SMF3.0A SERIES SURFACE MOUNT TRANSIENT VOLTAGE SUPPRESSOR VOLTAGE CURRENT 3.0 to 170 Volts 200Watts FEATURES • For surface mounted applications in order to optimize board space. • Low profile paceage • Built-in strain relief • Low inductance • High temperature soldering : 260 OC/10 seconds at terminals • In compliance with EU RoHS 2002/95/EC directives MECHANICAL DATA • Case: JEDEC DO-219AB,Molded plastic over passivated junction. • Terminals: Solderable per MIL-STD-750, Method 2026 • Polarity: Color band denotes positive end (cathode) • Approx. Weight: 0.0168 gram • Standrad Packaging : 8mm tape (EIA-481) DEVICES FOR BIPOLARAPPLICATIONS Electrical characteristics apply in both directions MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25OC ambient temperature unless otherwise specified. Rating Symbol Value Units Peak Pulse Power Dissipation on T A = 25 O C (Notes 1,2,5, Fig.1) PPPM 200 Watts Peak Forward Surge Current per (Note 3) IFSM 20 Amps Peak Pulse Current on 10/1000s waveform(Note 1)Fig.2 IPPM see Table 1 Amps Steady State Power Dissipation (NOTE 4) PM(AV) 1.0 Watts Operating Junction and Storage Temperature Range TJ,TSTG -55 to +150 O RθJA 180 O Thermal resistance C C NOTES : 1.Non-repetitive current pulse, per Fig.3 and derated above T A =25 O C per Fig.2 . 2.Mounted on 5.0mm2 copper pads to each terminal. 3.8.3ms single half sine-wave, or equivalent square wave, duty cycle = 4 pulses per minutes maximum. 4.lead temperature at 75 OC =T L . 5.Peak pulse power waveform is 10/1000us . STAD-MAY.25.2007 PAGE . 1 SMF3.0A SERIES Part N umber V BR @ IT V R WM V IR @ VRWM Min . Ma x . IT V V mA µA VC @ IPP V Marking C ode A 200W Transient Voltage Suppressor SMF3.0A 3.0 4.1 4.5 10 400 8 25 HD SMF5.0A 5 6.4 7 10 400 9.2 21.7 HE SMF6.0A 6 6.7 7.4 10 400 10.3 19.4 HG SMF6.5A 6.5 7.2 8 10 250 11.2 17.9 HK SMF7.0A 7 7.8 8.6 10 100 12 16.7 HM SMF7.5A 7.5 8.3 9.2 1 50 12.9 15.5 HP SMF8.0A 8 8.9 9.8 1 25 13.6 14.7 HR SMF8.5A 8.5 9.4 10.4 1 10 14.4 13.9 HT SMF9.0A 9 10 11.1 1 5 15.4 13 HV SMF10A 10 11.1 12.3 1 2.5 17 11.8 HX SMF11A 11 12.2 13.5 1 2.5 18.2 11 HZ SMF12A 12 13.3 14.7 1 2.5 19.9 10.1 IE SMF13A 13 14.4 15.9 1 1 21.5 9.3 IG SMF14A 14 15.6 17.2 1 1 23.2 8.6 IK SMF15A 15 16.7 18.5 1 1 24.4 8.2 IM SMF16A 16 17.8 19.7 1 1 26 7.7 IP SMF17A 17 18.9 20.9 1 1 27.6 7.2 IR SMF18A 18 20 22.1 1 1 29.2 6.8 IT SMF20A 20 22.2 24.5 1 1 32.4 6.2 IV SMF22A 22 24.4 26.9 1 1 35.5 5.6 IX SMF24A 24 26.7 29.5 1 1 38.9 5.1 IZ SMF26A 26 28.9 31.9 1 1 42.1 4.8 JE SMF28A 28 31.1 34.4 1 1 45.4 4.4 JG SMF30A 30 33.3 36.8 1 1 48.4 4.1 JK SMF33A 33 36.7 40.6 1 1 53.3 3.8 JM SMF36A 36 40 44.2 1 1 58.1 3.4 JP SMF40A 40 44.4 49.1 1 1 64.5 3.1 JR SMF43A 43 47.8 52.8 1 1 69.4 2.9 JT SMF45A 45 50 55.3 1 1 72.7 2.8 JV SMF48A 48 53.3 58.9 1 1 77.4 2.6 JX SMF51A 51 56.7 62.7 1 1 82.4 2.4 JZ SMF54A 54 60 66.3 1 1 87.1 2.3 RE SMF58A 58 64.4 71.2 1 1 93.6 2.1 RG SMF60A 60 66.7 73.7 1 1 96.8 1.8 RK SMF64A 64 71.1 78.6 1 1 103 1.7 RM SMF70A 70 77.8 86 1 1 113 1.5 RP SMF75A 75 83.3 92.1 1 1 121 1.4 RR SMF78A 78 86.7 95.8 1 1 126 1.4 RT SMF85A 85 94.4 104 1 1 137 1.3 RV RX SMF90A 90 100 111 1 1 146 1.2 SMF100A 100 111 123 1 1 162 1.1 RZ SMF110A 110 122 135 1 1 177 1 SE SMF120A 120 133 147 1 1 193 0.9 SG SMF130A 130 144 159 1 1 209 0.8 SK SMF140A 150 167 185 1 1 243 0.7 SM SMF160A 160 178 197 1 1 259 0.7 SP SMF170A 170 189 209 1 1 275 0.6 SR STAD-MAY.25.2007 PAGE . 2 P PPM ,PEAK PULSE FORWARD,KW SMF3.0A SERIES 100 Non-Repetitve Pulse Wavefom Shown in Figure.3 T A = 25 O C 10 1.0 0.1 0.1 10 1.0 100 1000 10000 PEAK PULSE FORWARD (P PP) OR CURRENT (I PP) DERATING IN PERCENTAGE % 100 75 50 25 0 0 25 td,PULSE WIDTH, micro sec 75 100 125 150 175 200 O T A ,AMBIENT TEMPERATURE, C Fig.1 PEAK PULSE POWER RATING CURVE Fig.2 DERATING CURVE 10,000 150 I PPM ,PEAK PULSE CURRENT,% 50 O tf = 10usec Ha lf Va lue -Ip p 2 10/1000u se c Wa ve fo rm a s De fine d b ye R.E.A. 50 e -kt td 0 0 1.0 2.0 3.0 4.0 C J ,CAPACITANCE,p F Peak Value Ippm 100 T J = 25 C f= 1.0MHZ Vsig = 50mVp -p O T A = 25 C Pulse Width (td) is Defined as the Point where the Peak Current Decayst to 50% of Ipp 1,000 Me a sure d a t Ze ro Bia s 100 Me a sure d a t Sta nd -Off Vo lta ge (VRWM) T,TIME,ms Fig.3 PULSE WAVEFORM I FSM ,PEAK FORWARD SURGE CURRENT, AMPERES 10 1.0 2.0 5.0 10 20 50 100 200 50 V( RWM), REVERSE STAND-OFF VOLTAGE, VOLTS TJ= TJm a x 8.3m s Sing le Ha lf SinepWave JEDEC M e tho d 40 Fig.4 TYPICAL JUNCTION CAPACITANCE 30 20 10 0 1 2 4 10 20 40 100 NUMBER OF CYCLES AT 60Hz Fig.5 MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PLEASE REFER THE TVS APPLICATION NOTE IN PANJIT WEBSITE http://www.panjit.com/protection-transient-voltage-suppressors.html STAD-MAY.25.2007 PAGE . 3 SMF3.0A SERIES MOUNTING PAD LAYOUT ORDER INFORMATION • Packing information T/R - 10K per 13" plastic Reel T/R - 3K per 7" plastic Reel LEGAL STATEMENT Copyright PanJit International, Inc 2007 The information presented in this document is believed to be accurate and reliable. The specifications and information herein are subject to change without notice. Pan Jit makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose. Pan Jit products are not authorized for use in life support devices or systems. Pan Jit does not convey any license under its patent rights or rights of others. STAD-MAY.25.2007 PAGE . 4