Micrel, Inc. SY10E451 SY100E451 SY10E451 6-BIT REGISTER DIFFERENTIAL DATA CLOCK FEATURES DESCRIPTION ■ ■ ■ ■ ■ ■ 1100MHz min. toggle frequency Extended 100E VEE range of –4.2V to –5.5V Differential inputs: data and clock VBB output for single-ended use Asynchronous Master Reset Fully compatible with industry standard 10KH, 100K ECL levels ■ Internal 75KΩ input pulldown resistors ■ Fully compatible with Motorola MC10E/100E451 ■ Available in 28-pin PLCC package The SY10/100E451 offer six D-type flip-flops with singleended outputs and differential data and clock inputs, designed for use in new, high-performance ECL systems. The registers are triggered by the rising edge of the CLK input. A logic HIGH on the Master Reset (MR) input resets all outputs to a logic LOW. The VBB output is provided for use as a reference voltage for single-ended reception of ECL signals to that device only. When used for this purpose, it is recommended that VBB is decoupled to VCC via a 0.01µF capacitor. BLOCK DIAGRAM PIN NAMES Pin D0 /D0 Q0 D R D1 /D1 Q1 D R D2 /D2 Q2 D R D3 /D3 SY100E451 Function D0–D5 + Data Input /D0–/D5 – Data Input CLK + Clock Input /CLK – Clock Input Q0–Q5 Data Outputs MR Master Reset Input VBB VBB Output VCCO VCC to Output Q3 D R D4 /D4 Q4 D R D5 /D5 Q5 D R CLK /CLK MR VBB M9999-032206 [email protected] or (408) 955-1690 Rev.: G 1 Amendment: /0 Issue Date: March 2006 SY10E451 SY100E451 Micrel, Inc. PACKAGE/ORDERING INFORMATION VCCO /D3 D3 /D5 D5 /D4 D4 Ordering Information(1) 25 24 23 22 21 20 19 17 28 1 Q5 Q4 Package Type Operating Range Package Marking Lead Finish SY10E451JI J28-1 Industrial SY10E451JI Sn-Pb SY10E451JITR(2) J28-1 Industrial SY10E451JI Sn-Pb SY100E451JI J28-1 Industrial SY100E451JI Sn-Pb J28-1 Industrial SY100E451JI Sn-Pb J28-1 Commercial SY10E451JC Sn-Pb 15 VCC Q3 SY100E451JITR 16 TOP VIEW PLCC J28-1 (2) 14 VCCO SY10E451JC 3 13 SY10E451JCTR(2) J28-1 Commercial SY10E451JC Sn-Pb 4 12 Q2 Q1 SY100E451JC J28-1 Commercial SY100E451JC Sn-Pb SY100E451JCTR(2) J28-1 Commercial SY100E451JC Sn-Pb SY10E451JY(3) J28-1 Industiral SY10E451JY with Pb-Free bar-line indicator Matte-Sn SY10E451JYTR(2, 3) J28-1 Industrial SY10E451JY with Pb-Free bar-line indicator Matte-Sn SY100E451JY(3) J28-1 Industrial SY100E451JY with Pb-Free bar-line indicator Matte-Sn SY100E451JYTR(2, 3) J28-1 Industrial SY100E451JY with Pb-Free bar-line indicator Matte-Sn 6 7 8 9 10 11 VCCO Q0 /D0 5 D2 2 /D2 MR NC D0 18 /D1 /CLK VEE 26 27 D1 CLK VBB Part Number 28-Pin PLCC (J28-1) Notes: 1. Contact factory for die availability. Dice are guaranteed at TA = 25°C, DC Electricals only. 2. Tape and Reel. 3. Pb-Free package is recommended for new designs. M9999-032206 [email protected] or (408) 955-1690 2 SY10E451 SY100E451 Micrel, Inc. DC ELECTRICAL CHARACTERISTICS VEE = VEE (Min.) to VEE (Max.); VCC = VCCO = GND TA = –40°C Symbol Parameter Min. VBB Output Reference 10E Voltage 100E IIH Input HIGH Current IEE Power Supply Current VCMR Common Mode Range(1) Typ. Max. 10E 100E TA = 0°C TA = 25°C Max. Min. Typ. TA = +85°C Min. Typ. –1.38 –1.38 — — — — 150 — — 150 — — 84 84 101 101 — — 84 84 –2.0 — –0.4 –2.0 — –1.27 –1.35 –1.26 –1.38 — — Max. Min. Typ. Max. Unit — — –1.19 –1.26 V — — 150 µA 101 101 — — 84 97 101 116 mA –0.4 –2.0 — –0.4 V –1.25 –1.31 –1.26 –1.38 Note: 1. VCMR is referenced to the most psitive side of the differential input signal. Normal operation is obtained when the “HIGH” input is within the VCMR range and the input swing is greater than VPP (min) and < 1V. AC ELECTRICAL CHARACTERISTICS VEE = VEE (Min.) to VEE (Max.); VCC = VCCO = GND TA = –40°C Symbol Parameter Min. Typ. Max. TA = 0°C TA = 25°C TA = +85°C Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Unit MHz fMAX Max. Toggle Frequency 1100 1400 — 1100 1400 — 1100 1400 — tPD Propagation Delay to Output CLK (Diff) CLK (SE) MR 475 425 425 650 650 600 800 850 850 475 425 425 650 650 600 800 850 850 475 425 425 650 650 600 800 850 850 ps tS Set-up Time D 150 –100 — 150 –100 — 150 –100 — ps tH Hold Time D 250 100 — 250 100 — 250 100 — ps VPP (AC) Minimum Input Swing(1) 150 — — 150 — — 150 — — mV tRR Reset Recovery Time 750 600 — 750 600 — 750 600 — ps tPW Minimum Pulse Width CLK, MR 400 — — 400 — — 400 — — ps tskew Within-Device Skew(2) — 100 — — 100 — — 100 — ps tr tf Rise/Fall Time 20% to 80% 275 450 800 275 450 800 275 450 800 ps Notes: 1. Minimum input voltage for which AC parameters are guaranteed. 2. Within-device skew is defined as identical transitions on similar paths through a device. M9999-032206 [email protected] or (408) 955-1690 3 SY10E451 SY100E451 Micrel, Inc. 28-PIN PLCC (J28-1) Rev. 03 MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 TEL + 1 (408) 944-0800 FAX + 1 (408) 474-1000 WEB USA http://www.micrel.com The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is at Purchaser’s own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. © 2006 Micrel, Incorporated. M9999-032206 [email protected] or (408) 955-1690 4