TI TS5V330PWR

SCDS164A – MAY 2004 − REVISED MAY 2004
D Low Differential Gain and Phase
D
D
D
D
15
3
14
4
13
5
12
6
11
7
10
8
9
VCC
EN
S1D
S2D
DD
S1C
S2C
DC
RGY PACKAGE
(TOP VIEW)
S1A
S2A
DA
S1B
S2B
DB
VCC
D
16
2
1
16
15 EN
14 S2D
2
3
13 S2D
12 DD
4
5
6
7
8
9
11 S1C
10 S2C
DC
D
D
D
1
IN
D
IN
S1A
S2A
DA
S1B
S2B
DB
GND
GND
D
D
D
D, DBQ, OR PW PACKAGE
(TOP VIEW)
(DG = 0.64%, DP = 0.1 Degrees Typ)
Wide Bandwidth (BW = 300 MHz Min)
Low Crosstalk (XTALK = −63 dB Typ)
Low Power Consumption
(ICC = 3 µA Max)
Bidirectional Data Flow, With Near-Zero
Propagation Delay
Low ON-State Resistance (ron = 3 Ω Typ)
VCC Operating Range From 4.5 V to 5.5 V
Ioff Supports Partial-Power-Down Mode
Operation
Data and Control Inputs Provide
Undershoot Clamp Diode
Control Inputs Can Be Driven by TTL or
5-V/3.3-V CMOS Outputs
Latch-Up Performance Exceeds 100 mA Per
JESD 78, Class II
ESD Performance Tested Per JESD 22
− 2000-V Human-Body Model
(A114-B, Class II)
− 1000-V Charged-Device Model (C101)
Suitable for Both RGB and
Composite-Video Switching
description/ordering information
The TI TS5V330 video switch is a 4-bit 1-of-2 multiplexer/demultiplexer with a single switch-enable (EN) input.
When EN is low, the switch is enabled and the D port is connected to the S port. When EN is high, the switch
is disabled and the high-impedance state exists between the D and S ports. The select (IN) input controls the
data path of the multiplexer/demultiplexer.
ORDERING INFORMATION
QFN − RGY
SOIC − D
−40°C to 85°C
ORDERABLE
PART NUMBER
PACKAGE†
TA
SSOP (QSOP) − DBQ
TSSOP − PW
Tape and reel
TS5V330RGYR
Tube
TS5V330D
Tape and reel
TS5V330DR
Tape and reel
TS5V330DBQR
Tube
TS5V330PW
Tape and reel
TS5V330PWR
TOP-SIDE
MARKING
TE330
TS5V330
TE330
TE330
† Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines
are available at www.ti.com/sc/package.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright  2004, Texas Instruments Incorporated
!"# $"%&! '#(
'"! ! $#!! $# )# # #* "#
'' +,( '"! $!#- '# #!#&, !&"'#
#- && $##(
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
SCDS164A – MAY 2004 − REVISED MAY 2004
description/ordering information (continued)
Low differential gain and phase make this switch ideal for composite and RGB video applications. This device
has wide bandwidth and low crosstalk, making it suitable for high-frequency applications as well.
This device is fully specified for partial-power-down applications using Ioff. The Ioff feature ensures that
damaging current will not backflow through the device when it is powered down. This switch maintains isolation
during power off.
To ensure the high-impedance state during power up or power down, EN should be tied to VCC through a pullup
resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.
FUNCTION TABLE
INPUTS
EN
IN
INPUT/OUTPUT
D
FUNCTION
L
L
S1
D port = S1 port
L
H
S2
D port = S2 port
H
X
Z
Disconnect
PIN DESCRIPTIONS
PIN NAME
2
DESCRIPTION
S1, S2
Analog video I/Os
D
Analog video I/Os
IN
Select input
EN
Switch-enable input
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SCDS164A – MAY 2004 − REVISED MAY 2004
PARAMETER DEFINITIONS
DESCRIPTION
PARAMETER
ron
Resistance between the D and S ports, with the switch in the ON state
IOZ
IOS
VIN
Output leakage current measured at the D and S ports, with the switch in the OFF state
VEN
CIN
Voltage at the EN pin
Short-circuit current measured at the I/O pins
Voltage at the IN pin
Capacitance at the control (EN, IN) inputs
COFF
Capacitance at the analog I/O port when the switch is OFF
CON
Capacitance at the analog I/O port when the switch is ON
VIH
VIL
Minimum input voltage for logic high for the control (EN, IN) inputs
Vhys
VIK
Hysteresis voltage at the control (EN, IN) inputs
Minimum input voltage for logic low for the control (EN, IN) inputs
I/O and control (EN, IN) inputs diode clamp voltage
VI
VO
Voltage applied to the D or S pins when D or S is the switch input
IIH
IIL
Input high leakage current of the control (EN, IN) inputs
II
IO
Ioff
Current into the D or S pins when D or S is the switch input
tON
tOFF
BW
Voltage applied to the D or S pins when D or S is the switch output
Input low leakage current of the control (EN, IN) inputs
Current into the D or S pins when D or S is the switch output
Output leakage current measured at the D or S ports, with VCC = 0
Propagation delay measured between 50% of the digital input to 90% of the analog output when switch is turned ON
Propagation delay measured between 50% of the digital input to 90% of the analog output when switch is turned OFF
Frequency response of the switch in the ON state measured at −3 dB
XTALK
Unwanted signal coupled from channel to channel. Measured in −dB. XTALK = 20 log VO/VI. This is a nonadjacent
crosstalk.
OIRR
Off isolation is the resistance (measured in −dB) between the input and output with the switch OFF.
DG
Magnitude variation between analog input and output pins when the switch is ON and the dc offset of composite-video
signal varies at the analog input pin. In the NTSC standard, the frequency of the video signal is 3.58 MHz, and dc offset is
from 0 to 0.714 V.
DP
Phase variation between analog input and output pins when the switch is ON and the dc offset of composite-video signal
varies at the analog input pin. In the NTSC standard, the frequency of the video signal is 3.58 MHz, and dc offset is from 0
to 0.714 V.
ICC
Static power-supply current
ICCD
Variation of ICC for a change in frequency in the control (EN, IN) inputs
∆ICC
This is the increase in supply current for each control input that is at the specified voltage level, rather than VCC or GND.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
SCDS164A – MAY 2004 − REVISED MAY 2004
functional diagram (positive logic)
2
4
S1A
DA
3
S2A
DB
7
5
S1B
6
S2B
9
11
DC
10
DD
12
14
13
IN
1
15
Control
Logic
EN
4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
S1C
S2C
S1D
S2D
SCDS164A – MAY 2004 − REVISED MAY 2004
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 7 V
Control input voltage range, VIN (see Notes 1 and 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 7 V
Switch I/O voltage range, VI/O (see Notes 1, 2, and 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 7 V
Control input clamp current, IIK (VIN < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −50 mA
I/O port clamp current, II/OK (VI/O < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −50 mA
ON-state switch current, II/O (see Note 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±128 mA
Continuous current through VCC or GND terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±100 mA
Package thermal impedance, θJA (see Note 5): D package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73°C/W
(see Note 5): DBQ package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90°C/W
(see Note 5): PW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108°C/W
(see Note 6): RGY package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39°C/W
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltages are with respect to ground, unless otherwise specified.
2. The input and output voltage ratings may be exceeded if the input and output clamp-current ratings are observed.
3. VI and VO are used to denote specific conditions for VI/O.
4. II and IO are used to denote specific conditions for II/O.
5. The package thermal impedance is calculated in accordance with JESD 51-7.
6. The package thermal impedance is calculated in accordance with JESD 51-5.
recommended operating conditions (see Note 7)
MIN
MAX
UNIT
VCC
VIH
Supply voltage
4
5.5
V
High-level control input voltage (EN, IN)
2
5.5
V
VIL
VANALOG
Low-level control input voltage (EN, IN)
0
0.8
V
Analog I/O voltage
0
2
V
TA
Operating free-air temperature
−40
85
°C
NOTE 7: All unused control inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report,
Implications of Slow or Floating CMOS Inputs, literature number SCBA004.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
SCDS164A – MAY 2004 − REVISED MAY 2004
electrical characteristics over recommended operating free-air temperature range, VCC = 5 V ±10%
(unless otherwise noted)
PARAMETER
VIK
Vhys
EN, IN
IIH
IIL
EN, IN
TEST CONDITIONS
MIN
VCC = 4.5 V,
IIN = −18 mA
VCC = 5.5 V,
VCC = 5.5 V,
VIN and VEN = VCC
VIN and VEN = GND
IOZ‡
VCC = 5.5 V,
VO = 0 to 5.5 V,
VI = 0,
Switch OFF
IOS§
VCC = 5.5 V,
VO = 0.5 VCC,
VI = 0,
Switch ON
Ioff
ICC
VCC = 0,
VCC = 5.5 V,
VO = 0 to 5.5 V,
II/O = 0,
VI = 0
Switch ON or OFF
VCC = 5.5 V,
VCC = 5.5 V,
VEN = GND,
One input at 3.4 V,
Other inputs at VCC or GND
VIN or VEN = 0,
f = 1 MHz
∆ICC
EN, IN
EN, IN
EN, IN
EN, IN
D port
UNIT
−1.8
V
D and S ports open,
µA
±1
µA
±1
µA
mA
VIN input switching 50% duty cycle
1
µA
3
µA
2.5
mA
0.25
mA/
MHz
3.5
pF
6
f = 1 MHz,
Outputs open
Switch OFF
CON
VI = 0,
f = 1 MHz,
Outputs open
Switch ON
ron¶
VCC = 4.5 V
VI = 1 V,
VI = 2 V,
IO = 13 mA,
IO = 26 mA,
S port
mV
±1
50
VI = 0,
COFF
MAX
150
ICCD
CIN
TYP†
pF
4
14
pF
RL = 75 Ω
3
7
RL = 75 Ω
7
10
Ω
VI, VO, II, and IO refer to I/O pins.
† All typical values are at VCC = 5 V (unless otherwise noted), TA = 25°C.
‡ For I/O ports, IOZ includes the input leakage current.
§ The IOS test is applicable to only one ON channel at a time. The duration of this test is less than one second.
¶ Measured by the voltage drop between the D and S terminals at the indicated current through the switch. ON-state resistance is determined by
the lower of the voltages of the two (D or S) terminals.
switching characteristics over recommended operating free-air temperature range,
VCC = 5 V ±10%, RL = 75 Ω, CL = 20 pF (unless otherwise noted) (see Figure 5)
FROM
(INPUT)
TO
(OUTPUT)
tON
S
tOFF
S
PARAMETER
MIN
TYP
MAX
UNIT
D
2.5
6
ns
D
1.1
6
ns
dynamic characteristics over recommended operating free-air temperature range, VCC = 5 V ±10%
(unless otherwise noted)
PARAMETER
DG #
TEST CONDITIONS
RL = 150 Ω,
f = 3.58 MHz, see Figure 6
DP#
BW
RL = 150 Ω,
f = 3.58 MHz, see Figure 6
XTALK
OIRR
RL = 150 Ω,
f = 10 MHz,
RL = 150 Ω,
f = 10 MHz, see Figure 9
MIN
0.64
0.1
RL = 150 Ω, see Figure 7
300
RIN = 10 Ω, see Figure 8
† All typical values are at VCC = 5 V (unless otherwise noted), TA = 25°C.
# DG and DP are expressed in absolute magnitude.
6
TYP†
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MAX
UNIT
%
Deg
MHz
−63
dB
−60
dB
SCDS164A – MAY 2004 − REVISED MAY 2004
OPERATING CHARACTERISTICS
0
−1
−20
−3
−30
−4
−40
Gain
−50
−6
−7
1
0.06
−0.3
0.05
−0.4
0.04
−0.5
0.03
−0.6
0.02
−0.7
Differential Gain
−0.8
0.01
−0.9
0.00
−0.01
−1.0
−60
1000
10
100
Frequency − MHz
0.07
Differential Phase
−0.2
0
160
−10
140
Phase
120
−20
100
−30
80
−50
60
−60
Off Isolation
40
0.7
0.8
0.9
1
250
200
150
−40
−50
Phase
100
−60
Crosstalk
−70
20
−80
0
1000
−90
−80
100
Frequency − MHz
0.6
−10
Crosstalk − dB
−30
10
0.5
0
Phase − Deg
Off Isolation − dB
−20
1
0.4
Figure 2. Differential Gain/Phase vs VBIAS
0
−90
0.3
Differential Phase at 0.714, 0.056 Degree
Differential Gain at 0.714, −0.63%
Figure 1. Gain/Phase vs Frequency
−70
0.2
VBIAS − V
Phase at −3-dB Frequency, 35 Degrees
Gain −3 dB at 460 MHz
−40
0.1
1
10
100
Frequency − Mhz
Phase − Deg
−5
Differential Gain − %
Phase
Phase − Deg
Gain − dB
−0.1
−10
−2
0.08
0.0
Differential Phase − Deg
0
50
0
1000
Phase at 10 MHz, −90.4 Degrees
Crosstalk at 10 MHz, −63.9 dB
Phase at 10 MHz, 88.5 Degrees
Off Isolation at 10 MHz, −60 dB
Figure 3. Off Isolation vs Frequency
POST OFFICE BOX 655303
Figure 4. Crosstalk vs Frequency
• DALLAS, TEXAS 75265
7
SCDS164A – MAY 2004 − REVISED MAY 2004
PARAMETER MEASUREMENT INFORMATION
VCC
Input Generator
VIN
50 Ω
IN
50 Ω
VG1
S1
DUT
VS1
D
S2
VO
CL
(see Note A)
EN
RL
VS2
TEST
VCC
RL
CL
VS1
VS2
tON
5 V ± 0.5 V
5 V ± 0.5 V
75
75
20
20
GND
3V
3V
GND
tOFF
5 V ± 0.5 V
5 V ± 0.5 V
75
75
20
20
GND
3V
3V
GND
TEST CIRCUIT
3V
Output
Control
(VIN)
50%
50%
0V
tON
Analog Output
Waveform
(VO)
tOFF
90%
90%
VOH
0V
VOLTAGE WAVEFORMS
tON AND tOFF TIMES
NOTES: A. CL includes probe and jig capacitance.
B. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 ns.
C. The outputs are measured one at a time, with one transition per measurement.
Figure 5. Test Circuit and Voltage Waveforms
8
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SCDS164A – MAY 2004 − REVISED MAY 2004
PARAMETER MEASUREMENT INFORMATION
EXT TRIGGER
VBIAS
BIAS
Network Analyzer
(HP8753ES)
Sawtooth
Waveform Generator
P1
P2
VCC
S1A
DA
RL = 150 Ω
IN
DUT
VIN
EN
VEN
NOTE A: For additional information on measurement method, refer to the TI application report, Measuring Differential Gain and Phase, literature
number SLOA040.
Figure 6. Test Circuit for Differential Gain/Phase Measurement
Differential gain and phase are measured at the output of the ON channel. For example, when VIN = 0, VEN = 0, and
DA is the input, the output is measured at S1A.
HP8753ES setup
Average = 20
RBW = 300 Hz
ST = 1.381 s
P1 = −7 dBM
CW frequency = 3.58 MHz
sawtooth waveform generator setup
VBIAS = 0 to 1 V
Frequency = 0.905 Hz
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
9
SCDS164A – MAY 2004 − REVISED MAY 2004
PARAMETER MEASUREMENT INFORMATION
EXT TRIGGER
BIAS
VBIAS
Network Analyzer
(HP8753ES)
P1
P2
VCC
S1A
DA
RL = 150 Ω
IN
DUT
VIN
EN
VEN
Figure 7. Test Circuit for Frequency Response (BW)
Frequency response is measured at the output of the ON channel. For example, when VIN = 0, VEN = 0, and DA is
the input, the output is measured at S1A. All unused analog I/O ports are left open.
HP8753ES setup
Average = 4
RBW = 3 kHz
VBIAS = 0.35 V
ST = 2 s
P1 = 0 dBM
10
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SCDS164A – MAY 2004 − REVISED MAY 2004
PARAMETER MEASUREMENT INFORMATION
EXT TRIGGER
BIAS
VBIAS
Network Analyzer
(HP8753ES)
P1
P2
VCC
DA
S1A
RL = 150 Ω
IN
50 Ω†
VIN
EN
DUT
VEN
DB
S1B
RIN = 10 Ω
RL = 150 Ω
† A 50-Ω termination resistor is needed for the network analyzer.
Figure 8. Test Circuit for Crosstalk (XTALK)
Crosstalk is measured at the output of the nonadjacent ON channel. For example, when VIN = 0, VEN = 0, and DA
is the input, the output is measured at S1B. All unused analog input (D) ports and output (S) ports are connected to
GND through 10-Ω and 50-Ω pulldown resistors, respectively.
HP8753ES setup
Average = 4
RBW = 3 kHz
VBIAS = 0.35 V
ST = 2 s
P1 = 0 dBM
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
11
SCDS164A – MAY 2004 − REVISED MAY 2004
PARAMETER MEASUREMENT INFORMATION
EXT TRIGGER
BIAS
VBIAS
Network Analyzer
(HP8753ES)
P1
P2
VCC
S1A
DA
RL = 150 Ω
IN
DUT
VIN
S2A
EN
RL = 150 Ω
50 Ω†
VEN
† A 50-Ω termination resistor is needed for the network analyzer.
Figure 9. Test Circuit for Off Isolation (OIRR)
Off-isolation is measured at the output of the OFF channel. For example, when VIN = VCC, VEN = 0, and DA is the
input, the output is measured at S1A. All unused analog input (D) ports are left open, and output (S) ports are
connected to GND through 50-Ω pulldown resistors.
HP8753ES setup
Average = 4
RBW = 3 kHz
VBIAS = 0.35 V
ST = 2 s
P1 = 0 dBM
12
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MSOI004E JANUARY 1995 − REVISED MAY 2002
DBQ (R−PDSO−G**)
PLASTIC SMALL−OUTLINE PACKAGE
0.012 (0,30)
0.008 (0,20)
0.025 (0,64)
0.005 (0,13)
13
24
0.244 (6,20)
0.228 (5,80)
0.157 (3,99)
0.150 (3,81)
0.008 (0,20) NOM
Gauge Plane
1
12
0.010 (0,25)
A
0°−8°
0.035 (0,89)
0.016 (0,40)
0.069 (1,75) MAX
Seating Plane
0.010 (0,25)
0.004 (0,10)
0.004 (0,10)
PINS **
16
20
24
28
A MAX
0.197
(5,00)
0.344
(8,74)
0.344
(8,74)
0.394
(10,01)
A MIN
0.189
(4,80)
0.337
(8,56)
0.337
(8,56)
0.386
(9,80)
M0−137
VARIATION
AB
AD
AE
AF
DIM
D
4073301/F 02/2002
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion not to exceed 0.006 (0,15).
D. Falls within JEDEC MO−137.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
MECHANICAL DATA
MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999
PW (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
14 PINS SHOWN
0,30
0,19
0,65
14
0,10 M
8
0,15 NOM
4,50
4,30
6,60
6,20
Gage Plane
0,25
1
7
0°– 8°
A
0,75
0,50
Seating Plane
0,15
0,05
1,20 MAX
PINS **
0,10
8
14
16
20
24
28
A MAX
3,10
5,10
5,10
6,60
7,90
9,80
A MIN
2,90
4,90
4,90
6,40
7,70
9,60
DIM
4040064/F 01/97
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion not to exceed 0,15.
Falls within JEDEC MO-153
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright  2004, Texas Instruments Incorporated