MCC TM Micro Commercial Components ER3A-HT THRU ER3M-HT omponents 20736 Marilla Street Chatsworth !"# $ % !"# Features • • • • 3.0 Amp High Efficient Rectifiers 50 to 1000 Volts Low forward voltage drop High current capability High reliability High surge current capability Maximum Ratings • • Operating Temperature: -55℃ to +125℃ Storage Temperature: -55℃ to +150℃ MCC Part Number Device Marking ER3A-HT ER3B-HT ER3D-HT ER3G-HT ER3J-HT ER3K-HT ER3M-HT ER3A ER3B ER3D ER3G ER3J ER3K ER3M Maximum Recurrent Peak Reverse Voltage 50V 100V 200V 400V 600V 800V 1000V Maximum RMS Voltage 35V 70V 140V 280V 420V 560V 700V DO-214AB (SMCJ) (Round Lead) Maximum DC Blocking Voltage 50V 100V 200V 400V 600V 800V 1000V H Cathode Band J A E Average Forward Current Peak Forward Surge Current Maximum Instantaneous Forward Voltage ER3A-HT~ER3D-HT ER3G-HT ER3J-HT~ER3M-HT Maximum DC Reverse Current At Rated DC Blocking Voltage Maximum Reverse Recovery Time ER3A-HT~ER3G-HT ER3J-HT~ER3M-HT Typical Junction Capacitance IF(AV) IFSM VF 3.0A 150A 1.0V 1.3V 1.7V IFM = 3.0A; TA = 25℃ B G TA = 55℃ 8.3ms, half sine D F Electrical Characteristics @ 25℃ Unless Otherwise Specified C DIMENSIONS DIM A B C D E F G H J INCHES MIN .200 .177 .002 --.047 .168 .309 .239 .234 MM MIN 5.08 4.70 .05 --1.20 4.27 7.85 6.08 5.95 MAX .214 .203 .005 .02 .056 .179 .322 .243 .240 MAX 5.43 5.30 .13 .51 1.42 4.55 8.18 6.18 6.10 NOTE SUGGESTED SOLDER PAD LAYOUT IR Trr CJ 10uA 200uA 50ns 75ns TA = 25℃ TA = 100℃ IF=0.5A, IR=1.0A IRR=0.25A 0.190 0.200” Measured at 1.0MHz, VR=4.0V 0.070” 80pF 50pF *Pulse Test: Pulse Width 300µsec, Duty Cycle 1% ER3A-HT~ER3G-HT ER3J-HT~ER3M-HT www.mccsemi.com Revision: 1 2005/08/31 MCC ER3A-HT THRU ER3M-HT TM Micro Commercial Components RATINGS AND CHARACTERISTIC CURVES FIG.1- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 10W NONINDUCTIVE FIG.2- MAXIMUM AVERAGE FORWARD CURRENT DERATING trr AVERAGE FORWARD CURRENT. (A) 50W NONINDUCTIVE +0.5A (+) 50Vdc (approx) (-) (-) DUT PULSE GENERATOR (NOTE 2) 1W NON INDUCTIVE OSCILLOSCOPE (NOTE 1) 0 -0.25A (+) -1.0A NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms 1cm 3 2 1 25 50 75 100 125 150 175 O AMBIENT TEMPERATURE. ( C) 1.0 20 40 60 80 100 T -H 3D ER T~ -H 3A 1.0 .1 .01 120 ER ER 3G 3J -H -H T~ T ER 3M -H T Tj=25 0C 10 Tj=25 0C 10.0 ER INSTANTANEOUS FORWARD CURRENT. (A) Tj=100 0C 100 0.1 .4 .6 .8 1.0 FORWARD VOLTAGE. (V) .2 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) 1.2 1.4 FIG.6- TYPICAL JUNCTION CAPACITANCE FIG.4- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 175 JUNCTION CAPACITANCE.(pF) PEAK FORWARD SURGE CURRENT. (A) 4 100.0 1000 300 Single Phase Half Wave 60Hz Resistive or Inductive Load 0.375" (9.5mm) Lead Length 5 FIG.5- TYPICAL FORWARD CHARACTERISTICS FIG.3- TYPICAL REVERSE CHARACTERISTICS INSTANTANEOUS REVERSE CURRENT. ( A) SET TIME BASE FOR 5/ 10ns/ cm 6 200 100 150 125 ER 3A 100 ER 3J- 75 -HT HT ~E ~E R3 R3 50 G- HT M- HT 25 0 1 10 100 NUMBER OF CYCLES AT 60Hz 1000 0 .1 .5 1 2 5 10 20 50 100 200 500 REVERSE VOLTAGE. (V) www.mccsemi.com Revision: 1 2005/08/31