MC14467-1 Rev 5.0, 3/2007 Freescale Semiconductor Technical Data Low-Power CMOS Ionization Smoke Detector IC MC14467-1 The MC14467-1, when used with an ionization chamber and a small number of external components, will detect smoke. When smoke is sensed, an alarm is sounded via an external piezoelectric transducer and internal drivers. This circuit is designed to operate in smoke detector systems that comply with UL217 and UL268 specifications. LOW-POWER CMOS IONIZATION SMOKE DETECTOR IC Features • • • • • • • • • • Ionization Type with On-Chip FET Input Comparator Piezoelectric Horn Driver Guard Outputs on Both Sides of Detect Input Input-Production Diodes on the Detect Input Low-Battery Trip Point, Internally Set, can be Altered Via External Resistor Detect Threshold, Internally Set, can be Altered Via External Resistor Pulse Testing for Low Battery Uses LED for Battery Loading Comparator Outputs for Detect and Low Battery Internal Reverse Battery Protection Pb-Free Packaging Designated by Suffix Code ED and EG P SUFFIX ED SUFFIX (PB-FREE) 16-LEAD PLASTIC DIP CASE 648-08 EG SUFFIX (PB-FREE) 16-LEAD SOICW CASE 751G-04 ORDERING INFORMATION Device Case No. Package 648-08 Plastic Dip 751G-04 SOICW DETECT COMP. OUT 1 16 GUARD HI-Z N/C 2 15 DETECT INPUT LOW V SET 3 14 GUARD LO-Z LOW V COMP. OUT 4 13 SENSITIVITY SET MC14467P1 MC14467ED1 MCZ14467EG/R2 LED 5 12 OSC CAPACITOR VDD 6 11 SILVER TIMING RESISTOR 7 10 BRASS FEEDBACK 8 9 VSS DETECT COMP. OUT 1 16 GUARD HI-Z N/C 2 15 DETECT INPUT LOW V SET 3 14 GUARD LO-Z LOW V COMP. OUT 4 13 LED 5 12 VDD 6 11 SENSITIVITY SET OSC CAPACITOR SILVER TIMING RESISTOR 7 10 BRASS FEEDBACK 8 9 VSS Figure 1. Pin Connections © Freescale Semiconductor, Inc., 2007. All rights reserved. VDD Priezoelectric Horn Driver 8 VDD 4 80 K Low Battery Comp. – 3 11 Latch 10 + 7 VDD 1045 K Oscillator Timer 12 VDD 5 13 + Latch – 15 1125 K 6 9 Led Driver 1 Detect Input 14 Lo-Z VDD + – Active Guard Figure 2. Block Diagram Table 1. Maximum Ratings(1) (Voltages referenced to VSS) Rating Symbol Value Unit DC Supply Voltage VDD −0.5 to + 15 V Input Voltage, All Inputs Except Pin 8 VIN −0.25 to VDD + 0.25 V DC Current Drain per Input Pin, Except Pin 15 = 1 mA I 10 mA DC Current Drain per Output Pin I 30 mA Operating Temperature Range Storage Temperature Range Reverse Battery Time TA −10 to +60 °C TSTG −55 to + 125 °C tRB 5.0 s 1. Maximum Ratings are those values beyond which damage to the device may occur. This device contains circuitry to protect the inputs against damage due to high static voltages or electric fields; however, it is advised that normal precautions be taken to avoid application of any voltage higher than maximum rated voltages to this high impedance circuit. For proper operation it is recommended that except for pin 8, VIN and VOUT be constrained to the range VSS ≤ (VIN or VOUT ) VDD. For pin 8, refer to the Electrical Characteristics. MC14467-1 2 Sensors Freescale Semiconductor Table 2. Recommended Operating Conditions (Voltages referenced to VSS) Parameter Symbol Value Unit VDD 9.0 V Timing Capacitor — 0.1 µF Timing Resistor — 8.2 MΩ Battery Load (Resistor or LED) — 10 mA Supply Voltage Table 3. Electrical Characteristics (Voltages referenced to VSS, TA = 25°C) Symbol VDD VDC Min Typ(1) Max Unit Operating Voltage VDD — 6.0 — 12 V Output Voltage Piezoelectric Horn Drivers (IOH = -16 mA) Comparators (IOH = -30 µA) Piezoelectric Horn Drivers (IOL = +16 mA) Comparators (IOL = +30 µA) VOH 7.2 9.0 7.2 9.0 6.3 8.5 — — — 8.8 — 0.1 — — 0.9 0.5 Output Voltage - LED Driver, IOL = 10 mA VOL 7.2 — — 3.0 Output Impedance, Active Guard Pin 14 Pin 16 LO-Z HI-Z 9.0 9.0 — — — — 10 1000 Operating Current (Rbias = 8.2 MΩ) IDD 9.0 12.0 — — 5.0 — 9.0 12.0 µA Input Current - Detect (40% R.H.) IIN 9.0 — — ± 1.0 pA Internal Set Voltage Low Battery Sensitivity VLOW VSET 9.0 — 7.2 47 — 50 7.8 53 V %VDD Hysteresis VHYS 9.0 75 100 150 mV Offset Voltage (measured at Vin = VDD/2 Active Guard Detect Comparator VOS 9.0 9.0 — — — — ± 100 ± 50 Input Voltage Range, Pin 8 VIN — VSS - 10 — VDD + 10 V Input Capacitance CIN — — 5.0 — pF Common Mode Voltage Range, Pin 15 VCM — 0.6 — VDD - 2 V Characteristic VOL V V V kΩ mV 1. Data labelled “Typ'' is not to be used for design purposes but is intended as an indication of the IC's potential performance. MC14467-1 Sensors Freescale Semiconductor 3 Table 4. Timing Parameters (C = 0.1 µF, Rbias = 8.2 MΩ, VDD = 9.0 V, TA = 25°C, See Figure 7) Symbol Min Typ(1) Max Units tCI 1.34 32 1.67 40 2.0 48 s ms tR 8.0 10 12 ms On Time Off Time PWON PWOFF 120 60 160 80 208 104 ms ms LED Output Between Pulses On Time tLED PWON 32 8.0 40 10 48 12 s ms Horn Output (During Low Battery) On Time Between Pulses tON tOFF 8.0 32 10 40 12 48 ms s Characteristics Oscillator Period No Smoke Smoke Oscillator Rise Time Horn Output (During Smoke) 1. Data labelled “Typ” is not to be used for design purposes but is intended as an indication of the IC’s potential performance. 100.0 10.0 TA = 25°C VDD = 9.0 VDC TA = 25°C ID , Drain Current (mA) ID , Drain Current (mA) 10.0 VDD = 7.2 VDC 1.0 0.1 0 1 2 3 4 5 6 7 8 9 1.0 VDD = 9.0 VDC or 7.2 VDC 0.1 P-CH Source And N-CH Sink Current 0.01 10 0 VDS, Drain To Source Voltage (VDC) 1 2 3 4 5 6 7 1000.0 TA = 25°C VDD = 9.0 VDC VDD = 9.0 VDC 100.0 ID, Drain Current (mA) ID, Drain Current (mA) 10 1000.0 TA = 25°C VDD = 7.2 VDC 10.0 VDD = 7.2 VDC 10.0 P-CH Source Current 1.0 0 9 Figure 4. Typical Comparator Output I-V Characteristic Figure 3. Typical LED Output I-V Characteristic 100.0 8 VDS, Drain To Source Voltage (VDC) 1 2 3 4 5 6 7 VDS, Drain To Source Voltage (VDC) N-CH Sink Current 8 9 10 1.0 0 1 2 3 4 5 6 7 8 9 10 VDS, Drain To Source Voltage (VDC) Figure 5. Typical P Horn Driver Output I-V Characteristic MC14467-1 4 Sensors Freescale Semiconductor DEVICE OPERATION Timing The internal oscillator of the MC14467-1 operates with a period of 1.67 seconds during no-smoke conditions. Each 1.67 seconds, internal power is applied to the entire IC and a check is made for smoke, except during LED pulse, Low Battery Alarm Chirp, or Horn Modulation (in smoke). Every 24 clock cycles a check is made for low battery by comparing VDD to an internal zener voltage. Since very small currents are used in the oscillator, the oscillator capacitor should be of a low leakage type. Detect Circuitry If smoke is detected, the oscillator period becomes 40 ms and the piezoelectric horn oscillator circuit is enabled. The horn output is modulated 160 ms on, 80 ms off. During the off time, smoke is again checked and will inhibit further horn output if no smoke is sensed. During smoke conditions the low battery alarm is inhibited, but the LED pulses at a 1.0 Hz rate. An active guard is provided on both pins adjacent to the detect input. The voltage at these pins will be within 100 mV of the input signal. This will keep surface leakage currents to a minimum and provide a method of measuring the input voltage without loading the ionization chamber. The active guard op amp is not power strobed and thus gives constant protection from surface leakage currents. Pin 15 (the Detect input) has internal diode protection against static damage. Sensitivity/Low Battery Thresholds Both the sensitivity threshold and the low battery voltage levels are set internally by a common voltage divider (please see Figure 2) connected between VDD and VSS. These voltages can be altered by external resistors connected from pins 3 or 13 to either VDD or VSS. There will be a slight interaction here due to the common voltage divider network. The sensitivity threshold can also be set by adjusting the smoke chamber ionization source. Test Mode Since the internal op amps and comparators are power strobed, adjustments for sensitivity or low battery level could be difficult and/or time-consuming. By forcing Pin 12 to VSS, the power strobing is bypassed and the outputs, Pins 1 and 4, constantly show smoke/no smoke and good battery/low battery, respectively. Pin 1 = VDD for smoke and Pin 4 = VDD for low battery. In this mode and during the 10 ms power strobe, chip current rises to approximately 50 µA. LED Pulse The 9-volt battery level is checked every 40 seconds during the LED pulse. The battery is loaded via a 10 mA pulse for 10 ms. If the LED is not used, it should be replaced with an equivalent resistor such that the battery loading remains at 10 mA. Hysteresis When smoke is detected, the resistor/divider network that sets sensitivity is altered to increase sensitivity. This yields approximately 100 mV of hysteresis and reduces false triggering. 1M 1M Test 1 330 Ω 8.2 MΩ 0.1 µF MC14467-1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 0.1 µF + 9.0 V 1.5 MΩ* 0.001* µF 220 kΩ* *NOTE: Component values may change depending on type of piezoelectric horn used. Figure 6. Typical Application as Ionization Smoke Detector MC14467-1 Sensors Freescale Semiconductor 5 Standby No Smoke/ No Low Battery Smoke/no Low Battery Smoke/Low Battery 10 m s 40 m s OSCILLATOR (Pin 12) No Smoke/low Battery 1.67 s DETECT OUT (Pin 1) LOW BATTERY OUT (Pin 4) HYSTERESIS (Internal) (Pins 13 & 14) SAMPLE (Internal) Smoke HORN (Pins 10 & 11) (Note 1) Battery Test LED (Pin 5) Suppressed Chirp (Note 3) 24 Clock Cycles 24 Clock Cycles (0.96 s) (Note 3) 24 Clock Cycles 6 Clock Cycles (10.0 s) (40 s) Notes: 1. Horn modulation is self-completing. When going from smoke to no smoke, the alarm condition will terminate only when horn is off. 2. Comparators are strobed on once per clock cycle (1.67 s for no smoke, 40 ms for smoke). 3. Low battery comparator information is latched only during LED pulse. 4. ~ 100 mVp–p swing. Figure 7. Timing Diagram MC14467-1 6 Sensors Freescale Semiconductor PACKAGE DIMENSIONS CASE 648-08 ISSUE T 16-LEAD PLASTIC DIP MC14467-1 Sensors Freescale Semiconductor 7 PACKAGE DIMENSIONS CASE 751G-04 ISSUE F 16-LEAD SOICW MC14467-1 8 Sensors Freescale Semiconductor How to Reach Us: Home Page: www.freescale.com Web Support: http://www.freescale.com/support USA/Europe or Locations Not Listed: Freescale Semiconductor, Inc. Technical Information Center, EL516 2100 East Elliot Road Tempe, Arizona 85284 +1-800-521-6274 or +1-480-768-2130 www.freescale.com/support Europe, Middle East, and Africa: Freescale Halbleiter Deutschland GmbH Technical Information Center Schatzbogen 7 81829 Muenchen, Germany +44 1296 380 456 (English) +46 8 52200080 (English) +49 89 92103 559 (German) +33 1 69 35 48 48 (French) www.freescale.com/support Japan: Freescale Semiconductor Japan Ltd. Headquarters ARCO Tower 15F 1-8-1, Shimo-Meguro, Meguro-ku, Tokyo 153-0064 Japan 0120 191014 or +81 3 5437 9125 [email protected] Asia/Pacific: Freescale Semiconductor Hong Kong Ltd. Technical Information Center 2 Dai King Street Tai Po Industrial Estate Tai Po, N.T., Hong Kong +800 2666 8080 [email protected] For Literature Requests Only: Freescale Semiconductor Literature Distribution Center P.O. Box 5405 Denver, Colorado 80217 1-800-441-2447 or 303-675-2140 Fax: 303-675-2150 [email protected] MC14467-1 Rev. 5.0 3/2007 RoHS-compliant and/or Pb-free versions of Freescale products have the functionality and electrical characteristics of their non-RoHS-compliant and/or non-Pb-free counterparts. For further information, see http://www.freescale.com or contact your Freescale sales representative. For information on Freescale’s Environmental Products program, go to http:// www.freescale.com/epp. Information in this document is provided solely to enable system and software implementers to use Freescale Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. Freescale Semiconductor reserves the right to make changes without further notice to any products herein. Freescale Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters that may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”, must be validated for each customer application by customer’s technical experts. Freescale Semiconductor does not convey any license under its patent rights nor the rights of others. Freescale Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale Semiconductor product could create a situation where personal injury or death may occur. Should Buyer purchase or use Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was negligent regarding the design or manufacture of the part. Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. © Freescale Semiconductor, Inc. 2007. All rights reserved.