Ordering number : ENA0191 Monolithic Linear IC LA2360M CAN Transceiver Overview The LA2360M is a CAN (Controller Area Network) transceiver. Functions [ Transmitter block ] • Low-pass filter (EMI prevention) • Output driver [ Receiver block ] • ATT • Comparator Features • Conforms to the ISO 11898 standard • Transmission rate: 1 Mbps Specifications Maximum Ratings at Ta = 25°C Parameter Maximum supply voltage Symbol Maximum applied voltage VCC max Vap Maximum applied voltage Vap (6, 7) Conditions Ratings Unit 6.0 V VCC V -8 to +18 V (pins 6 and 7) Allowable power dissipation Pd max *: Mounted on a circuit board, Ta ≤ 85°C 440 mW Operating temperature Topg -40 to +85 °C Storage temperature Tstg -55 to +150 °C 3 *: Circuit board: 39.8×50.0×1.6mm glass epoxy Notice: Please contact our company, when using the LA2360M in the body system or the power-train system. Any and all SANYO Semiconductor products described or contained herein do not have specifications that can handle applications that require extremely high levels of reliability, such as life-support systems, aircraft's control systems, or other applications whose failure can be reasonably expected to result in serious physical and/or material damage. Consult with your SANYO Semiconductor representative nearest you before using any SANYO Semiconductor products described or contained herein in such applications. SANYO Semiconductor assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor products described or contained herein. 92706 / 10606 MS OT 20051110-S00002 No.A0191-1/5 LA2360M Operating Conditions at Ta = 25°C Parameter Symbol Recommended supply voltage VCC Operating supply voltage range VCC op Conditions Ratings Unit 5.0 V 4.5 to 5.5 V Operating Characteristics at Ta = 25°C, VCC = 5.0V Parameter Symbol Ratings Conditions min typ Unit max Overall Current drain ICC Dominant; V1 = 1V, R8 = 0Ω 70 mA Recessive; V1 = 4V, R8 = 47kΩ 14 mA Recessive; V1 = 4V, R8 = 0kΩ 18 mA 70 µA VCC+0.3 V Standby; V8 = VCC, I1 = I4 = I5 = 0mA 30 30 50 DC transmitter block High-level input voltage V1IH Output -recessive Low-level input voltage V1IL Output -dominant 0.7VCC -0.3 0.3VCC V High-level input current I1IH V1 = 4V -200 +30 µA Low-level input current I1IL V1 = 1V -600 -100 µA CAN_H output voltage V7 V1 = 1V 2.75 4.5 V CAN_L output voltage V6 V1 = 1V 0.5 2.25 V Recessive state bus voltage V6, 7 V1 = 4V 2.0 3.0 V Pins 6 and 7 output voltage ∆V6, 7 V1 = 1V 1.5 3.0 V -500 +50 mV -120 mA 160 mA V difference V1 = 4V; With no 62Ω resistor Current when pin 7 grounded ISC7 V1 = 1V, V7 = -8V; VCC = 5V Current when pin 6 shorted to VCC ISC6 V1 = 1V, V6 = 18V DC receiver block Differential input voltage Vdiff (r) (recessive) Differential input voltage Vdiff (d) (dominant) Output -recessive -1.0 0.2 Output –recessive, 0V < (V6, V7) < 12V -1.0 0.1 V Output –dominant 0.9 5.0 V Output –dominant, 0V < (V6, V7) < 12V 1.0 5.0 V V High-level output voltage (pin 4) V4OH I4 = -100µA 0.8VCC VCC Low-level output voltage (pin 4) V4OL I4 = +100µA 0 0.2VCC Input hysteresis voltage Vdiff (hys) 50 80 150 V mV DC standby/slope control block High-speed mode input voltage V8 High-speed mode input current I8 V8 = 0V 0.3VCC V -500 µA Standby mode input voltage Vstb Slope control mode current Islope 8pin = 47kΩ 0.75VCC -200 -10 µA V Slope control mode voltage Vslope 8pin = 47kΩ 0.4VCC 0.6VCC V Continued on next page. No.A0191-2/5 LA2360M Continued from preceding page. Parameter Symbol Ratings Conditions min typ Unit max DC reference block Output reference voltage Vref V8 = 1V; -50µA < I5 < 50µA V8 = 4V; -5µA < I5 < 5µA 0.45VCC 0.55VCC V 0.4VCC 0.6VCC V 0.45 0.55 µs 4.5 5.5 µs AC transmitter block Pins 6 and 7 differential output twidth (diff) pulse width V8 = 1V, V1 = 1MHz V8 = 1V, V1 = 100kHz Rise delay time tonTXD Fall delay time toffTXD V8 = 1V, V1 = 1MHz 40 65 ns V8 = 1V, V1 = 100kHz 40 65 ns V8 = 1V, V1 = 1MHz 40 65 ns V8 = 1V, V1 = 100kHz 40 65 ns V8 = 1V, V1 = 1MHz 110 160 ns V8 = 1V, V1 = 100kHz 110 160 ns R8 = 47kΩ, V1 = 100kHz 360 500 ns R8 = 24kΩ, V1 = 100kHz 320 500 ns 90 160 ns AC receiver block (overall) (See note 1.) Rise delay time tonRXD Fall delay time toffRXD V8 = 1V, V1 = 1MHz V8 = 1V, V1 = 100kHz Pin 8 wakeup time from standby twake 90 160 ns R8 = 47kΩ, V1 = 100kHz 600 800 ns R8 = 24kΩ, V1 = 100kHz 500 800 ns 20 µs 3 µs V8 = 4V → 1V, V8 = 100kHz mode Receiver output response time to tdRXDL V1 = 4.0V, V8 = 4.0V [BUS] recessive → dominant a bus level change Note 1. With an input signal to the transmitter, in automatic send/receive mode Package Dimension unit:mm 3032D 5.0 5 0.63 4.4 6.4 8 4 (1.5) 0.35 0.15 1.7max 1.27 0.1 1 (0.65) SANYO : MFP8(225mil) No.A0191-3/5 LA2360M Block Diagram Pin Functions Pin No. Pin I/O 1 TXD I Transmission signal input Function Input from the CAN microcontroller Description 2 GND P GND System ground 3 VCC P Power supply 5V 4 RXD O Reception signal output Output to the CAN microcontroller 5 VREF O Reference voltage output 2.5V 6 CANL I/O Transmission signal output (L) Input and output of send and receive signals to the bus 7 CANH I/O Transmission signal output (H) Input and output of send and receive signals to the bus 8 RS I Mode switching resistor Slope control Controls standby mode No.A0191-4/5 LA2360M Specifications of any and all SANYO Semiconductor products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer's products or equipment. SANYO Semiconductor Co., Ltd. strives to supply high-quality high-reliability products. However, any and all semiconductor products fail with some probability. It is possible that these probabilistic failures could give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO Semiconductor products (including technical data,services) described or contained herein are controlled under any of applicable local export control laws and regulations, such products must not be exported without obtaining the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written permission of SANYO Semiconductor Co., Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO Semiconductor product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. SANYO Semiconductor believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. This catalog provides information as of January, 2006. Specifications and information herein are subject to change without notice. PS No.A0191-5/5