is configured for general-purpose outputs in single-chip or bootstrap mode.
Port B pins are general--purpose inputs out of reset in single-chip and bootstrap modes. These pins are
outputs (the high-order address bits) out of reset in expanded multiplexed and test modes.
5.3.2 Port B Data Direction Register
Address:
Read:
Write:
Reset:
$0006
Bit 7
6
5
4
3
2
1
Bit 0
DDB7
DDB6
DDB5
DDB4
DDB3
DDB2
DDB1
DDB0
0
0
0
0
0
0
0
0
Figure 5-3. Data Direction Register for Port B (DDRB)
DDB7–DDB0 — Data Direction Bits for Port B
1 = Corresponding port B pin configured as output
0 = Corresponding port B pin configured for input only
MC68HC711D3 Data Sheet, Rev. 2.1
62
Freescale Semiconductor
Port C
5.4 Port C
Port C is an 8-bit, general-purpose I/O port with a data register (PORTC) and a data direction register
(DDRC). In the single-chip mode, port C pins are general-purpose I/O pins (PC7–PC0). In the
expanded-multiplexed mode, port C pins are configured as multiplexed address/data pins. During the
address cycle, bits 7–0 of the address are output on PC7–PC0. During the data cycle, bits 7–0
(PC7–PC0) are bidirectional data pins controlled by the R/W signal.
5.4.1 Port C Control Register
Address:
Read:
Write:
Reset:
$0002
Bit 7
6
5
4
3
2
1
Bit 0
0
0
CWOM
0
0
0
0
0
0
0
0
0
0
0
0
0
Figure 5-4. Port C Control Register (PIOC)
CWOM — Port C Wire-OR Mode Bit
1 = Port C outputs are open drain (to facilitate testing)
0 = Port C operates normally
5.4.2 Port C Data Register
Address:
Read:
Write:
Reset:
$0003
Bit 7
6
5
4
3
2
1
Bit 0
PC7
PC6
PC5
PC4
PC3
PC2
PC1
PC0
0
0
0
0
0
0
0
0
Figure 5-5. Port C Data Register (PORTC)
PORTC can be read at any time. Inputs return the sensed levels at the pin, while outputs return the input
level of the port C pin drivers. If PORTC is written, the data is stored in an internal latch and can be driven
only if port C is configured for general-purpose outputs in single-chip or bootstrap mode.
Port C pins are general-purpose inputs out of reset in single-chip and bootstrap modes. These pins are
multiplexed low-order address and data bus lines out of reset in expanded-multiplexed and test modes.
5.4.3 Port C Data Direction Register
Address:
Read:
Write:
Reset:
$0007
Bit 7
6
5
4
3
2
1
Bit 0
DDC7
DDC6
DDC5
DDC4
DDC3
DDC2
DDC1
DDC0
0
0
0
0
0
0
0
0
Figure 5-6. Data Direction Register for Port C (DDRC)
DDC7–DDC0 — Data Direction Bits for Port C
1 = Corresponding port C pin is configured as output
0 = Corresponding port C pin is configured for input only
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
63
Input/Output (I/O) Ports
5.5 Port D
Port D is an 8-bit, general-purpose I/O port with a data register (PORTD) and a data direction register
(DDRD). The eight port D bits (D7–D0) can be used for general-purpose I/O, for the serial
communications interface (SCI) and serial peripheral interface (SPI) subsystems, or for bus data direction
control
5.5.1 Port D Data Register
Address:
Read:
Write:
Reset:
$0008
Bit 7
6
5
4
3
2
1
Bit 0
PD7
PD6
PD5
PD4
PD3
PD2
PD1
PD0
0
0
0
0
0
0
0
0
Figure 5-7. Port D Data Register (PORTD)
PORTD can be read at any time and inputs return the sensed levels at the pin; whereas, outputs return
the input level of the port D pin drivers. If PORTD is written, the data is stored in an internal latch, and can
be driven only if port D is configured as general-purpose output. This port shares functions with the
on-chip SCI and SPI subsystems, while bits 6 and 7 control the direction of data flow on the bus in
expanded and special test modes.
5.5.2 Port D Data Direction Register
Address:
Read:
Write:
Reset:
$0009
Bit 7
6
5
4
3
2
1
Bit 0
DDD7
DDD6
DDD5
DDD4
DDD3
DDD2
DDD1
DDD0
0
0
0
0
0
0
0
0
Figure 5-8. Data Direction Register for Port D (DDRD)
DDD7–DDD0 — Data Direction for Port D
When port D is a general-purpose I/O port, the DDRD register controls the direction of the I/O pins as
follows:
0 = Configures the corresponding port D pin for input only
1 = Configures the corresponding port D pin for output
In expanded and test modes, bits 6 and 7 are dedicated AS and R/W.
When port D is functioning with the SPI system enabled, bit 5 is dedicated as the slave select (SS)
input. In SPI slave mode, DDD5 has no meaning or effect. In SPI master mode, DDD5 affects port D
bit 5 as follows:
0 = Port D bit 5 is an error-detect input to the SPI.
1 = Port D bit 5 is configured as a general-purpose output line.
If the SPI is enabled and expects port D bits 2, 3, and 4 (MISO, MOSI, and SCK) to be inputs, then
they are inputs, regardless of the state of DDRD bits 2, 3, and 4. If the SPI expects port D bits 2, 3,
and 4 to be outputs, they are outputs only if DDRD bits 2, 3, and 4 are set.
MC68HC711D3 Data Sheet, Rev. 2.1
64
Freescale Semiconductor
Chapter 6
Serial Communications Interface (SCI)
6.1 Introduction
The serial communications interface (SCI) is a universal asynchronous receiver transmitter (UART), one
of two independent serial input/output (I/O) subsystems in the MC68HC711D3. It has a standard
non-return to zero (NRZ) format (one start, eight or nine data, and one stop bit). Several baud rates are
available. The SCI transmitter and receiver are independent, but use the same data format and bit rate.
6.2 Data Format
The serial data format requires these conditions:
• An idle line in the high state before transmission or reception of a message
• A start bit, logic 0, transmitted or received, that indicates the start of each character
• Data that is transmitted and received least significant bit (LSB) first
• A stop bit, logic 1, used to indicate the end of a frame. A frame consists of a start bit, a character
of eight or nine data bits, and a stop bit.
• A break, defined as the transmission or reception of a logic 0 for some multiple number of frames
Selection of the word length is controlled by the M bit in the SCI control register 1 (SCCR1).
6.3 Transmit Operation
The SCI transmitter includes a parallel transmit data register (SCDR) and a serial shift register that puts
data from the SCDR into serial form. The contents of the serial shift register can only be written through
the SCDR. This double-buffered operation allows a character to be shifted out serially while another
character is waiting in the SCDR to be transferred into the serial shift register. The output of the serial shift
register is applied to PD1 as long as transmission is in progress or the transmit enable (TE) bit of serial
communication control register 2 (SCCR2) is set. The block diagram, Figure 6-1, shows the transmit serial
shift register and the buffer logic at the top of the figure.
6.4 Receive Operation
During receive operations, the transmit sequence is reversed. The serial shift register receives data and
transfers it to a parallel receive data register (SCDR) as a complete word. Refer to Figure 6-2. This
double-buffered operation allows a character to be shifted in serially while another character is already in
the SCDR. An advanced data recovery scheme distinguishes valid data from noise in the serial data
stream. The data input is selectively sampled to detect receive data, and a majority voting circuit
determines the value and integrity of each bit.
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
65
Serial Communications Interface (SCI)
TRANSMITTER
BAUD RATE
CLOCK
(WRITE ONLY)
SCDR Tx BUFFER
DDD1
10 (11) - BIT Tx SHIFT REGISTER
2
1
0
PIN BUFFER
AND CONTROL
L
PD1
TxD
BREAK—JAM 0s
3
JAM ENABLE
4
PREAMBLE—JAM 1s
5
SHIFT ENABLE
6
TRANSFER Tx BUFFER
SIZE 8/9
H (8) 7
FORCE PIN
DIRECTION (OUT)
SCCR1 SCI CONTROL 1
FE
NF
OR
IDLE
TC
RDRF
TDRE
WAKE
M
T8
R8
TRANSMITTER
CONTROL LOGIC
SCSR INTERRUPT STATUS
TDRE
TIE
TC
SBK
RWU
RE
TE
ILIE
RIE
TCIE
TIE
TCIE
SCCR2 SCI CONTROL 2
SCI Rx
REQUESTS
SCI INTERRUPT
REQUEST
INTERNAL
DATA BUS
Figure 6-1. SCI Transmitter Block Diagram
MC68HC711D3 Data Sheet, Rev. 2.1
66
Freescale Semiconductor
Receive Operation
16X
BAUD RATE
CLOCK
PIN BUFFER
AND CONTROL
PD0
RxD
10 (11) - BIT
Rx SHIFT REGISTER
STOP
÷16
DATA
RECOVERY
START
DDD0
(8) 7
6
5
4
3
MSB
DISABLE
DRIVER
2
1
0
ALL 1s
RE
M
FE
NF
OR
IDLE
RDRF
TDRE
TC
RWU
WAKE
M
T8
R8
WAKEUP
LOGIC
SCDR Rx BUFFER
SCSR SCI STATUS 1
SCCR1 SCI CONTROL 1
(READ ONLY)
RDRF
RIE
IDLE
ILIE
OR
SBK
RWU
RE
TE
ILIE
RIE
TCIE
TIE
RIE
SCCR2 SCI CONTROL 2
SCI Tx
REQUESTS
SCI INTERRUPT
REQUEST
INTERNAL
DATA BUS
Figure 6-2. SCI Receiver Block Diagram
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
67
Serial Communications Interface (SCI)
6.5 Wakeup Feature
The wakeup feature reduces SCI service overhead in multiple receiver systems. Software for each
receiver evaluates the first character of each message. The receiver is placed in wakeup mode by writing
a 1 to the RWU bit in the SCCR2 register. While RWU is 1, all of the receiver-related status flags (RDRF,
IDLE, OR, NF, and FE) are inhibited (cannot become set). Although RWU can be cleared by a software
write to SCCR2, to do so would be unusual. Normally, RWU is set by software and is cleared
automatically with hardware. Whenever a new message begins, logic alerts the sleeping receivers to
wake up and evaluate the initial character of the new message.
Two methods of wakeup are available:
• Idle line wakeup
• Address mark wakeup
During idle line wakeup, a sleeping receiver awakens as soon as the RxD line becomes idle. In the
address mark wakeup, logic 1 in the most significant bit (MSB) of a character wakes up all sleeping
receivers.
6.5.1 Idle-Line Wakeup
To use the receiver wakeup method, establish a software addressing scheme to allow the transmitting
devices to direct a message to individual receivers or to groups of receivers. This addressing scheme can
take any form as long as all transmitting and receiving devices are programmed to understand the same
scheme. Because the addressing information is usually the first frame(s) in a message, receivers that are
not part of the current task do not become burdened with the entire set of addressing frames. All receivers
are awake (RWU = 0) when each message begins. As soon as a receiver determines that the message
is not intended for it, software sets the RWU bit (RWU = 1), which inhibits further flag setting until the RxD
line goes idle at the end of the message. As soon as an idle line is detected by receiver logic, hardware
automatically clears the RWU bit so that the first frame of the next message can be received. This type
of receiver wakeup requires a minimum of one idle-line frame time between messages and no idle time
between frames in a message.
6.5.2 Address-Mark Wakeup
The serial characters in this type of wakeup consist of seven (eight if M = 1) information bits and an MSB,
which indicates an address character (when set to 1 — mark). The first character of each message is an
addressing character (MSB = 1). All receivers in the system evaluate this character to determine if the
remainder of the message is directed toward this particular receiver. As soon as a receiver determines
that a message is not intended for it, the receiver activates the RWU function by using a software write to
set the RWU bit. Because setting RWU inhibits receiver-related flags, there is no further software
overhead for the rest of this message. When the next message begins, its first character has its MSB set,
which automatically clears the RWU bit and enables normal character reception. The first character
whose MSB is set is also the first character to be received after wakeup because RWU gets cleared
before the stop bit for that frame is serially received. This type of wakeup allows messages to include gaps
of idle time, unlike the idle-line method, but there is a loss of efficiency because of the extra bit time for
each character (address bit) required for all characters.
MC68HC711D3 Data Sheet, Rev. 2.1
68
Freescale Semiconductor
SCI Error Detection
6.6 SCI Error Detection
Three error conditions can occur during generation of SCI system interrupts:
• Serial communications data register (SCDR) overrun
• Received bit noise
• Framing
Three bits (OR, NF, and FE) in the serial communications status register (SCSR) indicate if one of these
error conditions exists. The overrun error (OR) bit is set when the next byte is ready to be transferred from
the receive shift register to the SCDR and the SCDR is already full (RDRF bit is set). When an overrun
error occurs, the data that caused the overrun is lost and the data that was already in SCDR is not
disturbed. The OR is cleared when the SCSR is read (with OR set), followed by a read of the SCDR.
The noise flag (NF) bit is set if there is noise on any of the received bits, including the start and stop bits.
The NF bit is not set until the RDRF flag is set. The NF bit is cleared when the SCSR is read (with FE
equal to 1) followed by a read of the SCDR.
When no stop bit is detected in the received data character, the framing error (FE) bit is set. FE is set at
the same time as the RDRF. If the byte received causes both framing and overrun errors, the processor
only recognizes the overrun error. The framing error flag inhibits further transfer of data into the SCDR
until it is cleared. The FE bit is cleared when the SCSR is read (with FE equal to 1) followed by a read of
the SCDR.
6.7 SCI Registers
This subsection describes the five addressable registers in the SCI.
6.7.1 SCI Data Register
The SCI data register (SCDR) is a parallel register that performs two functions. It is the receive data
register when it is read, and the transmit data register when it is written. Reads access the receive data
buffer and writes access the transmit data buffer. Receive and transmit are double buffered.
Address:
Read:
Write:
Reset:
$002F
Bit 7
6
5
4
3
2
1
Bit 0
R7/T7
R6/T6
R5/T5
R4/T4
R3/T3
R2/T2
R1/T1
R0/T0
Unaffected by reset
Figure 6-3. SCI Data Register (SCDR)
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
69
Serial Communications Interface (SCI)
6.7.2 SCI Control Register 1
The SCI control register 1 (SCCR1) provides the control bits that determine word length and select the
method used for the wakeup feature.
Address:
Read:
Write:
Reset:
$002C
Bit 7
6
5
4
3
2
1
Bit 0
R8
T8
0
M
WAKE
0
0
0
U
U
0
0
0
0
0
0
U = Unaffected
Figure 6-4. SCI Control Register 1 (SCCR1)
R8 — Receive Data Bit 8
If M bit is set, R8 stores the ninth bit in the receive data character.
T8 — Transmit Data Bit 8
If M bit is set, T8 stores ninth bit in transmit data character.
M — Mode Bit
The mode bit selects character format
0 = Start bit, 8 data bits, 1 stop bit
1 = Start bit, 9 data bits, 1 stop bit
WAKE — Wakeup by Address Mark/Idle Bit
0 = Wakeup by IDLE line recognition
1 = Wakeup by address mark (most significant data bit set)
6.7.3 SCI Control Register 2
The SCI control register 2 (SCCR2) provides the control bits that enable or disable individual SCI
functions.
Address:
Read:
Write:
Reset:
$002D
Bit 7
6
5
4
3
2
1
Bit 0
TIE
TCIE
RIE
ILIE
TE
RE
RWU
SBK
0
0
0
0
0
0
0
0
Figure 6-5. SCI Control Register 2 (SCCR2)
TIE — Transmit Interrupt Enable Bit
1 = TDRE interrupts disabled
1 = SCI interrupt requested when TDRE status flag is set
TCIE — Transmit Complete Interrupt Enable Bit
0 = TC interrupts disabled
1 = SCI interrupt requested when TC status flag is set
RIE — Receiver Interrupt Enable Bit
0 = RDRF and OR interrupts disabled
1 = SCI interrupt requested when RDRF flag or the OR status flag is set
MC68HC711D3 Data Sheet, Rev. 2.1
70
Freescale Semiconductor
SCI Registers
ILIE — Idle Line Interrupt Enable Bit
1 = IDLE interrupts disabled
1 = SCI interrupt requested when IDLE status flag is set
TE — Transmitter Enable Bit
When TE goes from 0 to 1, one unit of idle character time (logic 1) is queued as a preamble.
0 = Transmitter disabled
1 = Transmitter enabled
RE — Receiver Enable Bit
0 = Receiver disabled
1 = Receiver enabled
RWU — Receiver Wakeup Control Bit
0 = Normal SCI receiver
1 = Wakeup enabled and receiver interrupts inhibited
SBK — Send Break Bit
At least one character time of break is queued and sent each time SBK is written to 1. More than one
break may be sent if the transmitter is idle at the time the SBK bit is toggled on and off, as the baud
rate clock edge could occur between writing the 1 and writing the 0 to SBK.
0 = Break generator off
1 = Break codes generated as long as SBK = 1
6.7.4 SCI Status Register
The SCI status register (SCSR) provides inputs to the interrupt logic circuits for generation of the SCI
system interrupt.
Address:
Read:
Write:
Reset:
$002E
Bit 7
6
5
4
3
2
1
Bit 0
TDRE
TC
RDRF
IDLE
OR
NF
FE
0
1
1
0
0
0
0
0
0
Figure 6-6. SCI Status Register (SCSR)
TDRE — Transmit Data Register Empty Flag
This flag is set when SCDR is empty. Clear the TDRE flag by reading SCSR with TDRE set and then
writing to SCDR.
0 = SCDR busy
1 = SCDR empty
TC — Transmit Complete Flag
This flag is set when the transmitter is idle (no data, preamble, or break transmission in progress).
Clear the TC flag by reading SCSR with TC set and then writing to SCDR.
0 = Transmitter busy
1 = Transmitter idle
RDRF — Receive Data Register Full Flag
This flag is set if a received character is ready to be read from SCDR. Clear the RDRF flag by reading
SCSR with RDRF set and then reading SCDR.
0 = SCDR empty
1 = SCDR full
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
71
Serial Communications Interface (SCI)
IDLE — Idle Line Detected Flag
This flag is set if the RxD line is idle. Once cleared, IDLE is not set again until the RxD line has been
active and becomes idle again. The IDLE flag is inhibited when RWU = 1. Clear IDLE by reading SCSR
with IDLE set and then reading SCDR.
0 = RxD line active
1 = RxD line idle
OR — Overrun Error Flag
OR is set if a new character is received before a previously received character is read from SCDR.
Clear the OR flag by reading SCSR with OR set and then reading SCDR.
0 = No overrun
1 = Overrun detected
NF — Noise Error Flag
NF is set if majority sample logic detects anything other than a unanimous decision. Clear NF by
reading SCSR with NF set and then reading SCDR.
0 = Unanimous decision
1 = Noise detected
FE — Framing Error Bit
FE is set when a 0 is detected where a stop bit was expected. Clear the FE flag by reading SCSR with
FE set and then reading SCDR.
0 = Stop bit detected
1 = Zero detected
6.7.5 Baud Rate Register
The baud rate register (BAUD) is used to select different baud rates for the SCI system. The SCP1 and
SCP0 bits function as a prescaler for the SCR2–SCR0 bits. Together, these five bits provide multiple baud
rate combinations for a given crystal frequency. Normally, this register is written once during initialization.
The prescaler is set to its fastest rate by default out of reset and can be changed at any time. Refer to
Table 6-1 and Table 6-2 for normal baud rate selections.
Address:
Read:
Write:
Reset:
$002B
Bit 7
6
5
4
3
2
1
Bit 0
TCLR
0
SCP1
SCP0
RCKB
SCR2
SCR1
SCR0
0
0
0
0
0
U
U
U
U = Unaffected
Figure 6-7. Baud Rate Register (BAUD)
TCLR — Clear Baud Rate Counters (Test)
RCKB — SCI Baud Rate Clock Check (Test)
MC68HC711D3 Data Sheet, Rev. 2.1
72
Freescale Semiconductor
SCI Registers
SCP1 and SCP0 — SCI Baud Rate Prescaler Select Bits
These two bits select a prescale factor for the SCI baud rate generator that determines the highest
possible baud rate.
Table 6-1. Baud Rate Prescale Selects
Crystal Frequency in MHz
SCP1
and SCP0
Divide
Internal Clock
By
4.0 MHz
(Baud)
8.0 MHz
(Baud)
10.0 MHz
(Baud)
12.0 MHz
(Baud)
00
1
62.50 K
125.0 K
156.25 K
187.5 K
01
3
20.83 K
41.67 K
52.08 K
62.5 K
10
4
15.625 K
31.25 K
38.4 K
46.88 K
11
13
4800
9600
12.02 K
14.42 K
SCR2–SCR0 — SCI Baud Rate Select Bits
These three bits select receiver and transmitter bit rate based on output from baud rate prescaler
stage.
Table 6-2. Baud Rate Selects
Highest Baud Rate
(Prescaler Output from Table 6-1)
Divide
Prescaler
By
4800
9600
38.4 K
000
1
4800
9600
38.4 K
001
2
2400
4800
19.2 K
010
4
1200
2400
9600
011
8
600
1200
4800
100
16
300
600
2400
101
32
150
300
1200
110
64
—
150
600
111
128
—
—
300
SCR2–SCR0
The prescale bits, SCP1 and SCP0, determine the highest baud rate and the SCR2–SCR0 bits select
an additional binary submultiple (÷1, ÷2, ÷4, through ÷128) of this highest baud rate. The result of these
two dividers in series is the 16 X receiver baud rate clock. The SCR2–SCR0 bits are not affected by
reset and can be changed at any time, although they should not be changed when any SCI transfer is
in progress.
Figure 6-8 illustrates the SCI baud rate timing chain. The prescale select bits determine the highest
baud rate. The rate select bits determine additional divide by two stages to arrive at the receiver timing
(RT) clock rate. The baud rate clock is the result of dividing the RT clock by 16.
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
73
Serial Communications Interface (SCI)
EXTAL
XTAL
INTERNAL BUS CLOCK (PH2)
OSCILLATOR
AND
CLOCK GENERATOR
÷3
(÷ 4)
÷4
÷ 13
SCP1 AND SCP0
0:0
E
0:1
1:0
1:1
AS
SCR2–SCR0
0:0:0
÷2
0:0:1
÷2
0:1:0
÷2
0:1:1
÷ 16
÷2
1:0:0
÷2
1:0:1
÷2
1:1:0
÷2
1:1:1
SCI
TRANSMIT
BAUD RATE
(1X)
SCI
RECEIVE
BAUD RATE
(16X)
Figure 6-8. SCI Baud Rate Diagram
MC68HC711D3 Data Sheet, Rev. 2.1
74
Freescale Semiconductor
Status Flags and Interrupts
6.8 Status Flags and Interrupts
The SCI transmitter has two status flags. These status flags can be read by software (polled) to tell when
the corresponding condition exists. Alternatively, a local interrupt enable bit can be set to enable each of
these status conditions to generate interrupt requests when the corresponding condition is present.
Status flags are automatically set by hardware logic conditions, but must be cleared by software, which
provides an interlock mechanism that enables logic to know when software has noticed the status
indication. The software clearing sequence for these flags is automatic — functions that are normally
performed in response to the status flags also satisfy the conditions of the clearing sequence.
TDRE and TC flags are normally set when the transmitter is first enabled (TE set to 1). The TDRE flag
indicates there is room in the transmit queue to store another data character in the TDR. The TIE bit is
the local interrupt mask for TDRE. When TIE is 0, TDRE must be polled. When TIE and TDRE are 1, an
interrupt is requested.
The TC flag indicates the transmitter has completed the queue. The TCIE bit is the local interrupt mask
for TC. When TCIE is 0, TC must be polled; when TCIE is 1 and TC is 1, an interrupt is requested.
Writing a 0 to TE requests that the transmitter stop when it can. The transmitter completes any
transmission in progress before actually shutting down. Only an MCU reset can cause the transmitter to
stop and shut down immediately. If TE is written to 0 when the transmitter is already idle, the pin reverts
to its general-purpose I/O function (synchronized to the bit-rate clock). If anything is being transmitted
when TE is written to 0, that character is completed before the pin reverts to general-purpose I/O, but any
other characters waiting in the transmit queue are lost. The TC and TDRE flags are set at the completion
of this last character, even though TE has been disabled.
The SCI receiver has five status flags, three of which can generate interrupt requests. The status flags
are set by the SCI logic in response to specific conditions in the receiver. These flags can be read (polled)
at any time by software. Refer to Figure 6-9, which shows SCI interrupt arbitration.
When an overrun takes place, the new character is lost, and the character that was in its way in the
parallel RDR is undisturbed. RDRF is set when a character has been received and transferred into the
parallel RDR. The OR flag is set instead of RDRF if overrun occurs. A new character is ready to be
transferred into RDR before a previous character is read from RDR.
The NF and FE flags provide additional information about the character in the RDR, but do not generate
interrupt requests.
The last receiver status flag and interrupt source come from the IDLE flag. The RxD line is idle if it has
constantly been at logic 1 for a full character time. The IDLE flag is set only after the RxD line has been
busy and becomes idle, which prevents repeated interrupts for the whole time RxD remains idle.
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
75
Serial Communications Interface (SCI)
BEGIN
FLAG
RDRF = 1?
Y
N
OR = 1?
Y
Y
Y
TIE = 1?
TCIE = 1?
Y
N
Y
TE = 1?
Y
N
Y
N
N
IDLE = 1?
RE = 1?
N
N
TC = 1?
Y
N
N
TDRE = 1?
RIE = 1?
Y
Y
ILIE = 1?
RE = 1?
N
N
NO
VALID SCI REQUEST
Y
N
VALID SCI REQUEST
Figure 6-9. Interrupt Source Resolution within SCI
MC68HC711D3 Data Sheet, Rev. 2.1
76
Freescale Semiconductor
Chapter 7
Serial Peripheral Interface (SPI)
7.1 Introduction
The serial peripheral interface (SPI), an independent serial communications subsystem, allows the
microcontroller unit (MCU) to communicate synchronously with peripheral devices, such as:
• Transistor-transistor logic (TTL) shift registers
• Liquid crystal diode (LCD) display drivers
• Analog-to-digital converter (ADC) subsystems
• Other microprocessors (MCUs)
The SPI is also capable of inter-processor communication in a multiple master system. The SPI system
can be configured as either a master or a slave device with data rates as high as one half of the E-clock
rate when configured as master, and as fast as the E-clock rate when configured as slave.
7.2 Functional Description
The central element in the SPI system is the block containing the shift register and the read data buffer.
The system is single buffered in the transmit direction and double buffered in the receive direction. This
means that new data for transmission cannot be written to the shifter until the previous transfer is
complete; however, received data is transferred into a parallel read data buffer so the shifter is free to
accept a second serial character. As long as the first character is read out of the read data buffer before
the next serial character is ready to be transferred, no overrun condition occurs. A single MCU register
address is used for reading data from the read data buffer, and for writing data to the shifter.
The SPI status block represents the SPI status functions (transfer complete, write collision, and mode
fault) performed by the serial peripheral status register (SPSR). The SPI control block represents those
functions that control the SPI system through the serial peripheral control register (SPCR).
Refer to Figure 7-1, which shows the SPI block diagram.
7.3 SPI Transfer Formats
During an SPI transfer, data is simultaneously transmitted and received. A serial clock line synchronizes
shifting and sampling of the information on the two serial data lines. A slave select line allows individual
selection of a slave SPI device; slave devices that are not selected do not interfere with SPI bus activities.
On a master SPI device, the select line can optionally be used to indicate a multiple master bus
contention. Refer to Figure 7-2.
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
77
Serial Peripheral Interface (SPI)
PH2
(INTERNAL)
MISO
PD2
S
M
S
M
LSB
8-BIT SHIFT REGISTER
READ DATA BUFFER
CLOCK
M
CLOCK
LOGIC
SCK
PD4
S
SPR0
DWOM
SS
PD5
MSTR
SPR1
SELECT
SPI CLOCK (MASTER)
MOSI
PD3
PIN CONTROL LOGIC
MSB
DIVIDER
÷4 ÷16 ÷32
SPE
÷2
MSTR
SPR0
SPR1
CPOL
CPHA
MSTR
DWOM
SPIE
MODF
WCOL
SPIF
SPI STATUS REGISTER
SPE
SPE
SPI CONTROL
SPI CONTROL REGISTER
8
SPI INTERRUPT
REQUEST
INTERNAL
DATA BUS
Figure 7-1. SPI Block Diagram
MC68HC711D3 Data Sheet, Rev. 2.1
78
Freescale Semiconductor
Clock Phase and Polarity Controls
SCK CYCLE #
1
2
3
4
5
6
7
8
SCK (CPOL = 0)
SCK (CPOL = 1)
SAMPLE INPUT
MSB
(CPHA = 0) DATA OUT
6
5
4
3
2
1
LSB
SAMPLE INPUT
MSB
(CPHA = 1) DATA OUT
6
5
4
3
2
1
LSB
SS (TO SLAVE)
SLAVE CPHA=1 TRANSFER IN PROGRESS
3
1. SS ASSERTED
2. MASTER WRITES TO SPDR
3. FIRST SCK EDGE
4. SPIF SET
5. SS NEGATED
MASTER TRANSFER IN PROGRESS
2
4
SLAVE CPHA=0 TRANSFER IN PROGRESS
1
5
Figure 7-2. SPI Transfer Format
7.4 Clock Phase and Polarity Controls
Software can select one of four combinations of serial clock phase and polarity using two bits in the SPI
control register (SPCR). The clock polarity is specified by the CPOL control bit, which selects an active
high or active low clock, and has no significant effect on the transfer format. The clock phase (CPHA)
control bit selects one of two different transfer formats. The clock phase and polarity should be identical
for the master SPI device and the communicating slave device. In some cases, the phase and polarity
are changed between transfers to allow a master device to communicate with peripheral slaves having
different requirements.
When CPHA equals 0, the slave select (SS) line must be negated and reasserted between each
successive serial byte. Also, if the slave writes data to the SPI data register (SPDR) while SS is active
low, a write collision error results.
When CPHA equals 1, the SS line can remain low between successive transfers.
7.5 SPI Signals
This subsection contains description of the four SPI signals:
• Master in/slave out (MISO)
• Master out/slave in (MOSI)
• Serial clock (SCK)
• Slave select (SS)
7.5.1 Master In/Slave Out (MISO)
MISO is one of two unidirectional serial data signals. It is an input to a master device and an output from
a slave device. The MISO line of a slave device is placed in the high-impedance state if the slave device
is not selected.
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
79
Serial Peripheral Interface (SPI)
7.5.2 Master Out/Slave In (MOSI)
The MOSI line is the second of the two unidirectional serial data signals. It is an output from a master
device and an input to a slave device. The master device places data on the MOSI line a half-cycle before
the clock edge that the slave device uses to latch the data.
7.5.3 Serial Clock (SCK)
SCK, an input to a slave device, is generated by the master device and synchronizes data movement in
and out of the device through the MOSI and MISO lines. Master and slave devices are capable of
exchanging a byte of information during a sequence of eight clock cycles.
Four possible timing relationships can be chosen by using control bits CPOL and CPHA in the serial
peripheral control register (SPCR). Both master and slave devices must operate with the same timing.
The SPI clock rate select bits, SPR1 and SPR0, in the SPCR of the master device, select the clock rate.
In a slave device, SPR1 and SPR0 have no effect on the operation of the SPI.
7.5.4 Slave Select (SS)
The SS input of a slave device must be externally asserted before a master device can exchange data
with the slave device. SS must be low before data transactions and must stay low for the duration of the
transaction.
The SS line of the master must be held high. If it goes low, a mode fault error flag (MODF) is set in the
serial peripheral status register (SPSR). To disable the mode fault circuit, write a 1 in bit 5 of the port D
data direction register. This sets the SS pin to act as a general-purpose output. The other three lines are
dedicated to the SPI whenever the serial peripheral interface is on.
The state of the master and slave CPHA bits affects the operation of SS. CPHA settings should be
identical for master and slave. When CPHA = 0, the shift clock is the OR of SS with SCK. In this clock
phase mode, SS must go high between successive characters in an SPI message. When CPHA = 1, SS
can be left low between successive SPI characters. In cases where there is only one SPI slave MCU, its
SS line can be tied to VSS as long as only CPHA = 1 clock mode is used.
7.6 SPI System Errors
Two system errors can be detected by the SPI system. The first type of error arises in a multiple-master
system when more than one SPI device simultaneously tries to be a master. This error is called a mode
fault. The second type of error, write collision, indicates that an attempt was made to write data to the
SPDR while a transfer was in progress.
When the SPI system is configured as a master and the SS input line goes to active low, a mode fault
error has occurred — usually because two devices have attempted to act as master at the same time. In
cases where more than one device is concurrently configured as a master, there is a chance of contention
between two pin drivers. For push-pull CMOS drivers, this contention can cause permanent damage. The
mode fault attempts to protect the device by disabling the drivers. The MSTR control bit in the SPCR and
all four DDRD control bits associated with the SPI are cleared. An interrupt is generated subject to
masking by the SPIE control bit and the I bit in the CCR.
Other precautions may need to be taken to prevent driver damage. If two devices are made masters at
the same time, mode fault does not help protect either one unless one of them selects the other as slave.
The amount of damage possible depends on the length of time both devices attempt to act as master.
MC68HC711D3 Data Sheet, Rev. 2.1
80
Freescale Semiconductor
SPI Registers
A write collision error occurs if the SPDR is written while a transfer is in progress. Because the SPDR is
not double buffered in the transmit direction, writes to SPDR cause data to be written directly into the SPI
shift register. Because this write corrupts any transfer in progress, a write collision error is generated. The
transfer continues undisturbed, and the write data that caused the error is not written to the shifter.
A write collision is normally a slave error because a slave has no control over when a master initiates a
transfer. A master knows when a transfer is in progress, so there is no reason for a master to generate a
write-collision error, although the SPI logic can detect write collisions in both master and slave devices.
The SPI configuration determines the characteristics of a transfer in progress. For a master, a transfer
begins when data is written to SPDR and ends when SPIF is set. For a slave with CPHA equal to zero, a
transfer starts when SS goes low and ends when SS returns high. In this case, SPIF is set at the middle
of the eighth SCK cycle when data is transferred from the shifter to the parallel data register, but the
transfer is still in progress until SS goes high. For a slave with CPHA equal to one, transfer begins when
the SCK line goes to its active level, which is the edge at the beginning of the first SCK cycle. The transfer
ends in a slave in which CPHA equals one when SPIF is set. For a slave, after a byte transfer, SCK must
be in inactive state for at least 2 E-clock cycles before the next byte transfer begins.
7.7 SPI Registers
The three SPI registers, SPCR, SPSR, and SPDR, provide control, status, and data storage functions.
This sub-section provides a description of how these registers are organized.
7.7.1 SPI Control Register
Address:
$0028
Read:
Write:
Reset:
Bit 7
6
5
4
3
2
1
Bit 0
SPIE
SPE
DWOM
MSTR
CPOL
CPHA
SPR1
SPR0
0
0
0
0
0
1
U
U
U = Unaffected
Figure 7-3. SPI Control Register (SPCR)
SPIE — Serial Peripheral Interrupt Enable Bit
0 = SPI interrupt disabled
1 = SPI interrupt enabled
SPE — Serial Peripheral System Enable Bit
0 = SPI off
1 = SPI on
DWOM — Port D Wired-OR Mode Bit
DWOM affects all six port D pins.
0 = Normal CMOS outputs
1 = Open-drain outputs
MSTR — Master Mode Select Bit
0 = Slave mode
1 = Master mode
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
81
Serial Peripheral Interface (SPI)
CPOL — Clock Polarity Bit
When the clock polarity bit is cleared and data is not being transferred, the SCK pin of the master
device has a steady state low value. When CPOL is set, SCK idles high. Refer to Figure 7-2 and 7.4
Clock Phase and Polarity Controls.
CPHA — Clock Phase Bit
The clock phase bit, in conjunction with the CPOL bit, controls the clock-data relationship between
master and slave. The CPHA bit selects one of two different clocking protocols. Refer to Figure 7-2
and 7.4 Clock Phase and Polarity Controls.
SPR1 and SPR0 — SPI Clock Rate Select Bits
These two serial peripheral rate bits select one of four baud rates to be used as SCK if the device is a
master; however, they have no effect in the slave mode.
Table 7-1. SPI Clock Rates
SPR1
and SPR0
E Clock
Divide By
Frequency at
E = 2 MHz (Baud)
00
2
1.0 MHz
01
4
500 kHz
10
16
125 kHz
11
32
62.5 kHz
7.7.2 SPI Status Register
Address:
Read:
Write:
Reset:
$0029
Bit 7
6
5
4
3
2
1
Bit 0
SPIF
WCOL
0
MODF
0
0
0
0
0
0
0
0
0
0
0
0
Figure 7-4. SPI Status Register (SPSR)
SPIF — SPI Transfer Complete Flag
SPIF is set upon completion of data transfer between the processor and the external device. If SPIF
goes high, and if SPIE is set, a serial peripheral interrupt is generated. To clear the SPIF bit, read the
SPSR with SPIF set, then access the SPDR. Unless SPSR is read (with SPIF set) first, attempts to
write SPDR are inhibited.
WCOL — Write Collision Bit
Clearing the WCOL bit is accomplished by reading the SPSR (with WCOL set) followed by an access
of SPDR. Refer to 7.5.4 Slave Select (SS) and 7.6 SPI System Errors.
0 = No write collision
1 = Write collision
Bit 5 — Not implemented
Always reads 0.
MODF — Mode Fault Bit
To clear the MODF bit, read the SPSR (with MODF set), then write to the SPCR. Refer to 7.5.4 Slave
Select (SS) and 7.6 SPI System Errors.
0 = No mode fault
1 = Mode fault
MC68HC711D3 Data Sheet, Rev. 2.1
82
Freescale Semiconductor
SPI Registers
Bits 3–0 — Not implemented
Always reads 0
7.7.3 SPI Data I/O Register
The SPI data I/O register (SPDR) is used when transmitting or receiving data on the serial bus. Only a
write to this register initiates transmission or reception of a byte, and this only occurs in the master device.
At the completion of transferring a byte of data, the SPIF status bit is set in both the master and slave
devices.
A read of the SPDR is actually a read of a buffer. To prevent an overrun and the loss of the byte that
caused the overrun, the first SPIF must be cleared by the time a second transfer of data from the shift
register to the read buffer is initiated.
Address:
Read:
Write:
Reset:
$002A
Bit 7
6
5
4
3
2
1
Bit 0
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Unaffected by reset
Figure 7-5. SPI Data I/O Register (SPDR)
NOTE
SPI is double buffered in and single buffered out.
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
83
Serial Peripheral Interface (SPI)
MC68HC711D3 Data Sheet, Rev. 2.1
84
Freescale Semiconductor
Chapter 8
Programmable Timer
8.1 Introduction
The M68HC11 timing system is composed of five clock divider chains. The main clock divider chain
includes a 16-bit free-running counter, which is driven by a programmable prescaler. The main timer's
programmable prescaler provides one of the four clocking rates to drive the 16-bit counter. Two prescaler
control bits select the prescale rate.
The prescaler output divides the system clock by 1, 4, 8, or 16. Taps off of this main clocking chain drive
circuitry that generates the slower clocks used by the pulse accumulator, the real-time interrupt (RTI), and
the computer operating properly (COP) watchdog subsystems. Refer to Figure 8-1.
All main timer system activities are referenced to this free-running counter. The counter begins
incrementing from $0000 as the microcontroller unit (MCU) comes out of reset, and continues to the
maximum count, $FFFF. At the maximum count, the counter rolls over to $0000, sets an overflow flag,
and continues to increment. As long as the MCU is running in a normal operating mode, there is no way
to reset, change, or interrupt the counting. The capture/compare subsystem features three input capture
channels, four output compare channels, and one channel that can be selected to perform either input
capture or output compare. Each of the three input capture functions has its own 16-bit input capture
register (time capture latch) and each of the output compare functions has its own 16-bit compare register.
All timer functions, including the timer overflow and RTI have their own interrupt controls and separate
interrupt vectors.
The pulse accumulator contains an 8-bit counter and edge select logic. The pulse accumulator can
operate in either event counting or gated time accumulation modes. During event counting mode, the
pulse accumulator's 8-bit counter increments when a specified edge is detected on an input signal. During
gated time accumulation mode, an internal clock source increments the 8-bit counter while an input signal
has a predetermined logic level.
RTI is a programmable periodic interrupt circuit that permits pacing the execution of software routines by
selecting one of four interrupt rates.
The COP watchdog clock input (E÷215) is tapped off of the free-running counter chain. The COP
automatically times out unless it is serviced within a specific time by a program reset sequence. If the COP
is allowed to time out, a reset is generated, which drives the RESET pin low to reset the MCU and the
external system. Refer to Table 8-1 for crystal related frequencies and periods.
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
85
Programmable Timer
OSCILLATOR AND
CLOCK GENERATOR
(DIVIDE BY FOUR)
AS
E CLOCK
INTERNAL BUS CLOCK (PH2)
PRESCALER
(÷ 2, 4, 16, 32)
SPR1 AND SPR0
SPI
PRESCALER
(÷ 1, 2, 4,....128)
SCR2–SCR0
PRESCALER
(÷ 1, 3, 4, 13)
SCP1 AND SCP0
SCI RECEIVER CLOCK
÷16
6
E÷2
SCI TRANSMIT CLOCK
PULSE ACCUMULATOR
PRESCALER
(÷ 1, 2, 4, 8)
RTR1 AND RTR0
E ÷ 213
÷4
PRESCALER
(÷ 1, 4, 8, 16)
PR1 AND PR0
REAL-TIME INTERRUPT
E÷215
PRESCALER
(÷1, 4, 16, 64)
CR1 AND CR0
TOF
FF1
TCNT
FF2
S
Q
R
Q
S
Q
R
Q
FORCE
COP
RESET
IC/OC
CLEAR COP
TIMER
SYSTEM
RESET
Figure 8-1. Timer Clock Divider Chains
MC68HC711D3 Data Sheet, Rev. 2.1
86
Freescale Semiconductor
Timer Structure
Table 8-1. Timer Summary
Control
Bits
4.0 MHz
1.0 MHz
1000 ns
PR1 and PR0
XTAL Frequencies
8.0 MHz
12.0 MHz
2.0 MHz
3.0 MHz
500 ns
333 ns
Main Timer Count Rates
Other Rates
(E)
(1/E)
00
1 count —
overflow —
1.0 µs
65.536 ms
500 ns
32.768 ms
333 ns
21.845 ms
(E/1)
(E/216)
01
1 count —
overflow —
4.0 µs
262.14 ms
2.0 µs
131.07 ms
1.333 µs
87.381 ms
(E/4)
(E/218)
10
1 count —
overflow —
8.0 µs
524.29 ms
4.0 µs
262.14 ms
2.667 µs
174.76 ms
(E/8)
(E/219)
11
1 count —
overflow —
16.0 µs
1.049 s
8.0 µs
524.29 ms
5.333 µs
349.52 ms
(E/16)
(E/220)
8.2 Timer Structure
Figure 8-2 shows the capture/compare system block diagram. The port A pin control block includes logic
for timer functions and for general-purpose input/output (I/O). For pins PA2, PA1, and PA0, this block
contains both the edge-detection logic and the control logic that enables the selection of which edge
triggers an input capture. The digital level on PA2–PA0 can be read at any time (read PORTA register),
even if the pin is being used for the input capture function. Pins PA6–PA4 are used for either
general-purpose output or as output compare pins. Pin PA3 can be used for general-purpose I/O, input
capture 4, output compare 5, or output compare 1. When one of these pins is being used for an output
compare function, it cannot be written directly as if it were a general-purpose output. Each of the output
compare functions (OC5–OC2) is related to one of the port A output pins. Output compare 1 (OC1) has
extra control logic, allowing it optional control of any combination of the PA7–PA3 pins. The PA7 pin can
be used as a general-purpose I/O pin, as an input to the pulse accumulator, or as an OC1 output pin.
8.3 Input Capture
The input capture function records the time an external event occurs by latching the value of the
free-running counter when a selected edge is detected at the associated timer input pin. Software can
store latched values and use them to compute the periodicity and duration of events. For example, by
storing the times of successive edges of an incoming signal, software can determine the period and pulse
width of a signal. To measure period, two successive edges of the same polarity are captured. To
measure pulse width, two alternate polarity edges are captured.
In most cases, input capture edges are asynchronous to the internal timer counter, which is clocked
relative to the PH2 clock. These asynchronous capture requests are synchronized to PH2 so that the
latching occurs on the opposite half cycle of PH2 from when the timer counter is being incremented. This
synchronization process introduces a delay from when the edge occurs to when the counter value is
detected. Because these delays offset each other when the time between two edges is being measured,
the delay can be ignored. When an input capture is being used with an output compare, there is a similar
delay between the actual compare point and when the output pin changes state.
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
87
Programmable Timer
MCU E
CLOCK
TCNT (HI)
PRESCALER — DIVIDE BY
1, 4, 8, 16
PR1
16-BIT FREE RUNNING
COUNTER
PR0
TOI
16-BIT COMPARATOR =
OC1F
TOC1 (LO)
9
TOF
TAPS FOR RTL,
COP WATCHDOG,
AND PULSE ACCUMULATOR
16-BIT TIMER BUS
TOC1 (HI)
TCNT (LO)
FORCE
OUTPUT
COMPARE
INTERRUPT REQUESTS
(FURTHER QUALIFIED
BY I BIT IN CCR)
TO PULSE
ACCUMULATOR
OC1I
FOC1
OC2I
16-BIT COMPARATOR =
TOC2 (HI)
TOC2 (LO)
TOC3 (LO)
OC5
16-BIT COMPARATOR =
TI4/O5 (LO)
I4/O5F
CLK
IC2I
CLK
BIT 3
PA3/IC4/
OC5/OC1
BIT 2
PA2/IC1
BIT 1
PA1/IC2
BIT 0
PA0/IC3
3
2
IC2F
TIC2 (LO)
16-BIT LATCH
TIC3 (HI)
CLK
IC1I
IC1F
TIC1 (LO)
16-BIT LATCH
TIC2 (HI)
PA4/OC4/
OC1
4
FOC5
CFORC
TIC1 (HI)
BIT 4
IC4
I4/O5
CLK
PA5/OC3/
OC1
5
FOC4
I4/O5I
16-BIT LATCH
BIT 5
OC4F
TOC4 (LO)
16-BIT LATCH
PA6/OC2/
OC1
6
FOC3
16-BIT COMPARATOR =
TI4/O5 (HI)
BIT 6
OC3F
OC4I
TOC4 (HI)
PA7/OC1/
PAI
7
FOC2
16-BIT COMPARATOR =
PORT A
PINS
BIT 7
OC2F
OC3I
TOC3 (HI)
8
IC3I
IC3F
1
TIC3 (LO)
TFLG 1
STATUS
FLAGS
TMSK 1
INTERRUPT
ENABLES
PORT A
PIN
CONTROL
Figure 8-2. Capture/Compare Block Diagram
The control and status bits that implement the input capture functions are contained in the PACTL,
TCTL2, TMSK1, and TFLG1 registers.
To configure port A bit 3 as an input capture, clear the DDRA3 bit of the PACTL register. Note that this bit
is cleared out of reset. To enable PA3 as the fourth input capture, set the I4/O5 bit in the PACTL register.
Otherwise, PA3 is configured as a fifth output compare out of reset, with bit I4/O5 being cleared. If the
DDRA3 bit is set (configuring PA3 as an output), and IC4 is enabled, then writes to PA3 cause edges on
the pin to result in input captures. Writing to TI4/O5 has no effect when the TI4/O5 register is acting as IC4.
MC68HC711D3 Data Sheet, Rev. 2.1
88
Freescale Semiconductor
Input Capture
8.3.1 Timer Control 2 Register
Use the control bits of timer control 2 register (TCTL2) to program input capture functions to detect a
particular edge polarity on the corresponding timer input pin. Each of the input capture functions can be
independently configured to detect rising edges only, falling edges only, any edge (rising or falling), or to
disable the input capture function. The input capture functions operate independently of each other and
can capture the same TCNT value if the input edges are detected within the same timer count cycle.
Address:
Read:
Write:
Reset:
$0021
Bit 7
6
5
4
3
2
1
Bit 0
EDG4B
EDG4A
EDG1B
EDG1A
EDG2B
EDG2A
EDG3B
EDG3A
0
0
0
0
0
0
0
0
Figure 8-3. Timer Control 2 Register (TCTL2)
EDGxB and EDGxA — Input Capture Edge Control
There are four pairs of these bits. Each pair is cleared to 0 by reset and must be encoded to configure
the corresponding input capture edge detector circuit. IC4 functions only if the I4/O5 bit in PACTL is
set. Refer to Table 8-2 for timer control configuration.
Table 8-2. Timer Control Configuration
EDGxB
EDGxA
Configuration
0
0
Capture disabled
0
1
Capture on rising edges only
1
0
Capture on falling edges only
1
1
Capture on any edge
8.3.2 Timer Input Capture Registers
When an edge has been detected and synchronized, the 16-bit free-running counter value is transferred
into the input capture register pair as a single 16-bit parallel transfer. Timer counter value captures and
timer counter incrementing occur on opposite half-cycles of the phase two clock so that the count value
is stable whenever a capture occurs. The timer input capture (TICx) registers are not affected by reset.
Input capture values can be read from a pair of 8-bit read-only registers. A read of the high-order byte of
an input capture register pair inhibits a new capture transfer for one bus cycle. If a double-byte read
instruction, such as LDD, is used to read the captured value, coherency is assured. When a new input
capture occurs immediately after a high-order byte read, transfer is delayed for an additional cycle but the
value is not lost.
Address: $0010 — TIC1 (High)
Bit 15
14
13
Read:
Bit 15
Bit 14
Bit 13
Write:
Reset:
= Unimplemented
12
Bit 12
11
Bit 11
10
Bit 10
9
Bit 9
Bit 8
Bit 8
Unaffected by reset
Figure 8-4. Timer Input Capture Registers (TICx)
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
89
Programmable Timer
Address: $0011 — TIC1 (Low)
Bit 7
6
5
Read:
Bit 7
Bit 6
Bit 5
Write:
Reset:
Address: $0012 — TIC2 (High)
Bit 15
14
13
Read:
Bit 15
Bit 14
Bit 13
Write:
Reset:
Address: $0013 — TIC2 (Low)
Bit 7
6
5
Read:
Bit 7
Bit 6
Bit 5
Write:
Reset:
Address: $0014 — TIC3 (High)
Bit 15
14
13
Read:
Bit 15
Bit 14
Bit 13
Write:
Reset:
Address: $0015 — TIC3 (Low)
Bit 7
6
5
Read:
Bit 7
Bit 6
Bit 5
Write:
Reset:
= Unimplemented
4
Bit 4
3
Bit 3
2
Bit 2
1
Bit 1
Bit 0
Bit 0
10
Bit 10
9
Bit 9
Bit 8
Bit 8
2
Bit 2
1
Bit 1
Bit 0
Bit 0
10
Bit 10
9
Bit 9
Bit 8
Bit 8
2
Bit 2
1
Bit 1
Bit 0
Bit 0
Unaffected by reset
12
Bit 12
11
Bit 11
Unaffected by reset
4
Bit 4
3
Bit 3
Unaffected by reset
12
Bit 12
11
Bit 11
Unaffected by reset
4
Bit 4
3
Bit 3
Unaffected by reset
Figure 8-4. Timer Input Capture Registers (TICx) (Continued)
8.3.3 Timer Input Capture 4/Output Compare 5 Register
Use timer input capture 4/output compare 5 (TI4/O5) as either an input capture register or an output
compare register, depending on the function chosen for the I4/O5 pin. To enable it as an input capture
pin, set the I4/O5 bit in the pulse accumulator control register (PACTL) to logic level 1. To use it as an
output compare register, set the I4/O5 bit to a logic level 0. Refer to 8.7 Pulse Accumulator.
Address: $001E — TI4/O5 (High)
Bit 15
14
13
Read:
Bit 15
Bit 14
Bit 13
Write:
Reset:
1
1
1
Address: $001F — TI4/O5 (Low)
Bit 7
6
5
Read:
Bit 7
Bit 6
Bit 5
Write:
Reset:
1
1
1
= Unimplemented
12
Bit 12
11
Bit 11
10
Bit 10
9
Bit 9
Bit 8
Bit 8
1
1
1
1
1
4
Bit 4
3
Bit 3
2
Bit 2
1
Bit 1
Bit 0
Bit 0
1
1
1
1
1
Figure 8-5. Timer Input Capture 4/Output
Compare 5 Register (TI4/O5)
MC68HC711D3 Data Sheet, Rev. 2.1
90
Freescale Semiconductor
Output Compare (OC)
8.4 Output Compare (OC)
Use the output compare (OC) function to program an action to occur at a specific time — when the 16-bit
counter reaches a specified value. For each of the five output compare functions, there is a separate
16-bit compare register and a dedicated 16-bit comparator. The value in the compare register is
compared to the value of the free-running counter on every bus cycle. When the compare register
matches the counter value, an output compare status flag is set. The flag can be used to initiate the
automatic actions for that output compare function.
To produce a pulse of a specific duration, write to the output compare register a value representing the
time the leading edge of the pulse is to occur. The output compare circuit is configured to set the
appropriate output either high or low, depending on the polarity of the pulse being produced. After a match
occurs, the output compare register is reprogrammed to change the output pin back to its inactive level
at the next match. A value representing the width of the pulse is added to the original value, and then is
written to the output compare register. Because the pin state changes occur at specific values of the
free-running counter, the pulse width can be controlled accurately at the resolution of the free-running
counter, independent of software latencies. To generate an output signal of a specific frequency and duty
cycle, repeat this pulse-generating procedure.
There are four 16-bit read/write output compare registers: TOC1, TOC2, TOC3, and TOC4, and the
TI4/O5 register, which functions under software control as either IC4 or OC5. Each of the OC registers is
set to $FFFF on reset. A value written to an OC register is compared to the free-running counter value
during each E-clock cycle. If a match is found, the particular output compare flag is set in timer interrupt
flag register 1 (TFLG1). If that particular interrupt is enabled in the timer interrupt mask register 1
(TMSK1), an interrupt is generated. In addition to an interrupt, a specified action can be initiated at one
or more timer output pins. For OC5–OC2, the pin action is controlled by pairs of bits (OMx and OLx) in
the TCTL1 register. The output action is taken on each successful compare, regardless of whether the
OCxF flag in the TFLG1 register was previously cleared.
OC1 is different from the other output compares in that a successful OC1 compare can affect any or all
five of the OC pins. The OC1 output action taken when a match is found is controlled by two 8-bit registers
with three bits unimplemented: the output compare 1 mask register, OC1M, and the output compare 1
data register, OC1D. OC1M specifies which port A outputs are to be used, and OC1D specifies what data
is placed on these port pins.
8.4.1 Timer Output Compare Registers
All output compare registers are 16-bit read-write. Each is initialized to $FFFF at reset. If an output
compare register is not used for an output compare function, it can be used as a storage location. A write
to the high-order byte of an output compare register pair inhibits the output compare function for one bus
cycle. This inhibition prevents inappropriate subsequent comparisons. Coherency requires a complete
16-bit read or write. However, if coherency is not needed, byte accesses can be used.
For output compare functions, write a comparison value to output compare registers TOC1–TOC4 and
TI4/O5. When TCNT value matches the comparison value, specified pin actions occur.
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
91
Programmable Timer
Address: $0016 — TOC1 (High)
Bit 15
14
Read:
Bit 15
Bit 14
Write:
Reset:
1
1
Address: $0017 — TOC1 (Low)
Bit 7
6
Read:
Bit 7
Bit 6
Write:
Reset:
1
1
Address:
Read:
Write:
Reset:
$0018 — TOC2 (High)
Bit 15
14
13
12
11
10
9
Bit 8
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
1
1
1
1
1
1
5
4
3
2
1
Bit 0
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
1
1
1
1
1
1
13
12
11
10
9
Bit 8
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
1
1
1
1
1
1
1
1
5
4
3
2
1
Bit 0
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
1
1
1
1
1
1
13
12
11
10
9
Bit 8
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
1
1
1
1
1
1
5
4
3
2
1
Bit 0
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
1
1
1
1
1
1
13
12
11
10
9
Bit 8
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
1
1
1
1
1
1
5
4
3
2
1
Bit 0
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
1
1
1
1
1
1
Address: $0019 — TOC2 (Low)
Bit 7
6
Read:
Bit 7
Bit 6
Write:
Reset:
1
1
Address: $001A — TOC3 (High)
Bit 15
14
Read:
Bit 15
Bit 14
Write:
Reset:
1
1
Address: $001B — TOC3 (Low)
Bit 7
6
Read:
Bit 7
Bit 6
Write:
Reset:
1
1
Address: $001C — TOC4 (High)
Bit 15
14
Read:
Bit 15
Bit 14
Write:
Reset:
1
1
Address: $001D — TOC4 (Low)
Bit 7
6
Read:
Bit 7
Bit 6
Write:
Reset:
1
1
Figure 8-6. Timer Output Capture Registers (TOCx)
MC68HC711D3 Data Sheet, Rev. 2.1
92
Freescale Semiconductor
Output Compare (OC)
8.4.2 Timer Compare Force Register
The timer compare force register (CFORC) allows forced early compares. FOC1–FOC5 correspond to
the five output compares. These bits are set for each output compare that is to be forced. The action taken
as a result of a forced compare is the same as if there were a match between the OCx register and the
free-running counter, except that the corresponding interrupt status flag bits are not set. The forced
channels trigger their programmed pin actions to occur at the next timer count transition after the write to
CFORC.
The CFORC bits should not be used on an output compare function that is programmed to toggle its
output on a successful compare because a normal compare that occurs immediately before or after the
force can result in an undesirable operation.
Address:
Read:
Write:
Reset:
$000B
Bit 7
6
5
4
3
2
1
Bit 0
FOC1
FOC2
FOC3
FOC4
FOC5
0
0
0
0
0
0
0
0
0
0
0
Figure 8-7. Timer Compare Force Register (CFORC)
FOC1–FOC5 — Write 1s to Force Compare Bits
0 = Not affected
1 = Output x action occurs
Bits 2–0 — Not implemented, always read 0.
8.4.3 Output Compare 1 Mask Register
Use OC1M with OC1 to specify the bits of port A that are affected by a successful OC1 compare. The bits
of the OC1M register correspond to PA7–PA3.
Address:
Read:
Write:
Reset:
$000C
Bit 7
6
5
4
3
2
1
Bit 0
OC1M7
OC1M6
OC1M5
OC1M4
OC1M3
0
0
0
0
0
0
0
0
0
0
0
Figure 8-8. Output Compare 1 Mask Register (OC1M)
OC1M7–OC1M3 — Output Compare Masks
0 = OC1 disabled
1 = OC1 enabled to control the corresponding pin of port A
Bits 2–0 — Not implemented; always read 0.
Set bit(s) to enable OC1 to control corresponding pin(s) of port A.
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
93
Programmable Timer
8.4.4 Output Compare 1 Data Register
Use this register with OC1 to specify the data that is to be stored on the affected pin of port A after a
successful OC1 compare. When a successful OC1 compare occurs, a data bit in OC1D is stored in the
corresponding bit of port A for each bit that is set in OC1M.
Address:
Read:
Write:
Reset:
$000D
Bit 7
6
5
4
3
2
1
Bit 0
OC1D7
OC1D6
OC1D5
OC1D4
OC1D3
0
0
0
0
0
0
0
0
0
0
0
Figure 8-9. Output Compare 1 Data Register (OC1D)
If OC1Mx is set, data in OC1Dx is output to port A bit x on successful OC1 compares.
Bits 2–0 — Not implemented; always read 0.
8.4.5 Timer Counter Register
The 16-bit read-only timer count register (TCNT) contains the prescaled value of the 16-bit timer. A full
counter read addresses the most significant byte (MSB) first. A read of this address causes the least
significant byte (LSB) to be latched into a buffer for the next CPU cycle so that a double-byte read returns
the full 16-bit state of the counter at the time of the MSB read cycle.
Address: $000E — TCNT High
Bit 15
14
Read:
Bit 15
Bit 14
Write:
Reset:
0
0
13
Bit 13
12
Bit 12
11
Bit 11
10
Bit 10
9
Bit 9
Bit 8
Bit 08
0
0
0
0
0
0
4
Bit 4
3
Bit 3
2
Bit 2
1
Bit 1
Bit 0
Bit 0
0
0
0
0
0
Address: $000F — TCNT Low
Bit 7
6
5
Read:
Bit 7
Bit 6
Bit 5
Write:
Reset:
0
0
0
= Unimplemented
Figure 8-10. Timer Counter Registers (TCNT)
In normal modes, TCNT is read-only.
MC68HC711D3 Data Sheet, Rev. 2.1
94
Freescale Semiconductor
Output Compare (OC)
8.4.6 Timer Control 1 Register
The bits of the timer control 1 register (TCTL1) specify the action taken as a result of a successful OCx
compare.
Address:
Read:
Write:
Reset:
$0020
Bit 7
6
5
4
3
2
1
Bit 0
OM2
OL2
OM3
OL3
OM4
OL4
OM5
OL5
0
0
0
0
0
0
0
0
Figure 8-11. Timer Control 1 Register (TCTL1)
OM2–OM5 — Output Mode Bits
OL2–OL5 — Output Level Bits
These control bit pairs are encoded to specify the action taken after a successful OCx compare. OC5
functions only if the I4/O5 bit in the PACTL register is clear. Refer to Table 8-3 for the coding.
Table 8-3. Timer Output Compare Actions
OMx
OLx
Action Taken on Successful Compare
0
0
Timer disconnected from output pin logic
0
1
Toggle OCx output line
1
0
Clear OCx output line to 0
1
1
Set OCx output line to 1
8.4.7 Timer Interrupt Mask 1 Register
The timer interrupt mask 1 register (TMSK1) is an 8-bit register used to enable or inhibit the timer input
capture and output compare interrupts.
Address:
Read:
Write:
Reset:
$0022
Bit 7
6
5
4
3
2
1
Bit 0
OC1I
OC2I
OC3I
OC4I
I4/O5I
IC1I
IC2I
IC3I
0
0
0
0
0
0
0
0
Figure 8-12. Timer Interrupt Mask 1 Register (TMSK1)
OC1I–OC4I — Output Compare x Interrupt Enable Bits
If the OCxI enable bit is set when the OCxF flag bit is set, a hardware interrupt sequence is requested.
I4/O5I — Input Capture 4 or Output Compare 5 Interrupt Enable Bit
When I4/O5 in PACTL is one, I4/O5I is the input capture 4 interrupt enable bit. When I4/O5 in PACTL
is 0, I4/O5I is the output compare 5 interrupt enable bit.
IC1I–IC3I — Input Capture x Interrupt Enable Bits
If the ICxI enable bit is set when the ICxF flag bit is set, a hardware interrupt sequence is requested.
NOTE
Bits in TMSK1 correspond bit for bit with flag bits in TFLG1. Ones in TMSK1
enable the corresponding interrupt sources.
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
95
Programmable Timer
8.4.8 Timer Interrupt Flag 1 Register
The timer interrupt flag 1 register (TFLG1) bits indicate when timer system events have occurred. Coupled
with the bits of TMSK1, the bits of TFLG1 allow the timer subsystem to operate in either a polled or
interrupt driven system. Each bit of TFLG1 corresponds to a bit in TMSK1 in the same position.
Address:
Read:
Write:
Reset:
$0023
Bit 7
6
5
4
3
2
1
Bit 0
OC1F
OC2F
OC3F
OC4F
I4/O5F
IC1F
IC2F
IC3F
0
0
0
0
0
0
0
0
Figure 8-13. Timer Interrupt Flag 1 Register (TFLG1)
Clear flags by writing a 1 to the corresponding bit position(s).
OC1F–OC5F — Output Compare x Flag
Set each time the counter matches output compare x value
I4/O5F — Input Capture 4/Output Compare 5 Flag
Set by IC4 or OC5, depending on the function enabled by I4/O5 bit in PACTL
IC1F–IC3F — Input Capture x Flag
Set each time a selected active edge is detected on the ICx input line
8.4.9 Timer Interrupt Mask 2 Register
The timer interrupt mask 1 register (TMSK2) is an 8-bit register used to enable or inhibit timer overflow
and real-time interrupts. The timer prescaler control bits are included in this register.
Address:
Read:
Write:
Reset:
$0024
Bit 7
6
5
4
3
2
1
Bit 0
TOI
RTII
PAOVI
PAII
0
0
PR1
PR0
0
0
0
0
0
0
0
0
Figure 8-14. Timer Interrupt Mask 2 Register (TMSK2)
TOI — Timer Overflow Interrupt Enable Bit
0 = TOF interrupts disabled
1 = Interrupt requested when TOF is set to 1
RTII — Real-Time Interrupt Enable Bit
Refer to 8.5 Real-Time Interrupt.
PAOVI — Pulse Accumulator Overflow Interrupt Enable Bit
Refer to 8.7 Pulse Accumulator.
PAII — Pulse Accumulator Input Edge Interrupt Enable Bit
Refer to 8.7 Pulse Accumulator.
NOTE
Bits in TMSK2 correspond bit for bit with flag bits in TFLG2. Ones in TMSK2
enable the corresponding interrupt sources.
MC68HC711D3 Data Sheet, Rev. 2.1
96
Freescale Semiconductor
Output Compare (OC)
PR1 and PR0 — Timer Prescaler Select Bits
These bits are used to select the prescaler divide-by ratio. In normal modes, PR1 and PR0 can be
written once only, and the write must be within 64 cycles after reset. Refer to Table 8-4 for specific
timing values.
Table 8-4. Timer Prescale
PR1 and PR0
00
01
10
11
Prescaler
1
4
8
16
8.4.10 Timer Interrupt Flag 2 Register
The timer interrupt flag 2 register (TFLG2) bits indicate when certain timer system events have occurred.
Coupled with the four high-order bits of TMSK2, the bits of TFLG2 allow the timer subsystem to operate
in either a polled or interrupt driven system. Each bit of TFLG2 corresponds to a bit in TMSK2 in the same
position.
Address:
Read:
Write:
Reset:
$0025
Bit 7
6
5
4
3
2
1
Bit 0
TOF
RTIF
PAOVF
PAIF
0
0
0
0
0
0
0
0
0
0
0
0
Figure 8-15. Timer Interrupt Flag 2 Register (TFLG2)
Clear flags by writing a 1 to the corresponding bit position(s).
TOF — Timer Overflow Interrupt Flag
Set when TCNT changes from $FFFF to $0000
RTIF — Real-Time (Periodic) Interrupt Flag
Refer to 8.5 Real-Time Interrupt.
PAOVF — Pulse Accumulator Overflow Interrupt Flag
Refer to 8.7 Pulse Accumulator.
PAIF — Pulse Accumulator Input Edge Interrupt Flag
Refer to 8.7 Pulse Accumulator.
Bits 3–0 — Not implemented
Always read 0.
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
97
Programmable Timer
8.5 Real-Time Interrupt
The real-time interrupt feature, used to generate hardware interrupts at a fixed periodic rate, is controlled
and configured by two bits (RTR1 and RTR0) in the pulse accumulator control (PACTL) register. The RTII
bit in the TMSK2 register enables the interrupt capability. The four different rates available are a product
of the MCU oscillator frequency and the value of bits RTR1 and RTR0. Refer to Table 8-5 for the periodic
real-time interrupt rates.
Table 8-5. Periodic Real-Time Interrupt Rates
RTR1
and RTR0
E = 1 MHz
E = 2 MHz
E = 3 MHz
E = X MHz
00
01
10
11
2.731 ms
5.461 ms
10.923 ms
21.845 ms
4.096 ms
8.192 ms
16.384 ms
32.768 ms
8.192 ms
16.384 ms
32.768 ms
65.536 ms
(E/213)
(E/214)
(E/215)
(E/216)
The clock source for the RTI function is a free-running clock that cannot be stopped or interrupted except
by reset. This clock causes the time between successive RTI timeouts to be a constant that is
independent of the software latencies associated with flag clearing and service. For this reason, an RTI
period starts from the previous timeout, not from when RTIF is cleared.
Every timeout causes the RTIF bit in TFLG2 to be set, and if RTII is set, an interrupt request is generated.
After reset, one entire real-time interrupt period elapses before the RTIF flag is set for the first time. Refer
to the TMSK2, TFLG2, and PACTL registers.
8.5.1 Timer Interrupt Mask 2 Register
The timer interrupt mask 2 register (TMSK2) contains the real-time interrupt enable bits.
Address:
Read:
Write:
Reset:
$0024
Bit 7
6
5
4
3
2
1
Bit 0
TOI
RTII
PAOVI
PAII
0
0
PR1
PR0
0
0
0
0
0
0
0
0
Figure 8-16. Timer Interrupt Mask 2 Register (TMSK2)
TOI — Timer Overflow Interrupt Enable Bit
Refer to 8.4 Output Compare (OC).
RTII — Real-Time Interrupt Enable Bit
0 = RTIF interrupts disabled
1 = Interrupt requested
PAOVI — Pulse Accumulator Overflow Interrupt Enable Bit
Refer to 8.7 Pulse Accumulator.
PAII — Pulse Accumulator Input Edge Bit
Refer to 8.7 Pulse Accumulator.
Bits 3–2 — Unimplemented
Always read 0.
MC68HC711D3 Data Sheet, Rev. 2.1
98
Freescale Semiconductor
Real-Time Interrupt
PR1 and PR0 — Timer Prescaler Select Bits
Refer to Table 8-4.
NOTE
Bits in TMSK2 correspond bit for bit with flag bits in TFLG2. Ones in TMSK2
enable the corresponding interrupt sources.
8.5.2 Timer Interrupt Flag 2 Register
Bits of the timer interrupt flag 2 register (TFLG2) indicate the occurrence of timer system events. Coupled
with the four high-order bits of TMSK2, the bits of TFLG2 allow the timer subsystem to operate in either
a polled or interrupt driven system. Each bit of TFLG2 corresponds to a bit in TMSK2 in the same position.
Address:
$0025
Read:
Write:
Reset:
Bit 7
6
5
4
3
2
1
Bit 0
TOF
RTIF
PAOVF
PAIF
0
0
0
0
0
0
0
0
0
0
0
0
Figure 8-17. Timer Interrupt Flag 2 Register (TFLG2)
Clear flags by writing a 1 to the corresponding bit position(s).
TOF — Timer Overflow Interrupt Flag
Set when TCNT changes from $FFFF to $0000
RTIF — Real-Time Interrupt Flag
The RTIF status bit is automatically set to 1 at the end of every RTI period. To clear RTIF, write a byte
to TFLG2 with bit 6 set.
PAOVF — Pulse Accumulator Overflow Interrupt Flag
Refer to 8.7 Pulse Accumulator.
PAIF — Pulse Accumulator Input Edge Interrupt Flag
Refer to 8.7 Pulse Accumulator.
Bits 3–0 — Not implemented
Always read 0.
8.5.3 Pulse Accumulator Control Register
Bits RTR1 and RTR0 of the pulse accumulator control register (PACTL) select the rate for the real-time
interrupt system. Bit DDRA3 determines whether port A bit three is an input or an output when used for
general-purpose I/O. The remaining bits control the pulse accumulator.
Address:
$0026
Read:
Write:
Reset:
Bit 7
6
5
4
3
2
1
Bit 0
DDRA7
PAEN
PAMOD
PEDGE
DDRA3
I4/O5
RTR1
RTR0
0
0
0
0
0
0
0
0
Figure 8-18. Pulse Accumulator Control Register (PACTL)
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
99
Programmable Timer
DDRA7 — Data Direction Control for Port A Bit 7
Refer to 8.7 Pulse Accumulator.
PAEN — Pulse Accumulator System Enable Bit
Refer to 8.7 Pulse Accumulator.
PAMOD — Pulse Accumulator Mode Bit
Refer to 8.7 Pulse Accumulator.
PEDGE — Pulse Accumulator Edge Control Bit
Refer to 8.7 Pulse Accumulator.
DDRA3 — Data Direction Register for Port A Bit 3
Refer to Chapter 5 Input/Output (I/O) Ports.
I4/O5 — Input Capture 4/Output Compare 5 Bit
Refer to 8.3 Input Capture.
RTR1 and RTR0 — RTI Interrupt Rate Select Bits
These two bits determine the rate at which the RTI system requests interrupts. The RTI system is
driven by an E divided by 213 rate clock that is compensated so it is independent of the timer prescaler.
These two control bits select an additional division factor. See Table 8-6.
Table 8-6. Real-Time Interrupt Rates
RTR1
and RTR0
E = 1 MHz
E = 2 MHz
E = 3 MHz
E = X MHz
00
01
10
11
2.731 ms
5.461 ms
10.923 ms
21.845 ms
4.096 ms
8.192 ms
16.384 ms
32.768 ms
8.192 ms
16.384 ms
32.768 ms
65.536 ms
(E/213)
(E/214)
(E/215)
(E/216)
8.6 Computer Operating Properly Watchdog Function
The clocking chain for the COP function, tapped off of the main timer divider chain, is only superficially
related to the main timer system. The CR1 and CR0 bits in the OPTION register and the NOCOP bit in
the CONFIG register determine the status of the COP function. Refer to Chapter 4 Resets, Interrupts, and
Low-Power Modes for a more detailed discussion of the COP function.
8.7 Pulse Accumulator
The MC68HC711D3 has an 8-bit counter that can be configured to operate either as a simple event
counter or for gated time accumulation, depending on the state of the PAMOD bit in the PACTL register.
Refer to the pulse accumulator block diagram, Figure 8-19.
In the event counting mode, the 8-bit counter is clocked to increasing values by an external pin. The
maximum clocking rate for the external event counting mode is the E clock divided by two. In gated time
accumulation mode, a free-running E-clock ÷ 64 signal drives the 8-bit counter, but only while the external
PAI pin is activated. Refer to Table 8-7. The pulse accumulator counter can be read or written at any time.
Pulse accumulator control bits are also located within two timer registers, TMSK2 and TFLG2, as
described here.
MC68HC711D3 Data Sheet, Rev. 2.1
100
Freescale Semiconductor
Pulse Accumulator
1
INTERRUPT
REQUESTS
TMSK2 INT ENABLES
PAIF
PAOVF
PAII
PAOVI
2
TFLG2 INTERRUPT STATUS
PAI EDGE
DISABLE
FLAG SETTING
E ÷ 64 CLOCK
(FROM MAIN TIMER)
INPUT BUFFER
AND
EDGE DETECTION
PA7/
PAI/OC1
PACNT
8-BIT COUNTER
ENABLE
OUTPUT
BUFFER
PEDGE
PAMOD
PAEN
PAEN
DDRA7
FROM
MAIN TIMER
OC1
OVERFLOW
2:1
MUX
PACTL CONTROL
INTERNAL
DATA BUS
Figure 8-19. Pulse Accumulator
Table 8-7. Pulse Accumulator Timing in Gated Mode
Common XTAL Frequencies
Selected
Crystal
4.0 MHz
8.0 MHz
12.0 MHz
CPU Clock
(E)
1.0 MHz
2.0 MHz
3.0 MHz
Cycle Time
(1/E)
1000 ns
500 ns
333 ns
1 count overflow -
64.0 µs
16.384 ms
32.0 µs
8.192 ms
21.33 µs
5.461 ms
6
(E/2 )
(E/214)
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
101
Programmable Timer
8.7.1 Pulse Accumulator Control Register
Four of the pulse accumulator control register (PACTL) bits control an 8-bit pulse accumulator system.
Another bit enables either the OC5 function or the IC4 function, while two other bits select the rate for the
real-time interrupt system.
Address:
Read:
Write:
Reset:
$0026
Bit 7
6
5
4
3
2
1
Bit 0
DDRA7
PAEN
PAMOD
PEDGE
DDRA3
I4/O5
RTR1
RTR0
0
0
0
0
0
0
0
0
Figure 8-20. Pulse Accumulator Control Register (PACTL)
DDRA7 — Data Direction Control for Port A Bit 7
The pulse accumulator uses port A bit 7 as the PAI input, but the pin can also be used as
general-purpose I/O or as an output compare.
NOTE
Even when port A bit 7 is configured as an output, the pin still drives the
input to the pulse accumulator.
Refer to Chapter 5 Input/Output (I/O) Ports for more information.
PAEN — Pulse Accumulator System Enable Bit
0 = Pulse accumulator disabled
1 = Pulse accumulator enabled
PAMOD — Pulse Accumulator Mode Bit
0 = Event counter
1 = Gated time accumulation
PEDGE — Pulse Accumulator Edge Control Bit
This bit has different meanings depending on the state of the PAMOD bit, as shown in Table 8-8.
Table 8-8. Pulse Accumulator Edge Control
PAMOD
PEDGE
Action on Clock
0
0
PAI falling edge increments the counter.
0
1
PAI rising edge increments the counter.
1
0
A 0 on PAI inhibits counting.
1
1
A 1 on PAI inhibits counting.
DDRA3 — Data Direction Register for Port A Bit 3
Refer to Chapter 5 Input/Output (I/O) Ports.
I4/O5 — Input Capture 4/Output Compare 5 Bit
Refer to 8.3 Input Capture.
RTR1 and RTR0 — RTI Interrupt Rate Select Bits
Refer to 8.5 Real-Time Interrupt.
MC68HC711D3 Data Sheet, Rev. 2.1
102
Freescale Semiconductor
Pulse Accumulator
8.7.2 Pulse Accumulator Count Register
The 8-bit read/write pulse accumulator count register (PACNT) contains the count of external input events
at the PAI input or the accumulated count. The counter is not affected by reset and can be read or written
at any time. Counting is synchronized to the internal PH2 clock so that incrementing and reading occur
during opposite half cycles.
Address:
Read:
Write:
Reset:
$0027
Bit 7
6
5
4
3
2
1
Bit 0
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Unaffected by reset
Figure 8-21. Pulse Accumulator Count Register (PACNT)
8.7.3 Pulse Accumulator Status and Interrupt Bits
The pulse accumulator control bits, PAOVI and PAII, PAOVF, and PAIF are located within timer registers
TMSK2 and TFLG2.
PAOVI and PAOVF — Pulse Accumulator Interrupt Enable and Overflow Flag
The PAOVF status bit is set each time the pulse accumulator count rolls over from $FF to $00. To clear
this status bit, write a 1 in the corresponding data bit position (bit 5) of the TFLG2 register. The PAOVI
control bit allows configuring the pulse accumulator overflow for polled or interrupt-driven operation
and does not affect the state of PAOVF. When PAOVI is 0, pulse accumulator overflow interrupts are
inhibited, and the system operates in a polled mode, which requires PAOVF to be polled by user
software to determine when an overflow has occurred. When the PAOVI control bit is set, a hardware
interrupt request is generated each time PAOVF is set. Before leaving the interrupt service routine,
software must clear PAOVF by writing to the TFLG2 register.
PAII and PAIF — Pulse Accumulator Input Edge Interrupt Enable and Flag
The PAIF status bit is automatically set each time a selected edge is detected at the PA7/PAI/OC1 pin.
To clear this status bit, write to the TFLG2 register with a 1 in the corresponding data bit position (bit
4). The PAII control bit allows configuring the pulse accumulator input edge detect for polled or
interrupt-driven operation but does not affect setting or clearing the PAIF bit. When PAII is 0, pulse
accumulator input interrupts are inhibited, and the system operates in a polled mode. In this mode, the
PAIF bit must be polled by user software to determine when an edge has occurred. When the PAII
control bit is set, a hardware interrupt request is generated each time PAIF is set. Before leaving the
interrupt service routine, software must clear PAIF by writing to the TFLG register.
Address:
Read:
Write:
Reset:
$0024
Bit 7
6
5
4
3
2
1
Bit 0
TOI
RTII
PAOVI
PAII
0
0
PR1
PR0
0
0
0
0
0
0
0
0
Figure 8-22. Timer Interrupt Mask 2 Register (TMSK2)
Address:
Read:
Write:
Reset:
$0025
Bit 7
6
5
4
3
2
1
Bit 0
TOF
RTIF
PAOVF
PAIF
0
0
0
0
0
0
0
0
0
0
0
0
Figure 8-23. Timer Interrupt Flag 2 Register (TFLG2)
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
103
Programmable Timer
MC68HC711D3 Data Sheet, Rev. 2.1
104
Freescale Semiconductor
Chapter 9
Electrical Characteristics
9.1 Introduction
This section contains electrical specifications.
9.2 Maximum Ratings
Maximum ratings are the extreme limits to which the microcontroller unit (MCU) can be exposed without
permanently damaging it.
NOTE
This device is not guaranteed to operate properly at the maximum ratings.
Refer to 9.5 DC Electrical Characteristics for guaranteed operating
conditions.
Rating
Symbol
Value
Unit
Supply voltage
VDD
–0.3 to +7.0
V
Input voltage
VIn
–0.3 to +7.0
V
Current drain per pin(1)
Excluding VDD, VSS, VRH, and VRL
ID
25
mA
TSTG
–55 to +150
°C
Storage temperature
1. One pin at a time, observing maximum power dissipation limits
NOTE
This device contains circuitry to protect the inputs against damage due to
high static voltages or electric fields; however, it is advised that normal
precautions be taken to avoid application of any voltage higher than
maximum-rated voltages to this high-impedance circuit. For proper
operation, it is recommended that VIn and VOut be constrained to the range
VSS ≤ (VIn or VOut) ≤ VDD. Reliability of operation is enhanced if unused
inputs are connected to an appropriate logic voltage level (for example,
either VSS or VDD).
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
105
Electrical Characteristics
9.3 Functional Operating Temperature Range
Rating
Symbol
Value
Unit
TA
TL to TH
–40 to +85
–40 to +105
°C
Symbol
Value
Unit
Average junction temperature
TJ
TA + (PD × ΘJA)
°C
Ambient temperature
TA
User-determined
°C
Package thermal resistance (junction-to-ambient)
40-pin plastic dual in-line package (DIP)
44-pin plastic leaded chip carrier (PLCC)
44-pin plastic quad flat pack (QFP)
ΘJA
50
50
85
°C/W
Total power dissipation(1)
PD
PINT + PI/O
K / TJ + 273°C
W
Device internal power dissipation
PINT
IDD × VDD
W
I/O pin power dissipation(2)
PI/O
User-determined
W
Operating temperature range
MC68HC711D3
MC68HC711D3V
9.4 Thermal Characteristics
Characteristic
A constant(3)
K
PD × (TA + 273°C)
+ ΘJA × PD2
W/°C
1. This is an approximate value, neglecting PI/O.
2. For most applications, PI/O ≤ PINT and can be neglected.
3. K is a constant pertaining to the device. Solve for K with a known TA and a measured PD (at equilibrium). Use this value
of K to solve for PD and TJ, iteratively, for any value of TA.
MC68HC711D3 Data Sheet, Rev. 2.1
106
Freescale Semiconductor
DC Electrical Characteristics
9.5 DC Electrical Characteristics
Characteristic(1)
Output voltage(2)
ILoad = ± 10.0 µA
All outputs
All outputs except RESET and MODA
Output high voltage(1)
ILoad = – 0.8 mA, VDD = 4.5 V
Output low voltage
ILoad = 1.6 mA
Input high voltage
All outputs except
RESET, EXTAL, and MODA
All outputs except XTAL
All inputs except RESET
RESET
Input low voltage All inputs
I/O ports, three-state leakage PA7, PA3, PC7–PC0, PD7–PD0, VIn = VIH
or VIL
MODA/LIR, RESET
Input leakage current
IRQ, XIRQ
VIn = VDD or VSS
VIn = VDD or VSS
MODB/VSTBY
RAM standby voltage
RAM standby current
Power down
Power down
Symbol
VOL
VOH
Min
Max
Unit
—
VDD – 0.1
0.1
—
V
VOH
VDD – 0.8
—
V
VOL
—
0.4
V
VIL
0.7 x VDD
0.8 x VDD
VSS – 0.3
VDD + 0.3
VDD + 0.3
0.2 x VDD
V
IOZ
—
±10
µA
IIn
—
—
µA
VSB
ISB
4.0
—
±1
±10
VDD
VIH
V
V
µA
20
(3)
Total supply current
RUN:
Single-chip mode
dc — 2 MHz
dc — 3 MHz
Expanded multiplexed mode
dc — 2 MHz
dc — 3 MHz
WAIT — All peripheral functions shut down:
Single-chip mode
dc — 2 MHz
dc — 3 MHz
Expanded multiplexed mode
dc — 2 MHz
dc — 3 MHz
STOP — No clocks, single-chip mode:
dc — 2 MHz
dc — 3 MHz
Input capacitancePA3–PA0, IRQ, XIRQ, EXTAL
PA7, PC7–PC0, PD7–PD0, MODA/LIR, RESET
Power dissipation
Single-chip mode
dc — 2 MHz
dc — 3 MHz
Expanded multiplexed mode
dc — 2 MHz
dc — 3 MHz
EPROM programming voltage
EPROM programming time
IDD
mA
—
—
15
27
—
—
27
35
WIDD
mA
—
—
6
15
—
—
10
20
—
—
100
150
CIn
—
—
8
12
PD
—
—
85
150
mW
VPP
tPP
—
—
11.75
2
150
195
12.75
4
V
ms
SIDD
µA
pF
1. VDD = 5.0 Vdc ±10%, VSS = 0 Vdc, TA = TL to TH, unless otherwise noted.
2. VOH specification for RESET and MODA is not applicable because they are open-drain pins. VOH specification is not
applicable to ports C and D in wired-OR mode.
3. All ports configured as inputs: VIL ≤ 0.2 V, VIH ≤ VDD –0.2 V; no dc loads; EXTAL is driven with a square wave;
tcyc = 476.5 ns.
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
107
Electrical Characteristics
VDD
EQUIVALENT TEST LOAD(1)
Pins
R2
TEST
POINT
C1
R1
R1
R2
C1
PA3–PA7
PB0–PB7
PC0–PC7
PD0, PD5–PD7
E
3.26 K
2.38 K
90 pF
PD1—PD4
3.26 K
2.38 K
200 pF
Note:
1. Full test loads are applied during all ac electrical timing measurements.
Figure 9-1. Equivalent Test Load
CLOCKS,
STROBES
~ VDD
VDD – 0.8 V
0.4 V
0.4 V
~ V SS
NOM
NOM
70% of VDD
INPUTS
20% of VDD
NOMINAL TIMING
~ VDD
VDD – 0.8 V
OUTPUTS
0.4 V
~ VSS
DC TESTING
CLOCKS,
STROBES
~ VDD
70% of VDD
20% of VDD
~ VSS
20% of VDD
SPEC
SPEC
70% of VDD
INPUTS
20% of VDD
(NOTE 1)
VDD – 0.8 V
0.4 V
SPEC TIMING
~ VDD
OUTPUTS
~ VSS
70% of VDD
20% of VDD
AC TESTING
Note:
1. During ac timing measurements, inputs are driven to 0.4 volts and VDD – 0.8 volts while timing measurements are taken
at the 20% and 70% of VDD points.
Figure 9-2. Test Methods
MC68HC711D3 Data Sheet, Rev. 2.1
108
Freescale Semiconductor
Control Timing
9.6 Control Timing
1.0 MHz
Characteristic(1)
2.0 MHz
3.0 MHz
Symbol
Unit
Min
Max
Min
Max
Min
Max
Frequency of operation
fO
dc
1.0
dc
2.0
dc
3.0
MHz
E-clock period
tcyc
1000
—
500
—
333
—
ns
Crystal frequency
fXTAL
—
4.0
—
8.0
—
12.0
MHz
External oscillator frequency
4 fO
dc
4.0
dc
8.0
dc
12.0
MHz
tPCSU
300
—
175
—
133
—
ns
PWRSTL
8
1
—
—
8
1
—
—
8
1
—
—
tcyc
Mode programming setup time
tMPS
2
—
2
—
2
—
tcyc
Mode programming hold time
tMPH
10
—
10
—
10
—
ns
PWIRQ
1020
—
520
—
353
—
ns
tWRS
—
4
—
4
—
4
tcyc
PWTIM
1020
—
520
—
353
—
ns
Processor control setup timetPCSU = 1/4 tcyc + 50 ns
Reset input pulse width(2)
To guarantee external reset vector
Minimum input time can be preempted by internal reset
Interrupt pulse width, PWIRQ = tcyc + 20 ns
IRQ edge-sensitive mode
Wait recovery startup time
Timer pulse width PWTIM = tcyc + 20 ns
Input capture pulse
Accumulator input
1. VDD = 5.0 Vdc ± 10%, VSS = 0 Vdc, TA = TL to TH. All timing is shown with respect to 20% VDD and 70% VDD, unless
otherwise noted.
2. Reset is recognized during the first clock cycle it is held low. Internal circuitry then drives the pin low for four clock cycles,
releases the pin, and samples the pin level two cycles later to determine the source of the interrupt. Refer to Chapter 5
Input/Output (I/O) Ports for further details.
PA0–PA3(1)
PA0–PA3(2)
PA7(1) (3)
PWTIM
PA7(2) (3)
Notes:
1. Rising edge sensitive input
2. Falling edge sensitive input
3. Maximum pulse accumulator clocking rate is E-clock frequency divided by 2.
Figure 9-3. Timer Inputs
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
109
Electrical Characteristics
110
VDD
EXTAL
MC68HC711D3 Data Sheet, Rev. 2.1
4064 tcyc
E
tPCSU
PWRSTL
RESET
tMPS
tMPH
MODA, MODB
ADDRESS
FFFE
FFFE
FFFE
FFFE
FFFF
NEW
PC
FFFE
FFFE
FFFE
Figure 9-4. POR and External Reset Timing Diagram
FFFE
FFFE
FFFF
NEW
PC
Freescale Semiconductor
Freescale Semiconductor
RESET
IRQ(1)
PWIRQ
IRQ(2)
or XIRQ
MC68HC711D3 Data Sheet, Rev. 2.1
tSTOPDELAY(3)
AS
E
ADDRESS(4)
STOP
ADDR
STOP
ADDR + 1 OPCODE
STOP
ADDR + 1
Resume program with instruction which follows the STOP instruction.
ADDRESS(5)
STOP
ADDR
STOP
ADDR + 1
STOP
ADDR + 1
Notes:
1. Edge sensitive IRQ pin (IRQE bit = 1)
2. Edge sensitive IRQ pin (IRQE bit = 0)
3. tSTOPDELAY = 4064 tcyc if DLY bit = 1 or 4 tcyc if DLY = 0.
4. XIRQ with X bit in CCR = 1.
5. IRQ or (XIRQ with X bit in CCR = 0)
STOP
ADDR + 2
SP – 8
SP – 8
FFF2
(FFF4)
FFF3
(FFF5)
NEW
PC
SP…SP–7
Figure 9-5. STOP Recovery Timing Diagram
Control Timing
111
Electrical Characteristics
112
MC68HC711D3 Data Sheet, Rev. 2.1
E
tPCSU
IRQ, XIRQ,
OR INTERNAL
INTERRUPTS
ADDRESS
tWRS
WAIT
ADDR
WAIT
ADDR + 1
SP
PCL
SP – 1
SP – 2…SP – 8
SP – 8
SP – 8…SP – 8
SP – 8
SP – 8
PCH, YL, YH, XL, XH, A, B, CCR
STACK REGISTERS
R/W
Note: RESET also causes recovery from WAIT.
Figure 9-6. WAIT Recovery Timing Diagram
SP – 8
NEW
PC
VECTOR
ADDR
VECTOR
ADDR + 1
Freescale Semiconductor
Freescale Semiconductor
E
tPCSU
IRQ(1)
PWIRQ
(2)
MC68HC711D3 Data Sheet, Rev. 2.1
IRQ , XIRQ
OR INTERNAL
INTERRUPT
NEXT
OP + 1
ADDRESS
SP
SP – 1
SP – 2
SP – 3
SP – 4
SP – 5
SP – 6
SP – 7
SP – 8
NEW
PC
SP – 8
VECTOR
ADDR
NEXT
OPCODE
VECTOR
ADDR + 1
AS
ADDRESS
OP
CODE
——
PCL
PCH
IYL
IYH
IXL
IXH
B
A
CCR
——
VECT
MSB
VECT
LSB
OP
CODE
R/W
Notes:
1. Edge sensitive IRQ pin (IRQE bit = 1)
2. Level sensitive IRQ pin (IRQE bit = 0)
Figure 9-7. Interrupt Timing Diagram
Control Timing
113
Electrical Characteristics
9.7 Peripheral Port Timing
1.0 MHz
Characteristic(1)
2.0 MHz
3.0 MHz
Symbol
Unit
Min
Max
Min
Max
Min
Max
fO
1.0
1.0
2.0
2.0
3.0
3.0
MHz
E-clock period
tCYC
1000
—
500
—
333
—
ns
Peripheral data setup time(2)
MCU read of ports A, B, C, and D
tPDSU
100
—
100
—
100
—
ns
Peripheral data hold time(2)
MCU read of ports A, B, C, and D
tPDH
50
—
50
—
50
—
ns
Delay time, peripheral data write
MCU write to port A
MCU writes to ports B, C, and D
tPWD = 1/4 tcyc + 150 ns
tPWD
—
200
—
200
—
200
—
350
—
225
—
183
Frequency of operation (E-clock frequency)
ns
1. VDD = 5.0 Vdc ± 10%, VSS = 0 Vdc, TA = TL to TH. All timing is shown with respect to 20% VDD and 70% VDD, unless
otherwise noted.
2. Port C and D timing is valid for active drive (CWOM and DWOM bits not set in PIOC and SPCR registers respectively).
MCU WRITE TO PORT
E
t PWD
PORTS
B, C, D
PREVIOUS PORT DATA
NEW DATA VALID
tPWD
PORT A
PREVIOUS PORT DATA
NEW DATA VALID
Figure 9-8. Port Write Timing Diagram
MCU READ OF PORT
E
tPDSU
tPDH
PORTS
A, B, C, D
Figure 9-9. Port Read Timing Diagram
MC68HC711D3 Data Sheet, Rev. 2.1
114
Freescale Semiconductor
Expansion Bus Timing
9.8 Expansion Bus Timing
Characteristic(1)
Num
Symbol
1.0 MHz
Min
Max
2.0 MHz
3.0 MHz
Min Max Min Max
Unit
Frequency of operation (E-clock frequency)
fO
dc
1.0
dc
2.0
dc
3.0
MHz
1
Cycle time
tcyc
1000
—
500
—
333
—
ns
2
Pulse width, E low, PWEL = 1/2 tcyc — 23 ns
PWEL
477
—
227
—
146
—
ns
3
Pulse width, E high, PWEH = 1/2 tcyc – 28 ns
PWEH
472
—
222
—
141
—
ns
4A
E and AS rise time
tr
—
20
—
20
—
20
ns
4B
E and AS fall time
tf
—
20
—
20
—
15
ns
9
Address hold time(2)a, tAH = 1/8 tcyc – 29.5 ns
tAH
95.5
—
33
—
26
—
ns
12
Non-muxed address valid time to E rise
tAV = PWEL – (tASD + 80 ns)(2)a
tAV
281.5
—
94
—
54
—
ns
17
Read data setup time
tDSR
30
—
30
—
30
—
ns
18
Read data hold time (max = tMAD)
tDHR
0
145.5
0
83
0
51
ns
tDDW
—
190.5
—
128
—
71
ns
ns(2)a
19
Write data delay time, tDDW = 1/8 tcyc + 65.5
21
Write data hold time, tDHW = 1/8 tcyc – 29.5 ns(2)a
tDHW
95.5
—
33
—
26
—
ns
22
Muxed address valid time to E rise
tAVM = PWEL – (tASD + 90 ns)(2)a
tAVM
271.5
—
84
—
54
—
ns
24
Muxed address valid time to AS fall
tASL = PWASH – 70 ns
tASL
151
—
26
—
13
—
ns
25
Muxed address hold time, tAHL = 1/8 tcyc – 29.5 ns(2)b
tAHL
95.5
—
33
—
31
—
ns
26
Delay time, E to AS rise, tASD = 1/8 tcyc – 9.5 ns(2)a
tASD
115.5
—
53
—
31
—
ns
27
Pulse width, AS high, PWASH = 1/4 tcyc – 29 ns
PWASH
221
—
96
—
63
—
ns
28
Delay time, AS to E rise, tASED = 1/8 tcyc – 9.5 ns(2)b
tASED
115.5
—
53
—
31
—
ns
time(2)a
29
MPU address access
tACCA = tcyc – (PWEL– tAVM) – tDSR – tf
tACCA
744.5
—
307
—
196
—
ns
35
MPU access time , tACCE = PWEH – tDSR
tACCE
—
442
—
192
—
111
ns
36
Muxed address delay (previous cycle MPU read)
tMAD = tASD + 30 ns(2)a(3)
tMAD
145.5
—
83
—
51
—
ns
1. VDD = 5.0 Vdc ± 10%, VSS = 0 Vdc, TA = TL to TH. All timing is shown with respect to 20% VDD and 70% VDD, unless
otherwise noted.
2. Input clocks with duty cycles other than 50% affect bus performance. Timing parameters affected by input clock duty cycle
are identified by (a) and (b). To recalculate the approximate bus timing values, substitute the following expressions in place
of 1/8 tCYC in the above formulas, where applicable:
(a) (1-dc) × 1/4 tCYC
(b) dc × 1/4 tCYC
Where:
DC is the decimal value of duty cycle percentage (high time).
3. Formula only for dc to 2 MHz.
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
115
Electrical Characteristics
1
2
3
E
4
4
12
9
R/W, ADDRESS
(NON-MUX)
22
36
35
17
29
18
ADDRESS
READ
DATA
ADDRESS/DATA
(MULTIPLEXED)
19
ADDRESS
WRITE
21
DATA
25
24
4
4
AS
26
27
28
Note: Measurement points shown are 20% and 70% of VDD.
Figure 9-10. Multiplexed Expansion Bus Timing Diagram
MC68HC711D3 Data Sheet, Rev. 2.1
116
Freescale Semiconductor
Serial Peripheral Interface Timing
9.9 Serial Peripheral Interface Timing
Characteristic(1)
Num
Symbol
2.0 MHz
Min Max
3.0 MHz
Min Max
Unit
Operating frequency
Master
Slave
fop(m)
fop(s)
dc
dc
0.5
2.0
dc
dc
0.5
3.0
fop
MHz
1
Cycle time
Master
Slave
tcyc(m)
tCYC(s)
2.0
500
—
—
2.0
333
—
—
tcyc
ns
2
Enable lead time
Master(2)
Slave
tlead(m)
tlead(s)
—
250
—
—
—
240
—
—
ns
3
Enable lag time
Master(2)
Slave
tlag(m)
tlag(s)
—
250
—
—
—
240
—
—
ns
4
Clock (SCK) high time
Master
Slave
tw(SCKH)m
tw(SCKH)s
340
190
—
—
227
127
—
—
ns
5
Clock (SCK) low time
Master
Slave
tw(SCKL)m
tw(SCKL)s
340
190
—
—
227
127
—
—
ns
6
Data setup time (inputs)
Master
Slave
tsu(m)
tsu(s)
100
100
—
—
100
100
—
—
ns
7
Data hold time (inputs)
Master
Slave
th(m)
th(s)
100
100
—
—
100
100
—
—
ns
8
Access time (time to data active from high-impedance state)
Slave
ta
0
120
0
120
ns
9
Disable time (hold time to high-impedance state)
Slave
tdis
—
240
—
167
ns
10
Data valid (after enable edge)(3)
tv(s)
—
240
—
167
ns
11
Data hold time (outputs) (after enable edge)
tho
0
—
0
—
ns
12
Rise time (20% VDD to 70% VDD, CL = 200 pF)
SPI outputs (SCK, MOSI, and MISO)
SPI inputs (SCK, MOSI, MISO, and SS)
trm
trs
—
—
100
2.0
—
—
100
2.0
ns
µs
13
Fall time (70% VDD to 20% VDD, CL = 200 pF)
SPI outputs (SCK, MOSI, and MISO)
SPI inputs (SCK, MOSI, MISO, and SS)
tfm
tfs
—
—
100
2.0
—
—
100
2.0
ns
µs
1. VDD = 5.0 Vdc ± 10%, VSS = 0 Vdc, TA = TL to TH. All timing is shown with respect to 20% VDD and 70% VDD, unless
otherwise noted.
2. Signal production depends on software.
3. Assumes 200 pF load on all SPI pins.
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
117
Electrical Characteristics
SS
(INPUT)
SS IS HELD HIGH ON MASTER
1
12
13
13
12
5
SCK (CPOL = 0)
(OUTPUT)
SEE
NOTE
SCK (CPOL = 1)
(OUTPUT)
SEE
NOTE
4
5
4
MISO
(INPUT)
MSB IN
BIT 6 - - - -1
LSB IN
11
10 (REF)
MOSI
(OUTPUT)
MASTER MSB OUT
11 (REF)
10
BIT 6 - - - -1
MASTER LSB OUT
13
12
Note: This first clock edge is generated internally but is not seen at the SCK pin.
Figure 9-11. SPI Master Timing (CPHA = 0)
SS
(INPUT)
SS IS HELD HIGH ON MASTER
1
13
12
5
SEE
NOTE
SCK (CPOL = 0)
(OUTPUT)
4
13
5
SEE
NOTE
SCK (CPOL = 1)
(OUTPUT)
4
MISO
(INPUT)
MSB IN
10 (REF)
MOSI
(OUTPUT)
12
BIT 6 - - - -1
LSB IN
10
11
MASTER MSB OUT
7
6
BIT 6 - - - -1
13
11 (REF)
MASTER LSB OUT
12
Note: This last clock edge is generated internally but is not seen at the SCK pin.
Figure 9-12. SPI Master Timing (CPHA = 1)
MC68HC711D3 Data Sheet, Rev. 2.1
118
Freescale Semiconductor
Serial Peripheral Interface Timing
SS
(INPUT)
1
13
12
12
13
3
5
SCK (CPOL = 0)
(INPUT)
4
2
5
SCK (CPOL = 1)
(INPUT)
4
8
MISO
(OUTPUT)
6
MOSI
(INPUT)
BIT 6 - - - -1
MSB OUT
SLAVE
7
10
SEE
NOTE
SLAVE LSB OUT
11
11
BIT 6 - - - -1
MSB IN
9
LSB IN
Note: Not defined but normally MSB of character just received
Figure 9-13. SPI Slave Timing (CPHA = 0)
SS
(INPUT)
1
12
13
5
SCK (CPOL = 0)
(INPUT)
4
2
3
5
SCK (CPOL = 1)
(INPUT)
8
MISO
(OUTPUT)
4
10
SEE
NOTE
SLAVE
MSB OUT
6
MOSI
(INPUT)
7
MSB IN
13
BIT 6 - - - -1
10
12
9
SLAVE LSB OUT
11
BIT 6 - - - -1
LSB IN
Note: Not defined but normally LSB of character previously transmitted
Figure 9-14. SPI Slave Timing (CPHA = 1)
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
119
Electrical Characteristics
MC68HC711D3 Data Sheet, Rev. 2.1
120
Freescale Semiconductor
Chapter 10
Ordering Information and Mechanical Specifications
10.1 Introduction
This section provides ordering information for the MC68HC711D3. In addition, mechanical specifications
are provided for the following packaging options:
• 40-pin plastic dual in-line package (DIP)
• 44-pin plastic leaded chip carrier (PLCC)
• 44-pin plastic quad flat pack (QFP)
10.2 Ordering Information
Table 10-1. MC Order Numbers
MC Order Number
Package Type
Temperature
2 MHz
40-pin DIP
3 MHz
–40 to +85°C
MC68HC711D3CP2
MC68HC711D3CP3
–40 to +85°C
MC68HC711D3CFN2
MC68HC711D3CFN3
–40 to +105°C
MC68HC711D3VFN2
MC68HC711D3VFN3
–40 to +85°C
MC68HC711D3CFB2
MC68HC711D3CFB3
44-pin PLCC
44-pin QFP
10.3 40-Pin DIP (Case 711-03)
40
NOTES:
1. POSITIONAL TOLERANCE OF LEADS (D),
SHALL BE WITHIN 0.25 (0.010) AT MAXIMUM
MATERIAL CONDITION, IN RELATION TO
SEATING PLANE AND EACH OTHER.
2. DIMENSION L TO CENTER OF LEADS WHEN
FORMED PARALLEL.
3. DIMENSION B DOES NOT INCLUDE MOLD
FLASH.
21
B
1
20
L
A
C
N
J
H
G
F
D
K
SEATING
PLANE
M
DIM
A
B
C
D
F
G
H
J
K
L
M
N
MILLIMETERS
MIN
MAX
51.69
52.45
13.72
14.22
3.94
5.08
0.36
0.56
1.02
1.52
2.54 BSC
1.65
2.16
0.20
0.38
2.92
3.43
15.24 BSC
0°
15°
0.51
1.02
INCHES
MIN
MAX
2.035
2.065
0.540
0.560
0.155
0.200
0.014
0.022
0.040
0.060
0.100 BSC
0.065
0.085
0.008
0.015
0.115
0.135
0.600 BSC
0°
15°
0.020
0.040
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
121
Ordering Information and Mechanical Specifications
10.4 44-Pin PLCC (Case 777-02)
-N-
Y BRK
0.007(0.180) M T
B
D
L-M S
0.007(0.180) M T
U
N S
L-M S
N S
Z
-M-
-L-
V
44
W
1
G1
X
D
0.010 (0.25) S T
VIEW D-D
A
0.007(0.180) M T
L-M S
N S
R
0.007(0.180) M T
L-M S
N S
0.007(0.180) M T
H
L-M S
L-M S
N S
N S
Z
J
K1
E
C
0.004 (0.10)
G
-TG1
0.010 (0.25) S T
L-M S
N S
K
SEATING
PLANE
F
VIEW S
0.007(0.180) M T
L-M S
N S
VIEW S
NOTES:
1. DATUMS -L-, -M-, AND -N- ARE DETERMINED
WHERE TOP OF LEAD SHOLDERS EXITS
PLASTIC BODY AT MOLD PARTING LINE.
2. DIMENSION G1, TRUE POSITION TO BE
MEASURED AT DATUM -T-, SEATING PLANE.
3. DIMENSION R AND U DO NOT INCLUDE MOLD
FLASH. ALLOWABLE MOLD FLASH IS 0.010
(0.25) PER SIDE.
4. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
5. CONTROLLING DIMENSION: INCH.
6. THE PACKAGE TOP MAY BE SMALLER THAN
THE PACKAGE BOTTOM BY UP TO 0.012
(0.300). DIMENSIONS R AND U ARE DETERMINED
AT THE OUTERMOST EXTREMES OF THE
PLASTIC BODY EXCLUSIVE OF THE MOLD
FLASH, TIE BAR BURRS, GATE BURRS AND
INTERLEAD FLASH, BUT INCLUDING ANY
MISMATCH BETWEEN THE TOP AND BOTTOM
OF THE PLASTIC BODY.
7. DIMINSION H DOES NOT INCLUDE DAMBAR
PROTRUSION OR INTRUSION. THE DAMBAR
PROTUSION(S) SHALL NOT CAUSE THE H
DIMINSION TO BE GREATER THAN 0.037
(0.940124). THE DAMBAR INTRUSION(S) SHALL
NOT CAUSE THE H DIMINISION TO SMALLER
THAN 0.025 (0.635).
INCHES
DIM
A
B
C
E
F
G
H
J
K
R
U
V
W
X
Y
Z
G1
K1
MIN
MAX
0.685
0.695
0.685
0.695
0.165
0.180
0.090
0.110
0.013
0.019
0.050 BSC
0.026
0.032
0.020
0.025
0.650
0.656
0.650
0.656
0.042
0.048
0.042
0.048
0.042
0.056
0.020
2°
10°
0.610
0.630
0.040
MILLIMETERS
MIN
MAX
17.40
17.65
17.40
17.65
4.20
4.57
2.29
2.79
0.33
0.48
1.27 BSC
0.66
0.81
0.51
0.64
16.51
16.66
16.51
16.66
1.07
1.21
1.07
1.21
1.07
1.42
0.50
2°
10°
15.50
16.00
1.02
MC68HC711D3 Data Sheet, Rev. 2.1
122
Freescale Semiconductor
44-Pin QFP (Case 824A-01)
10.5 44-Pin QFP (Case 824A-01)
B
L
B
33
23
22
S
D
V
S
0.20 (0.008)
DETAIL A
DETAIL A
F
BASE METAL
M
H A-B
S
S
C A-B
0.20 (0.008)
B
L
-B-
M
-A-
D
-A-, -B-, -D-
0.05 (0.002) A-B
34
J
N
D
44
0.20 (0.008)
12
1
11
A
M
C A-B
S
D
S
S
D
S
0.05 (0.002) A-B
S
0.20 (0.008)
M
H A-B
M
DETAIL C
C E
-H-
-CSEATING
PLANE
DATUM
PLANE
0.01 (0.004)
H
G
M
M
T
DATUM
PLANE -H-
R
K
W
C A-B
S
D
S
SECTION B-B
-D0.20 (0.008)
M
Q
X
DETAIL C
NOTES:
1. 1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. 2. CONTROLLING DIMENSION: MILLIMETER.
3. 3. DATUM PLANE -H- IS LOCATED AT BOTTOM OF
LEAD AND IS COINCIDENT WITH THE LEAD WHERE
THE LEAD EXITS THE PLASTIC BODY AT THE
BOTTOM OF THE PARTING LINE.
4. 4. DATUMS -A-, -B- AND -D- TO BE DETERMINED AT
DATUM PLANE -H-.
5. 5. DIMENSIONS S AND V TO BE DETERMINED AT
SEATING PLANE -C-.
6. 6. DIMENSIONS A AND B DO NOT INCLUDE MOLD
PROTRUSION. ALLOWABLE PROTRUSION IS 0.25
(0.010) PER SIDE. DIMENSIONS A AND B DO
INCLUDE MOLD MISMATCH AND ARE DETERMINED
AT DATUM PLANE -H-.
7. 7. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR PROTRUSION
SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE D
DIMENSION AT MAXIMUM MATERIAL CONDITION.
DAMBAR CANNOT BE LOCATED ON THE LOWER
RADIUS OR THE FOOT.
MILLIMETERS
DIM MIN
MAX
A
9.90 10.10
B
9.90 10.10
C
2.10
2.45
D
0.30
0.45
E
2.00
2.10
F
0.30
0.40
G
0.80 BSC
H
--0.25
J
0.13
0.23
K
0.65
0.95
L
8.00 REF
M
5°
10 °
N
0.13
0.17
Q
0°
7°
R
0.13
0.30
S 12.95 13.45
T
0.13
--U
0°
--V 12.95 13.45
W
0.40
--X
1.6 REF
INCHES
MIN MAX
0.390 0.398
0.390 0.398
0.083 0.096
0.012 0.018
0.079 0.083
0.012 0.016
0.031 BSC
--- 0.010
0.005 0.009
0.026 0.037
0.315 REF
5°
10 °
0.005 0.007
0°
7°
0.005 0.012
0.510 0.530
0.005
--0°
--0.510 0.530
0.016
--0.063 REF
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
123
Ordering Information and Mechanical Specifications
MC68HC711D3 Data Sheet, Rev. 2.1
124
Freescale Semiconductor
Appendix A
MC68HC11D3 and MC68HC11D0
A.1 Introduction
The MC68HC11D3 and MC68HC11D0 are read-only memory (ROM) based high-performance
microcontrollers (MCU) based on the MC68HC11E9 design. Members of the Dx series are derived from
the same mask and feature a high-speed multiplexed bus capable of running at up to 3 MHz and a fully
static design that allows operations at frequencies to dc. The only difference between the MCUs in the Dx
series is whether the ROM has been tested and guaranteed.
The information contained in this document applies to both the MC68HC11D3 and MC68HC11D0 with
the differences given in this appendix.
Features of the MC68HC11D3 and MC68HC11D0 include:
• 4 Kbytes of on-chip ROM (MC68HC11D3)
• 0 bytes of on-chip ROM (MC68HC11D0)
• 192 bytes of on-chip random-access memory (RAM) all saved during standby
• 16-bit timer system:
– Three input capture (IC) channels
– Four output compare (OC) channels
– One IC or OC software-selectable channel
• 32 input/output (I/O) pins:
– 26 bidirectional I/O pins
– 3 input-only pins
– 3 output-only pins
• Available in these packages:
– 44-pin plastic leaded chip carrier (PLCC)
– 44-pin quad flat pack (QFP)
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
125
MC68HC11D3 and MC68HC11D0
A.2 Block Diagram
MODA/LIR
MODB/VSTBY
RESET
IRQ
XIRQ
XTAL EXTAL
E
OSCILLATOR
MODE CONTROL
COP
PAI/OC1 PULSE ACCUMULATOR
OC2/OC1
OC3/OC1
OC4/OC1
TIMER
IC4/OC5/OC1
IC1
IC2
IC3
PERIODIC INTERRUPT
PORT A
MC68HC11D3 — 4 KBYTES ROM
MC68HC11D0 — 0 BYTES ROM
192 BYTES RAM
SERIAL
PERIPHERAL
INTERFACE
(SPI)
EVSS
MOSI
MISO
MC68HC11D3
CPU CORE
VSS
SERIAL
COMMUNICATIONS
INTERFACE
(SCI)
SCK
VDD
SS
PA7
PA6
PA5
PA4
PA3
PA2
PA1
PA0
CLOCK LOGIC
INTERRUPT CONTROL
TxD
RxD
A0/D0
A1/D1
A2/D2
A3/D3
A4/D4
A5/D5
A6/D6
A7/D7
A8
A9
A10
A11
A12
A13
A14
A15
MULTIPLEXED ADDRESS/DATA BUS
PD0
PD1
PD2
PORT D
PD3
PORT C
PD4
PORT B
PD5
DATA DIRECTION REGISTER D
PD6/AS
DATA DIRECTION REGISTER C
PD7/R/W
DATA DIRECTION REGISTER B
Figure A-1. MC68HC11D3 Block Diagram
MC68HC711D3 Data Sheet, Rev. 2.1
126
Freescale Semiconductor
Pin Assignments
EXTAL
E
MODA/LIR
MODB/VSTBY
42
41
40
VSS
2
43
PC0
3
XTAL
PC1
4
EVSS
PC2
5
44
PC3
6
A.3 Pin Assignments
39
PB0/A8
7
PC5/A5/D5
8
38
PB1/A9
PC6/A6/D6
9
37
PB2/A10
PC7/A7/D7
10
36
PB3/A11
1
PC4/A4/D4
26
27
28
PA4/OC4
PA3/IC4/OC5/OC1
PA2/IC1
PA1/IC2
25
PA0/IC3
29
PA5/OC3
30
17
24
16
PD1/TxD
PA6/OC2
PD0/RxD
23
NC
22
IRQ
31
VDD
PB7
15
PA7/PAI
PB6/A14
32
21
33
14
PD5/SS
13
RESET
20
PD6/AS
19
PB5/A13
PD4/SCK
PB4/A12
34
PD3/MOSI
35
12
18
11
PD2/MISO
XIRQ
PD7/R/W
MODB
38
34
XTAL
39
MODA
VSS
40
35
EVSS
41
E
PC0
42
36
PC1
1
PC5
2
PC6
3
31
PB2
37
PC2
PB1
PC4
43
PB0
32
PC3
EXTAL
Figure A-2. Pin Assignments for 44-Pin PLCC
PD6
7
27
PB6
RESET
8
26
PB7
IRQ
9
25
NC
PD0
10
24
PA0
15
16
17
18
19
20
21
23
PA1
VDD
PA7
PA6
PA5
PA4
PA3
PA2
PB5
PD5
28
14
PD7
PD4
PB4
6
13
PB3
29
PD3
30
5
12
4
PD2
PC7
XIRQ
PD1
Figure A-3. Pin Assignments for 44-Pin QFP
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
127
MC68HC11D3 and MC68HC11D0
A.4 Memory Map
$0000
$0000 INTERNAL REGISTERS AND I/O
(CAN BE MAPPED TO ANY 4-K BOUNDARY
$003F USING INIT REGISTER)
$0040 192 BYTES STATIC RAM
(CAN BE MAPPED TO ANY 4-K BOUNDARY
$00FF USING THE INIT REGISTER)
$7000 4 KBYTES ROM (MC68HC11D3)
PRESENT AT RESET AND CAN BE DISABLED BY
$7FFF ROM ON BIT IN CONFIG REGISTER.
INTERRUPT VECTORS ARE EXTERNAL.
$7000
$8000
EXTERNAL
EXTERNAL
$B000
$BF00
BOOT
ROM
$BFFF
$FF00
4-KBYTES
ROM
$FFFF
SINGLE
CHIP
EXPANDED
SPECIAL
MULTIPLEXED BOOTSTRAP
SPECIAL
TEST
$FFFF
$BFC0
SPECIAL MODES
INTERRUPT
$BFFF VECTORS
$FFC0
NORMAL MODES
INTERRUPT
$FFFF VECTORS
Figure A-4. MC68HC11Dx(1) Memory Map
A.5 MC68HC11D3 and MC68HC11D0 Electrical Characteristics
The parameters given in Chapter 9 Electrical Characteristics apply to the MC68HC11D3 and
MC68HC11D0 with the exceptions given here.
A.5.1 Functional Operating Temperature Range
Rating
Operating temperature range
MC68HC11D0C
Symbol
Value
Unit
TA
TL to TH
–40 to +85
°C
Symbol
Value
Unit
ΘJA
50
85
°C/W
A.5.2 Thermal Characteristics
Characteristic
Package thermal resistance (junction-to-ambient)
44-pin plastic leaded chip carrier (PLCC)
44-pin plastic quad flat pack (QFP
1. MC68HC11D0 only operates in expanded multiplexed mode and bootstrap mode.
MC68HC711D3 Data Sheet, Rev. 2.1
128
Freescale Semiconductor
Ordering Information
A.6 Ordering Information
MC Order Number
MCU
MC68HC11D3
(Custom ROM)
MC68HC11D0
(No ROM)
Package
Temperature
2 MHz
3 MHz
44-pin PLCC
–40 to +85°C
MC68HC11D3CFN2
MC68HC11D3CFN3
44-pin PLCC
–40 to +85°C
MC68HC11D0CFN2
MC68HC11D0CFN3
44-pin QFP
–40 to +85°C
MC68HC11D0CFB2
MC68HC11D0CFB3
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
129
MC68HC11D3 and MC68HC11D0
MC68HC711D3 Data Sheet, Rev. 2.1
130
Freescale Semiconductor
Appendix B
MC68L11D0
B.1 Introduction
The MC68L11D0 is an extended-voltage version of the MC68HC11D0 microcontroller that can operate
in applications that require supply voltages as low as 3.0 volts. Operation is identical to that of the
MC68HC11D0 (see Appendix A MC68HC11D3 and MC68HC11D0) in all aspects other than electrical
parameters, as shown in this appendix.
Features of the MC68HC11D0 include:
• Suitable for battery-powered portable and hand-held applications
• Excellent for use in devices such as remote sensors and actuators
• Operating performance is same at 5 V and 3 V
B.2 MC68L11D0 Electrical Characteristics
The parameters given in Chapter 9 Electrical Characteristics apply to the MC68L11D0 with the exceptions
given here.
B.2.1 Functional Operating Temperature Range
Rating
Operating temperature range
Symbol
Value
Unit
TA
TL to TH
–20 to +70
°C
B.2.2 DC Electrical Characteristics
Characteristic(1)
Symbol
Min
Max
Unit
Output voltage(2) All outputs except XTAL
ILoad = ± 10.0 µAAll outputs except XTAL, RESET, and MODA
VOL
VOH
—
VDD – 0.1
0.1
—
V
Output high voltage(1) All outputs except XTAL, RESET, and MODA
ILoad = – 0.5 mA, VDD = 3.0 V
ILoad = – 0.8 mA, VDD = 4.5 V
VOH
VDD – 0.8
—
V
Output low voltage All outputs except XTAL
ILoad = 1.6 mA, VDD = 5.0 V
ILoad = 1.0 mA, VDD = 3.0 V
VOL
—
0.4
V
The dc electrical table continues on next page.
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
131
MC68L11D0
Characteristic(1)
Symbol
Min
Max
Unit
Input high voltage All inputs except RESET
RESET
VIH
0.7 x VDD
0.8 x VDD
VDD + 0.3
VDD + 0.3
V
Input low voltage All inputs
VIL
VSS – 0.3
0.2 x VDD
V
I/O ports, three-state leakage PA7, PA3, PC7–PC0,
VIn = VIH or VIL PD7–PD0, MODA/LIR, RESET
IOZ
—
±10
µA
Input leakage current
VIn = VDD or VSS PA2–PA0, IRQ, XIRQ
VIn = VDD or VSS MODB/VSTBY
IIn
—
—
±1
±10
µA
RAM standby voltagePower down
VSB
2.0
VDD
V
RAM standby currentPower down
ISB
—
10
µA
Input capacitancePA2–PA0, IRQ, XIRQ, EXTAL
PA3, PA7, PC7–PC0, PD7–PD0, MODA/LIR, RESET
CIn
—
—
8
12
pF
Output load capacitanceAll outputs except PD4–PD1
PD4–PD1
CL
—
—
90
100
pF
Total supply current(3)
RUN:
Single-chip mode
VDD = 5.5 V
VDD = 3.0 V
Expanded multiplexed mode
VDD = 5.5 V
VDD = 3.0 V
WAIT — All peripheral functions shut down:
Single-chip mode
VDD = 5.5 V
VDD = 3.0 V
Expanded multiplexed mode
VDD = 5.5 V
VDD = 3.0 V
STOP — No clocks, single-chip mode:
VDD = 5.5 V
VDD = 3.0 V
Power dissipation
Single-chip mode
VDD = 5.5 V
VDD = 3.0 V
Expanded multiplexed mode
VDD = 5.5 V
VDD = 3.0 V
IDD
mA
8
4
15
8
14
7
27
14
WIDD
SIDD
PD
mA
3
1.5
6
3
5
2.5
10
5
50
25
50
25
44
12
85
24
77
21
150
42
µA
mW
1. VDD = 3.0 Vdc to 5.5 Vdc, VSS = 0 Vdc, TA = TL to TH, unless otherwise noted.
2. VOH specification for RESET and MODA is not applicable because they are open-drain pins. VOH specification is not
applicable to ports C and D in wired-OR mode.
3. EXTAL is driven with a square wave, and
tcyc = 1000 ns for 1 MHz rating;
tcyc = 500 ns for 2 MHz rating;
VIL ≤ 0.2 V;
VIH ≥ VDD – 0.2 V;
No dc loads
MC68HC711D3 Data Sheet, Rev. 2.1
132
Freescale Semiconductor
MC68L11D0 Electrical Characteristics
B.2.3 Control Timing
Characteristic(1)
1.0 MHz
Symbol
2.0 MHz
Min
Max
Min
Max
Unit
Frequency of operation
fO
dc
1.0
dc
2.0
MHz
E-clock period
tcyc
1000
—
500
—
ns
Crystal frequency
fXTAL
—
4.0
—
8.0
MHz
External oscillator frequency
4 fO
dc
4.0
dc
8.0
MHz
Processor control setup time
tPCSU = 1/4 tcyc + 50 ns
tPCSU
325
—
200
—
ns
PWRSTL
8
1
—
—
8
1
—
—
tcyc
PWIRQ
1020
—
520
—
ns
tWRS
—
4
—
4
tcyc
PWTIM
1020
—
520
—
ns
Reset input pulse width(2)
To guarantee external reset vector
Minimum input time can be preempted by internal reset
Interrupt pulse width, PWIRQ = tcyc + 20 ns
IRQ edge-sensitive mode
Wait recovery startup time
Timer pulse width PWTIM = tcyc + 20 ns
Input capture pulse accumulator input
1. VDD = 3.0 Vdc to 5.5 Vdc, VSS = 0 Vdc, TA = TL to TH. All timing is shown with respect to 20% VDD and 70% VDD, unless
otherwise noted.
2. Reset is recognized during the first clock cycle it is held low. Internal circuitry then drives the pin low for four clock cycles,
releases the pin, and samples the pin level two cycles later to determine the source of the interrupt. Refer to Chapter 4
Resets, Interrupts, and Low-Power Modes for further details.
B.2.4 Peripheral Port Timing
Characteristic(1)
Symbol
1.0 MHz
2.0 MHz
Min
Max
Min
Max
Unit
Frequency of operation (E-clock frequency)
fO
dc
1.0
dc
2.0
MHz
E-clock period
tcyc
1000
—
500
—
ns
Peripheral data setup time(2)
MCU read of ports A, B, C, and D
tPDSU
100
—
100
—
ns
Peripheral data hold time(2)
MCU read of ports A, B, C, and D
tPDH
50
—
50
—
ns
Delay time, peripheral data write
MCU write to port A
MCU writes to ports B, C, and D
tPWD = 1/4 tcyc + 150 ns
tPWD
—
200
—
200
—
350
—
225
ns
1. VDD = 3.0 Vd to 5.5 Vdc, VSS = 0 Vdc, TA = TL to TH. All timing is shown with respect to 20% VDD and 70% VDD, unless
otherwise noted.
2. Port C and D timing is valid for active drive (CWOM and DWOM bits not set in PIOC and SPCR registers respectively).
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
133
MC68L11D0
B.2.5 Expansion Bus Timing
Characteristic(1)
Num
Symbol
Frequency of operation (E-clock frequency)
1.0 MHz
2.0 MHz
Unit
Min
Max
Min
Max
fO
dc
1.0
dc
2.0
MHz
tcyc
1000
—
500
—
ns
1
Cycle time
2
Pulse width, E low, PWEL = 1/2 tcyc — 23 ns
PWEL
475
—
225
—
ns
3
Pulse width, E high, PWEH = 1/2 tcyc – 28 ns
PWEH
470
—
220
—
ns
4A
E and AS rise time
tr
—
25
—
25
ns
4B
E and AS fall time
tf
—
25
—
25
ns
9
Address hold time(2)a, tAH = 1/8 tcyc – 29.5 ns
tAH
95
—
33
—
ns
12
Non-muxed address valid time to E rise
tAV = PWEL – (tASD + 80 ns)(2)a
tAV
275
—
88
—
ns
17
Read data setup time
tDSR
30
—
30
—
ns
18
Read data hold time (max = tMAD)
tDHR
0
150
0
88
ns
tDDW
—
195
—
133
ns
ns(2)a
19
Write data delay time, tDDW = 1/8 tcyc + 65.5
21
Write data hold time, tDHW = 1/8 tcyc – 29.5 ns(2)a
tDHW
95
—
33
—
ns
22
Muxed address valid time to E rise
tAVM = PWEL – (tASD + 90 ns)(2)a
tAVM
265
—
78
—
ns
24
Muxed address valid time to AS fall
tASL = PWASH – 70 ns
tASL
150
—
25
—
ns
25
Muxed address hold time, tAHL = 1/8 tcyc – 29.5 ns(2)b
tAHL
95
—
33
—
ns
26
Delay time, E to AS rise, tASD = 1/8 tcyc – 9.5 ns(2)a
tASD
120
—
58
—
ns
27
Pulse width, AS high, PWASH = 1/4 tcyc – 29 ns
PWASH
220
—
95
—
ns
28
Delay time, AS to E rise, tASED = 1/8 tcyc – 9.5 ns(2)b
tASED
120
—
58
—
ns
29
MPU address access time(2)a
tACCA = tcyc – (PWEL– tAVM) – tDSR – tf
tACCA
735
—
298
—
ns
35
MPU access time , tACCE = PWEH – tDSR
tACCE
—
440
—
190
ns
36
Muxed address delay (previous cycle MPU read)
tMAD = tASD + 30 ns(2)a
tMAD
150
—
88
—
ns
1. VDD = 3.0 Vdc to 5.5 Vdc, VSS = 0 Vdc, TA = TL to TH. All timing is shown with respect to 20% VDD and 70% VDD, unless
otherwise noted.
2. Input clocks with duty cycles other than 50% affect bus performance. Timing parameters affected by input clock duty cycle
are identified by (a) and (b). To recalculate the approximate bus timing values, substitute the following expressions in place
of 1/8 tCYC in the above formulas, where applicable:
(a) (1-dc) × 1/4 tCYC
(b) dc × 1/4 tCYC
Where:
DC is the decimal value of duty cycle percentage (high time).
MC68HC711D3 Data Sheet, Rev. 2.1
134
Freescale Semiconductor
MC68L11D0 Electrical Characteristics
B.2.6 Serial Peripheral Interface Timing
Characteristic(1)
Num
Symbol
1.0 MHz
Min
Max
2.0 MHz
Min
Max
Unit
Operating frequency
Master
Slave
fop(m)
fop(s)
dc
dc
0.5
1.0
dc
dc
0.5
2.0
fop
MHz
1
Cycle time
Master
Slave
tcyc(m)
tCYC(s)
2.0
1000
—
—
2.0
500
—
—
tcyc
ns
2
Enable lead time
Master(2)
Slave
tlead(m)
tlead(s)
—
500
—
—
—
250
—
—
ns
3
Enable lag time
Master(2)
Slave
tlag(m)
tlag(s)
—
500
—
—
—
250
—
—
ns
4
Clock (SCK) high time
Master
Slave
tw(SCKH)m
tw(SCKH)s
680
380
—
—
340
190
—
—
ns
5
Clock (SCK) low time
Master
Slave
tw(SCKL)m
tw(SCKL)s
680
380
—
—
340
190
—
—
ns
6
Data setup time (inputs)
Master
Slave
tsu(m)
tsu(s)
100
100
—
—
100
100
—
—
ns
7
Data hold time (inputs)
Master
Slave
th(m)
th(s)
100
100
—
—
100
100
—
—
ns
8
Access time (time to data active from high-impedance state)
Slave
ta
0
120
0
120
ns
9
Disable time (hold time to high-impedance state)
Slave
tdis
—
240
—
240
ns
10
Data valid (after enable edge)(3)
tv(s)
—
240
—
240
ns
11
Data hold time (outputs) (after enable edge)
tho
0
—
0
—
ns
12
Rise time (20% VDD to 70% VDD, CL = 200 pF)
SPI outputs (SCK, MOSI, and MISO)
SPI inputs (SCK, MOSI, MISO, and SS)
trm
trs
—
—
100
2.0
—
—
100
2.0
ns
µs
13
Fall time (70% VDD to 20% VDD, CL = 200 pF)
SPI outputs (SCK, MOSI, and MISO)
SPI inputs (SCK, MOSI, MISO, and SS)
tfm
tfs
—
—
100
2.0
—
—
100
2.0
ns
µs
1. VDD = 3.0 Vdc to 5.5 Vdc, VSS = 0 Vdc, TA = TL to TH. All timing is shown with respect to 20% VDD and 70% VDD, unless
otherwise noted.
2. Signal production depends on software.
3. Assumes 100 pF load on all SPI pins.
MC68HC711D3 Data Sheet, Rev. 2.1
Freescale Semiconductor
135
MC68L11D0
B.3 Ordering Information
Package
Frequency
Features
MC Order Number
44-pin PLCC
2 MHz
No ROM
MC68L11D0FN2
44-pin QFP
2 MHz
No ROM
MC68L11D0FB2
MC68HC711D3 Data Sheet, Rev. 2.1
136
Freescale Semiconductor
How to Reach Us:
Home Page:
www.freescale.com
RoHS-compliant and/or Pb- free versions of Freescale products have the functionality
and electrical characteristics of their non-RoHS-compliant and/or non-Pb- free
counterparts. For further information, see http://www.freescale.com or contact your
Freescale sales representative.
E-mail:
[email protected]
For information on Freescale.s Environmental Products program, go to
http://www.freescale.com/epp.
USA/Europe or Locations Not Listed:
Freescale Semiconductor
Technical Information Center, CH370
1300 N. Alma School Road
Chandler, Arizona 85224
+1-800-521-6274 or +1-480-768-2130
[email protected]
Europe, Middle East, and Africa:
Freescale Halbleiter Deutschland GmbH
Technical Information Center
Schatzbogen 7
81829 Muenchen, Germany
+44 1296 380 456 (English)
+46 8 52200080 (English)
+49 89 92103 559 (German)
+33 1 69 35 48 48 (French)
[email protected]
Japan:
Freescale Semiconductor Japan Ltd.
Headquarters
ARCO Tower 15F
1-8-1, Shimo-Meguro, Meguro-ku,
Tokyo 153-0064
Japan
0120 191014 or +81 3 5437 9125
[email protected]
Asia/Pacific:
Freescale Semiconductor Hong Kong Ltd.
Technical Information Center
2 Dai King Street
Tai Po Industrial Estate
Tai Po, N.T., Hong Kong
+800 2666 8080
[email protected]
For Literature Requests Only:
Freescale Semiconductor Literature Distribution Center
P.O. Box 5405
Denver, Colorado 80217
1-800-441-2447 or 303-675-2140
Fax: 303-675-2150
[email protected]
MC68HC711D3
Rev. 2.1, 07/2005
Information in this document is provided solely to enable system and software
implementers to use Freescale Semiconductor products. There are no express or
implied copyright licenses granted hereunder to design or fabricate any integrated
circuits or integrated circuits based on the information in this document.
Freescale Semiconductor reserves the right to make changes without further notice to
any products herein. Freescale Semiconductor makes no warranty, representation or
guarantee regarding the suitability of its products for any particular purpose, nor does
Freescale Semiconductor assume any liability arising out of the application or use of any
product or circuit, and specifically disclaims any and all liability, including without
limitation consequential or incidental damages. “Typical” parameters that may be
provided in Freescale Semiconductor data sheets and/or specifications can and do vary
in different applications and actual performance may vary over time. All operating
parameters, including “Typicals”, must be validated for each customer application by
customer’s technical experts. Freescale Semiconductor does not convey any license
under its patent rights nor the rights of others. Freescale Semiconductor products are
not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life,
or for any other application in which the failure of the Freescale Semiconductor product
could create a situation where personal injury or death may occur. Should Buyer
purchase or use Freescale Semiconductor products for any such unintended or
unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all
claims, costs, damages, and expenses, and reasonable attorney fees arising out of,
directly or indirectly, any claim of personal injury or death associated with such
unintended or unauthorized use, even if such claim alleges that Freescale
Semiconductor was negligent regarding the design or manufacture of the part.
Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc.
All other product or service names are the property of their respective owners.
© Freescale Semiconductor, Inc. 2005. All rights reserved.