NEL PJ-B2987

CRYSTAL CLOCK OSCILLATORS
Data Sheet 0350C
Rev. G
Differential Positive ECL (DPECL)
Fast Edge
PJ-B2980 Series
Description
The PJ-B2980 Series of quartz crystal oscillators provide DPECL Fast Edge compatible signals. Systems
designers may now specify space-saving, cost-effective packaged PECL oscillators to meet their timing
requirements.
Features
• Wide frequency range–60.0MHz to 312.5MHz
• User specified tolerance available
• Space-saving alternative to discrete component
oscillators
• High shock resistance, to 1000g
• 2.5 volt operation
• Metal lid electrically connected to ground to
reduce EMI
• High Reliability - NEL HALT/HASS qualified for
crystal oscillator start-up conditions
• Low Jitter - Wavecrest jitter characterization
available
• Overtone technology
• High Q Crystal actively tuned oscillator circuit
• Power supply decoupling internal
• No internal PLL avoids cascading PLL problems
• High frequencies due to proprietary design
• Gold plated pads
• RoHS Compliant, Lead Free Construction
Electrical Connection
Pin
Connection
1
2
3
4
5
6
Enable/Disable
N.C.
VEE /Ground
Output
/Output
VCC
357 Beloit Street, P.O. Box 457, Burlington, WI 53105-0457 U.S.A. Phone 262/763-3591 FAX 262/763-2881
Email: [email protected] www.nelfc.com
Data Sheet 0350C
CRYSTAL CLOCK OSCILLATORS
Rev. G
PJ-B2980 Series Continued
Differential Positive ECL (DPECL) Fast Edge
Operating Conditions and Output Characteristics
Electrical Characteristics
Parameter
Frequency
Duty Cycle
Logic 0 (2)
Logic 1(2)
Rise & Fall Time
Tpd (4)
Jitter, RMS(3)
Enable Voltage(5)
Disable Voltage
Frequency Stability (1)
Symbol
Conditions
Min
--------60.0MHz
[email protected] VCC-1.29V
45/55%
VOL
--------VOH
----VCC -1.025V
tr,tf 20-80%VO with 50 ohm load to VCC-2V -------------200 psec
----------------with VEE = 0V
1.6V
--------with VEE = 0V
dF/F
Overall conditions including:
-100ppm
voltage, calibration, temp.,
10 yr aging, shock, vibration
Typical
-----------------------------------------
Max
312.5MHz
55/45%
VCC -1.62V
----1 ns
+200 psec
1 psec
----0.4V
+100ppm
Typical
2.5V
-----
Max
2.625V
80 mA
---------------------
±50.0 mA
70°C
125°C
210 mW
253°C
2 ms
10 ms
General Characteristics
Parameter
Supply Voltage
Supply Current
Output current
Operating temperature
Storage temperature
Power Dissipation
Solder temperature
Load
Start-up time
Symbol
VCC
ICC
Conditions
Min
----2.375V
50 ohm termination
0.0 mA
To 2.00V below VCC
IO
Low level Output Current 0.0 mA
TA
-----0°C
-----55°C
TS
--------PD
TL
4 minutes
----50 Ohm to VCC-2V or Thevenin Equivalent, Bias Required
tS
---------
Environmental and Mechanical Characteristics
Mechanical Shock
Thermal Shock
Vibration
Hermetic Seal
Per MIL-STD-202, Method 213, Condition E
Per MIL-STD-883, Method 1011, Condition A
0.060" double amplitude 10 Hz to 55 Hz, 35g’s 55Hz to 2000 Hz
Leak rate less than 1 x 10 -8 atm.cc/sec of helium
Footnotes:
1) Standard frequency stability (±20,±25,±50ppm & others available)
2) VOL, VOH, referenced to ground (VEE) with VCC = 2.5V
3) Jitter performance is frequency dependent. Please contact factory for full Wavecrest characterization.
RMS jitter bandwidth of 12kHz to 20MHz.
4) Tpd is phse shift between the falling edge of pin 4 at 2.0V and the rising edge of pin 5 at 2.01V.
5) Open to enable pin also enables the output.
6) Internal high frequency power source decoupling.
Creating a Part Number
PJ - B298X - FREQ
Package Code
PJ 6 J Lead SMD
Input Voltage
Code Specification
A
3.3V
B
2.5V
5V
Tolerance/Performance
0 ±100ppm 0-70°C
1 ±50ppm 0-70°C
7 ±25ppm 0-70°C
9 Customer Specific
A ±20ppm 0-70°C
B ±50ppm -40 to +85°C
C ±100ppm -40 to +85°C
357 Beloit Street, P.O. Box 457, Burlington, WI 53105-0457 U.S.A. Phone 262/763-3591 FAX 262/763-2881
Email: [email protected] www.nelfc.com