MIC8115 Micrel MIC8115 Microprocessor Reset Circuit General Description Features The MIC8115 is an inexpensive microprocessor supervisory circuit that monitors power supplies in microprocessor based systems. The function of this device is to assert a reset if the power supply drops below a designated reset threshold level or /MR is forced low. The MIC8115 has an active low /RESET output. The reset output is guaranteed to remain asserted for a minimum of 1100ms after VCC has risen above the designated reset threshold level. The MIC8115 comes in a 4-pin SOT-143 package. • • • • • • • Precision voltage monitor for 3.3V power supplies Specifically tailored to the AMD Elan SC500 Series /RESET remains valid with VCC as low as 1V 5µA typical supply current 1100ms minimum reset pulse width Manual reset input Available in 4-Pin SOT-143 Package Applications • • • • • Portable equipment Intelligent instruments Critical microprocessor power monitoring Printers/computers Embedded controllers Ordering Information Part Number Marking Operating Temp. Range Package Pb-Free MIC8115TU NT –40°C to +85°C 4-lead SOT-143 No MIC8115TUY NT –40°C to +85°C 4-lead SOT-143 Yes Typical Application VCC VCC VCC MIC8115 µP MR RESET RESET MIC8115 Typical Application Micrel, Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel + 1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com July 2005 1 MIC8115 MIC8115 Micrel Pin Configuration GND 1 4 VCC MIC8115 3 MR RESET 2 4-Lead SOT-143 Pin Description Pin Number Pin Name Pin Function 1 GND IC Ground Pin 2 /RESET /RESET goes low if either VCC falls below the supply reset threshold voltage or if /MR is asserted. /RESET remains asserted for one reset timeout period 1100ms min. After both VCC exceeds the supply reset threshold voltage and /MR is deasserted. 3 /MR Manual Reset Input. A logic low on /MR forces a reset. The reset will remain asserted as long as /MR is held low and for one reset timeout period (1100ms min.) after /MR goes high. This input can be shorted to ground via a switch or driven from CMOS or TTL logic. Pulled high internally through a 20kΩ resistor. Float if unused. 4 VCC Power supply Input. MIC8115 2 July 2005 MIC8115 Micrel Absolute Maximum Ratings(Note 1) Operating Ratings(Note 2) Terminal Voltage (VCC) ...........................................................–0.3V to 6.0V (/MR) ..................................................–0.3V (VCC + 0.3V) Input Current (VCC, /MR) ............................................ 20mA Output Current (/RESET) ........................................... 20mA Rate of Rise (VCC) ..................................................100V/µS Lead Temperature (soldering, 10 sec.) ...................... 300°C Storage Temperature (TS) ........................ –65°C to +150°C ESD Rating .................................................................... 3kV Operating Temperature Range MIC8115TU ............................................ –40°C to +85°C Power Dissipation (TA = +70°C) .............................. 320mW Electrical Characteristics For typical values, VCC = 3.3V; TA = 25°C, bold values indicate –40°C ≤ TA ≤ +85°C; unless noted Symbol Parameter Condition VCC Operating Voltage Range TA = –40°C to 85°C VTH Reset Voltage Threshold ICC Supply Current tRST /RESET Output Voltage VOL /RESET Output Voltage /MR Minimum Pulse Width Typ 1 Reset Timeout Period VOH Min VCC = VTH min, ISINK = 1.2mA VCC = 1V, ISINK = 50µA, TA = –40°C to +85°C Units 5.5 V 5 15 µA 3.00 3.08 3.15 V 1100 1700 2500 ms 0.8×VCC ISOURCE = 500µA Max V 0.3 V 0.3 V 10 /MR to Reset Delay µs 0.5 /MR Input Threshold, VIH 0.7×VCC /MR Pull-Up Resistance 10 /MR Input Threshold, VIL /MR Glitch Immunity V 20 100 Note 1. Exceeding the absolute maximum rating may damage the device. Note 2. The device is not guaranteed to function outside its operating rating. Note 3. Devices are ESD sensitive. Handling precautions recommended. Human body model, 1.5k in series with 100pF. µs 0.25×VCC 30 kΩ ns Timing Diagram VCC VTH /MR /RESET July 2005 tRST tRST 3 MIC8115 MIC8115 Micrel Functional Diagram VCC MR (3) RESET GENERATOR RESET (2) + VCC (4) Reset Threshold (V) - GND (1) MIC8115 4 July 2005 MIC8115 Micrel Applications Information /RESET Valid at Low Voltage A resistor can be added from the /RESET pin-to-the ground to ensure the /RESET output remains low with VCC down to 0V. A 100kΩ resistor connected from /RESET-to-ground is recommended. The resistor should be large enough not to load the /RESET output and small enough to pull-down any stray leakage currents. Microprocessor Reset The /RESET pin is asserted whenever VCC falls below the reset threshold voltage. The reset pin remains asserted for a period of 1100ms after VCC has risen above the reset threshold voltage. The reset function ensures the microprocessor is properly reset and powers up into a known condition after a power failure. /RESET will remain valid with VCC as low as 1V. VCC Transients The MIC8115 is relatively immune to the negative-going VCC glitches below the reset threshold. Typically, a negative-going transient 125mV below the reset threshold with a duration of 20µs or less will not cause a reset. VCC VCC VCC MIC81 15 µP RESET RESET 100K /RESET Valid to VCC = 0V July 2005 5 MIC8115 MIC8115 Micrel Package Information 0.950 (0.0374) TYP 1.40 (0.055) 2.50 (0.098) 1.20 (0.047) 2.10 (0.083) CL CL DIMENSIONS: MM (INCH) 1.12 (0.044) 0.81 (0.032) 3.05 (0.120) 2.67 (0.105) 0.800 (0.031) TYP 0.400 (0.016) TYP 3 PLACES 8 0 0.10 (0.004) 0.013 (0.0005) 0.150 (0.0059) 0.089 (0.0035) 0.41 (0.016) 0.13 (0.005) 4-Lead SOT-143 (UT) MICREL, INC. 1849 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL + 1 (408) 944-0800 FAX + 1 (408) 944-0970 WEB http://www.micrel.com The information furnished by Micrel in this datasheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not� reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is at Purchaser’s own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. © 2003 Micrel, Incorporated. MIC8115 6 July 2005