Ordering number : ENA0366 Monolithic Digital IC LB8503V DC Fan Motor Speed Control IC Overview The LB8503V is an improved functionality version of the LB8500 and LB8502 products that features the added functions listed below. The LB8503V supports both single-phase and three-phase applications. Added Functions • Supports origin shifting in the speed control function • Adds a dedicated pin for setting the soft start time This allows a longer start time to be set without reducing the response time when changing speed. • FG output pin added Functions and Features • Achieves linear speed control Applications can set the slope of the change in motor speed with change in the input duty. • Minimized speed fluctuations in the presence of line or load variations • Allows a minimum speed to be set • Soft start function • Settings using external capacitors and resistors (to support easier mass production of end products) • Supports both PWM duty and analog voltage control inputs Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to "standard application", intended for the use as general electronics equipment (home appliances, AV equipment, communication device, office equipment, industrial equipment etc.). The products mentioned herein shall not be intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee thereof. If you should intend to use our products for applications outside the standard applications of our customer who is considering such use and/or outside the scope of our intended standard applications, please consult with us prior to the intended use. If there is no consultation or inquiry before the intended use, our customer shall be solely responsible for the use. Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer' s products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer' s products or equipment. 31407 TI PC 20060207-S00003 No.A0366-1/20 LB8503V Specifications Absolute Maximum Ratings at Ta = 25°C Parameter Symbol Supply voltage VCC max Output current IO max Conditions Ratings Unit VCC pin E0 pin 18 V 3 mA FG output pin output voltage VFG max FGOUT pin 18 V FG output pin output current IFG max FGOUT pin 10 mA Allowable power dissipation Pd max When mounted on a circuit board *1 0.8 W Operating temperature Topr -30 to +95 °C Storage temperature Tstg -55 to +150 °C *1 Specified circuit board : 114.3 × 76.1 × 1.6mm3, glass epoxy. Allowable Operating Range at Ta = 25°C Parameter Symbol Conditions Ratings Unit Supply voltage range 1 VCC1 VCC pin 7.5 to 17 V Supply voltage range 2 VCC2 VCC pin, with VCC shorted to 6VREG 5.5 to 6.5 V Output current 2.5 mA IREG -5 mA CTL pin voltage VCTL 0 to 6VREG V LIM pin voltage VLIM 0 to 6VREG V VC1 pin voltage VCI 0 to 6VREG V 6V constant voltage output IO E0 pin current Electrical Characteristics at Ta = 25°C, VCC = 12V Parameter Symbol Ratings Conditions min Supply current Unit typ ICC max 5.5 6.5 mA 6.0 6.2 V mV 6V constant voltage output (VREG pin) Output voltage VREG 5.8 Line regulation ΔVREG1 VCC = 8 to 17V 40 100 Load regulation ΔVREG2 IO = -5 to 5mA 10 100 Temperature coefficient ΔVREG3 Design target* 0 mV mV/°C Integrating Amplifier Block (E01) Common-mode input voltage VICM 2.0 VREG V range High-level output voltage VOH(E01) IEO1 = -0.2mA Low-level output voltage VOL(E01) IEO1 = 0.2mA High-level output voltage VOH(E03) IEO1 = -0.2mA Low-level output voltage VOL(E03) IEO1 = 0.2mA VREG - 1.2 V VREG - 0.8 0.8 1.0 V Integrating Amplifier Block (E03) VREG - 1.2 V VREG - 0.8 0.8 1.0 V VREG V V FGIN pin High-level input voltage VFGH 3.0 Low-level input voltage VFGL 0 1.5 Input open voltage VFGO VREG - 0.5 VREG V Hysteresis VFGS 0.2 0.3 0.4 V High-level input current IFGH VFGIN = 6VREG -10 0 10 μA Low-level input current IFGL VFGIN = 0V -140 -110 μA FGOUT pin Output low saturation voltage VFG Output leakage current IFGL 0.2 0.3 V 10 μA Continued on next page. No.A0366-2/20 LB8503V Continued from preceding page. Parameter Symbol Ratings Conditions min Unit typ max RC pin High-level output voltage Low-level output voltage Clamp voltage VOH(RC) 3.2 3.45 3.7 V VOL(RC) 0.8 0.95 1.05 V VCLP(RC) 1.5 1.65 1.8 V VCTH 2.0 VREG V V CTL pin High-level input voltage Low-level input voltage VCTL 0 1.0 Input open voltage VCTO VREG - 0.5 VREG V High-level input current ICTH VFGIN = 6VREG 10 μA Low-level input current ICTL VFGIN = 0V -10 0 -140 -110 μA C pin High-level input voltage VOH(C) VREG - 0.3 VREG - 0.1 Low-level input voltage VOL(C) 1.8 2.0 IB(LIM) V 2.2 V -1 1 μA 2.0 VREG V LIM pin Input bias current Common-mode input voltage VILIM range SOFT pin Charge current IC(SOFT) Operation voltage range μA 1.4 VISOFT 2.0 VREG V IB(VCI) -1 1 μA 2.0 VREG V VCI pin Input bias current Common-mode input voltage VIVCI range VCO pin High-level output voltage VOH(VCO) VREG - 0.2 V Low-level output voltage VOL(VCO) 2.0 V * The design specification items are design guarantees and are not measured. Package Dimensions unit : mm (typ) 3178B Pd max – Ta 5.2 0.5 6.4 9 4.4 16 1 8 0.65 0.15 1.5max 0.22 Specified circuit board : 114.3×76.2×1.6mm3 glass epoxy board 0.8 0.6 0.4 0.2 0 – 20 0 20 40 60 80 100 Ambient temperature, Ta – °C 0.1 (1.3) (0.33) Allowable power dissipation, Pd max – W 1.0 SANYO : SSOP16(225mil) No.A0366-3/20 LB8503V Pin Assignment EO3 EO1 EI NC GND FGOUT FGIN LIM 16 15 14 13 12 11 10 9 LB8503V 1 2 3 4 5 6 7 8 RC SOFT VREG VCC CVI CVO CTL C Top view Pin Functions Pin No. Pin Description RC 1 One-shot multivibrator pulse width setting. Connect a resistor between this pin and VREG, and a capacitor between this SOFT 2 pin and ground. Soft start time setting. Connect a capacitor between this pin and VREG. VREG 3 6V regulator output. Connect a capacitor between this pin and ground for stabilization. VCC 4 Power supply. Connect a capacitor between this pin and ground for stabilization. CVI 5 Control voltage input CVO 6 Duty pulse signal smoothed voltage output CTL 7 Duty pulse signal input. The speed is controlled by the duty of this pulse signal. C 8 Duty pulse signal smoothing. Connect a capacitor between this pin and VREG. LIM 9 Minimum speed setting. Normally, the 6V regulator level is resistor divided to set this pin's input level. FGIN 10 FG pulse input FGOUT 11 FG pulse output GND 12 Grand pin NC 13 NC pin EI 14 One-shot multivibrator output and integrating amplifier input. A capacitor must be connected between this pin and EO for EO1 15 this integration. Integrating amplifier output. (For use with an accelerating driver IC if the command voltage becomes low (single-phase systems).) EO3 16 Integrating amplifier inverting output. (For use with an accelerating driver IC if the command voltage becomes high (three-phase systems).) No.A0366-4/20 LB8503V Block Diagrams and Application Examples Combination with an accelerating driver IC when the command voltage goes low (single-phase systems) LB8503V 12V VCC C4 VREG FGOUT VREG C5 6VREG EDGE FGIN R3 RC C3 FG FG One-shot multivibrator R1 EI C6 LIM R2 C2 VTH VREF C1 EO1 SOFT CVI R4 CVO VREG R5 EO3 C CTL signal CTL CTL GND I LB01769 No.A0366-5/20 LB8503V Combination with an accelerating driver IC when the command voltage goes high (three-phase systems) LB8503V 12V VCC C4 VREG FGOUT VREG 6VREG EDGE C5 FG FG FGIN R3 RC C3 One-shot multivibrator R1 EI C6 LIM R2 C1 R4 SOFT CVI CVO C2 EO1 VREF VREG R5 VCTL EO3 C CTL signal CTL CTL GND I LB01770 No.A0366-6/20 LB8503V Speed Control Diagrams The slope is determined by the external constant connected to the RC pin. (RPM) For a larger RC time constant For a smaller RC time constant Speed Minimum speed Determined by the LIM pin voltage Low← CTL pin (PWM DUTY) High← EO1 pin voltage (V) Low← EO3 pin voltage (V) 0% Set minimum speed →High →Low →High Variable speed Low on duty 100% Full speed High on duty CTL pin 6VREG LIM voltage EO pin EO1 voltage 0V Startup Timing (soft start) VCC pin CTL pin SOFT pin Stop Stop Full speed Soft start The slope can be changed with the capacitor connected to the C pin (A larger capacitor increases the slope.) Full speed No.A0366-7/20 LB8503V Supplementary Operational Descriptions The LB8503V accepts a duty pulse input and an FG signal from the driver IC, and generates the driver IC control voltage so that the FG period (motor speed) becomes proportional to the control voltage. Driver IC LB8503V FGIN CTL signal FG CTL Closed feedback loop EO VTH As shown in the figure below, the LB8503V generates a pulse signal from edges on the FG signal and then generates a pulse width waveform determined by the RC time constant in a one-shot multivibrator. The LB8503V then integrates that pulse waveform to create the output driver IC control voltage (a DC voltage). FG EDGE pulse Slope due to the RC time constant RC pin One-shot multivibrator TRC(s) = 0.85RC It is also possible to change the slope of the VCTL/speed relationship as shown in the speed control diagram in the previous section by changing the pulse width with the RC time constant. Note, however, that since pulses determined by this RC time constant are used, variation in the RC components will appear as speed control errors. No.A0366-8/20 LB8503V Pin Setting Procedures (Provided for reference purposes) [RC pin] The slope in the speed control diagram is determined by the RC pin time constant. (RPM) Motor full speed 0% 100% CTL Duty (%) I LB01771 1. Determine the FG signal frequency (fFG (Hz)) at the motor's highest speed. (When 2 FG pulses are created on each motor revolution.) fFG(Hz)=2rpm/60 .........................................................(1) 2. Determine the time constant for the RC pin. (Let DUTY be the control duty at the highest motor speed. For example, 100% = 1.0, 60% = 0.6) R×C=DUTY/(3×0.85×fFG) ............................................. (2) 3. Determine the resistor and capacitor values The range of capacitors that can be used is from 0.01 to 0.015 µF due to the charge capabilities of the RC pin circuit. Therefore, an appropriate resistor value can be determined from either (3) or (4) below from the result obtained in step 2 above. R=(R×C)/0.01μF....................................................... (3) R=(R×C)/0.015μF..................................................... (4) Note that the temperature characteristics of the curve are determined by the temperature characteristics of the capacitor connected to the RC pin. A capacitor with excellent temperature characteristics must be used to minimize motor speed variation with temperature. No.A0366-9/20 LB8503V [CVO and CVI Pins] These pins determine the origin of the slope. (To set the origin to 0% at 0 rpm, short CVO to CVI.) 1. X axis shift (Resistor dividing the CVO to ground potential) (RPM) Motor full speed X axis shift 0% 100% CTL Duty (%) To shift the characteristics from a 0% = 0 rpm origin to a situation where the speed at a duty of 30% is shifted to 0%: First, determine the required CVI pin input voltage at 0%. CVI = 6 - (4 × DUTY) = 6 - (4 × 0.3) = 6 - 1.2 = 4.8V Next, when CVO is 6V, determine the resistor values for the resistor divider between CVO and ground such that the midpoint becomes 4.8V. CVO - CVI : CVI - ground = 1.2V : 4.8V = a ratio of 1 : 4. From the above, the desired resistor values will be 20kΩ between CVO and CVI and 80kΩ between CVI and ground. Note that the slope will change. (In this case, since the resistor ratio is 1:4, the result will be 4/5 of (or 0.8 times) the original slope.) If required, the RC pin resistor value must be changed to correct the slope. LIM VREF SOFT CVI R4 CVO R5 C CTL CTL ILB01773 No.A0366-10/20 LB8503V 2. Y axis shift (Resistor dividing the CVO to VCC potential) (RPM) Motor full speed X axis shift 0% 100% CTL Duty (%) To shift the characteristics from a 0% = 0 rpm origin to a situation where the speed is 0 rpm at a duty of 30%: First, determine the required CVO pin input voltage at 0%. CVO = 6 - (4 × DUTY) = 6 - (4 × 0.25) = 6 - 1 = 5V Determine the resistor values such that at CVO = 5 V, CVI becomes 6V. CVO - CVI : CVI - VCC = 1 V : 6V = a ratio of 1:6. From the above, the desired resistor values will be 20kΩ between CVO and CVI and 80kΩ between CVI and ground. (Due to the current capability of the CVO pin, the total resistor value must exceed 100kΩ.) Note that the slope will change. (In this case, since the resistor ratio is 1:6, the result will be 6/7 of (or 0.86 times) the original slope.) If required, the RC pin resistor value must be changed to correct the slope. VCC LIM VREF R5 SOFT R4 CVI CVO C CTL CTL ILB01775 No.A0366-11/20 LB8503V [LIM Pin] The minimum speed is determined by the LIM pin voltage. (RPM) Motor full speed 10000 8000 6000 4000 Set minimum 2000 speed 0 0% 6V CTL Duty (%) CVO pin voltage (V) 100% 2V 1. Determine the ratio of the required minimum speed and the maximum speed. Ra = minimum speed/maximum speed......... (1) In the example in the figure above, Ra = minimum speed/maximum speed = 3000/10000 = 0.3 2. Determine the product of the duty that produces the maximum speed and the value from equation 1. Ca = maximum speed duty × Ra .................. (2) For example, Ca = maximum speed duty × Ra = 0.8 × 0.3 = 0.24 3. Determine the required LIM pin voltage LIM = 6 - (4 × Ca) ....................................... (3) For example, LIM = 6 - (4 × Ca) = 6 - (4 × 0.24) ≈ 5V 4. Generate the LIM voltage by resistor dividing the 6 V regulator voltage. For example, the resistor ratio to create a 5V level will be 1:5. Thus the resistor values will be 10kΩ between 6VREG and LIM and 51kΩ between LIM and ground. 6VREG LIM VREF SOFT CVI ILB01777 No.A0366-12/20 LB8503V [C Pin] Since a capacitor that can smooth the pin voltage is connected to the C pin, if the CTL pin input signal frequency is f (Hz), then the capacitor must meet the following condition. (Here, R is the IC internal resistance of 180Ω (typical).) 1/f = t < RC Note that the larger the capacitor, the slower its response to changes in the input signal will be. 6VREG A capacitor that can smooth the pin voltage is connected here. 1/f = t < CR CTL pin input inverted waveform (the frequency is the same) C pin 180kΩ CTL pin CTL circuit VREF circuit No.A0366-13/20 LB8503V Application Example 2 [Setting the minimum speed for an origin of 0% = 0 rpm] (RPM) Motor full speed Set minimum speed 0% 100% PWM Duty(%) LB8503V 12V VCC C4 VREG FGOUT VREG 6VREG EDGE C5 FG FG FGIN R3 C3 RC One-shot multivibrator R1 C6 R2 C1 EI LIM C2 VREF EO1 VTH SOFT CVI CVO VREG EO3 C CTL signal CTL CTL GND When the speed control diagram origin is 0% = 0 rpm, the CVO pin is connected to the CVI pin. If the minimum speed is not set, connect the LIM pin to the 6VREG pin. No.A0366-14/20 LB8503V Application Example 3 [Origin shift in the Y direction (the motor turns at 0%)] (RPM) Motor full speed 0% 100% PWM Duty(%) LB8503V 12V VCC C4 VREG FGOUT VREG 6VREG EDGE C5 FG FG FGIN R3 RC C3 One-shot multivibrator EI C6 LIM C2 VREF C1 EO1 VTH SOFT CVI R4 CVO VREG R5 EO3 C CTL signal CTL CTL GND When the speed control diagram origin is set so the motor turns at 0%, the CVO pin to ground potential difference is resistor divided and the midpoint is input to the CVI pin. The speed at 0% can be changed with the resistor ratio. No.A0366-15/20 LB8503V Application Example 4 [Origin shift in the X axis direction (The motor turns at a duty of 10% or higher) plus a minimum speed setting] (RPM) Motor full speed 0% 100% PWM Duty(%) LB8503V 12V VCC C4 VREG FGOUT VREG 6VREG EDGE C5 FG FG FGIN R3 RC C3 One-shot multivibrator EI C6 LIM C2 VREF C1 EO1 VTH SOFT CVI R5 R4 CVO VREG EO3 C CTL signal CTL CTL GND When the origin in the speed control diagram is set so that the motor starts turning when the duty is above 0%. the potential difference between the CVO pin and VCC is resistor divided, and that divided level is input to the CVI pin. The duty at which rotation starts can be changed by changing the resistor ratio. Note that the total value of the resistors R4 and R5 must exceed 100kΩ. No.A0366-16/20 LB8503V Application Example 5 [DC Voltage Speed Control] (RPM) Motor full speed Set minimum speed 0 6V 2V CV1 pin voltage (V) LB8503V 12V VCC C4 VREG FGOUT VREG C5 6VREG EDGE FG FG FGIN R3 C3 RC One-shot multivibrator R1 C6 R2 DC voltage EI LIM SOFT CVI CVO C2 EO1 VREF VTH VREG EO3 C CTL CTL GND When the motor speed is controlled by a DC voltage, that voltage must be in the range from 2V to 6VREG. Note that the motor stops when the control voltage is at 6VREG, and the motor speed increases as the voltage falls. No.A0366-17/20 LB8503V Application Example 6 [Fixed Speed + Soft Start] (RPM) Motor full speed 0% 20% 40% 60% 80% 100% CTL signal (PWM duty) C pin voltage 6V LB8503V 12V VCC C4 VREG FGOUT VREG C5 6VREG EDGE FG FG FGIN R3 C3 RC One-shot multivibrator R1 C6 R2 EI LIM C2 VREF EO1 VTH SOFT CVI CVO VREG EO3 C CTL CTL GND With this circuit, the motor speed remains constant even if there are fluctuations in the supply voltage or static voltage. It is also possible to input a fixed-duty signal to the CTL pin signal input as an input signal for which soft start is enabled at startup. No.A0366-18/20 LB8503V Application Example 7 [Used in Combination with the LB11660FV] LB8503V 12V VCC C4 LB11660FV/RV VREG FGOUT VREG 6VREG EDGE C5 FG FG FGIN R3 RC C3 One-shot multivibrator R1 EI C6 LIM R2 C2 EO1 VREF C1 SOFT CVI R4 VTH CVO VREG R5 EO3 C CTL signal CTL CTL GND In this circuit, the dynamic range of the LB8503V EO pin (the range from the amplifier block output high to output low levels) must be wider than the dynamic range (from the high to low levels of the PWM signal) of VTH pin of driver IC with which this IC is combined. However, since the LB11660FV PWM low-level voltage is lower than the LB8503V amplifier output low-level voltage, it must be resistor divided. No.A0366-19/20 LB8503V SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein. SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are controlled under any of applicable local export control laws and regulations, such products may require the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written consent of SANYO Semiconductor Co.,Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO Semiconductor Co.,Ltd. product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. Upon using the technical information or products described herein, neither warranty nor license shall be granted with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's intellctual property rights which has resulted from the use of the technical information and products mentioned above. This catalog provides information as of March, 2007. Specifications and information herein are subject to change without notice. PS No.A0366-20/20