CRYSTAL CLOCK OSCILLATORS Data Sheet 0208E Rev. B LVDS with Tri-State PJ-A2D00 Series PRELIMINARY Description The PJ-A2D00 Series of quartz crystal oscillators provide LVDS compatible signals in a ceramic SMD package. Systems designers may now specify space-saving, cost-effective packaged LVDS oscillators to meet their timing requirements. Features • Wide frequency range–50.0MHz to 250.0MHz • User specified tolerance available • Will withstand vapor phase temperatures of 253°C for 4 minutes maximum • Space-saving alternative to discrete component oscillators • High shock resistance, to 3000g • 3.3 volt operation (other voltages available upon request) • Metal lid electrically connected to ground to reduce EMI • Enable/Disable (Tri-state) • LVDS output on pin 4, complement on Pin 5 • Low Jitter - Wavecrest jitter characterization available • High Reliability - NEL HALT/HASS qualified for crystal oscillator start-up conditions • Overtone technology • High Q Crystal actively tuned oscillator circuit • Power supply decoupling internal • No internal PLL avoids cascading PLL problems • High frequencies due to proprietary design • Gold plated leads - Solder dipped leads available upon request Electrical Connection Pin Connection 1 2 3 4 5 N.C. Enable/Disable Ground Output Output Complement VCC 6 357 Beloit Street, P.O. Box 457, Burlington, WI 53105-0457 U.S.A. Phone 262/763-3591 FAX 262/763-2881 Email: [email protected] www.nelfc.com Data Sheet 0208E CRYSTAL CLOCK OSCILLATORS PJ-A2D00 Series LVDS Rev. B Continued Operating Conditions and Output Characteristics Electrical Characteristics Parameter Frequency Duty Cycle(2) Logic 0 (2) Logic 1 (2) Differential Voltage (2) Disable Voltage Enable Voltage Rise & Fall Time (2) Tpd (4) Jitter, RMS(3) Enable (Low) voltage Disable (High) voltage Frequency Stability (1) Symbol Conditions ------------@ VO /2 VOL ----VOH ----VOD --------VIL VIH (or open) tr,tf 20-80%VO --------------------------------dF/F Overall conditions including: voltage, calibration, temp., 10 yr aging, shock, vibration Min 50.0MHz 45/55% 0.80V 1.25V 250 mV GND 2.0V -----0.5 ns --------2.00V -100ppm Typical ----------------------------0.8 ns --------------------- Max 250.0MHz 55/45% 1.10V 1.55V 450 mV 0.8V VCC 1.0 ns +0.5 ns 3 psec 800mV ----+100ppm Min 3.15V 0.0 mA 0.0 mA 0°C -55°C --------- Typical 3.3V ------------------------- Max 3.45V 80 mA ±50.0 mA 70°C 125°C 345 mW 300°C ----- 2 ms 10 ms General Characteristics Parameter Supply Voltage Supply Current Output current Operating temperature Storage temperature Power Dissipation Lead temperature Load Start-up time Symbol Conditions ----VCC ICC ----IO Continuous Output Current -----TA TS --------PD Soldering, 10 sec. TL 100 ohms across differential outputs tS ----- Environmental and Mechanical Characteristics Mechanical Shock Thermal Shock Vibration Soldering Condition Hermetic Seal Per MIL-STD-202, Method 213, Condition E Per MIL-STD-833, Method 1011, Condition A 0.060" double amplitude 10 Hz to 55 Hz, 35g’s 55Hz to 2000 Hz 300°C for 10 seconds Leak rate less than 1 x 10 -8 atm.cc/sec of helium Footnotes: 1) Standard frequency stability (±20,±25,±50ppm & others available) 2) With Load of 100 ohms across differential outputs. 3) Jitter performance is frequency dependent. Please contact factory for full Wavecrest characterization. 4) Tpd is phase shift between the falling edge of pin 4 and the rising edge of pin 5. Creating a Part Number PJ - A2D0X - FREQ Package Code PJ 6 J Lead SMD Input Voltage Code Specification A 3.3V 5V Tolerance/Performance 0 ±100ppm 0-70°C 1 ±50ppm 0-70°C 7 ±25ppm 0-70°C 9 Customer Specific A ±20ppm 0-70°C B ±50ppm -40 to +85°C C ±100ppm -40 to +85°C 357 Beloit Street, P.O. Box 457, Burlington, WI 53105-0457 U.S.A. Phone 262/763-3591 FAX 262/763-2881 Email: [email protected] www.nelfc.com